Abstract: A Comparison and evaluation of the different
condition monitoring (CM) techniques was applied experimentally
on RC e.g. Dynamic cylinder pressure and crankshaft Instantaneous
Angular Speed (IAS), for the detection and diagnosis of valve faults
in a two - stage reciprocating compressor for a programme of
condition monitoring which can successfully detect and diagnose a
fault in machine. Leakage in the valve plate was introduced
experimentally into a two-stage reciprocating compressor. The effect
of the faults on compressor performance was monitored and the
differences with the normal, healthy performance noted as a fault
signature been used for the detection and diagnosis of faults.
The paper concludes with what is considered to be a unique
approach to condition monitoring. First, each of the two most useful
techniques is used to produce a Truth Table which details the
circumstances in which each method can be used to detect and
diagnose a fault. The two Truth Tables are then combined into a
single Decision Table to provide a unique and reliable method of
detection and diagnosis of each of the individual faults introduced
into the compressor. This gives accurate diagnosis of compressor
faults.
Abstract: 17α-ethynylestradiol (EE2) is a synthetic estrogen
used as a key ingredient in an oral contraceptives pill. EE2 is an
endocrine disrupting compound, high in estrogenic potency.
Although EE2 exhibits low degree of biodegradability with common
microorganisms in wastewater treatment plants (WWTPs), this
compound can be biotransformed by ammonia-oxidizing bacteria
(AOB) via a co-metabolism mechanism in WWTPs. This study
aimed to investigate the effect of real wastewater on
biotransformation of EE2 by AOB. A preliminary experiment on the
effect of nitrite and pH levels on abiotic transformation of EE2
suggested that the abiotic transformation occurred at only pH
Abstract: The temporal nature of negative selection is an under exploited area. In a negative selection system, newly generated antibodies go through a maturing phase, and the survivors of the phase then wait to be activated by the incoming antigens after certain number of matches. These without having enough matches will age and die, while these with enough matches (i.e., being activated) will become active detectors. A currently active detector may also age and die if it cannot find any match in a pre-defined (lengthy) period of time. Therefore, what matters in a negative selection system is the dynamics of the involved parties in the current time window, not the whole time duration, which may be up to eternity. This property has the potential to define the uniqueness of negative selection in comparison with the other approaches. On the other hand, a negative selection system is only trained with “normal" data samples. It has to learn and discover unknown “abnormal" data patterns on the fly by itself. Consequently, it is more appreciate to utilize negation selection as a system for pattern discovery and recognition rather than just pattern recognition. In this paper, we study the potential of using negative selection in discovering unknown temporal patterns.
Abstract: Sliding mode control with a fuzzy boundary layer is presented to hydraulic position control problem in this paper. A nonlinear hydraulic servomechanism which has an asymmetric cylinder is modeled and simulated first, then the proposed control scheme is applied to this model versus the conventional sliding mode control. Simulation results proved that the chattering free position control is achieved by tuning the fuzzy scaling factors properly.
Abstract: In recent years, scanning probe atomic force
microscopy SPM AFM has gained acceptance over a wide spectrum
of research and science applications. Most fields focuses on physical,
chemical, biological while less attention is devoted to manufacturing
and machining aspects. The purpose of the current study is to assess
the possible implementation of the SPM AFM features and its
NanoScope software in general machining applications with special
attention to the tribological aspects of cutting tool. The surface
morphology of coated and uncoated as-received carbide inserts is
examined, analyzed, and characterized through the determination of
the appropriate scanning setting, the suitable data type imaging
techniques and the most representative data analysis parameters
using the MultiMode SPM AFM in contact mode. The NanoScope
operating software is used to capture realtime three data types
images: “Height", “Deflection" and “Friction". Three scan sizes are
independently performed: 2, 6, and 12 μm with a 2.5 μm vertical
range (Z). Offline mode analysis includes the determination of three
functional topographical parameters: surface “Roughness", power
spectral density “PSD" and “Section". The 12 μm scan size in
association with “Height" imaging is found efficient to capture every
tiny features and tribological aspects of the examined surface. Also,
“Friction" analysis is found to produce a comprehensive explanation
about the lateral characteristics of the scanned surface. Configuration
of many surface defects and drawbacks has been precisely detected
and analyzed.
Abstract: In this paper, to resolve the problem of existing
schemes, an alternative fast handover Proxy Mobile IPv6 (PMIPv6)
scheme using the IEEE 802.21 Media Independent Handover (MIH)
function is proposed for heterogeneous wireless networks. The proposed
scheme comes to support fast handover for the mobile node
(MN) irrespective of the presence or absence of MIH functionality
as well as L3 mobility functionality, whereas the MN in existing
schemes has to implement MIH functionality. That is, the proposed
scheme does not require the MN to be involved in MIH related signaling
required for handover procedure. The base station (BS) with MIH
functionality performs handover on behalf of the MN. Therefore, the
proposed scheme can reduce burden and power consumption of MNs
with limited resource and battery power since MNs are not required
to be involved for the handover procedure. In addition, the proposed
scheme can reduce considerably traffic overhead over wireless links
between MN and BS since signaling messages are reduced.
Abstract: A simple mobile engine-driven pneumatic paddy
collector made of locally available materials using local
manufacturing technology was designed, fabricated, and tested for
collecting and bagging of paddy dried on concrete pavement. The
pneumatic paddy collector had the following major components:
radial flat bladed type centrifugal fan, power transmission system,
bagging area, frame and the conveyance system. Results showed
significant differences on the collecting capacity, noise level, and fuel
consumption when rotational speed of the air mover shaft was varied.
Other parameters such as collecting efficiency, air velocity,
augmented cracked grain percentage, and germination rate were not
significantly affected by varying rotational speed of the air mover
shaft. The pneumatic paddy collector had a collecting efficiency of
99.33 % with a collecting capacity of 2685.00 kg/h at maximum
rotational speed of centrifugal fan shaft of about 4200 rpm. The
machine entailed an investment cost of P 62,829.25. The break-even
weight of paddy was 510,606.75 kg/yr at a collecting cost of 0.11
P/kg of paddy. Utilizing the machine for 400 hours per year
generated an income of P 23,887.73. The projected time needed to
recover cost of the machine based on 2685 kg/h collecting capacity
was 2.63 year.
Abstract: A traffic light gives security from traffic congestion,reducing the traffic jam, and organizing the traffic flow. Furthermore,increasing congestion level in public road networks is a growingproblem in many countries. Using Intelligent Transportation Systemsto provide emergency vehicles a green light at intersections canreduce driver confusion, reduce conflicts, and improve emergencyresponse times. Nowadays, the technology of wireless sensornetworks can solve many problems and can offer a good managementof the crossroad. In this paper, we develop a new approach based onthe technique of clustering and the graphical possibilistic fusionmodeling. So, the proposed model is elaborated in three phases. Thefirst one consists to decompose the environment into clusters,following by the fusion intra and inter clusters processes. Finally, wewill show some experimental results by simulation that proves theefficiency of our proposed approach.KeywordsTraffic light, Wireless sensor network, Controller,Possibilistic network/Bayesain network.
Abstract: In this study, rotating flexible shaft-disk system
having flexible beams is considered as a dynamic system. After
neglecting nonlinear terms, torsional vibration of the shaft-disk
system and lateral and longitudinal vibration of the flexible beam are
still coupled through the motor speed. The system has three natural
frequencies; the flexible shaft-disk system torsional natural
frequency, the flexible beam lateral and longitudinal natural
frequencies. Eigenvalue calculations show that while the shaft speed
changes, torsional natural frequency of the shaft-disk system and the
beam longitudinal natural frequency are not changing but the beam
lateral natural frequency changes. Beam lateral natural frequency
stays the same as the nonrotating beam lateral natural frequency ωb
until the motor speed ωm is equal to ωb. After then ωb increases and
remains equal to the motor speed ωm until the motor speed is equal to
the shaft-disk system natural frequency ωT. Then the beam lateral
natural frequency ωb becomes equal to the natural frequency ωT and
stays same while the motor speed ωm is increased. Modal amplitudes
and phase angles of the vibrations are also plotted against the motor
speed ωm.
Abstract: Finding effective ways of improving university quality assurance requires, as well, a retraining of the staff. This article illustrates an Online Programme of Excellence Model (OPEM), based on the European quality assurance model, for improving participants- formative programme standards. The results of applying this OPEM indicate the necessity of quality policies that support the evaluators- competencies to improve formative programmes. The study concludes by outlining how faculty and agency staff can use OPEM for the internal and external quality assurance of formative programmes.
Abstract: Car accident is one of the major causes of death in many countries. Many researchers have attempted to design and develop techniques to increase car safety in the past recent years. In spite of all the efforts, it is still challenging to design a system adaptive to the driver rather than the automotive characteristics. In this paper, the adaptive car safety system is explained which attempts to find a balance.
Abstract: This study presents a new approach based on Tanaka's
fuzzy linear regression (FLP) algorithm to solve well-known power
system economic load dispatch problem (ELD). Tanaka's fuzzy linear
regression (FLP) formulation will be employed to compute the
optimal solution of optimization problem after linearization. The
unknowns are expressed as fuzzy numbers with a triangular
membership function that has middle and spread value reflected on
the unknowns. The proposed fuzzy model is formulated as a linear
optimization problem, where the objective is to minimize the sum of
the spread of the unknowns, subject to double inequality constraints.
Linear programming technique is employed to obtain the middle and
the symmetric spread for every unknown (power generation level).
Simulation results of the proposed approach will be compared with
those reported in literature.
Abstract: Recent theorizations on the cognitive process of moral
judgment have focused on the role of intuitions and emotions, marking
a departure from previous emphasis on conscious, step-by-step
reasoning. My study investigated how being in a disgusted mood state
affects moral judgment.
Participants were induced to enter a disgusted mood state through
listening to disgusting sounds and reading disgusting descriptions.
Results shows that they, when compared to control who have not been
induced to feel disgust, are more likely to endorse actions that are
emotionally aversive but maximizes utilitarian return
The result is analyzed using the 'emotion-as-information' approach
to decision making. The result is consistent with the view that
emotions play an important role in determining moral judgment.
Abstract: This paper present an effective method to accurately reconstruct and measure the 3D curve edges of small industrial parts based on stereo vision. To effectively fit the curve of the measured parts using a series of line segments in the images, a strategy from coarse to fine is employed based on multi-scale curve fitting. After reconstructing the 3D curve of a hole through a curved surface, its axis is adjusted so that it is parallel to the Z axis with least squares error and the dimensions of the hole can be calculated on the XY plane easily. Experimental results show that the presented method can accurately measure the dimensions of round holes through a curved surface.
Abstract: Logistics is part of the supply chain processes that plans, implements, and controls the efficient and effective forward and reverse flow and storage of goods, services, and related information between the point of origin and the point of consumption in order to meet customer requirements. This research aims to investigate the current status and future direction of the use of Information Technology (IT) for logistics, focusing on Supply Chain Management (SCM) and E-Commerce adoption in Johor. Therefore, this research stresses on the type of technology being adopted, factors, benefits and barriers affecting the innovation in SCM and ECommerce technology adoption among Logistics Service Providers (LSP). A mailed questionnaire survey was conducted to collect data from 265 logistics companies in Johor. The research revealed that SCM technology adoption among LSP was higher as they had adopted SCM technology in various business processes while they perceived a high level of benefits from SCM adoption. Obviously, ECommerce technology adoption among LSP is relatively low.
Abstract: The effect of wheat flour extraction rates on flour
composition, farinographic characteristics and the quality of
sourdough naans was investigated. The results indicated that by
increasing the extraction rate, the amount of protein, fiber, fat and
ash increased, whereas moisture content decreased. Farinographic
characteristic like water absorption and dough development time
increased with an increase in flour extraction rate but the dough
stabilities and tolerance indices were reduced with an increase in
flour extraction rates. Titratable acidity for both sourdough and
sourdough naans also increased along with flour extraction rate. The
study showed that overall quality of sourdough naans were affected
by both flour extraction rate and starter culture used. Sensory
analysis of sourdough naans revealed that desirable extraction rate
for sourdough naan was 76%.
Abstract: The object of this research is the design and
evaluation of an immersive Virtual Learning Environment (VLE) for
deaf children. Recently we have developed a prototype immersive
VR game to teach sign language mathematics to deaf students age K-
4 [1] [2]. In this paper we describe a significant extension of the
prototype application. The extension includes: (1) user-centered
design and implementation of two additional interactive
environments (a clock store and a bakery), and (2) user-centered
evaluation including development of user tasks, expert panel-based
evaluation, and formative evaluation. This paper is one of the few to
focus on the importance of user-centered, iterative design in VR
application development, and to describe a structured evaluation
method.
Abstract: In this paper the behavior of fixed series compensated
extra high voltage transmission lines during faults is simulated. Many
over-voltage protection schemes for series capacitors are limited in
terms of size and performance, and are easily affected by
environmental conditions. While the need for more compact and
environmentally robust equipment is required. use of series
capacitors for compensating part of the inductive reactance of long
transmission lines increases the power transmission capacity.
Emphasis is given on the impact of modern capacitor protection
techniques (MOV protection). The simulation study is performed
using MATLAB/SIMULINK®and results are given for a three phase
and a single phase to ground fault.
Abstract: Due to the complex network architecture, the mobile
adhoc network-s multihop feature gives additional problems to the
users. When the traffic load at each node gets increased, the
additional contention due its traffic pattern might cause the nodes
which are close to destination to starve the nodes more away from the
destination and also the capacity of network is unable to satisfy the
total user-s demand which results in an unfairness problem. In this
paper, we propose to create an algorithm to compute the optimal
MAC-layer bandwidth assigned to each flow in the network. The
bottleneck links contention area determines the fair time share which
is necessary to calculate the maximum allowed transmission rate used
by each flow. To completely utilize the network resources, we
compute two optimal rates namely, the maximum fair share and
minimum fair share. We use the maximum fair share achieved in
order to limit the input rate of those flows which crosses the
bottleneck links contention area when the flows that are not allocated
to the optimal transmission rate and calculate the following highest
fair share. Through simulation results, we show that the proposed
protocol achieves improved fair share and throughput with reduced
delay.
Abstract: This paper describes an optimal approach for feature
subset selection to classify the leaves based on Genetic Algorithm
(GA) and Kernel Based Principle Component Analysis (KPCA). Due
to high complexity in the selection of the optimal features, the
classification has become a critical task to analyse the leaf image
data. Initially the shape, texture and colour features are extracted
from the leaf images. These extracted features are optimized through
the separate functioning of GA and KPCA. This approach performs
an intersection operation over the subsets obtained from the
optimization process. Finally, the most common matching subset is
forwarded to train the Support Vector Machine (SVM). Our
experimental results successfully prove that the application of GA
and KPCA for feature subset selection using SVM as a classifier is
computationally effective and improves the accuracy of the classifier.