Abstract: In this paper, a fibre laser at 546 nm has been studied
for a signal power of -30 dB. Er3+-doped ZBLAN fibre has been used
by upconversion pumping of a 980 nm laser diode. Gain saturation
effect has been investigated in detail. Laser performance has also been
discussed. An efficiency of 35% has been calculated with a length of 5
mm fibre laser. Results show that Er3+-doped ZBLAN is a promising
candidate for optical amplification at 546 nm.
Abstract: The launching nose plays an important role in the
incremental launching construction. The parameters of the launching
nose essentially affect the internal forces of the girder during the
construction. The appropriate parameters can decrease the internal
forces in the girder and save the material and reduce the cost. The
simplified structural model, which is made with displacement method
according to the characteristic of incremental launching construction
and the variation rule of the internal forces, calculates and analyzes the
effect of the length, the rigidity and weight of launch nose on the
internal forces of girder during the incremental launching
construction. The method, which can calculate the launching nose
parameters for the optimum incremental launching construction, is
achieved. This method is simple, reliable and easy for practical use.
Abstract: Among all mechanical joining processes, welding has
been employed for its advantage in design flexibility, cost saving,
reduced overall weight and enhanced structural performance.
However, for structures made of relatively thin components, welding
can introduce significant buckling distortion which causes loss of
dimensional control, structural integrity and increased fabrication
costs. Different parameters can affect buckling behavior of welded
thin structures such as, heat input, welding sequence, dimension of
structure. In this work, a 3-D thermo elastic-viscoplastic finite
element analysis technique is applied to evaluate the effect of shell
dimensions on buckling behavior and entropy generation of welded
thin shells. Also, in the present work, the approximated longitudinal
transient stresses which produced in each time step, is applied to the
3D-eigenvalue analysis to ratify predicted buckling time and
corresponding eigenmode. Besides, the possibility of buckling
prediction by entropy generation at each time is investigated and it is
found that one can predict time of buckling with drawing entropy
generation versus out of plane deformation. The results of finite
element analysis show that the length, span and thickness of welded
thin shells affect the number of local buckling, mode shape of global
buckling and post-buckling behavior of welded thin shells.
Abstract: This paper discusses on the use of Spline Interpolation
and Mean Square Error (MSE) as tools to process data acquired from
the developed simulator that shall replicate sea bed logging environment.
Sea bed logging (SBL) is a new technique that uses marine
controlled source electromagnetic (CSEM) sounding technique and is
proven to be very successful in detecting and characterizing hydrocarbon
reservoirs in deep water area by using resistivity contrasts. It uses
very low frequency of 0.1Hz to 10 Hz to obtain greater wavelength.
In this work the in house built simulator was used and was provided
with predefined parameters and the transmitted frequency was varied
for sediment thickness of 1000m to 4000m for environment with and
without hydrocarbon. From series of simulations, synthetics data were
generated. These data were interpolated using Spline interpolation
technique (degree of three) and mean square error (MSE) were
calculated between original data and interpolated data. Comparisons
were made by studying the trends and relationship between frequency
and sediment thickness based on the MSE calculated. It was found
that the MSE was on increasing trends in the set up that has the
presence of hydrocarbon in the setting than the one without. The MSE
was also on decreasing trends as sediment thickness was increased
and with higher transmitted frequency.
Abstract: Elastic light single-scattering spectroscopy system
with a single optical fiber probe was employed to differentiate cancerous prostate tissue from non-cancerous prostate tissue ex-vivo just after radical prostatectomy. First, ELSSS spectra were acquired
from cancerous prostate tissue to define its spectral features. Then,
spectra were acquired from normal prostate tissue to define difference in spectral features between the cancerous and normal
prostate tissues. Of the total 66 tissue samples were evaluated from
nine patients by ELSSS system. Comparing of histopathology results
and ELSSS measurements revealed that sign of the spectral slopes of
cancerous prostate tissue is negative and non-cancerous tissue is positive in the wavelength range from 450 to 750 nm. Based on the
correlation between histopathology results and sign of the spectral
slopes, ELSSS system differentiates cancerous prostate tissue from
non- cancerous with a sensitivity of 0.95 and a specificity of 0.94.
Abstract: The Yasuj city stream named the Beshar supply
water for different usages such as aquaculture farms , drinking,
agricultural and industrial usages. Fish processing plants
,Agricultural farms, waste water of industrial zones and hospitals
waste water which they are generate by human activity produce a
considerable volume of effluent and when they are released in to the
stream they can effect on the water quality and down stream aquatic
systems. This study was conducted to evaluate the effects of outflow
effluent from different human activity and point and non point
pollution sources on the water quality and health of the Beshar
river next to Yasuj. Yasuj is the biggest and most important city in
the Kohkiloye and Boyerahmad province . The Beshar River is one
of the most important aquatic ecosystems in the upstream of the
Karun watershed in south of Iran which is affected by point and non
point pollutant sources . This study was done in order to evaluate the
effects of human activities on the water quality and health of the
Beshar river. This river is approximately 190 km in length and
situated at the geographical positions of 51° 20' to 51° 48' E and 30°
18' to 30° 52' N it is one of the most important aquatic ecosystems of
Kohkiloye and Boyerahmad province in south-west Iran. In this
research project, five study stations were selected to examine water
pollution in the Beshar River systems. Human activity is now one of
the most important factors affecting on hydrology and water quality
of the Beshar river. Humans use large amounts of resources to sustain
various standards of living, although measures of sustainability are
highly variable depending on how sustainability is defined. The
Beshar river ecosystems are particularly sensitive and vulnerable to
human activities. The water samples were analyzed, then some
important water quality parameters such as pH, dissolve oxygen
(DO), Biochemical Oxygen Demand (BOD5), Chemical Oxygen
Demand (COD), Total Suspended Solids (TDS),Turbidity,
Temperature, Nitrates (NO3) and Phosphates (PO4) were estimated
at the two stations. The results show a downward trend in the water
quality at the down stream of the city. The amounts of
BOD5,COD,TSS,T,Turbidity, NO3 and PO4 in the down stream
stations were considerably more than the station 1. By contrast the
amounts of DO in the down stream stations were less than to the
station 1. However when effluent discharge consequence of human
activities are released into the Beshar river near the city, the quality
of river are decreases and the environmental problems of the river
during the next years are predicted to rise.
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: We prove detailed analysis of a waveguide-based Schottky barrier photodetector (SBPD) where a thin silicide film is put on the top of a silicon-on-insulator (SOI) channel waveguide to absorb light propagating along the waveguide. Taking both the confinement factor of light absorption and the wall scanning induced gain of the photoexcited carriers into account, an optimized silicide thickness is extracted to maximize the effective gain, thereby the responsivity. For typical lengths of the thin silicide film (10-20 Ðçm), the optimized thickness is estimated to be in the range of 1-2 nm, and only about 50-80% light power is absorbed to reach the maximum responsivity. Resonant waveguide-based SBPDs are proposed, which consist of a microloop, microdisc, or microring waveguide structure to allow light multiply propagating along the circular Si waveguide beneath the thin silicide film. Simulation results suggest that such resonant waveguide-based SBPDs have much higher repsonsivity at the resonant wavelengths as compared to the straight waveguidebased detectors. Some experimental results about Si waveguide-based SBPD are also reported.
Abstract: The objective from this paper is to design a solar
thermal engine for space vehicles orbital control and electricity
generation. A computational model is developed for the prediction of
the solar thermal engine performance for different design parameters and conditions in order to enhance the engine efficiency. The engine is divided into two main subsystems. First, the concentrator dish
which receives solar energy from the sun and reflects them to the
cavity receiver. The second one is the cavity receiver which receives
the heat flux reflected from the concentrator and transfers heat to the
fluid passing over. Other subsystems depend on the application required from the engine. For thrust application, a nozzle is
introduced to the system for the fluid to expand and produce thrust.
Hydrogen is preferred as a working fluid in the thruster application.
Results model developed is used to determine the thrust for a
concentrator dish 4 meters in diameter (provides 10 kW of energy),
focusing solar energy to a 10 cm aperture diameter cavity receiver.
The cavity receiver outer length is 50 cm and the internal cavity is 47
cm in length. The suggested design material of the internal cavity is
tungsten to withstand high temperature. The thermal model and
analysis shows that the hydrogen temperature at the plenum reaches
2000oK after about 250 seconds for hot start operation for a flow rate
of 0.1 g/sec.Using solar thermal engine as an electricity generation
device on earth is also discussed. In this case a compressor and
turbine are used to convert the heat gained by the working fluid (air)
into mechanical power. This mechanical power can be converted into
electrical power by using a generator.
Abstract: This study shows palynomorphological description of
pollen grains of Lamium garganicum, species of the family Labiatae.
Fresh material of this plant is taken in Mount Llogara, in Albania. By
comparison made between palinomorphological characteristics of
pollen grains of Lamium garganicum with those of Lamium
maculatum and Lamium purpureum, showed that granules have
similarities in the number of furrows. The pollen grains of Lamium
garganicum were larger in length and width than those of Lamium
maculatum and almost equal with those of Lamium purpureum.
Furrows are longer than those of pollen grains in Lamium maculatum
and shorter than those of Lamium purpureum. The layer of exine of
Lamium garganicum was thinner than that of two others. The
sculpture of exine was fine reticulate, where reticulas were uniform
whereas in Lamium purpureum was verrucate, with small verrucae; in
Lamium maculatum was reticulate.
Abstract: This article considers the positional buckling of
composite thick plates under thermal loading . For this purpose , the
complex finite strip method is used . In analysis of complex finite
strip, harmonic complex function in longitudinal direction , cubic
functions in transversal direction and parabola distribution of
transverse shear strain in thickness of thick plate based on higherorder
shear deformation theory are used . In given examples , the
effect of angles of stratification , number of layers , dimensions ratio
and length – to – thick ratio across critical temperature are
considered.
Abstract: In this paper we investigate numerically positive solutions of the equation -Δu = λuq+up with Dirichlet boundary condition in a boundary domain ╬® for λ > 0 and 0 < q < 1 < p < 2*, we will compute and visualize the range of λ, this problem achieves a numerical solution.
Abstract: This paper presents a novel genetic algorithm, termed
the Optimum Individual Monogenetic Algorithm (OIMGA) and
describes its hardware implementation. As the monogenetic strategy
retains only the optimum individual, the memory requirement is
dramatically reduced and no crossover circuitry is needed, thereby
ensuring the requisite silicon area is kept to a minimum.
Consequently, depending on application requirements, OIMGA
allows the investigation of solutions that warrant either larger GA
populations or individuals of greater length. The results given in this
paper demonstrate that both the performance of OIMGA and its
convergence time are superior to those of existing hardware GA
implementations. Local convergence is achieved in OIMGA by
retaining elite individuals, while population diversity is ensured by
continually searching for the best individuals in fresh regions of the
search space.
Abstract: The objective of this paper is to present explicit analytical formulas for evaluating important characteristics of Double Moving Average control chart (DMA) for Poisson distribution. The most popular characteristics of a control chart are Average Run Length ( 0 ARL ) - the mean of observations that are taken before a system is signaled to be out-of control when it is actually still incontrol, and Average Delay time ( 1 ARL ) - mean delay of true alarm times. An important property required of 0 ARL is that it should be sufficiently large when the process is in-control to reduce a number of false alarms. On the other side, if the process is actually out-ofcontrol then 1 ARL should be as small as possible. In particular, the explicit analytical formulas for evaluating 0 ARL and 1 ARL be able to get a set of optimal parameters which depend on a width of the moving average ( w ) and width of control limit ( H ) for designing DMA chart with minimum of 1 ARL
Abstract: In the study of honeycomb crushing under quasistatic loading, two parameters are important, the mean crushing stress and the wavelength of the folding mode. The previous theoretical models did not consider the true cylindrical curvature effects and the flow stress in the folding mode of honeycomb material. The present paper introduces a modification on Wierzbicki-s model based on considering two above mentioned parameters in estimating the mean crushing stress and the wavelength through implementation of the energy method. Comparison of the results obtained by the new model and Wierzbicki-s model with existing experimental data shows better prediction by the model presented in this paper.
Abstract: One of the purposes of the robust method of
estimation is to reduce the influence of outliers in the data, on the
estimates. The outliers arise from gross errors or contamination from
distributions with long tails. The trimmed mean is a robust estimate.
This means that it is not sensitive to violation of distributional
assumptions of the data. It is called an adaptive estimate when the
trimming proportion is determined from the data rather than being
fixed a “priori-.
The main objective of this study is to find out the robustness
properties of the adaptive trimmed means in terms of efficiency, high
breakdown point and influence function. Specifically, it seeks to find
out the magnitude of the trimming proportion of the adaptive
trimmed mean which will yield efficient and robust estimates of the
parameter for data which follow a modified Weibull distribution with
parameter λ = 1/2 , where the trimming proportion is determined by a
ratio of two trimmed means defined as the tail length. Secondly, the
asymptotic properties of the tail length and the trimmed means are
also investigated. Finally, a comparison is made on the efficiency of
the adaptive trimmed means in terms of the standard deviation for the
trimming proportions and when these were fixed a “priori".
The asymptotic tail lengths defined as the ratio of two trimmed
means and the asymptotic variances were computed by using the
formulas derived. While the values of the standard deviations for the
derived tail lengths for data of size 40 simulated from a Weibull
distribution were computed for 100 iterations using a computer
program written in Pascal language.
The findings of the study revealed that the tail lengths of the
Weibull distribution increase in magnitudes as the trimming
proportions increase, the measure of the tail length and the adaptive
trimmed mean are asymptotically independent as the number of
observations n becomes very large or approaching infinity, the tail
length is asymptotically distributed as the ratio of two independent
normal random variables, and the asymptotic variances decrease as
the trimming proportions increase. The simulation study revealed
empirically that the standard error of the adaptive trimmed mean
using the ratio of tail lengths is relatively smaller for different values
of trimming proportions than its counterpart when the trimming
proportions were fixed a 'priori'.
Abstract: The paper presents an analytical solution for dispersion
of a solute in the peristaltic motion of a micropolar fluid in the
presence of magnetic field and both homogeneous and heterogeneous
chemical reactions. The average effective dispersion coefficient has
been found using Taylor-s limiting condition under long wavelength
approximation. The effects of various relevant parameters on the average
coefficient of dispersion have been studied. The average effective
dispersion coefficient increases with amplitude ratio, cross viscosity
coefficient and heterogeneous chemical reaction rate parameter. But it
decreases with magnetic field parameter and homogeneous chemical
reaction rate parameter. It can be noted that the presence of peristalsis
enhances dispersion of a solute.
Abstract: Traffic congestion has become a major problem in
many countries. One of the main causes of traffic congestion is due
to road merges. Vehicles tend to move slower when they reach the
merging point. In this paper, an enhanced algorithm for traffic
simulation based on the fluid-dynamic algorithm and kinematic wave
theory is proposed. The enhanced algorithm is used to study traffic
congestion at a road merge. This paper also describes the
development of a dynamic traffic simulation tool which is used as a
scenario planning and to forecast traffic congestion level in a certain
time based on defined parameter values. The tool incorporates the
enhanced algorithm as well as the two original algorithms. Output
from the three above mentioned algorithms are measured in terms of
traffic queue length, travel time and the total number of vehicles
passing through the merging point. This paper also suggests an
efficient way of reducing traffic congestion at a road merge by
analyzing the traffic queue length and travel time.
Abstract: The calculation of buckling length factor (K) for steel
frames columns is a major and governing processes to determine the
dimensions steel frame columns cross sections during design. The
buckling length of steel frames columns has a direct effect on the cost
(weight) of using cross section. A new formula is required to
determine buckling length factor (K) by simplified way. In this
research a new formula for buckling length factor (K) was established
to determine by accurate method for a limited interval of columns
ends rigidity (GA, GB). The new formula can be used ease to
evaluate the buckling length factor without needing to complicated
equations or difficult charts.
Abstract: We propose a decoy-pulse protocol for frequency-coded implementation of B92 quantum key distribution protocol. A direct extension of decoy-pulse method to frequency-coding scheme results in security loss as an eavesdropper can distinguish between signal and decoy pulses by measuring the carrier photon number without affecting other statistics. We overcome this problem by optimizing the ratio of carrier photon number of decoy-to-signal pulse to be as close to unity as possible. In our method the switching between signal and decoy pulses is achieved by changing the amplitude of RF signal as opposed to modulating the intensity of optical signal thus reducing system cost. We find an improvement by a factor of 100 approximately in the key generation rate using decoy-state protocol. We also study the effect of source fluctuation on key rate. Our simulation results show a key generation rate of 1.5×10-4/pulse for link lengths up to 70km. Finally, we discuss the optimum value of average photon number of signal pulse for a given key rate while also optimizing the carrier ratio.