Abstract: Cooperative communication scheme can be substituted
for multiple-input multiple-output (MIMO) technique when it may
not be able to support multiple antennas due to size, cost or
hardware limitations. In other words, cooperative communication
scheme is an efficient method to achieve spatial diversity without
multiple antennas. For satisfaction of rising QoS, we propose a
reliable cooperative communication scheme with M-QAM based Dual
Carrier Modulation (M-DCM), which can increase diversity gain.
Although our proposed scheme is very simple method, it gives us
frequency and spatial diversity. Simulation result shows our proposed
scheme obtains diversity gain more than the conventional cooperative
communication scheme.
Abstract: The objective of this paper is to analyze the
performance of a double-sided axial flux permanent magnet
brushless DC (AFPM BLDC) motor with two-phase winding.
To study the motor operation, a mathematical dynamic model
has been proposed for motor, which became the basis for
simulations that were performed using MATLAB/SIMULINK
software package. The results of simulations were presented
in form of the waveforms of selected quantities and the
electromechanical characteristics performed by the motor. The
calculation results show that the two-phase motor version
develops smooth torque and reaches high efficiency. The twophase
motor can be applied where more smooth torque is
required. Finally a study on the influence of switching angle
on motor performance shows that when advance switching
technique is used, the motor operates with the highest
efficiency.
Abstract: In this paper, novel techniques in increasing the accuracy
and speed of convergence of a Feed forward Back propagation
Artificial Neural Network (FFBPNN) with polynomial activation
function reported in literature is presented. These technique was
subsequently used to determine the coefficients of Autoregressive
Moving Average (ARMA) and Autoregressive (AR) system. The
results obtained by introducing sequential and batch method of weight
initialization, batch method of weight and coefficient update, adaptive
momentum and learning rate technique gives more accurate result
and significant reduction in convergence time when compared t the
traditional method of back propagation algorithm, thereby making
FFBPNN an appropriate technique for online ARMA coefficient
determination.
Abstract: The Siemens Healthcare Sector is one of the world's
largest suppliers to the healthcare industry and a trendsetter in
medical imaging and therapy, laboratory diagnostics, medical
information technology, and hearing aids.
Siemens offers its customers products and solutions for the entire
range of patient care from a single source – from prevention and
early detection to diagnosis, and on to treatment and aftercare. By
optimizing clinical workflows for the most common diseases,
Siemens also makes healthcare faster, better, and more cost effective.
The optimization of clinical workflows requires a
multidisciplinary focus and a collaborative approach of e.g. medical
advisors, researchers and scientists as well as healthcare economists.
This new form of collaboration brings together experts with deep
technical experience, physicians with specialized medical knowledge
as well as people with comprehensive knowledge about health
economics.
As Charles Darwin is often quoted as saying, “It is neither the
strongest of the species that survive, nor the most intelligent, but the
one most responsive to change," We believe that those who can
successfully manage this change will emerge as winners, with
valuable competitive advantage.
Current medical information and knowledge are some of the core
assets in the healthcare industry. The main issue is to connect
knowledge holders and knowledge recipients from various
disciplines efficiently in order to spread and distribute knowledge.
Abstract: This research’s objective is to select the model with
most accurate value by using Neural Network Technique as a way to
filter potential students who enroll in IT course by Electronic learning
at Suan Suanadha Rajabhat University. It is designed to help students
selecting the appropriate courses by themselves. The result showed
that the most accurate model was 100 Folds Cross-validation which
had 73.58% points of accuracy.
Abstract: Coal will continue to be the predominant source of
global energy for coming several decades. The huge generation of fly
ash (FA) from combustion of coal in thermal power plants (TPPs) is
apprehended to pose the concerns of its disposal and utilization. FA
application based on its typical characteristics as soil ameliorant for
agriculture and forestry is the potential area, and hence the global
attempt. The inferences drawn suffer from the variations of ash
characteristics, soil types, and agro-climatic conditions; thereby
correlating the effects of ash between various plant species and soil
types is difficult. Indian FAs have low bulk density, high water
holding capacity and porosity, rich silt-sized particles, alkaline
nature, negligible solubility, and reasonable plant nutrients. Findings
of the demonstrations trials for more than two decades from lab/pot
to field scale long-term experiments are developed as FA soil
amendment technology (FASAT) by Central Institute of Mining and
Fuel Research (CIMFR), Dhanbad. Performance of different crops
and plant species in cultivable and problematic soils, are
encouraging, eco-friendly, and being adopted by the farmers. FA
application includes ash alone and in combination with
inorganic/organic amendments; combination treatments including
bio-solids perform better than FA alone. Optimum dose being up to
100 t/ha for cultivable land and up to/ or above 200 t/ha of FA for
waste/degraded land/mine refuse, depending on the characteristics of
ash and soil. The elemental toxicity in Indian FA is usually not of
much concern owing to alkaline ashes, oxide forms of elements, and
elemental concentration within the threshold limits for soil
application. Combating toxicity, if any, is possible through
combination treatments with organic materials and phytoremediation.
Government initiatives through extension programme
involving farmers and ash generating organizations need to be
accelerated
Abstract: This paper presents performance comparison of three estimation techniques used for peak load forecasting in power systems. The three optimum estimation techniques are, genetic algorithms (GA), least error squares (LS) and, least absolute value filtering (LAVF). The problem is formulated as an estimation problem. Different forecasting models are considered. Actual recorded data is used to perform the study. The performance of the above three optimal estimation techniques is examined. Advantages of each algorithms are reported and discussed.
Abstract: This paper examines many mathematical methods for
molding the hourly price forward curve (HPFC); the model will be
constructed by numerous regression methods, like polynomial
regression, radial basic function neural networks & a furrier series.
Examination the models goodness of fit will be done by means of
statistical & graphical tools. The criteria for choosing the model will
depend on minimize the Root Mean Squared Error (RMSE), using the
correlation analysis approach for the regression analysis the optimal
model will be distinct, which are robust against model
misspecification. Learning & supervision technique employed to
determine the form of the optimal parameters corresponding to each
measure of overall loss. By using all the numerical methods that
mentioned previously; the explicit expressions for the optimal model
derived and the optimal designs will be implemented.
Abstract: Solidification cracking and hydrogen cracking are some defects generated in the fusion welding of ultrahigh carbon steels. However, friction stir welding (FSW) of such steels, being a solid-state technique, has been demonstrated to alleviate such problems encountered in traditional welding. FSW include different process parameters that must be carefully defined prior processing. These parameters included but not restricted to: tool feed, tool RPM, tool geometry, tool tilt angle. These parameters form a key factor behind avoiding warm holes and voids behind the tool and in achieving a defect-free weld. More importantly, these parameters directly affect the microstructure of the weld and hence the final mechanical properties of weld. For that, 3D finite element (FE) thermo-mechanical model was developed using DEFORM 3D to simulate FSW of carbon steel. At points of interest in the joint, tracking is done for history of critical state variables such as temperature, stresses, and strain rates. Typical results found include the ability to simulate different weld zones. Simulations predictions were successfully compared to experimental FSW tests. It is believed that such a numerical model can be used to optimize FSW processing parameters to favor desirable defect free weld with better mechanical properties.
Abstract: Unified Theory of Acceptance and Use of Technology
(UTAUT) model has demonstrated the influencing factors for generic
information systems use such as tablet personal computer (TPC) and
mobile communication. However, in the context of digital library
system, there has been very little effort to determine factors affecting
the intention to use digital library based on the UTAUT model. This
paper investigates factors that are expected to influence the intention
of postgraduate students to use digital library based on modified
UTAUT model. The modified model comprises of constructs
represented by several latent variables, namely performance
expectancy (PE), effort expectancy (EE), information quality (IQ)
and service quality (SQ) and moderated by age, gender and
experience in using digital library. Results show that performance
expectancy, effort expectancy and information quality are positively
related to the intention to use digital library, while service quality is
negatively related to the intention to use digital library. Age and
gender have shown no evidence of any significant interactions, while
experience in using digital library significantly interacts with effort
expectancy and intention to use digital library. This has provided the
evidence of a moderating effect of experience in the intention to use
digital library. It is expected that this research will shed new lights
into research of acceptance and intention to use the library in a digital
environment.
Abstract: In this work, we present a comparison between two
techniques of image compression. In the first case, the image is
divided in blocks which are collected according to zig-zag scan. In
the second one, we apply the Fast Cosine Transform to the image,
and then the transformed image is divided in blocks which are
collected according to zig-zag scan too. Later, in both cases, the
Karhunen-Loève transform is applied to mentioned blocks. On the
other hand, we present three new metrics based on eigenvalues for a
better comparative evaluation of the techniques. Simulations show
that the combined version is the best, with minor Mean Absolute
Error (MAE) and Mean Squared Error (MSE), higher Peak Signal to
Noise Ratio (PSNR) and better image quality. Finally, new technique
was far superior to JPEG and JPEG2000.
Abstract: In this paper, a few chattering-free Sliding Mode Controllers (SMC) are proposed to stabilize an Active Magnetic Bearing (AMB) system with gyroscopic effect that is proportional to the rotor speed. The improved switching terms of the controller inherited from the saturation-type function and boundary layer control technique is shown to be able to achieve bounded and asymptotic stability, respectively, while the chattering effect in the input is attenuated. This is proven to be advantageous for AMB system since minimization of chattering results in optimized control effort. The performance of each controller is demonstrated via result of simulation in which the measurement of the total consumed energy and maximum control magnitude of each controller illustrates the effectiveness of the proposed controllers.
Abstract: This paper deals with a novel technique for the
fabrication of Spiral grooves in a dynamic thrust bearing. The main
scheme proposed in this paper is to fabricate the microgrooves using
desktop forming system. This process has advantages compared to the
conventional electro-chemical machining in the viewpoint of a higher
productivity. For this reason, a new testing apparatus is designed and
built for press forming microgrooves on a surface of the thrust bearing.
The material used in this study is sintered Cu-Fe alloy. The effects of
the forming load on the performance of micro press forming are
experimentally investigated. From the experimental results, formed
depths are closed to the target ones with increasing the forming load.
Abstract: Highly ordered TiO2 nanotube (TNT) arrays were
fabricated onto a pre-treated titanium foil by anodic oxidation with a
voltage of 20V in phosphoric acid/sodium fluoride electrolyte. A pretreatment
of titanium foil involved washing with acetone,
isopropanol, ethanol and deionized water. Carbon doped TiO2
nanotubes (C-TNT) was fabricated 'in-situ' with the same method in
the presence of polyvinyl alcohol and urea as carbon sources. The
affects of polyvinyl alcohol concentration and oxidation time on the
composition, morphology and structure of the C-TN were studied by
FE-SEM, EDX and XRD techniques. FESEM images of the
nanotubes showed uniform arrays of C-TNTs. The density and
microstructures of the nanotubes were greatly affected by the content
of PVA. The introduction of the polyvinyl alcohol into the electrolyte
increases the amount of C content inside TiO2 nanotube arrays
uniformly. The influence of carbon content on the photo-current of
C-TNT was investigated and the I-V profiles of the nanotubes were
established. The preliminary results indicated that the 'in-situ'
doping technique produced a superior quality nanotubes compared to
post doping techniques.
Abstract: The paper presents a novel idea to control computer
mouse cursor movement with human eyes. In this paper, a working
of the product has been described as to how it helps the special
people share their knowledge with the world. Number of traditional
techniques such as Head and Eye Movement Tracking Systems etc.
exist for cursor control by making use of image processing in which
light is the primary source. Electro-oculography (EOG) is a new
technology to sense eye signals with which the mouse cursor can be
controlled. The signals captured using sensors, are first amplified,
then noise is removed and then digitized, before being transferred to
PC for software interfacing.
Abstract: In modern era, the biggest challenge facing the
software industry is the upcoming of new technologies. So, the
software engineers are gearing up themselves to meet and manage
change in large software system. Also they find it difficult to deal
with software cognitive complexities. In the last few years many
metrics were proposed to measure the cognitive complexity of
software. This paper aims at a comprehensive survey of the metric of
software cognitive complexity. Some classic and efficient software
cognitive complexity metrics, such as Class Complexity (CC),
Weighted Class Complexity (WCC), Extended Weighted Class
Complexity (EWCC), Class Complexity due to Inheritance (CCI) and
Average Complexity of a program due to Inheritance (ACI), are
discussed and analyzed. The comparison and the relationship of these
metrics of software complexity are also presented.
Abstract: In this paper, Selective Adaptive Parallel Interference Cancellation (SA-PIC) technique is presented for Multicarrier Direct Sequence Code Division Multiple Access (MC DS-CDMA) scheme. The motivation of using SA-PIC is that it gives high performance and at the same time, reduces the computational complexity required to perform interference cancellation. An upper bound expression of the bit error rate (BER) for the SA-PIC under Rayleigh fading channel condition is derived. Moreover, the implementation complexities for SA-PIC and Adaptive Parallel Interference Cancellation (APIC) are discussed and compared. The performance of SA-PIC is investigated analytically and validated via computer simulations.
Abstract: The triumph of inductive neuro-stimulation since its rediscovery in the 1980s has been quite spectacular. In lots of branches ranging from clinical applications to basic research this system is absolutely indispensable. Nevertheless, the basic knowledge about the processes underlying the stimulation effect is still very rough and rarely refined in a quantitative way. This seems to be not only an inexcusable blank spot in biophysics and for stimulation prediction, but also a fundamental hindrance for technological progress. The already very sophisticated devices have reached a stage where further optimization requires better strategies than provided by simple linear membrane models of integrate-and-fire style. Addressing this problem for the first time, we suggest in the following text a way for virtual quantitative analysis of a stimulation system. Concomitantly, this ansatz seems to provide a route towards a better understanding by using nonlinear signal processing and taking the nerve as a filter that is adapted for neuronal magnetic stimulation. The model is compact and easy to adjust. The whole setup behaved very robustly during all performed tests. Exemplarily a recent innovative stimulator design known as cTMS is analyzed and dimensioned with this approach in the following. The results show hitherto unforeseen potentials.
Abstract: Deep cold rolling (DCR) and low plasticity burnishing (LPB) process are cold working processes, which easily produce a smooth and work-hardened surface by plastic deformation of surface irregularities. The present study focuses on the surface roughness and surface hardness aspects of AISI 4140 work material, using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in order to identify the predominant factors amongst the selected parameters. They were then categorized in order of significance followed by setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. In the present work, the influence of main process parameters (force, feed rate, number of tool passes/overruns, initial roughness of the work piece, ball material, ball diameter and lubricant used) on the surface roughness and the hardness of AISI 4140 steel were studied for both LPB and DCR process and the results are compared. It was observed that by using LPB process surface hardness has been improved by 167% and in DCR process surface hardness has been improved by 442%. It was also found that the force, ball diameter, number of tool passes and initial roughness of the workpiece are the most pronounced parameters, which has a significant effect on the work piece-s surface during deep cold rolling and low plasticity burnishing process.
Abstract: Compensating physiological motion in the context
of minimally invasive cardiac surgery has become an attractive
issue since it outperforms traditional cardiac procedures offering
remarkable benefits. Owing to space restrictions, computer vision
techniques have proven to be the most practical and suitable solution.
However, the lack of robustness and efficiency of existing methods
make physiological motion compensation an open and challenging
problem. This work focusses on increasing robustness and efficiency
via exploration of the classes of 1−and 2−regularized optimization,
emphasizing the use of explicit regularization. Both approaches are
based on natural features of the heart using intensity information.
Results pointed out the 1−regularized optimization class as the best
since it offered the shortest computational cost, the smallest average
error and it proved to work even under complex deformations.