Abstract: Calcium phosphate cement (CPC) is one of the most
attractive bioceramics due to its moldable and shape ability to fill
complicated bony cavities or small dental defect positions. In this
study, CPC was produced by using mixture of tetracalcium phosphate
(TTCP, Ca4O(PO4)2) and dicalcium phosphate anhydrous (DCPA,
CaHPO4) in equimolar ratio (1/1) with aqueous solutions of acetic
acid (C2H4O2) and disodium hydrogen phosphate dehydrate
(Na2HPO4.2H2O) in combination with sodium alginate in order to
improve theirs moldable characteristic. The concentration of the
aqueous solutions and sodium alginate were varied to investigate the
effect of different aqueous solutions and alginate on properties of the
cements. The cement paste was prepared by mixing cement powder
(P) with aqueous solution (L) in a P/L ratio of 1.0g/0.35ml. X-ray
diffraction (XRD) was used to analyses phase formation of the
cements. Setting time and compressive strength of the set CPCs were
measured using the Gilmore apparatus and Universal testing
machine, respectively.
The results showed that CPCs could be produced by using both
basic (Na2HPO4.2H2O) and acidic (C2H4O2) solutions. XRD results
show the precipitation of hydroxyapatite in all cement samples. No
change in phase formation among cements using difference
concentrations of Na2HPO4.2H2O solutions. With increasing
concentration of acidic solutions, samples obtained less
hydroxyapatite with a high dicalcium phosphate dehydrate leaded to
a shorter setting time. Samples with sodium alginate exhibited higher
crystallization of hydroxyapatite than that of without alginate as a
result of shorten setting time in a basic solution but a longer setting
time in an acidic solution. The stronger cement was attained from
samples using the acidic solution with sodium alginate; however the
strength was lower than that of using the basic solution.
Abstract: The main objective of the study is focused in
producing slag based geopolymer concrete obtained with the addition
of alkali activator. Test results indicated that the reaction of silicates
in slag is based on the reaction potential of sodium hydroxide and the
formation of alumino-silicates. The study also comprises on the
evaluation of the efficiency of polymer reaction in terms of the
strength gain properties for different geopolymer mixtures.
Geopolymer mixture proportions were designed for different binder
to total aggregate ratio (0.3 & 0.45) and fine to coarse aggregate ratio
(0.4 & 0.8). Geopolymer concrete specimens casted with normal
curing conditions reported a maximum 28 days compressive strength
of 54.75 MPa. The addition of glued steel fibres at 1.0% Vf in
geopolymer concrete showed reasonable improvements on the
compressive strength, split tensile strength and flexural properties of
different geopolymer mixtures. Further, comparative assessment was
made for different geopolymer mixtures and the reinforcing effects of
steel fibres were investigated in different concrete matrix.
Abstract: Heightened concerns over the amount of carbon
emitted from coal-related processes are generating shifts to the
application of biomass. In co-gasification, where coal is gasified
along with biomass, the biomass may be fed together with coal (cofeeding)
or an independent biomass gasifier needs to be integrated
with the coal gasifier. The main aim of this work is to evaluate the
biomass introduction methods in coal co-gasification. This includes
the evaluation of biomass concentration input (B0 to B100) and its
gasification performance. A process model is developed and
simulated in Aspen HYSYS, where both coal and biomass are
modelled according to its ultimate analysis. It was found that the
syngas produced increased with increasing biomass content for both
co-feeding and independent schemes. However, the heating values
and heat duties decreases with biomass concentration as more CO2
are produced from complete combustion.
Abstract: Since the marine environmental conditions are
extremely different from the other ones, marine actinomycetes might
produce novel bioactive compounds. Therefore, actinomycete strains
were screened from marine water and sediment samples collected
from the coastal areas of Northern Vietnam. Ninety-nine
actinomycete strains were obtained on starch-casein agar media by
dilution technique, only seven strains, named HP112, HP12, HP411,
HPN11, HP 11, HPT13 and HPX12, showed significant antibacterial
activity against both gram-positive and gram-negative bacteria
(Bacillus subtilis ATCC 6633, Staphylococcus epidemidis ATCC
12228, Escherichia coli ATCC 11105). Further studies were carried
out with the most active HP411 strain against Candida albicans
ATCC 10231. This strain could grow rapidly on starch casein agar
and other media with high salt containing 7-10% NaCl at 28-30oC.
Spore-chain of HP411 showed an elongated and circular shape with
10 to 30 spores/chain. Identification of the strain was carried out by
employing the taxonomical studies including the 16S rRNA
sequence. Based on phylogenetic and phenotypic evidence it is
proposed that HP411 to be belongs to species Streptomyces
variabilis. The potent of the crude extract of fermentation broth of
HP411 that are effective against wide range of pathogens: both grampositive,
gram-negative and fungi. Further studies revealed that the
crude extract HP411 could obtain the anticancer activity for cancer
cell lines: Hep-G2 (liver cancer cell line); RD (cardiac and skeletal
muscle letters cell line); FL (membrane of the uterus cancer cell line).
However, the actinomycetes from marine ecosystem will be useful
for the discovery of new drugs in the future.
Abstract: Climate warming would increase rainfall by shifting
precipitation falling form from snow to rain, and would accelerate
snow cover disappearing by increasing snowpack. Using temperature
and precipitation data in the temperature-index snowmelt model, we
evaluated variability of snowfall and continuous snow cover duration
(CSCD) during 1944-2010 over Pelso, central Finland. Mann-
Kendall non-parametric test determined that annual precipitation
increased by 2.69 (mm/year, p
Abstract: Climate change would cause mean sea level to rise +1
m by 2100. To prevent coastal floods resulting from the sea level
rising, different flood control structures have been built, with
acceptable protection levels. Gothenburg with the River Göta älv
located on the southwest coast of Sweden is a vulnerable city to the
accelerated rises in mean sea level. We evaluated using a sea barrage
in the River Göta älv to protect Gothenburg during this century. The
highest sea level was estimated to 2.95 m above the current mean sea
level by 2100. To verify flood protection against such high sea levels,
both barriers have to be closed. To prevent high water level in the
River Göta älv reservoir, the barriers would be open when the sea
level is low. The suggested flood control structures would
successfully protect the city from flooding events during this century.
Abstract: Food contamination occurs during post process
handling. This leads to spoilage and growth of pathogenic
microorganisms in the food, thereby reducing its shelf life or
spreading of food borne diseases. Several methods are tried and one
of which is use of antimicrobial packaging. Here, papain, a protease
enzyme, is covalently immobilized with the help of glutarldehyde on
polyurethane and used as a food wrap to protect food from microbial
contamination. Covalent immobilization of papain was achieved at a
pH of 7.4; temperature of 4°C; glutaraldehyde concentration of 0.5%;
incubation time of 24h; and 50mg of papain. The formation of -C=Nobserved
in the Fourier transform infrared spectrum confirmed the
immobilization of the enzyme on the polymer. Immobilized enzyme
retained higher activity than the native free enzyme. The modified
polyurethane showed better reduction of Staphylococcus aureus
biofilm than bare polymer film (eight folds reduction in live colonies,
two times reduction in protein and 6 times reduction in
carbohydrates). The efficacy of this was studied by wrapping it over
S. aureus contaminated cottage cheese (paneer) and cheese and
stored at a temperature of 4°C for 7days. The modified film reduced
the bacterial contamination by eight folds when compared to the bare
film. FTIR also indicated reduction in lipids, sugars and proteins in
the biofilm.
Abstract: Collapsible soils go through radical rearrangement of
their particles when triggered by water, stress or/and vibration,
causing loss of volume. This loss of volume in soil as seen in
foundation failures has caused millions of dollars’ worth of damages
to public facilities and infrastructure and so has an adverse effect on
the society and people. Despite these consequences and the several
studies that are available, more research is still required in the study
of soil collapsibility. Discerning the pedogenesis (formation) of soils
and investigating the combined effects of the different geological soil
properties is key to elucidating and quantifying soils collapsibility.
This study presents a novel laboratory testing regime that would be
undertaken on soil samples where the effects of soil type, compactive
variables (moisture content, density, void ratio, degree of saturation)
and loading are analyzed. It is anticipated that results obtained would
be useful in mapping the trend of the combined effect thus the basis
for evaluating soil collapsibility or collapse potentials encountered in
construction with volume loss problems attributed to collapse.
Abstract: South Africa has some regions which are susceptible
to moderate seismic activity. A peak ground acceleration of between
0.1g and 0.15g can be expected in the southern parts of the Western
Cape. Unreinforced Masonry (URM) is commonly used as a
construction material for 2 to 5 storey buildings in underprivileged
areas in and around Cape Town. URM is typically regarded as the
material most vulnerable to damage when subjected to earthquake
excitation. In this study, a three-storey URM building was analysed
by applying seven earthquake time-histories, which can be expected
to occur in South Africa using a finite element approach.
Experimental data was used to calibrate the in- and out-of-plane
stiffness of the URM. The results indicated that tensile cracking of
the in-plane piers was the dominant failure mode. It is concluded that
URM buildings of this type are at risk of failure especially if
sufficient ductility is not provided. The results also showed that
connection failure must be investigated further.
Abstract: Columns have traditionally been constructed of
reinforced concrete or structural steel. Much attention was allocated
to estimate the axial capacity of the traditional column sections to the
detriment of other forms of construction. Other forms of column
construction such as Concrete Filled Double Skin Tubes received
little research attention, and almost no attention when subjected to
eccentric loading. This paper investigates the axial capacity of
columns when subjected to eccentric loading. The experimental axial
capacities are compared to other established theoretical formulae on
concentric loading to determine a possible relationship. The study
found a good correlation between the reduction in axial capacity for
different column lengths and hollow section ratios.
Abstract: Preparation of nanoparticles of cerium oxide and
adsorption of bovine serum albumin on them were studied. Particle
size distribution and influence of pH on zeta potential of prepared
CeO2 were determined. Average size of prepared cerium oxide
nanoparticles was 9 nm. The simultaneous measurements of the
bovine serum albumin adsorption and zeta potential determination of
the (adsorption) suspensions were carried out. The adsorption
isotherms were found to be of typical Langmuir type; values of the
bovine serum albumin adsorption capacities were calculated.
Increasing of pH led to decrease of zeta potential and decrease of
adsorption capacity of cerium oxide nanoparticles. The maximum
adsorption capacity was found for strongly acid suspension (am =
118 mg/g). The samples of nanoceria with positive zeta potential
adsorbed more bovine serum albumin on the other hand, the samples
with negative zeta potential showed little or no protein adsorption.
Surface charge or better say zeta potential of CeO2 nanoparticles
plays the key role in adsorption of proteins on such type of materials.
Abstract: Pavement surface unevenness plays a pivotal role on
roughness index of road which affects on riding comfort ability.
Comfort ability refers to the degree of protection offered to vehicle
occupants from uneven elements in the road surface. So, it is
preferable to have a lower roughness index value for a better riding
quality of road users. Roughness is generally defined as an
expression of irregularities in the pavement surface which can be
measured using different equipments like MERLIN, Bump integrator,
Profilometer etc. Among them Bump Integrator is quite simple and
less time consuming in case of long road sections. A case study is
conducted on low volume roads in West District in Tripura to
determine roughness index (RI) using Bump Integrator at the
standard speed of 32 km/h. But it becomes too tough to maintain the
requisite standard speed throughout the road section. The speed of
Bump Integrator (BI) has to lower or higher in some distinctive
situations. So, it becomes necessary to convert these roughness index
values of other speeds to the standard speed of 32 km/h. This paper
highlights on that roughness index conversional model. Using SPSS
(Statistical Package of Social Sciences) software a generalized
equation is derived among the RI value at standard speed of 32 km/h
and RI value at other speed conditions.
Abstract: Electricity is recognized as fundamental to
industrialization and improving the quality of life of the people.
Harnessing the immense untapped hydropower potential in Tripura
region opens avenues for growth and provides an opportunity to
improve the well-being of the people of the region, while making
substantial contribution to the national economy. Gumti hydro power
plant generates power to mitigate the crisis of power in Tripura,
India. The first unit of hydro power plant (5MW) was commissioned
in June 1976 & another two units of 5 MW was commissioned
simultaneously. But out of 15MW capacity at present only 8MW-
9MW power is produced from Gumti hydro power plant during rainy
season. But during lean season the production reduces to 0.5MW due
to shortage of water. Now, it is essential to implement some
mitigation measures so that the further atrocities can be prevented
and originality will be possible to restore. The decision making
ability of the Analytic Hierarchy Process (AHP) and Concordance
Analysis Techniques (CAT) are utilized to identify the better decision
or solution to the present problem. Some related attributes are
identified by the method of surveying within the experts and the
available reports and literatures. Similar criteria are removed and
ultimately seven relevant ones are identified. All the attributes are
compared with each other and rated accordingly to their importance
over the other with the help of Pair wise Comparison Matrix. In the
present investigation different mitigation measures are identified and
compared to find the best suitable alternative which can solve the
present uncertainties involving the existence of the Gumti Hydro
Power Plant.
Abstract: Paper presents a study about dynamic effects obtained
from the dynamic load testing of the city highway bridges in Latvia
carried out from 2005 to 2012. 9 prestressed concrete bridges and 4
composite bridges were considered. 11 of 13 bridges were designed
according to the Eurocodes but two according to the previous
structural codes used in Latvia (SNIP 2.05.03-84). The dynamic
properties of the bridges were obtained by heavy vehicle passing the
bridge roadway with different driving speeds and with or without
even pavement. The obtained values of the Dynamic amplification
factor (DAF) and the bridge natural frequency were analyzed and
compared to the values of built-in traffic load models provided in
Eurocode 1. The actual DAF values for even bridge pavement in the
most cases are smaller than the value adopted in Eurocode 1. Vehicle
speed for uneven pavements significantly influence Dynamic
amplification factor values.
Abstract: The thermo-mechanical behaviour of concrete energy
pile foundations with different single and double U-tube shapes
incorporated was analysed using the Comsol Multi-physics package.
For the analysis, a 3D numerical model in real scale of the concrete
pile and surrounding soil was simulated regarding actual operation of
ground heat exchangers (GHE) and the surrounding ambient
temperature. Based on initial ground temperature profile measured in
situ, tube inlet temperature was considered to range from 6oC to 0oC
(during the contraction process) over a 30-day period. Extra thermal
stresses and deformations were calculated during the simulations and
differences arising from the use of two different systems (single-tube
and double-tube) were analysed. The results revealed no significant
difference for extra thermal stresses at the centre of the pile in either
system. However, displacements over the pile length were found to
be up to 1.5-fold higher in the double-tube system than the singletube
system.
Abstract: This paper discusses about the findings of preliminary
survey on MATLAB software learning among power electronics
students. One of the main focuses of power electronics course is on
DC to DC boost convertors, because boost convertors are generally
used in different industrial and non industrial applications. Population
samples of this study were randomly selected final year bachelor of
electronics and electrical engineering students from University Tun
Hussein Onn Malaysia (UTHM).As per the results from the survey
questioner analysis, almost eighty percent students are facing
problem and difficulties in Dc to Dc boost convertors experimental
understanding without using MATLAB simulink package. As per
finding of this study it is clear that MATLAB play an effective and
efficient function for better understanding of boost convertors
experimental work among power electronics learners.
Abstract: In this paper, we propose a new packing strategy to
find a free resource for run-time mapping of application tasks to
NoC-based Heterogeneous MPSoC. The proposed strategy minimizes
the task mapping time in addition to placing the communicating tasks
close to each other. To evaluate our approach, a comparative study is
carried out for a platform containing single task supported PEs.
Experiments show that our strategy provides better results when
compared to latest dynamic mapping strategies reported in the
literature.
Abstract: There are pending discussions over the mapping of
country export potential in order to refocus export strategy of firms
and its evidence-based promotion by the Export Credit Agencies
(ECAs) and other permitted vehicles of governments.
In this paper we develop our version of an applied model that
offers “stepwise” elimination of unattractive markets. We modify and
calibrate the model for the particular features of the Czech Republic
and specific pilot cases where we apply an individual approach to
each sector.
Abstract: A computational fluid dynamics simulation is done for
non-Newtonian fluid in a baffled stirred tank. The CMC solution is
taken as non-Newtonian shear thinning fluid for simulation. The
Reynolds Average Navier Stocks equation with steady state multi
reference frame approach is used to simulate flow in the stirred tank.
The turbulent flow field is modelled using realizable k-ε turbulence
model. The simulated velocity profiles of Rushton turbine is
validated with literature data. Then, the simulated flow field of CD-6
impeller is compared with the Rushton turbine. The flow field
generated by CD-6 impeller is less in magnitude than the Rushton
turbine. The impeller global parameter, power number and flow
number, and entropy generation due to viscous dissipation rate is also
reported.
Abstract: Curcuma longa L. (Zingiberaceae), commonly known
as turmeric, has a long history of traditional uses for culinary
purposes as a spice and a food colorant. The present study aimed to
document the ethnobotanical knowledge about Curcuma longa, and
to assess the variation in the herbalists’ experience in Northeastern
Algeria. Data were collected using semi-structured questionnaires
and direct interviews with 30 herbalists. Ethnobotanical indices,
including the fidelity level (FL%), the relative frequency citation
(RFC), and use value (UV) were determined by quantitative methods.
Diversity in the level of knowledge was analyzed using univariate,
non-parametric, and multivariate statistical methods. Three main
categories of uses were recorded for C. longa: for food, for medicine,
and for cosmetic purposes. As a medicine, turmeric was used for the
treatment of gastrointestinal, dermatological, and hepatic diseases.
Medicinal and food uses were correlated with both forms of
preparation (rhizome and powder). The age group did not influence
the use. Multivariate analyses showed a significant variation in
traditional knowledge, associated with the use value, origin, quality,
and efficacy of the drug. The findings suggested that the geographical
origin of C. longa affected the use in Algeria.