Abstract: The Wind Turbine Modeling in Wind Energy Conversion System (WECS) using Doubly-Fed Induction Generator (DFIG) PI Controller based design is presented. To study about the variable wind speed. The PI controller performs responding to the dynamic performance. The objective is to study the characteristic of wind turbine and finding the optimum wind speed suitable for wind turbine performance. This system will allow the specification setting (2.5MW). The output active power also corresponding same the input is given. And the reactive power produced by the wind turbine is regulated at 0 Mvar. Variable wind speed is optimum for drive train performance at 12.5 m/s (at maximum power coefficient point) from the simulation of DFIG by Simulink is described.
Abstract: In this work, we suggested a new approach for the
control of a mobile robot capable of being a building block of an
intelligent agent. This approach includes obstacle avoidance and goal
tracking implemented as two different sliding mode controllers. A
geometry based behavior arbitration is proposed for fusing the two
outputs. Proposed structure is tested on simulations and real robot.
Results have confirmed the high performance of the method.
Abstract: Matching algorithms have significant importance in
speaker recognition. Feature vectors of the unknown utterance are
compared to feature vectors of the modeled speakers as a last step in
speaker recognition. A similarity score is found for every model in
the speaker database. Depending on the type of speaker recognition,
these scores are used to determine the author of unknown speech
samples. For speaker verification, similarity score is tested against a
predefined threshold and either acceptance or rejection result is
obtained. In the case of speaker identification, the result depends on
whether the identification is open set or closed set. In closed set
identification, the model that yields the best similarity score is
accepted. In open set identification, the best score is tested against a
threshold, so there is one more possible output satisfying the
condition that the speaker is not one of the registered speakers in
existing database. This paper focuses on closed set speaker
identification using a modified version of a well known matching
algorithm. The results of new matching algorithm indicated better
performance on YOHO international speaker recognition database.
Abstract: In this paper, a Gaussian multiple input multiple output multiple eavesdropper (MIMOME) channel is considered where a transmitter communicates to a receiver in the presence of an eavesdropper. We present a technique for determining the secrecy capacity of the multiple input multiple output (MIMO) channel under Gaussian noise. We transform the degraded MIMOME channel into multiple single input multiple output (SIMO) Gaussian wire-tap channels and then use scalar approach to convert it into two equivalent multiple input single output (MISO) channels. The secrecy capacity model is then developed for the condition where the channel state information (CSI) for main channel only is known to the transmitter. The results show that the secret communication is possible when the eavesdropper channel noise is greater than a cutoff noise level. The outage probability is also analyzed of secrecy capacity is also analyzed. The effect of fading and outage probability is also analyzed.
Abstract: Small and Medium Sized Enterprises (SMEs) play an important role in many economies. In New Zealand, for example, 97% of all manufacturing companies employ less than 100 staff, and generate the predominant part of this industry sector-s economic output. Manufacturing SMEs as a group also have a significant impact on the environment. This situation is similar in many developed economies, including the European Union. Sustainable economic development therefore needs to strongly consider the role of manufacturing SMEs, who generally find it challenging to move towards more environmentally friendly business practices. This paper presents a systems thinking approach to modelling and understanding the factors which have an influence on the successful uptake of environmental practices in small and medium sized manufacturing companies. It presents a number of causal loop diagrams which have been developed based on primary action research, and a thorough understanding of the literature in this area. The systems thinking model provides the basis for further development of a strategic framework for the successful uptake of environmental innovation in manufacturing SMEs.
Abstract: The objective of this paper is to develop a neural
network-based residual generator to detect the fault in the actuators
for a specific communication satellite in its attitude control system
(ACS). First, a dynamic multilayer perceptron network with dynamic
neurons is used, those neurons correspond a second order linear
Infinite Impulse Response (IIR) filter and a nonlinear activation
function with adjustable parameters. Second, the parameters from the
network are adjusted to minimize a performance index specified by
the output estimated error, with the given input-output data collected
from the specific ACS. Then, the proposed dynamic neural network
is trained and applied for detecting the faults injected to the wheel,
which is the main actuator in the normal mode for the communication
satellite. Then the performance and capabilities of the proposed
network were tested and compared with a conventional model-based
observer residual, showing the differences between these two
methods, and indicating the benefit of the proposed algorithm to
know the real status of the momentum wheel. Finally, the application
of the methods in a satellite ground station is discussed.
Abstract: This paper explains the development of Multifunctional Barcode Inventory Management System (MBIMS) to manage inventory and stock ordering. Today, most of the retailing market is still manually record their stocks and its effectiveness is quite low. By providing MBIMS, it will bring effectiveness to retailing market in inventory management. MBIMS will not only save time in recording input, output and refilling the inventory stock, but also in calculating remaining stock and provide auto-ordering function. This system is developed through System Development Life Cycle (SDLC) and the flow and structure of the system is fully built based on requirements of a retailing market. Furthermore, this system has been developed from methodical research and study where each part of the system is vigilantly designed. Thus, MBIMS will offer a good solution to the retailing market in achieving effectiveness and efficiency in inventory management.
Abstract: Fuel cells have become one of the major areas of
research in the academia and the industry. The goal of most fish
farmers is to maximize production and profits while holding labor
and management efforts to the minimum. Risk of fish kills, disease
outbreaks, poor water quality in most pond culture operations,
aeration offers the most immediate and practical solution to water
quality problems encountered at higher stocking and feeding rates.
Many units of aeration system are electrical units so using a
continuous, high reliability, affordable, and environmentally friendly
power sources is necessary. Aeration of water by using PEM fuel cell
power is not only a new application of the renewable energy, but
also, it provides an affordable method to promote biodiversity in
stagnant ponds and lakes. This paper presents a new design and
control of PEM fuel cell powered a diffused air aeration system for a
shrimp farm in Mersa Matruh in Egypt. Also Artificial intelligence
(AI) techniques control is used to control the fuel cell output power
by control input gases flow rate. Moreover the mathematical
modeling and simulation of PEM fuel cell is introduced. A
comparison study is applied between the performance of fuzzy logic
control (FLC) and neural network control (NNC). The results show
the effectiveness of NNC over FLC.
Abstract: Linear induction motors are used in various industries
but they have some specific phenomena which are the causes for
some problems. The most important phenomenon is called end effect.
End effect decreases efficiency, power factor and output force and
unbalances the phase currents. This phenomenon is more important
in medium and high speeds machines. In this paper a factor, EEF , is
obtained by an accurate equivalent circuit model, to determine the
end effect intensity. In this way, all of effective design parameters on
end effect is described. Accuracy of this equivalent circuit model is
evaluated by two dimensional finite-element analysis using ANSYS.
The results show the accuracy of the equivalent circuit model.
Abstract: Internet Access Technologies (IAT) provide a means
through which Internet can be accessed. The choice of a suitable
Internet technology is increasingly becoming an important issue to
ISP clients. Currently, the choice of IAT is based on discretion and
intuition of the concerned managers and the reliance on ISPs. In this
paper we propose a model and designs algorithms that are used in the
Internet access technology specification. In the proposed model, three
ranking approaches are introduced; concurrent ranking, stepwise
ranking and weighted ranking. The model ranks the IAT based on
distance measures computed in ascending order while the global
ranking system assigns weights to each IAT according to the position
held in each ranking technique, determines the total weight of a
particular IAT and ranks them in descending order. The final output
is an objective ranking of IAT in descending order.
Abstract: A simple analytical model has been developed to
optimize biasing conditions for obtaining maximum linearity among
lattice-matched, pseudomorphic and metamorphic HEMT types as
well as enhancement and depletion HEMT modes. A nonlinear
current-voltage model has been simulated based on extracted data to
study and select the most appropriate type and mode of HEMT in
terms of a given gate-source biasing voltage within the device so as
to employ the circuit for the highest possible output current or
voltage linear swing. Simulation results can be used as a basis for the
selection of optimum gate-source biasing voltage for a given type
and mode of HEMT with regard to a circuit design. The
consequences can also be a criterion for choosing the optimum type
or mode of HEMT for a predetermined biasing condition.
Abstract: This paper presents a method of reducing the feedback
delay time of DWA(Data Weighted Averaging) used in sigma-delta
modulators. The delay time reduction results from the elimination of
the latch at the quantizer output and also from the falling edge
operation. The designed sigma-delta modulator improves the timing
margin about 16%. The sub-circuits of sigma-delta modulator such as
SC(Switched Capacitor) integrator, 9-level quantizer, comparator, and
DWA are designed with the non-ideal characteristics taken into
account. The sigma-delta modulator has a maximum SNR (Signal to
Noise Ratio) of 84 dB or 13 bit resolution.
Abstract: This article deals with the numerical simulation of the
floor heating convector in 3D. Presented convector can operate in
two modes – cooling mode and heating mode. This initial numerical
simulation is focused on cooling mode of the convector. Models with
different temperature of the fins are compared and three various
shapes of the fins are examined as well. The objective of the work is
to predict air flow and heat transfer inside convector for further
optimalization of these devices. For the numerical simulation was
used commercial software Ansys Fluent.
Abstract: Selecting the word translation from a set of target
language words, one that conveys the correct sense of source word
and makes more fluent target language output, is one of core
problems in machine translation. In this paper we compare the 3
methods of estimating word translation probabilities for selecting the
translation word in Thai – English Machine Translation. The 3
methods are (1) Method based on frequency of word translation, (2)
Method based on collocation of word translation, and (3) Method
based on Expectation Maximization (EM) algorithm. For evaluation
we used Thai – English parallel sentences generated by NECTEC.
The method based on EM algorithm is the best method in comparison
to the other methods and gives the satisfying results.
Abstract: Software reuse can be considered as the most realistic
and promising way to improve software engineering productivity and
quality. Automated assistance for software reuse involves the
representation, classification, retrieval and adaptation of components.
The representation and retrieval of components are important to
software reuse in Component-Based on Software Development
(CBSD). However, current industrial component models mainly focus
on the implement techniques and ignore the semantic information
about component, so it is difficult to retrieve the components that
satisfy user-s requirements. This paper presents a method of business
component retrieval based on specification matching to solve the
software reuse of enterprise information system. First, a business
component model oriented reuse is proposed. In our model, the
business data type is represented as sign data type based on XML,
which can express the variable business data type that can describe the
variety of business operations. Based on this model, we propose
specification match relationships in two levels: business operation
level and business component level. In business operation level, we
use input business data types, output business data types and the
taxonomy of business operations evaluate the similarity between
business operations. In the business component level, we propose five
specification matches between business components. To retrieval
reusable business components, we propose the measure of similarity
degrees to calculate the similarities between business components.
Finally, a business component retrieval command like SQL is
proposed to help user to retrieve approximate business components
from component repository.
Abstract: In this paper, half bridge DC-DC converters with
transformer isolation presented in the literature are analyzed for highcurrent
and low-voltage applications under the same operation
conditions, and compared in terms of losses and efficiency. The
conventional and improved half-bridge DC-DC converters are
simulated, and current and voltage waveforms are obtained for input
voltage Vdc=500V, output current IO=450A, output voltage VO=38V
and switching frequency fS=20kHz. IGBTs are used as power
semiconductor switches. The power losses of the semiconductor
devices are calculated from current and voltage waveforms. From
simulation results, it is seen that the capacitor switched half bridge
converter has the best efficiency value, and can be preferred at high
power and high frequency applications.
Abstract: When a small H/W IP is designed, we can develop an
appropriate verification environment by observing the simulated
signal waves, or using the serial test vectors for the fixed output. In the
case of design and verification of a massive parallel processor with
multiple IPs, it-s difficult to make a verification system with existing
common verification environment, and to verify each partial IP. A
TestDrive verification environment can build easy and reliable
verification system that can produce highly intuitive results by
applying Modelsim and SystemVerilog-s DPI. It shows many
advantages, for example a high-level design of a GPGPU processor
design can be migrate to FPGA board immediately.
Abstract: Resource discovery is one of the chief services of a grid. A new approach to discover the provenances in grid through learning automata has been propounded in this article. The objective of the aforementioned resource-discovery service is to select the resource based upon the user-s applications and the mercantile yardsticks that is to say opting for an originator which can accomplish the user-s tasks in the most economic manner. This novel service is submitted in two phases. We proffered an applicationbased categorization by means of an intelligent nerve-prone plexus. The user in question sets his or her application as the input vector of the nerve-prone nexus. The output vector of the aforesaid network limns the appropriateness of any one of the resource for the presented executive procedure. The most scrimping option out of those put forward in the previous stage which can be coped with to fulfill the task in question is picked out. Te resource choice is carried out by means of the presented algorithm based upon the learning automata.
Abstract: A prototype of an anomaly detection system was
developed to automate process of recognizing an anomaly of
roentgen image by utilizing fuzzy histogram hyperbolization image
enhancement and back propagation artificial neural network.
The system consists of image acquisition, pre-processor, feature
extractor, response selector and output. Fuzzy Histogram
Hyperbolization is chosen to improve the quality of the roentgen
image. The fuzzy histogram hyperbolization steps consist of
fuzzyfication, modification of values of membership functions and
defuzzyfication. Image features are extracted after the the quality of
the image is improved. The extracted image features are input to the
artificial neural network for detecting anomaly. The number of nodes
in the proposed ANN layers was made small.
Experimental results indicate that the fuzzy histogram
hyperbolization method can be used to improve the quality of the
image. The system is capable to detect the anomaly in the roentgen
image.
Abstract: In this paper back-propagation artificial neural network
(BPANN )with Levenberg–Marquardt algorithm is employed to
predict the deformation of the upsetting process. To prepare a
training set for BPANN, some finite element simulations were
carried out. The input data for the artificial neural network are a set
of parameters generated randomly (aspect ratio d/h, material
properties, temperature and coefficient of friction). The output data
are the coefficient of polynomial that fitted on barreling curves.
Neural network was trained using barreling curves generated by
finite element simulations of the upsetting and the corresponding
material parameters. This technique was tested for three different
specimens and can be successfully employed to predict the
deformation of the upsetting process