Abstract: The design of a landing gear is one of the fundamental aspects of aircraft design. The need for a light weight, high strength, and stiffness characteristics coupled with techno economic feasibility are a key to the acceptability of any landing gear construction. In this paper, an approach for analyzing two different designed landing gears for an unmanned aircraft vehicle (UAV) using advanced CAE techniques will be applied. Different landing conditions have been considered for both models. The maximum principle stresses for each model along with the factor of safety are calculated for every loading condition. A conclusion is drawing about better geometry.
Abstract: Supplement use is common in athletes. Besides their cost, they may have side effects on health and performance. 250 questionnaires were distributed among female athletes (mean age 27.08 years). The questionnaire aimed to explore the frequency, type, believes, attitudes and knowledge regarding dietary supplements. Knowledge was good in 30.3%, fair in 60.2%, and poor in 9.1% of respondents. 65.3% of athletes did not use supplements regularly. The most widely used supplements were vitamins (48.4%), minerals (42.9%), energy supplements (21.3%), and herbals (20.9%). 68.9% of athletes believed in their efficacy. 34.4% experienced performance enhancement and 6.8% of reported side effects. 68.2% reported little knowledge and 60.9% were eager to learn more. In conclusion, many of the female athletes believe in the efficacy of supplements and think they are an unavoidable part of competitive sports. However, their information is not sufficient. We have to stress on education, consulting sessions, and rational prescription.
Abstract: This study sought to uncover the complex role of
stress in the workplace by investigating both positive (eustress) and
negative (distress) stress responses. In particular, the study tested a
mediation model in which organisational stressors (person-job fit and
role overload) influence employee affective wellbeing, both directly
and indirectly through stress responses. Participants were recruited
from retail and finance organisations in Australia and New Zealand,
and asked to complete an anonymous online questionnaire. A total of
140 individuals returned completed questionnaires. The results show
that person-job fit influenced eustress, which in turn had a positive
effect on employee affective wellbeing; and role overload impacted
distress, which in turn held a negative influence on affective
wellbeing. These findings indicate that different organisational
stressors have unique relationships with eustress and distress
responses. Limitations and implications of the study are discussed.
Abstract: An experimental study is presented on the effect
of microstructural change on the Portevin-Le Chatelier effect
behaviour of Al-2.5%Mg alloy. Tensile tests are performed on
the as received and heat treated (at 400 ºC for 16 hours)
samples for a wide range of strain rates. The serrations
observed in the stress-time curve are investigated from
statistical analysis point of view. Microstructures of the
samples are characterized by optical metallography and X-ray
diffraction. It is found that the excess vacancy generated due
to heat treatment leads to decrease in the strain rate sensitivity
and the increase in the number of stress drop occurrences per
unit time during the PLC effect. The microstructural
parameters like domain size, dislocation density have no
appreciable effect on the PLC effect as far as the statistical
behavior of the serrations is considered.
Abstract: Springback is a significant problem in the sheet metal
forming process. When the tools are released after the stage of
forming, the product springs out, because of the action of the internal
stresses. In many cases the deviation of form is too large and the
compensation of the springback is necessary. The precise prediction
of the springback of product is increasingly significant for the design
of the tools and for compensation because of the higher ratio of the
yield stress to the elastic modulus.
The main object in this paper was to study the effect of the
anisotropy on the springback for three directions of rolling: 0°, 45°
and 90°. At the same time, we highlighted the influence of three
different metallic materials: Aluminum, Steel and Galvanized steel.
The original of our purpose consist on tests which are ensured by
adapting a U-type stretching-bending device on a tensile testing
machine, where we studied and quantified the variation of the
springback according to the direction of rolling. We also showed the
role of lubrication in the reduction of the springback.
Moreover, in this work, we have studied important characteristics
in deep drawing process which is a springback. We have presented
defaults that are showed in this process and many parameters
influenced a springback.
Finally, our results works lead us to understand the influence of
grains orientation with different metallic materials on the springback
and drawing some conclusions how to concept deep drawing tools. In
addition, the conducted work represents a fundamental contribution
in the discussion the industry application.
Abstract: Oxidative stress and overwhelming free radicals
associated with diabetes mellitus are likely to be linked with
development of certain complication such as retinopathy,
nephropathy and neuropathy. Treatment of diabetic subjects with
antioxidant may be of advantage in attenuating these complications.
Olive leaf (Oleaeuropaea), has been endowed with many beneficial
and health promoting properties mostly linked to its antioxidant
activity. This study aimed to evaluate the significance of
supplementation of Olive leaves extract (OLE) in reducing oxidative
stress, hyperglycemia and hyperlipidemia in Sterptozotocin (STZ)-
induced diabetic rats. After induction of diabetes, a significant rise in
plasma glucose, lipid profiles except High density lipoproteincholestrol
(HDLc), malondialdehyde (MDA) and significant decrease
of plasma insulin, HDLc and Plasma reduced glutathione GSH as
well as alteration in enzymatic antioxidants was observed in all
diabetic animals. During treatment of diabetic rats with 0.5g/kg body
weight of Olive leaves extract (OLE) the levels of plasma (MDA)
,(GSH), insulin, lipid profiles along with blood glucose and
erythrocyte enzymatic antioxidant enzymes were significantly
restored to establish values that were not different from normal
control rats. Untreated diabetic rats on the other hand demonstrated
persistent alterations in the oxidative stress marker (MDA), blood
glucose, insulin, lipid profiles and the antioxidant parameters. These
results demonstrate that OLE may be of advantage in inhibiting
hyperglycemia, hyperlipidemia and oxidative stress induced by
diabetes and suggest that administration of OLE may be helpful in
the prevention or at least reduced of diabetic complications
associated with oxidative stress.
Abstract: Use of a sliding joint is an effective method to
decrease the stress in foundation structure where there is a horizontal
deformation of subsoil (areas afflicted with underground mining) or
horizontal deformation of a foundation structure (pre-stressed
foundations, creep, shrinkage, temperature deformation). A
convenient material for a sliding joint is a bitumen asphalt belt.
Experiments for different types of bitumen belts were undertaken at
the Faculty of Civil Engineering - VSB Technical University of
Ostrava in 2008. This year an extension of the 2008 experiments is in
progress and the shear resistance of a slide joint is being tested as a
function of temperature in a temperature controlled room. In this
paper experimental results of temperature dependant shear resistance
are presented. The result of the experiments should be the sliding
joint shear resistance as a function of deformation velocity and
temperature. This relationship is used for numerical analysis of
stress/strain relation between foundation structure and subsoil. Using
a rheological slide joint could lead to a decrease of the reinforcement
amount, and contribute to higher reliability of foundation structure
and thus enable design of more durable and sustainable building
structures.
Abstract: True stress-strain curve of railhead steel is required to
investigate the behaviour of railhead under wheel loading through elasto-plastic Finite Element (FE) analysis. To reduce the rate of wear, the railhead material is hardened through annealing and
quenching. The Australian standard rail sections are not fully hardened and hence suffer from non-uniform distribution of the
material property; usage of average properties in the FE modelling can potentially induce error in the predicted plastic strains. Coupons
obtained at varying depths of the railhead were, therefore, tested under axial tension and the strains were measured using strain gauges as well as an image analysis technique, known as the Particle Image Velocimetry (PIV). The head hardened steel exhibit existence of three distinct zones of yield strength; the yield strength as the ratio of the average yield strength provided in the standard (σyr=780MPa) and
the corresponding depth as the ratio of the head hardened zone along
the axis of symmetry are as follows: (1.17 σyr, 20%), (1.06 σyr, 20%-80%) and (0.71 σyr, > 80%). The stress-strain curves exhibit limited plastic zone with fracture occurring at strain less than 0.1.
Abstract: The experimental design was 4 x 5 factorial with three
replications in fully controlled research greenhouse in Department of
Soil Sciences and Plant Nutrition, Faculty of Agriculture, University
of Selcuk in the year of 2009. Determination of tolerant chickpea
genotypes to drought was made in the research. Additionally,
sophisticated effects of drought on plant growth and development,
biochemical and physical properties or physical defense mechanisms
were presented. According to the results, the primary genotypes were
Ilgın YP (0.0063 g/gh) for leaf water capacity, 22235 70.44(%) for
relative water content, 22159 (82.47%) for real water content,
22159 (5.03 mg/l) for chlorophyll a+b, Ilgın YP (125.89 nmol
H2O2.dak-1/ mg protein-1) for peroxidase, Yunak YP (769.67
unit/ mg protein-1) for superoxide dismutase, Seydişehir YP
(16.74 μg.TA-1) for proline, Gökçe (80.01 nmol H2O2.dak-1/ mg
protein-1) for catalase. Consequently, all the genotypes
increased their enzyme activity depending on the increasing of
drought stress consider with the effects of drought stress on leaf
enzyme activity. Chickpea genotypes are increasing enzyme
activity against to drought stress.
Abstract: Aerospace vehicles are subjected to non-uniform
thermal loading that may cause thermal buckling. A study was
conducted on the thermal post-buckling of shape memory alloy
composite plates subjected to the non-uniform tent-like temperature
field. The shape memory alloy wires were embedded within the
laminated composite plates to add recovery stress to the plates. The
non-linear finite element model that considered the recovery stress of
the shape memory alloy and temperature dependent properties of the
shape memory alloy and composite matrix along with its source
codes were developed. It was found that the post-buckling paths of
the shape memory alloy composite plates subjected to various tentlike
temperature fields were stable within the studied temperature
range. The addition of shape memory alloy wires to the composite
plates was found to significantly improve the post-buckling behavior
of laminated composite plates under non-uniform temperature
distribution.
Abstract: The effect of autofrettage process in strain hardened
thick-walled pressure vessels has been investigated theoretically by
finite element modeling. Equivalent von Mises stress is used as yield
criterion to evaluate the optimum autofrettage pressure and the
optimum radius of elastic-plastic junction. It has been observed that
the optimum autofrettage pressure increases along with the working
pressure. For two different working pressures, the effect of the ratio
of outer to inner radius (b/a=k) value on the optimum autofrettage
pressure is also noticed. The Optimum autofrettage pressure solely
depends on K value rather than on the inner or outer radius.
Furthermore, percentage reduction of von Mises stresses is compared
for different working pressures and different k values. Maximum von
Mises stress developed at different autofrettage pressure is equated
for elastic perfectly plastic and elastic-plastic material with different
slope of strain hardening segment. Cylinder material having higher
slope of strain hardening segment provides better benedictions in the
autofrettage process.
Abstract: The complex shape of the human pelvic bone was
successfully imaged and modeled using finite element FE processing.
The bone was subjected to quasi-static and dynamic loading
conditions simulating the effect of both weight gain and impact.
Loads varying between 500 – 2500 N (~50 – 250 Kg of weight) was
used to simulate 3D quasi-static weight gain. Two different 3D
dynamic analyses, body free fall at two different heights (1 and 2 m)
and forced side impact at two different velocities (20 and 40 Km/hr)
were also studied. The computed resulted stresses were compared for
the four loading cases, where Von Misses stresses increases linearly
with the weight gain increase under quasi-static loading. For the
dynamic models, the Von Misses stress history behaviors were
studied for the affected area and effected load with respect to time.
The normalization Von Misses stresses with respect to the applied
load were used for comparing the free fall and the forced impact load
results. It was found that under the forced impact loading condition
an over lapping behavior was noticed, where as for the free fall the
normalized Von Misses stresses behavior was found to nonlinearly
different. This phenomenon was explained through the energy
dissipation concept. This study will help designers in different
specialization in defining the weakest spots for designing different
supporting systems.
Abstract: One of the biggest problems of SMEs is their tendencies to financial distress because of insufficient finance background. In this study, an Early Warning System (EWS) model based on data mining for financial risk detection is presented. CHAID algorithm has been used for development of the EWS. Developed EWS can be served like a tailor made financial advisor in decision making process of the firms with its automated nature to the ones who have inadequate financial background. Besides, an application of the model implemented which covered 7,853 SMEs based on Turkish Central Bank (TCB) 2007 data. By using EWS model, 31 risk profiles, 15 risk indicators, 2 early warning signals, and 4 financial road maps has been determined for financial risk mitigation.
Abstract: Cabbage seedlings grown in vitro were exposed to
excess levels of heavy metals, including Cd, Mo, and Zn. High metal
levels affected plant growth at cotyledonary stage. Seedlings under
Cd, Mo, and Zn treatments could not produce root hairs and true
leaves. Under stress conditions, seedlings accumulated a higher
amount of anthocyanins in their cotyledons than those in the control.
The pigments isolated from Cd and Zn stressed seedling cotyledons
appeared as pink, while under Mo stress, was dark pink or purple.
Moreover, excess Mo stress increased antioxidant enzyme activities
of APX, CAT, SOD. These results suggest that, under excess Mo
stress, the induced antioxidant enzyme activity of cabbage seedlings
may function as a protective mechanism to shield the plants from
toxicity and exacerbated growth.
Abstract: The aim of this paper is to confirm the effect of key
design parameters, the punch radius and punch angle, on rupture of the
expansion tube using a finite element analysis with a ductile damage
model. The results of the finite element analysis indicated that the
expansion ratio of the tube was mainly affected by the radius of the
punch. However, the rupture was more affected by the punch angle
than the radius of the punch. The existence of a specific punch angle,
at which rupture did not occur, even if the radius of the punch was
increased, was found.
Abstract: Production of hard-to-cut materials with uncoated carbide cutting tools in turning, not only cause tool life reduction but also, impairs the product surface roughness. In this paper, influence of hot machining method were studied and presented in two cases. Case1-Workpiece surface roughness quality with constant cutting parameter and 300 ºC initial workpiece surface temperature. Case 2- Tool temperature variation when cutting with two speeds 78.5 (m/min) and 51 (m/min). The workpiece material and tool used in this study were AISI 1060 steel (45HRC) and uncoated carbide TNNM 120408-SP10(SANDVIK Coromant) respectively. A gas flam heating source was used to preheating of the workpiece surface up to 300 ºC, causing reduction of yield stress about 15%. Results obtained experimentally, show that the method used can considerably improved surface quality of the workpiece.
Abstract: In the past, there were many bridge-s collapses due to
lack of bridge structural capacity information. Most of concrete
bridge health was relied on information from visual inspection, which
sometime was inadequate. This study was conducted in order to
investigate relationship between bridge structural condition and
bridge visual condition. This study was a part of a big project
conducted at Department of Highways of Thailand. In this study, 31
bridges including slab-type bridges, plank-girder bridges, prestressed
box-beam bridges, prestressed I-girder bridges and prestressed multibeam
bridges were selected for visual inspection and load test. It was
found a positive correlation between bridge appearance and bridge-s
load carrying capacity. However, statistical characteristic revealed
low correlation between them.
Abstract: Constant amplitude fatigue crack growth (FCG) tests
were performed on dissimilar metal welded plates of Type 316L
Stainless Steel (SS) and IS 2062 Grade A Carbon steel (CS). The
plates were welded by TIG welding using SS E309 as electrode. FCG
tests were carried on the Side Edge Notch Tension (SENT)
specimens of 5 mm thickness, with crack initiator (notch) at base
metal region (BM), weld metal region (WM) and heat affected zones
(HAZ). The tests were performed at a test frequency of 10 Hz and at
load ratios (R) of 0.1 & 0.6. FCG rate was found to increase with
stress ratio for weld metals and base metals, where as in case of
HAZ, FCG rates were almost equal at high ΔK. FCG rate of HAZ of
stainless steel was found to be lowest at low and high ΔK. At
intermediate ΔK, WM showed the lowest FCG rate. CS showed
higher crack growth rate at all ΔK. However, the scatter band of data
was found to be narrow. Fracture toughness (Kc) was found to vary
in different locations of weldments. Kc was found lowest for the
weldment and highest for HAZ of stainless steel. A novel method of
characterizing the FCG behavior using an Infrared thermography
(IRT) camera was attempted. By monitoring the temperature rise at
the fast moving crack tip region, the amount of plastic deformation
was estimated.
Abstract: In the present paper, Fatigue life assessment of an
anti-roll bar component of a passenger vehicle, is investigated by
ANSYS 11 software. A stress analysis is also carried out by the
finite element technique for the determination of highly stressed
regions on the bar. Anti-roll bar is a suspension element used at the
front, rear, or at both ends of a car that reduces body roll by resisting
any unequal vertical motion between the pair of wheels to which it is
connected. As a first stage, fatigue damage models proposed by some
well-known references and the corresponding assumptions are
discussed and some enhancements are proposed. Then, fracture
analysis of an anti-roll bar of an automobile is carried out. The
analysed type of the anti-roll bar is especially important as many
cases are reported about the fracture after a 100,000 km of travel
fatigue and fracture conditions. This paper demonstrates fatigue life
of an anti-roll bar and then evaluated by experimental analytically
results from other researcher.
Abstract: With the advent of new technologies, factors related to
mental health in e-workspaces are taken into consideration more than
ever. Studies have revealed that one of the factors affecting the
productivity of employees in an organization is occupational stress.
Another influential factor is quality of work life which is important in
the improvement of work environment conditions and organizational
efficiency. In order to uncover the quality of work life level and to
investigate the impact of occupational stress on quality of work life
among information technology employees in Iran, a cross-sectional
study design was applied and data were gathered using a
questionnaire validated by a group of experts. The results of the study
showed that information technology staffs have average level of both
occupational stress and quality of work life. Furthermore, it was
found that occupational stress has a negative impact on quality of
work life. In addition, the same results were observed for role
ambiguity, role conflict, role under-load, work-pace, work
repetitiveness and tension toward quality of work life. No significant
relation was found between role overload and quality of work life.
Finally, directions for future research are proposed and discussed.