Abstract: A design of communication area for infrared
electronic-toll-collection systems to provide an extended
communication interval in the vehicle traveling direction and
regular boundary between contiguous traffic lanes is proposed.
By utilizing two typical low-cost commercial infrared LEDs with
different half-intensity angles Φ1/2 = 22◦ and 10◦, the radiation
pattern of the emitter is designed to properly adjust the spatial
distribution of the signal power. The aforementioned purpose
can be achieved with an LED array in a three-piece structure
with appropriate mounting angles. With this emitter, the influence
of the mounting parameters, including the mounting height and
mounting angles of the on-board unit and road-side unit, on the
system performance in terms of the received signal strength and
communication area are investigated. The results reveal that, for
our emitter proposed in this paper, the ideal ”long-and-narrow”
characteristic of the communication area is very little affected by
these mounting parameters. An optimum mounting configuration is
also suggested.
Abstract: Color printing proceeds with multiple halftone
separations overlay. Because of separation overlay misalignment in
printing, the percentage of different primary color combination may
vary and it will result in color shift. In traditional printing procedure
with AM halftone, every separation has different screening angle to
make the superposition pattern in a random style, which will reduce
the color shift. To evaluate the color shift of printing with hybrid
halftoning, we simulate printing procedure with halftone images
overlay and calculate the color difference between expected color and
color in different overlay misalignment configurations. The color
difference for hybrid halftone and AM halftone is very close. So the
color shift for hybrid halftone is acceptable with current color printing
procedure.
Abstract: The objective of this paper is to compare the time
specification performance between conventional controller PID and
modern controller SMC for an inverted pendulum system. The goal is
to determine which control strategy delivers better performance with
respect to pendulum-s angle and cart-s position. The inverted
pendulum represents a challenging control problem, which
continually moves toward an uncontrolled state. Two controllers are
presented such as Sliding Mode Control (SMC) and Proportional-
Integral-Derivatives (PID) controllers for controlling the highly
nonlinear system of inverted pendulum model. Simulation study has
been done in Matlab Mfile and simulink environment shows that both
controllers are capable to control multi output inverted pendulum
system successfully. The result shows that Sliding Mode Control
(SMC) produced better response compared to PID control strategies
and the responses are presented in time domain with the details
analysis.
Abstract: This paper reports on investigations into capacity of a
Multiple Input Multiple Output (MIMO) wireless communication
system employing a uniform linear array (ULA) at the transmitter and
either a uniform linear array (ULA) or a uniform circular array (UCA)
antenna at the receiver. The transmitter is assumed to be surrounded by
scattering objects while the receiver is postulated to be free from
scattering objects. The Laplacian distribution of angle of arrival
(AOA) of a signal reaching the receiver is postulated. Calculations of
the MIMO system capacity are performed for two cases without and
with the channel estimation errors. For estimating the MIMO channel,
the scaled least square (SLS) and minimum mean square error
(MMSE) methods are considered.
Abstract: An experiment was performed with a 24.5 MeV 14N
beam on a 12C target in the cyclotron DC-60 located in Astana,
Kazakhstan, to study the elastic scattering of 14N on 12C; the
scattering was also analyzed at different energies for tracking the
phenomenon of remarkable structure at large angles. Its aims were to
extend the measurements to very large angles, and attempt to
uniquely identify the elastic scattering potential. Good agreement
between the theoretical and experimental data has been obtained with
suitable optical potential parameters. Optical model calculations with
l -dependent imaginary potentials were also applied to the data and
relatively good agreement was found.
Abstract: The Želazny Most tailing pond is one of the largest
facilities worldwide for waste disposal from the copper mines located
in South-West Poland. A potential failure of the dam would allow
more than 10 million cubic meters of contaminated slurry to flow to
the valley, causing immense environmental problems to the
surrounding area. Thus, the determination of the strength properties
of the dam's soils and their variability is of utmost importance.
An extensive site investigation consisting of more than 480 cone
penetration tests (CPTs) with or without pore water pressure
measurements were conducted within a period of 13 years to study
the mechanical properties of the tailings body. The present work
investigates the point variability of the soil strength parameters
(effective friction angle
Abstract: An exploratory computational investigation using
RANS & URANS was carried out to understand the aerodynamics
around an isolatedsingle rotating wheel with decreasing ground
proximity. The wheel was initially modeled in free air conditions,
then with decreasing ground proximity and increased yaw angle with
rotational speeds. Three speeds of rotation were applied to the wheel
so that the effect of different angular velocities can be investigated. In
addition to rotation, three different yaw angles were applied to the
rotating wheel in order to understand how these two variables
combined affect the aerodynamic flow field around the wheel.
Abstract: This work presents a numerical model developed to
simulate the dynamics and vibrations of a multistage tractor gearbox.
The effect of time varying mesh stiffness, time varying frictional
torque on the gear teeth, lateral and torsional flexibility of the shafts
and flexibility of the bearings were included in the model. The model
was developed by using the Lagrangian method, and it was applied to
study the effect of three design variables on the vibration and stress
levels on the gears. The first design variable, module, had little effect
on the vibration levels but a higher module resulted to higher bending
stress levels. The second design variable, pressure angle, had little
effect on the vibration levels, but had a strong effect on the stress
levels on the pinion of a high reduction ratio gear pair. A pressure
angle of 25o resulted to lower stress levels for a pinion with 14 teeth
than a pressure angle of 20o. The third design variable, contact ratio,
had a very strong effect on both the vibration levels and bending
stress levels. Increasing the contact ratio to 2.0 reduced both the
vibration levels and bending stress levels significantly. For the gear
train design used in this study, a module of 2.5 and contact ratio of
2.0 for the various meshes was found to yield the best combination
of low vibration levels and low bending stresses. The model can
therefore be used as a tool for obtaining the optimum gear design
parameters for a given multistage spur gear train.
Abstract: In this paper, we propose a solution to the motion
control problem of a 2-link revolute manipulator arm. We require the
end-effector of the arm to move safely to its designated target in a
priori known workspace cluttered with fixed circular obstacles of
arbitrary position and sizes. Firstly a unique velocity algorithm is
used to move the end-effector to its target. Secondly, for obstacle
avoidance a turning angle is designed, which when incorporated into
the control laws ensures that the entire robot arm avoids any number
of fixed obstacles along its path enroute the target. The control laws
proposed in this paper also ensure that the equilibrium point of the
system is asymptotically stable. Computer simulations of the
proposed technique are presented.
Abstract: The flow and heat transfer characteristics for natural
convection along an inclined plate in a saturated porous medium with
an applied magnetic field have been studied. The fluid viscosity has
been assumed to be an inverse function of temperature. Assuming
temperature vary as a power function of distance. The transformed
ordinary differential equations have solved by numerical integration
using Runge-Kutta method. The velocity and temperature profile
components on the plate are computed and discussed in detail for
various values of the variable viscosity parameter, inclination angle,
magnetic field parameter, and real constant (λ). The results have also
been interpreted with the aid of tables and graphs. The numerical
values of Nusselt number have been calculated for the mentioned
parameters.
Abstract: The present work describes a computational study of
aerodynamic characteristics of GLC305 airfoil clean and with 16.7
min ice shape (rime 212) and 22.5 min ice shape (glaze 944).The
performance of turbulence models SA, Kε, Kω Std, and Kω SST
model are observed against experimental flow fields at different
Mach numbers 0.12, 0.21, 0.28 in a range of Reynolds numbers
3x106, 6x106, and 10.5x106 on clean and iced aircraft airfoil
GLC305. Numerical predictions include lift, drag and pitching
moment coefficients at different Mach numbers and at different angle
of attacks were done. Accuracy of solutions with respect to the
effects of turbulence models, variation of Mach number, initial
conditions, grid resolution and grid spacing near the wall made the
study much sensitive. Navier Stokes equation based computational
technique is used. Results are very close to the experimental results.
It has seen that SA and SST models are more efficient than Kε and
Kω standard in under study problem.
Abstract: The machining of Carbon Fiber Reinforced Plastics
has come to constitute a significant challenge for many fields of
industry. The resulting surface finish of machined parts is of primary
concern for several reasons, including contact quality and impact on
the assembly. Therefore, the characterization and prediction of
roughness based on machining parameters are crucial for costeffective
operations. In this study, a PCD tool comprised of two
straight flutes was used to trim 32-ply carbon fiber laminates in a bid
to analyze the effects of the feed rate and the cutting speed on the
surface roughness. The results show that while the speed has but a
slight impact on the surface finish, the feed rate for its part affects it
strongly. A detailed study was also conducted on the effect of fiber
orientation on surface roughness, for quasi-isotropic laminates used
in aerospace. The resulting roughness profiles for the four-ply
orientation lay-up were compared, and it was found that fiber angle is
a critical parameter relating to surface roughness. One of the four
orientations studied led to very poor surface finishes, and
characteristic roughness profiles were identified and found to only
relate to the ply orientations of multilayer carbon fiber laminates.
Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: In intensity modulated radiation therapy (IMRT)
treatment planning, beam angles are usually preselected on the basis of
experience and intuition. Therefore, getting an appropriate beam
configuration needs a very long time. Based on the present situation,
the paper puts forward beam orientation optimization using ant colony
optimization (ACO). We use ant colony optimization to select the
beam configurations, after getting the beam configuration using
Conjugate Gradient (CG) algorithm to optimize the intensity profiles.
Combining with the information of the effect of pencil beam, we can
get the global optimal solution accelerating. In order to verify the
feasibility of the presented method, a simulated and clinical case was
tested, compared with dose-volume histogram and isodose line
between target area and organ at risk. The results showed that the
effect was improved after optimizing beam configurations. The
optimization approach could make treatment planning meet clinical
requirements more efficiently, so it had extensive application
perspective.
Abstract: The aim of this paper is to study the oblique
stagnation point flow on vertical plate with uniform surface heat flux
in presence of magnetic field. Using Stream function, partial
differential equations corresponding to the momentum and energy
equations are converted into non-linear ordinary differential
equations. Numerical solutions of these equations are obtained using
Runge-Kutta Fehlberg method with the help of shooting technique.
In the present work the effects of striking angle, magnetic field
parameter, Grashoff number, the Prandtl number on velocity and heat
transfer characteristics have been discussed. Effect of above
mentioned parameter on the position of stagnation point are also
studied.
Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: This paper describes a complex energy signal model
that is isomorphic with digital human fingerprint images. By using
signal models, the problem of fingerprint matching is transformed
into the signal processing problem of finding a correlation between
two complex signals that differ by phase-rotation and time-scaling. A
technique for minutiae matching that is independent of image
translation, rotation and linear-scaling, and is resistant to missing
minutiae is proposed. The method was tested using random data
points. The results show that for matching prints the scaling and
rotation angles are closely estimated and a stronger match will have a
higher correlation.
Abstract: Most electrical distribution systems are incurring large
losses as the loads are wide spread, inadequate reactive power
compensation facilities and their improper control. A typical static
VAR compensator consists of capacitor bank in binary sequential
steps operated in conjunction with a thyristor controlled reactor of the
smallest step size. This SVC facilitates stepless control of reactive
power closely matching with load requirements so as to maintain
power factor nearer to unity. This type of SVC-s requiring a
appropriately controlled TCR. This paper deals with an air cored
reactor suitable for distribution transformer of 3phase, 50Hz, Dy11,
11KV/433V, 125 KVA capacity. Air cored reactors are designed,
built, tested and operated in conjunction with capacitor bank in five
binary sequential steps. It is established how the delta connected TCR
minimizes the harmonic components and the operating range for
various electrical quantities as a function of firing angle is
investigated. In particular firing angle v/s line & phase currents, D.C.
components, THD-s, active and reactive powers, odd and even triplen
harmonics, dominant characteristic harmonics are all investigated and
range of firing angle is fixed for satisfactory operation. The harmonic
spectra for phase and line quantities at specified firing angles are
given. In case the TCR is operated within the bound specified in this
paper established through simulation studies are yielding the best
possible operating condition particularly free from all dominant
harmonics.
Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.
Abstract: The purpose of this study was to explore the complex
flow structure a novel active-type micromixer that based on concept of
Wankle-type rotor. The characteristics of this micromixer are two
folds; a rapid mixing of reagents in a limited space due to the
generation of multiple vortices and a graduate increment in dynamic
pressure as the mixed reagents is delivered to the output ports.
Present micro-mixer is consisted of a rotor with shape of triangle
column, a blending chamber and several inlet and outlet ports. The
geometry of blending chamber is designed to make the rotor can be
freely internal rotated with a constant eccentricity ratio. When the
shape of the blending chamber and the rotor are fixed, the effects of
rotating speed of rotor and the relative locations of ports on the mixing
efficiency are numerical studied. The governing equations are
unsteady, two-dimensional incompressible Navier-Stokes equation
and the working fluid is the water. The species concentration equation
is also solved to reveal the mass transfer process of reagents in various
regions then to evaluate the mixing efficiency.
The dynamic mesh technique was implemented to model the
dynamic volume shrinkage and expansion of three individual
sub-regions of blending chamber when the rotor conducted a complete
rotating cycle. Six types of ports configuration on the mixing
efficiency are considered in a range of Reynolds number from 10 to
300. The rapid mixing process was accomplished with the multiple
vortex structures within a tiny space due to the equilibrium of shear
force, viscous force and inertial force. Results showed that the highest
mixing efficiency could be attained in the following conditions: two
inlet and two outlet ports configuration, that is an included angle of 60
degrees between two inlets and an included angle of 120 degrees
between inlet and outlet ports when Re=10.