Abstract: Block replacement algorithms to increase hit ratio
have been extensively used in cache memory management. Among
basic replacement schemes, LRU and FIFO have been shown to be
effective replacement algorithms in terms of hit rates. In this paper,
we introduce a flexible stack-based circuit which can be employed in
hardware implementation of both LRU and FIFO policies. We
propose a simple and efficient architecture such that stack-based
replacement algorithms can be implemented without the drawbacks
of the traditional architectures. The stack is modular and hence, a set
of stack rows can be cascaded depending on the number of blocks in
each cache set. Our circuit can be implemented in conjunction with
the cache controller and static/dynamic memories to form a cache
system. Experimental results exhibit that our proposed circuit
provides an average value of 26% improvement in storage bits and its
maximum operating frequency is increased by a factor of two
Abstract: This paper presents the results of an experimental study on the performance of a triboelectric separator of plastic mixtures used for recycling. The separator consists of four cylindrical electrodes. The principle behind the separation technique is based on the difference in the Coulomb force acting on the plastic particles after triboelectric charging. The separation of mixtures of acrylonitrile butadiene styrene (ABS) and polystyrene (PS) using this method was studied. The effects of the triboelectric charging time and applied voltage on the separation efficiency were investigated. The experimental results confirm that it is possible to obtain a high purity and recovery rate for the initial compositions considered in this study.
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.
Abstract: Loop detectors report traffic characteristics in real
time. They are at the core of traffic control process. Intuitively,
one would expect that as density of detection increases, so would
the quality of estimates derived from detector data. However, as
detector deployment increases, the associated operating and
maintenance cost increases. Thus, traffic agencies often need to
decide where to add new detectors and which detectors should
continue receiving maintenance, given their resource constraints.
This paper evaluates the effect of detector spacing on freeway
travel time estimation. A freeway section (Interstate-15) in Salt
Lake City metropolitan region is examined. The research reveals
that travel time accuracy does not necessarily deteriorate with
increased detector spacing. Rather, the actual location of detectors
has far greater influence on the quality of travel time estimates.
The study presents an innovative computational approach that
delivers optimal detector locations through a process that relies on
Genetic Algorithm formulation.
Abstract: The main issue discussed is on the role of education system in the process of nation building as a means in uniting different community ethnics which later on, hoped to shape the future ethnic relation of this country. It is generally known that political socialization experienced by each ethnic community has given birth to a vernacular education system, separated along the ethnic line. Every community shapes their own education system based on their respective mother tongue language, however all are based on the same curriculum. As a result the role of education as a uniting force is not significantly effective. Historically, it has been shown that government efforts to unite the country education system under the wing of national education system (national school) is not that successful since every community (Chinese) will defend the existence of their community education system because they want to spur their mother tongue language. The clash between national education system and vernacular education system is the root cause of stalemate in the ethnic relation in Malaysia and it always becomes a flash point when the issue is raised. The question now is what is the best solution to enhance the national education system in multiethnic Malaysia?
Abstract: In production of medicinal plants, seed germination is
very important problem. The treated seeds (control, hydro priming
and ZnSO4) of Cumin (Cuminum cyminum L.) were evaluated at
germination and seedling growth for tolerance to salt (NaCl and
Na2SO4) conditions at the same water potentials of 0.0, -0.3, -0.6, -
0.9 and -1.2MPa. Electrical conductivity (EC) values of the NaCl
solutions were 0.0, 6.5, 12.7, 18.4 and 23.5 dSm-1, respectively. The
objective of the study was to determine factors responsible for
germination and early seedling growth due to salt toxicity or osmotic
effect and to optimize the best priming treatment for these stress
conditions. Results revealed that germination delayed in both
solutions, having variable germination with different priming
treatments. Germination, shoot and weight, root and shoot length
were higher but mean germination time and abnormal germination
percentage were lower in NaCl than Na2SO4 at the same water
potential. The root / shoot weight and R/S length increased with
increase in osmotic potential in both NaCl and Na2SO4 solutions.
NaCl had less inhibitor effect on seedling growth than the
germination. It was concluded that inhibition of germination at the
same water potential of NaCl and Na2SO4 resulted from salt toxicity
rather than osmotic effect. Hydro priming increased germination and
seedling growth under salt stress. This protocol has practical
importance and could be recommended to farmers to achieve higher
germination and uniform emergence under field conditions.
Abstract: There is need to explore emerging technologies based on carbon nanotube electronics as the MOS technology is approaching its limits. As MOS devices scale to the nano ranges, increased short channel effects and process variations considerably effect device and circuit designs. As a promising new transistor, the Carbon Nanotube Field Effect Transistor(CNTFET) avoids most of the fundamental limitations of the Traditional MOSFET devices. In this paper we present the analysis and comparision of a Carbon Nanotube FET(CNTFET) based 10(A current mirror with MOSFET for 32nm technology node. The comparision shows the superiority of the former in terms of 97% increase in output resistance,24% decrease in power dissipation and 40% decrease in minimum voltage required for constant saturation current. Furthermore the effect on performance of current mirror due to change in chirality vector of CNT has also been investigated. The circuit simulations are carried out using HSPICE model.
Abstract: The expression of LFA-1 diverges from the
physiological condition, thus active targeting carrier can provide the
benefits from difference into LFA-1 expression in various conditions.
Here, the selectivity of cIBR-conjugated nanoparticles (cIBR-NPs),
in terms of uptake, was investigated using PBMCs, Mixed PBMCMolt-
3 cells and Molt-3 cells. The expressions of LFA-1 on Molt-3
cells, from flow cytometry and Western blot, possessed the highest
level whereas PBMCs showed the lowest level. The kinetic uptake
profiles of cIBR-NPs were obtained by flow cytometry, which the
degree of cellular uptake presented a similar trend with the level of
LFA-1 indicating the influence of LFA-1 expression on the cellular
uptake of cIBR-NPs. The conformation of LFA-1 had a slight effect
on the cellular uptake of cIBR-NPs. Overall we demonstrated that
cIBR-NPs enhanced cellular uptake and improved the selectivity of
drug carriers to LFA-1 on the leukemia cells, which related with the
order of LFA-1 expression.
Abstract: Utilization of bagasse ash for silica sources is one of
the most common application for agricultural wastes and valuable
biomass byproducts in sugar milling. The high percentage silica
content from bagasse ash was used as silica source for sodium
silicate solution. Different heating temperature, time and acid
treatment were studies for silica extraction. The silica was
characterized using various techniques including X-ray fluorescence,
X-ray diffraction, Scanning electron microscopy, and Fourier
Transform Infrared Spectroscopy method,. The synthesis conditions
were optimized to obtain the bagasse ash with the maximum silica
content. The silica content of 91.57 percent was achieved from
heating of bagasse ash at 600°C for 3 hours under oxygen feeding
and HCl treatment. The result can be used as value added for bagasse
ash utilization and minimize the environmental impact of disposal
problems.
Abstract: Pentachlorophenol (PCP) is a polychlorinated
aromatic compound that is widespread in industrial effluents and is
considered to be a serious pollutant. Among the variety of industrial
effluents encountered, effluents from tanning industry are very
important and have a serious pollution potential. PCP is also formed
unintentionally in effluents of paper and pulp industries. It is highly
persistent in soils and is lethal to a wide variety of beneficial
microorganisms and insects, human beings and animals. The natural
processes that breakdown toxic chemicals in the environment have
become the focus of much attention to develop safe and environmentfriendly
deactivation technologies. Microbes and plants are among
the most important biological agents that remove and degrade waste
materials to enable their recycling in the environment. The present
investigation was carried out with the aim of developing a microbial
system for bioremediation of PCP polluted soils. A number of plant
species were evaluated for their ability to tolerate different
concentrations of pentachlorophenol (PCP) in the soil. The
experiment was conducted for 30 days under pot culture conditions.
The toxic effect of PCP on plants was studied by monitoring seed
germination, plant growth and biomass. As the concentration of PCP
was increased to 50 ppm, the inhibition of seed germination, plant
growth and biomass was also increased. Although PCP had a
negative effect on all plant species tested, maize and groundnut
showed the maximum tolerance to PCP. Other tolerating crops
included wheat, safflower, sunflower, and soybean. From the
rhizosphere soil of the tolerant seedlings, as many as twenty seven
PCP tolerant bacteria were isolated. From soybean, 8; sunflower, 3;
safflower 8; maize 2; groundnut and wheat, 3 each isolates were
made. They were screened for their PCP degradation potentials.
HPLC analyses of PCP degradation revealed that the isolate MAZ-2
degraded PCP completely. The isolate MAZ-1 was the next best
isolate with 90 per cent PCP degradation. These strains hold promise
to be used in the bioremediation of PCP polluted soils.
Abstract: In a wind power generator using doubly fed induction
generator (DFIG), the three-phase pulse width modulation (PWM)
voltage source converter (VSC) is used as grid side converter (GSC)
and rotor side converter (RSC). The standard linear control laws
proposed for GSC provides not only instablity against comparatively
large-signal disturbances, but also the problem of stability due to
uncertainty of load and variations in parameters. In this paper, a
nonlinear controller is designed for grid side converter (GSC) of a
DFIG for wind power application. The nonlinear controller is
designed based on the input-output feedback linearization control
method. The resulting closed-loop system ensures a sufficient
stability region, make robust to variations in circuit parameters and
also exhibits good transient response. Computer simulations and
experimental results are presented to confirm the effectiveness of the
proposed control strategy.
Abstract: In this paper, a parametric experimental study for producing paving blocks using fine and coarse waste glass is presented. Some of the physical and mechanical properties of paving blocks having various levels of fine glass (FG) and coarse glass (CG) replacements with fine aggregate (FA) are investigated. The test results show that the replacement of FG by FA at level of 20% by weight has a significant effect on the compressive strength, flexural strength, splitting tensile strength and abrasion resistance of the paving blocks as compared with the control sample because of puzzolanic nature of FG. The compressive strength, flexural strength, splitting tensile strength and abrasion resistance of the paving block samples in the FG replacement level of 20% are 69%, 90%, 47% and 15 % higher as compared with the control sample respectively. It is reported in the earlier works the replacement of FG by FA at level of 20% by weight suppress the alkali-silica reaction (ASR) in the concrete. The test results show that the FG at level of 20% has a potential to be used in the production of paving blocks. The beneficial effect on these properties of CG replacement with FA is little as compared with FG.
Abstract: The article examines the methods of protection of
citizens' personal data on the Internet using biometric identity
authentication technology. It`s celebrated their potential danger due
to the threat of loss of base biometric templates. To eliminate the
threat of compromised biometric templates is proposed to use neural
networks large and extra-large sizes, which will on the one hand
securely (Highly reliable) to authenticate a person by his biometrics,
and on the other hand make biometrics a person is not available for
observation and understanding. This article also describes in detail
the transformation of personal biometric data access code. It`s formed
the requirements for biometrics converter code for his work with the
images of "Insider," "Stranger", all the "Strangers". It`s analyzed the
effect of the dimension of neural networks on the quality of
converters mystery of biometrics in access code.
Abstract: The hydrodynamic and thermal lattice Boltzmann
methods are applied to investigate the turbulent convective heat
transfer in the wavy channel flows. In this study, the turbulent
phenomena are modeling by large-eddy simulations with the
Smagorinsky model. As a benchmark, the laminar and turbulent
backward-facing step flows are simulated first. The results give good
agreement with other numerical and experimental data. For wavy
channel flows, the distribution of Nusselt number and the skin-friction
coefficients are calculated to evaluate the heat transfer effect and the
drag force. It indicates that the vortices at the trough would affect the
magnitude of drag and weaken the heat convection effects on the wavy
surface. In turbulent cases, if the amplitude of the wavy boundary is
large enough, the secondary vortices would be generated at troughs
and contribute to the heat convection. Finally, the effects of different
Re on the turbulent transport phenomena are discussed.
Abstract: This paper discusses the development of a qualitative
simulator (abbreviated QRiOM) for predicting the behaviour of
organic chemical reactions. The simulation technique is based on the
qualitative process theory (QPT) ontology. The modelling constructs
of QPT embody notions of causality which can be used to explain the
behaviour of a chemical system. The major theme of this work is
that, in a qualitative simulation environment, students are able to
articulate his/her knowledge through the inspection of explanations
generated by software. The implementation languages are Java and
Prolog. The software produces explanation in various forms that
stresses on the causal theories in the chemical system which can be
effectively used to support learning.
Abstract: Breast carcinoma is the most common form of cancer
in women. Multicolour fluorescent in-situ hybridisation (m-FISH) is
a common method for staging breast carcinoma. The interpretation
of m-FISH images is complicated due to two effects: (i) Spectral
overlap in the emission spectra of fluorochrome marked DNA probes
and (ii) tissue autofluorescence. In this paper hyper-spectral images of
m-FISH samples are used and spectral unmixing is applied to produce
false colour images with higher contrast and better information
content than standard RGB images. The spectral unmixing is realised
by combinations of: Orthogonal Projection Analysis (OPA), Alterating
Least Squares (ALS), Simple-to-use Interactive Self-Modeling
Mixture Analysis (SIMPLISMA) and VARIMAX. These are applied
on the data to reduce tissue autofluorescence and resolve the spectral
overlap in the emission spectra. The results show that spectral unmixing
methods reduce the intensity caused by tissue autofluorescence by
up to 78% and enhance image contrast by algorithmically reducing
the overlap of the emission spectra.
Abstract: This research was conducted to develop a correlation
between microstructure of HSLA steel and the mechanical properties
that occur as a result of both laser and mechanical forming processes
of the metal. The technique of forming flat metals by applying laser
beams is a relatively new concept in the manufacturing industry.
However, the effects of laser energy on the stability of metal alloy
phases have not yet been elucidated in terms of phase
transformations and microhardness. In this work, CO2 laser source
was used to irradiate the surface of a flat metal then the
microstructure and microhardness of the metal were studied on the
formed specimen. The extent to which the microstructure changed
depended on the heat inputs of up to 1000 J/cm2 with cooling rates of
about 4.8E+02 K/s. Experimental results revealed that the irradiated
surface of a HSLA steel had transformed to austenitic structure
during the heating process.
Abstract: Advances in computing applications in recent years
have prompted the demand for more flexible scheduling models for
QoS demand. Moreover, in practical applications, partly violated
temporal constraints can be tolerated if the violation meets certain
distribution. So we need extend the traditional Liu and Lanland model
to adapt to these circumstances. There are two extensions, which are
the (m, k)-firm model and Window-Constrained model. This paper
researches on weakly hard real-time constraints and their combination
to support QoS. The fact that a practical application can tolerate some
violations of temporal constraint under certain distribution is
employed to support adaptive QoS on the open real-time system. The
experiment results show these approaches are effective compared to
traditional scheduling algorithms.
Abstract: Study is on the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. The effects of the FGM configuration are studied by studying the frequencies of FG cylindrical shells. In this case FG cylindrical shell has Nickel on its inner surface and stainless steel on its outer surface. The study is carried out based on third order shear deformation shell theory. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of configurations of the constituent materials on the frequencies. The properties are graded in the thickness direction according to the volume fraction power-law distribution. Results are presented on the frequency characteristics, the influence of the constituent various volume fractions on the frequencies.
Abstract: The accomplished study is based on the appointment
and identification of ageing effects and according to this absorption
of moisture of aircraft cabin components over the life-cycle. In the
first step of the study ceiling panels from same age and from the
same aircraft cabin have been examined according to weight changes
depending on the position in the aircraft cabin. In the second step of
the study different aged ceiling panels have been examined
concerning deflection, weight changes and the acoustic sound
transmission loss. To prove the assumption of water absorption
within the study and with the theoretical background from literature
and scientific papers, an older test panel was exposed extreme
thermal conditions (humidity and temperature) within a climate
chamber to show that there is a general ingress of water to cabin
components and that this ingress of water leads to the change of
different mechanical properties.