Abstract: Machining parameters are very important in
determining the surface quality of any material. In the past decade,
some new engineering materials were developed for the
manufacturing industry which created a need to conduct an
investigation on the impact of the said parameters on their surface
roughness. Polyurethane (PU) block is widely used in the automotive
industry to manufacture parts such as checking fixtures that are used
to verify the dimensional accuracy of automotive parts. In this paper,
the design of experiment (DOE) was used to investigate on the effect
of the milling parameters on the PU block. Furthermore, an analysis
of the machined surface chemical composition was done using
scanning electron microscope (SEM). It was found that the surface
roughness of the PU block is severely affected when PU undergoes a
flood machining process instead of a dry condition. In addition the
stepover and the silicon content were found to be the most significant
parameters that influence the surface quality of the PU block.
Abstract: The computational fluid dynamics (CFD) study of
stirred tank with the air-water interface are carried out in the presence
of different types of the impeller and with or without baffles. A
multiple reference frame (MRF) approach with the volume of fluid
(VOF) method is used to capture the air-water interface. The RANS
(Reynolds Averaged Navier-Stokes) equations with k-ε turbulence
model are solved to predict the flow behavior of water and air phase
which are treated as a different phases. The predicted results have
shown that the VOF method is able to capture the interface in the
unbaffled tank. While, the VOF method is showing an unfeasible
results in the baffled tank with high rotational impeller speed. For
continuous stirred tank, the air-water interface is disturbed by the
inflow and the level of water is also increased with time.
Abstract: Rhodamine B (RB) is a toxic dye used extensively in
textile industry, which must be remediated before its drainage to
environment. In the present study, supported gold nanoparticles on
commercially available titania and zincite were successfully prepared
and then their activity on the photodegradation of RB under UV A
light irradiation were evaluated. The synthesized photocatalysts were
characterized by ICP, BET, XRD, and TEM. Kinetic results showed
that Au/TiO2 was an inferior photocatalyst to Au/ZnO. This
observation could be attributed to the strong reflection of UV
irradiation by gold nanoparticles over TiO2 support.
Abstract: Bamboo is extensively used in construction industry.
Low durability of bamboo due to fungus infestation and termites
attack under storage puts certain constrains for it usage as modern
structural material. Looking at many chemical formulations for
bamboo treatment leading to severe harmful environment effects,
research on eco-friendly preservatives for bamboo treatment has been
initiated world-over. In the present studies, eco-friendly preservative
for bamboo treatment has been developed. To validate its application
for structural purposes, investigation of effect of treatment on
compressive strength has been investigated. Neemoil (25%)
integrated with copper naphthenate (0.3%) on dilution with kerosene
oil impregnated into bamboo culm at 2 bar pressure, has shown
weight loss of only 3.15% in soil block analysis method. The results
from compressive strength analysis using HEICO Automatic
Compression Testing Machine reveal that preservative treatment has
not altered the structural properties of bamboo culms. Compressive
strength of control (11.72 N/mm2) and above treated samples (11.71
N/mm2) was found to be comparable.
Abstract: Fuzzy inference method based approach to the
forming of modular intellectual system of assessment the quality of
communication services is proposed. Developed under this approach
the basic fuzzy estimation model takes into account the
recommendations of the International Telecommunication Union in
respect of the operation of packet switching networks based on IPprotocol.
To implement the main features and functions of the fuzzy
control system of quality telecommunication services it is used
multilayer feedforward neural network.
Abstract: Metal matrix composites (MMCs) attract considerable
attention as a result from its ability in providing a high strength, high
modulus, high toughness, high impact properties, improving wear
resistance and providing good corrosion resistance compared to
unreinforced alloy. Aluminium Silicon (Al/Si) alloy MMC has been
widely used in various industrial sectors such as in transportation,
domestic equipment, aerospace, military, construction, etc.
Aluminium silicon alloy is an MMC that had been reinforced with
aluminium nitrate (AlN) particle and become a new generation
material use in automotive and aerospace sector. The AlN is one of
the advance material that have a bright prospect in future since it has
features such as lightweight, high strength, high hardness and
stiffness quality. However, the high degree of ceramic particle
reinforcement and the irregular nature of the particles along the
matrix material that contribute to its low density is the main problem
which leads to difficulties in machining process. This paper examined
the tool wear when milling AlSi/AlN Metal Matrix Composite using
a TiB2 (Titanium diboride) coated carbide cutting tool. The volume
of the AlN reinforced particle was 10% and milling process was
carried out under dry cutting condition. The TiB2 coated carbide
insert parameters used were at the cutting speed of (230, 300 and
370m/min, feed rate of 0.8, Depth of Cut (DoC) at 0.4m). The
Sometech SV-35 video microscope system used to quantify of the
tool wear. The result shown that tool life span increasing with the
cutting speeds at (370m/min, feed rate of 0.8mm/tooth and DoC at
0.4mm) which constituted an optimum condition for longer tool life
lasted until 123.2 mins. Meanwhile, at medium cutting speed which
at 300m/m, feed rate of 0.8mm/tooth and depth of cut at 0.4mm we
found that tool life span lasted until 119.86 mins while at low cutting
speed it lasted in 119.66 mins. High cutting speed will give the best
parameter in cutting AlSi/AlN MMCs material. The result will help
manufacturers in machining process of AlSi/AlN MMCs materials.
Abstract: Red blood cells (RBC) are the most common types of
blood cells and are the most intensively studied in cell biology. The
lack of RBCs is a condition in which the amount of hemoglobin level
is lower than normal and is referred to as “anemia”. Abnormalities in
RBCs will affect the exchange of oxygen. This paper presents a
comparative study for various techniques for classifying the RBCs as
normal or abnormal (anemic) using WEKA. WEKA is an open
source consists of different machine learning algorithms for data
mining applications. The algorithms tested are Radial Basis Function
neural network, Support vector machine, and K-Nearest Neighbors
algorithm. Two sets of combined features were utilized for
classification of blood cells images. The first set, exclusively consist
of geometrical features, was used to identify whether the tested blood
cell has a spherical shape or non-spherical cells. While the second
set, consist mainly of textural features was used to recognize the
types of the spherical cells. We have provided an evaluation based on
applying these classification methods to our RBCs image dataset
which were obtained from Serdang Hospital - Malaysia, and
measuring the accuracy of test results. The best achieved
classification rates are 97%, 98%, and 79% for Support vector
machines, Radial Basis Function neural network, and K-Nearest
Neighbors algorithm respectively.
Abstract: The classroom of the 21st century is an ever changing
forum for new and innovative thoughts and ideas. With increasing
technology and opportunity, students have rapid access to
information that only decades ago would have taken weeks to obtain.
Unfortunately, new techniques and technology are not the cure for
the fundamental problems that have plagued the classroom ever since
education was established. Class size has been an issue long debated
in academia. While it is difficult to pin point an exact number, it is
clear that in this case more does not mean better. By looking into the
success and pitfalls of classroom size the true advantages of smaller
classes will become clear. Previously, one class was comprised of 50
students. Being seventeen and eighteen- year- old students,
sometimes it was quite difficult for them to stay focused. To help
them understand and gain much knowledge, a researcher introduced
“The Theory of Multiple Intelligence” and this, in fact, enabled
students to learn according to their own learning preferences no
matter how they were being taught. In this lesson, the researcher
designed a cycle of learning activities involving all intelligences so
that everyone had equal opportunities to learn.
Abstract: Solar air heater is a type of heat exchanger which
transforms solar radiation into heat energy. The thermal performance
of conventional solar air heater has been found to be poor because of
the low convective heat transfer coefficient from the absorber plate to
the air. It is attributed to the formation of a very thin boundary layer
at the absorber plate surface commonly known as viscous sub-layer.
Thermal efficiency of solar air heater can be improved by providing
the artificial roughness on absorber plate is the most efficient
technique. In this paper an attempt is made to provide artificial
roughness by incorporating inclined multiple V-ribs in the underside
of the absorber plate. 60˚V – ribs are arranged inclined to the
direction of air flow. Performance of collector estimated theoretically
and experimentally. Results of the investigation reveal that thermal
efficiency of collector with multiple V-ribs increased by 14%.
Abstract: Lead being a toxic heavy metal that mankind is
exposed to the highest levels of this metal from environmental
pollutants. A total of 180 Male scalp hair samples were collected
from different environments in Greater Cairo (GC), i.e. industrial,
heavy traffic and rural areas (60 samples from each) having different
activities during the period of, 1/5/2010 to 1/11/2012. Hair samples
were collected during five stages. Data proved that the concentration
of lead in male industrial areas of Cairo ranged between 6.2847 to
19.0432 μg/g, with mean value of 12.3288 μg/g. On the other hand,
lead content of hair samples of residential-traffic areas ranged
between 2.8634 to 16.3311 μg/g with mean value of 9.7552 μg/g.
While lead concentration on the hair of the male residents living in
rural area ranged between 1.0499-9.0402μg/g with mean value of
4.7327 μg/g. The Pb concentration in scalp hair of Cairo residents of
residential-traffic and rural traffic areas was observed to follow the
same pattern. The pattern was that of decrease concentration of
summer and its increase in winter. Then, there was a marked increase
in Pb concentration of summer 2012, and this increase was
significant. These were obviously seen for the residential-traffic and
rural areas residents. Pb pollution in residents of industrial areas
showed the same seasonal pattern, but there was marked to decrease
in Pb concentration of summer 2012, and this decrease was
significant. Lead pollution in residents of GC was serious. It is worth
noting that the atmosphere is still contaminated by lead despite a
decade of using unleaded gasoline. Strong seasonal variation in
higher Pb concentration on winter than in summer was found. Major
contributions to the pollution with Pb could include industry
emissions, motor vehicle emissions and long transported dust from
outside Cairo. More attention should be paid to the reduction of Pb
content of the urban aerosol and to the Pb pollution health.
Abstract: The levels of maximum power density of GSM
signals in the cities of Lagos, Ibadan and Abuja were studied.
Measurements were made with a calibrated hand held spectrum
analyzer 200m away from 271 base stations, at 1.2m to the ground
level. The maximum GSM 900 signal power density was
139.63μW/m2 in Lagos, 162.49μW/m2 in Ibadan and 5411.26μW/m2
in Abuja. Also, the maximum GSM 1800 signal power density was
296.82μW/m2 in Lagos, 116.82μW/m2 in Ibadan and 1263.00μW/m2
in Abuja. The level of power density of GSM 900 and GSM 1800
signals in the cities of Lagos, Ibadan and Abuja are far less than the
recommended value of 4.5W/m2 for GSM 900 and 9.0 W/m2 for
GSM 1800 by the ICNRP guideline. It can be concluded that
exposure to GSM signals in these cities cannot contribute to the
health detriments caused by thermal effects of radiofrequency
radiation.
Abstract: Image spam is a kind of email spam where the spam
text is embedded with an image. It is a new spamming technique
being used by spammers to send their messages to bulk of internet
users. Spam email has become a big problem in the lives of internet
users, causing time consumption and economic losses. The main
objective of this paper is to detect the image spam by using histogram
properties of an image. Though there are many techniques to
automatically detect and avoid this problem, spammers employing
new tricks to bypass those techniques, as a result those techniques are
inefficient to detect the spam mails. In this paper we have proposed a
new method to detect the image spam. Here the image features are
extracted by using RGB histogram, HSV histogram and combination
of both RGB and HSV histogram. Based on the optimized image
feature set classification is done by using k- Nearest Neighbor(k-NN)
algorithm. Experimental result shows that our method has achieved
better accuracy. From the result it is known that combination of RGB
and HSV histogram with k-NN algorithm gives the best accuracy in
spam detection.
Abstract: Steganography is the art and science that hides the information in an appropriate cover carrier like image, text, audio and video media. In this work the authors propose a new image based steganographic method for hiding information within the complex bit planes of the image. After slicing into bit planes the cover image is analyzed to extract the most complex planes in decreasing order based on their bit plane complexity. The complexity function next determines the complex noisy blocks of the chosen bit plane and finally pixel mapping method (PMM) has been used to embed secret bits into those regions of the bit plane. The novel approach of using pixel mapping method (PMM) in bit plane domain adaptively embeds data on most complex regions of image, provides high embedding capacity, better imperceptibility and resistance to steganalysis attack.
Abstract: The method of introducing the proxy interpretation for
sending and receiving requests increase the capability of the server
and our approach UDIV (User-Data Identity Security) to solve the
data and user authentication without extending size of the data makes
better than hybrid IDS (Intrusion Detection System). And at the same
time all the security stages we have framed have to pass through less
through that minimize the response time of the request. Even though
an anomaly detected, before rejecting it the proxy extracts its identity
to prevent it to enter into system. In case of false anomalies, the
request will be reshaped and transformed into legitimate request for
further response. Finally we are holding the normal and abnormal
requests in two different queues with own priorities.
Abstract: The growth in the volume of text data such as books
and articles in libraries for centuries has imposed to establish
effective mechanisms to locate them. Early techniques such as
abstraction, indexing and the use of classification categories have
marked the birth of a new field of research called "Information
Retrieval". Information Retrieval (IR) can be defined as the task of
defining models and systems whose purpose is to facilitate access to
a set of documents in electronic form (corpus) to allow a user to find
the relevant ones for him, that is to say, the contents which matches
with the information needs of the user.
Most of the models of information retrieval use a specific data
structure to index a corpus which is called "inverted file" or "reverse
index".
This inverted file collects information on all terms over the corpus
documents specifying the identifiers of documents that contain the
term in question, the frequency of each term in the documents of the
corpus, the positions of the occurrences of the word...
In this paper we use an oriented object database (db4o) instead of
the inverted file, that is to say, instead to search a term in the inverted
file, we will search it in the db4o database.
The purpose of this work is to make a comparative study to see if
the oriented object databases may be competing for the inverse index
in terms of access speed and resource consumption using a large
volume of data.
Abstract: The edge waviness in hot rolled steel is a common
defect. Variables that affect such defect include raw material and
machine. These variables are necessary to consider to understand
such defect. This research studied the defect of edge waviness for SS
400 of metal sheet manufacture. Defect of metal sheets were divided
into two groups. The specimens were investigated on chemical
composition and mechanical properties to find the difference. The
results of investigation showed that the difference was not significant.
Therefore the roll mill machine should be used to adjust to support
another location on a roller to avoide edge waviness.
Abstract: In this paper, the dynamic characteristics of a threelobe
journal bearing lubricated with micropolar fluids are determined
by the linear stability theory. Lubricating oil containing additives and
contaminants is modelled as micropolar fluid. The modified
Reynolds equation is obtained using the micropolar lubrication theory
.The finite difference technique has been used to determine the
solution of the modified Reynolds equation. The dynamic
characteristics in terms of stiffness, damping coefficients, the critical
mass and whirl ratio are determined for various values of size of
material characteristic length and the coupling number. The
computed results show that the three-lobe bearing lubricated with
micropolar fluid exhibits better stability compared with that
lubricated with Newtonian fluid. According to the results obtained,
the effect of the parameter micropolar fluid is remarkable on the
dynamic characteristics and stability of the three-lobe bearing.
Abstract: Many of the ever-growing elderly population require
exercise, such as running, for health management. One important
element of a runner’s training is the choice of shoes for exercise; shoes
are important because they provide the interface between the feet and
road. When we purchase shoes, we may instinctively choose a pair
after trying on many different pairs of shoes. Selecting the shoes
instinctively may work, but it does not guarantee a suitable fit for
running activities. Therefore, if we could select suitable shoes for each
runner from the viewpoint of brain activities, it would be helpful for
validating shoe selection. In this paper, we describe how brain
activities show different characteristics during particular task,
corresponding to different properties of shoes. Using five subjects, we
performed a verification experiment, applying weight, softness, and
flexibility as shoe properties. In order to affect the shoe property’s
differences to the brain, subjects run for 10 min. Before and after
running, subjects conducted a paced auditory serial addition task
(PASAT) as the particular task; and the subjects’ brain activities
during the PASAT are evaluated based on oxyhemoglobin and
deoxyhemoglobin relative concentration changes, measured by
near-infrared spectroscopy (NIRS). When the brain works actively,
oxihemoglobin and deoxyhemoglobin concentration drastically
changes; therefore, we calculate the maximum values of concentration
changes. In order to normalize relative concentration changes after
running, the maximum value are divided by before running maximum
value as evaluation parameters. The classification of the groups of
shoes is expressed on a self-organizing map (SOM). As a result,
deoxyhemoglobin can make clusters for two of the three types of
shoes.
Abstract: Reburning is a useful technology in reducing nitric
oxide through injection of a secondary hydrocarbon fuel. In this paper,
an experimental study has been conducted to evaluate the effect of fuel
lean reburning on NOx/CO reduction in LNG flame. Experiments
were performed in flames stabilized by a co-flow swirl burner, which
was mounted at the bottom of the furnace. Tests were conducted using
LNG gas as the reburn fuel as well as the main fuel. The effects of
reburn fuel fraction and injection manner of the reburn fuel were
studied when the fuel lean reburning system was applied. The paper
reports data on flue gas emissions and temperature distribution in the
furnace for a wide range of experimental conditions. At steady state,
temperature distribution and emission formation in the furnace have
been measured and compared. This paper makes clear that in order to
decrease both NOx and CO concentrations in the exhaust when the
pulsated fuel lean reburning system was adapted, it is important that
the control of some factors such as frequency and duty ratio. Also it
shows the fuel lean reburning is also effective method to reduce NOx
as much as reburning.
Abstract: The effect of a 3-dimensional (3D) blade on the turbine
characteristics of Wells turbine for wave energy conversion has been
investigated experimentally by model testing under steady flow
conditions in this study, in order to improve the peak efficiency and
stall characteristics. The aim of use of 3D blade is to prevent flow
separation on the suction surface near the tip. The chord length is
constant with radius and the blade profile changes gradually from the
mean radius to tip. The proposed blade profiles in the study are
NACA0015 from the hub to mean radius and NACA0025 at the tip.
The performances of Wells turbine with 3D blades has been compared
with those of the original Wells turbine, i.e., the turbine with
2-dimensional (2D) blades. As a result, it was concluded that although
the peak efficiency of Wells turbine can be improved by the use of the
proposed 3D blade, its blade does not overcome the weakness of
stalling.