Abstract: The aim of research project is to evaluate quantity and
quality for conjunctive use of groundwater and surface water in lower
in the Lower Nam Kam area, Thailand, even though there have been
hints of saline soil and water. The mathematical model named
WUSMO and MIKE Basin were applied for the calculation of crop
water utilization. Results of the study showed that, in irrigation
command area, water consumption rely on various sources; rain water
21.56%, irrigation water 78.29%, groundwater and some small surface
storage 0.15%. Meanwhile, for non-irrigation command area, water
consumption depends on the Nam Kam and Nambang stream 42%,
rain water 36.75% and groundwater and some small surface storage
19.18%. Samples of surface water and groundwater were collected for
2 seasons. The criterion was determined for the assessment of suitable
water for irrigation. It was found that this area has very limited sources
of suitable water for irrigation.
Abstract: The Boundary Representation of a 3D manifold contains
FACES (connected subsets of a parametric surface S : R2 -!
R3). In many science and engineering applications it is cumbersome
and algebraically difficult to deal with the polynomial set and
constraints (LOOPs) representing the FACE. Because of this reason, a
Piecewise Linear (PL) approximation of the FACE is needed, which is
usually represented in terms of triangles (i.e. 2-simplices). Solving the
problem of FACE triangulation requires producing quality triangles
which are: (i) independent of the arguments of S, (ii) sensitive to the
local curvatures, and (iii) compliant with the boundaries of the FACE
and (iv) topologically compatible with the triangles of the neighboring
FACEs. In the existing literature there are no guarantees for the point
(iii). This article contributes to the topic of triangulations conforming
to the boundaries of the FACE by applying the concept of parameterindependent
Gabriel complex, which improves the correctness of the
triangulation regarding aspects (iii) and (iv). In addition, the article
applies the geometric concept of tangent ball to a surface at a point to
address points (i) and (ii). Additional research is needed in algorithms
that (i) take advantage of the concepts presented in the heuristic
algorithm proposed and (ii) can be proved correct.
Abstract: Most, if not all, public hospitals in Thailand have encountered a common problem regarding the increasing demand for medical services. The increasing number of patients causes so much strain on the hospital-s services, over-crowded, overloaded working hours, staff fatigue, medical error and long waiting time. This research studied the characteristics of operational processes of the medical care services at the medicine department in a large public university hospital. The research focuses on details regarding methods, procedures, processes, resources, and time management in overall processes. The simulation model is used as a tool to analyze the impact of various improvement strategies.
Abstract: Until recently, energy security and climate change
were considered separate issues to be dealt with by policymakers.
The two issues are now converging, challenging the security and
climate communities to develop a better understanding of how to deal
with both issues simultaneously. Although Egypt is not a major
contributor to the world's total GHG emissions, it is particularly
vulnerable to the potential effects of global climate change such as
rising sea levels and changed patterns of rainfall in the Nile Basin.
Climate change is a major threat to sustainable growth and
development in Egypt, and the achievement of the Millennium
Development Goals. Egypt-s capacity to respond to the challenges of
climate instability will be expanded by improving overall resilience,
integrating climate change goals into sustainable development
strategies, increasing the use of modern energy systems with reduced
carbon intensity, and strengthening international initiatives. This
study seeks to establish a framework for considering the complex and
evolving links between energy security and climate change,
applicable to Egypt.
Abstract: In this paper our aim is to explore the construction of schoolgirl femininities, drawing on the results of an ethnographic study conducted in a high school in Ankara, Turkey. In this case study which tries to explore the complexities of gender discourses, we were initially motivated by the questions that have been put forward by critical and feminist literature on education which emphasize the necessarily conflicting and partial nature of both reproduction and resistance and the importance of gendered power relations in the school context. Drawing on this paradigm our research tries to address to a more specific question: how are multiple schoolgirl femininities constructed within the context of gendered school culture, and especially in relation to hegemonic masculinity? Our study reveals that the general framework of multiple femininities is engendered by a tension between two inter-related positions. The first one is different strategies of accommodation and resistance to the gender-related problems of education. The second one is the school experience of girls which is conditioned by their differential position vis-à-vis the masculine resistance culture that is dominant in the school.
Abstract: Impinging jets are used in various industrial areas as a cooling and drying technique. The current research is concerned with the means of improving the heat transfer for configurations with a minimum distance of the nozzle to the impingement surface. The impingement heat transfer is described using numerical methods over a wide range of parameters for an array of planar jets. These parameters include varying jet flow speed, width of nozzle, distance of nozzle, angle of the jet flow, velocity and geometry of the impingement surface. Normal pressure and shear stress are computed as additional parameters. Using dimensionless characteristic numbers the parameters and the results are correlated to gain generalized equations. The results demonstrate the effect of the investigated parameters on the flow.
Abstract: Automatic reading of handwritten cheque is a computationally
complex process and it plays an important role in financial
risk management. Machine vision and learning provide a viable
solution to this problem. Research effort has mostly been focused
on recognizing diverse pitches of cheques and demand drafts with an
identical outline. However most of these methods employ templatematching
to localize the pitches and such schemes could potentially
fail when applied to different types of outline maintained by the
bank. In this paper, the so-called outline problem is resolved by
a cheque information tree (CIT), which generalizes the localizing
method to extract active-region-of-entities. In addition, the weight
based density plot (WBDP) is performed to isolate text entities and
read complete pitches. Recognition is based on texture features using
neural classifiers. Legal amount is subsequently recognized by both
texture and perceptual features. A post-processing phase is invoked
to detect the incorrect readings by Type-2 grammar using the Turing
machine. The performance of the proposed system was evaluated
using cheque and demand drafts of 22 different banks. The test data
consists of a collection of 1540 leafs obtained from 10 different
account holders from each bank. Results show that this approach
can easily be deployed without significant design amendments.
Abstract: Thermal load calculations have been performed for
multi-layered walls that are composed of three different parts; a
common (sand and cement) plaster, and two types of locally
produced soft and hard bricks. The masonry construction of these
layered walls was based on concrete-backed stone masonry made of
limestone bricks joined by mortar. These multilayered walls are
forming the outer walls of the building envelope of a typical Libyan
house. Based on the periodic seasonal weather conditions, within the
Libyan cost region during summer and winter, measured thermal
conductivity values were used to implement such seasonal variation
of heat flow and the temperature variations through the walls. The
experimental measured thermal conductivity values were obtained
using the Hot Disk technique. The estimation of the thermal
resistance of the wall layers ( R-values) is based on measurements
and calculations. The numerical calculations were done using a
simplified analytical model that considers two different wall
constructions which are characteristics of such houses. According to
the obtained results, the R-values were quite low and therefore,
several suggestions have been proposed to improve the thermal
loading performance that will lead to a reasonable human comfort
and reduce energy consumption.
Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: The purpose of this research is to establish the experimental conditions for removal of Cibacron Brilliant Yellow 3G-P dye (CBY) from aqueous solutions by sorption onto coffee husks as a low-cost sorbent. The effects of various experimental parameters (e.g. initial CBY dye concentration, sorbent mass, pH, temperature) were examined and the optimal experimental conditions were determined. The results indicated that the removal of the dye was pH dependent and at initial pH of 2, the dye was removed effectively. The CBY dye sorption data were fitted to Langmuir, Freundlich, Temkin and Dubinin-Radushkevich equilibrium models. The maximum sorption capacity of CBY dye ions onto coffee husks increased from 24.04 to 35.04 mg g-1 when the temperature was increased from 293 to 313 K. The calculated sorption thermodynamic parameters including ΔG°, ΔH°, and ΔS° indicated that the CBY dye sorption onto coffee husks is a spontaneous, endothermic and mainly physical in nature.
Abstract: The necessity of solving multi dimensional
complicated scientific problems beside the necessity of several
objective functions optimization are the most motive reason of born
of artificial intelligence and heuristic methods.
In this paper, we introduce a new method for multiobjective
optimization based on learning automata. In the proposed method,
search space divides into separate hyper-cubes and each cube is
considered as an action. After gathering of all objective functions
with separate weights, the cumulative function is considered as the
fitness function. By the application of all the cubes to the cumulative
function, we calculate the amount of amplification of each action and
the algorithm continues its way to find the best solutions. In this
Method, a lateral memory is used to gather the significant points of
each iteration of the algorithm. Finally, by considering the
domination factor, pareto front is estimated. Results of several
experiments show the effectiveness of this method in comparison
with genetic algorithm based method.
Abstract: This paper is a continuation of our interest in the influence of temperature on specific retention volumes and the resulting infinite dilution activity coefficients. This has a direct effect in the design of absorption and stripping columns for the abatement of volatile organic compounds. The interaction of 13 volatile organic compounds (VOCs) with polydimethylsiloxane (PDMS) at varying temperatures was studied by gas liquid chromatography (GLC). Infinite dilution activity coefficients and specific retention volumes obtained in this study were found to be in agreement with those obtained from static headspace and group contribution methods by the authors as well as literature values for similar systems. Temperature variation also allows for transport calculations for different seasons. The results of this work confirm that PDMS is well suited for the scrubbing of VOCs from waste gas streams. Plots of specific retention volumes against temperature gave linear van-t Hoff plots.
Abstract: The paper provides a literature review of the STEPNC
compliant research around the world. The first part of this paper
focuses on projects based on STEP compliance followed by research
and development in this area based on machining operations. Review
the literature relating to relevant STEP standards and application in
the area of turning centers. This research will review the various
research work, carried out from the evolution of STEP-NC of the
CNC manufacturing activities. The paper concludes with discussion
of the applications in this particular area.
Abstract: Dengue virus is transmitted from person to person
through the biting of infected Aedes Aegypti mosquitoes. DEN-1,
DEN-2, DEN-3 and DEN-4 are four serotypes of this virus. Infection
with one of these four serotypes apparently produces permanent
immunity to it, but only temporary cross immunity to the others. The
length of time during incubation of dengue virus in human and
mosquito are considered in this study. The dengue patients are
classified into infected and infectious classes. The infectious human
can transmit dengue virus to susceptible mosquitoes but infected
human can not. The transmission model of this disease is formulated.
The human population is divided into susceptible, infected, infectious
and recovered classes. The mosquito population is separated into
susceptible, infected and infectious classes. Only infectious
mosquitoes can transmit dengue virus to the susceptible human. We
analyze this model by using dynamical analysis method. The
threshold condition is discussed to reduce the outbreak of this
disease.
Abstract: Many researchers are working on information hiding
techniques using different ideas and areas to hide their secrete data.
This paper introduces a robust technique of hiding secret data in
image based on LSB insertion and RSA encryption technique. The
key of the proposed technique is to encrypt the secret data. Then the
encrypted data will be converted into a bit stream and divided it into
number of segments. However, the cover image will also be divided
into the same number of segments. Each segment of data will be
compared with each segment of image to find the best match
segment, in order to create a new random sequence of segments to be
inserted then in a cover image. Experimental results show that the
proposed technique has a high security level and produced better
stego-image quality.
Abstract: This paper presents the feasibility study of CO2 sequestration from the sources to the sinks in the prospective of Italian Industries. CO2 produced at these sources captured, compressed to supercritical pressures, transported via pipelines and stored in underground geologic formations such as depleted oil and natural gas reservoirs, un-minable coal seams and deep saline aquifers. In this work, we present the optimized pipeline infrastructure for the CO2 with appropriate constraints to find lower cost system by the use of nonlinear optimization software LINGO 11.0. This study was conducted on CO2 transportation complex network of Italian Industries, to find minimum cost network for transporting the CO2 from sources to the sinks.
Abstract: Organizational culture fosters innovation, and
innovation is the main engine to be sustained within the uncertainty
market. Like other countries, the construction industry significantly
contributes to the economy, society and technology of Malaysia, yet,
innovation is still considered slow compared to other industries such
as manufacturing. Given the important role of an architect as the key
player and the contributor of new ideas in the construction industry,
there is a call to identify the issue and improve the current situation
by focusing on the architectural firms. In addition, the existing
studies tend to focus only on a few dimensions of organizational
culture and very few studies consider whether innovation is being
generated or adopted. Hence, the present research tends to fill in the
gap by identifying the organizational cultures that foster or hinder
innovation generation and/or innovation adoption, and propose a
model of organizational culture and innovation generation and/or
adoption.
Abstract: SEMG (Surface Electromyogram) is one of the
bio-signals and is generated from the muscle. And there are many
research results that use forearm EMG to detect hand motions. In this
paper, we will talk about our developed the robot hand system that can
control grasping power by SEMG. In our system, we suppose that
muscle power is proportional to the amplitude of SEMG. The power is
estimated and the grip power of a robot hand is able to be controlled
using estimated muscle power in our system. In addition, to perform a
more precise control can be considered to build a closed loop feedback
system as an object to a subject to pressure from the edge of hand. Our
objectives of this study are the development of a method that makes
perfect detection of the hand grip force possible using SEMG patterns,
and applying this method to the man-machine interface.
Abstract: There are increasingly plagiarism offences for
students in higher education in the digital educational world. On the
other hand, various and competitive online assessment and
plagiarism detection tools are available in the market. Taking the
University of Glamorgan as a case study, this paper describes and
introduces an institutional journey on electronic plagiarism detection
to inform the initial experience of an innovative tool and method
which could be further explored in the future research. The
comparative study and system workflow for e-plagiarism detection
tool are discussed. Benefits for both academics and students are also
presented. Electronic plagiarism detection tools brought great
benefits to both academics and students in Glamorgan. On the other
hand, the debates raised in such initial experience are discussed.
Abstract: The goal of this research is discovering the
determinants of the success or failure of external cooperation in small
and medium enterprises (SMEs). For this, a survey was given to 190
SMEs that experienced external cooperation within the last 3 years. A
logistic regression model was used to derive organizational or strategic
characteristics that significantly influence whether external
collaboration of domestic SMEs is successful or not. Results suggest
that research and development (R&D) features in general
characteristics (both idea creation and discovering market
opportunities) that focused on and emphasized indirected-market
stakeholders (such as complementary companies and affiliates) and
strategies in innovative strategic characteristics raise the probability of
successful external cooperation. This can be used meaningfully to
build a policy or strategy for inducing successful external cooperation
or to understand the innovation of SMEs.