Abstract: A reliable estimate of the average bond stress within
the anchorage of steel reinforcing bars in tension is critically
important for the design of reinforced concrete member. This paper
describes part of a recently completed experimental research program
in the Centre for Infrastructure Engineering and Safety (CIES) at the
University of New South Wales, Sydney, Australia aimed at
assessing the effects of different factors on the anchorage
requirements of modern high strength steel reinforcing bars. The
study found that an increase in the anchorage length and bar diameter
generally leads to a reduction of the average ultimate bond stress. By
the extension of a well established analytical model of bond and
anchorage, it is shown here that the differences in the average
ultimate bond stress for different anchorage lengths is associated with
the variable degree of plastic deformation in the tensile zone of the
concrete surrounding the bar.
Abstract: This study was carried out experimentally and analytically about the performance of solar cell panel system for operating the pump coupled by dc-motor. The solar cell panel with total area 1.9848 m2 consists of three modules of 80 Wp each. The small centrifugal pump powered by dc-motor is operated to lift water from 1m to 7m heads in sequence and gives the amount of water pumped over the whole day from 08.00 to 16.00 h are 11988, 10851, 8874, 7695, 5760, 3600, 2340 L/d respectively. The hourly global solar radiation during the day is an average of 506 W/m2. This study also presents the I-V characteristics of the panel at global radiations 200, 400, 600, 800 and 1000 W/m2 matched with the operation of the pump at the above lifting heads. It proves that the only solar radiations 800 and 1000 W/m2 could provide lifting head from 1m to 7m. The analysis shows the best efficiency point of the performance of solar cell panel system occurs at the pumping head 2.89 m.
Abstract: The game of Maundy Block is the three-player variant
of Maundy Cake, a classical combinatorial game. Even though to
determine the solution of Maundy Cake is trivial, solving Maundy
Block is challenging because of the identification of queer games,
i.e., games where no player has a winning strategy.
Abstract: The main objective of this article is to present the semi-active vibration control using an electro-rheological fluid embedded sandwich structure for a cantilever beam. ER fluid is a smart material, which cause the suspended particles polarize and connect each other to form chain. The stiffness and damping coefficients of the ER fluid can be changed in 10 micro seconds; therefore, ERF is suitable to become the material embedded in the tunable vibration absorber to become a smart absorber. For the ERF smart material embedded structure, the fuzzy control law depends on the experimental expert database and the proposed self-tuning strategy. The electric field is controlled by a CRIO embedded system to implement the real application. This study investigates the different performances using the Type-1 fuzzy and interval Type-2 fuzzy controllers. The Interval type-2 fuzzy control is used to improve the modeling uncertainties for this ERF embedded shock absorber. The self-tuning vibration controllers using Type-1 and Interval Type-2 fuzzy law are implemented to the shock absorber system. Based on the resulting performance, Internal Type-2 fuzzy is better than the traditional Type-1 fuzzy control for this vibration control system.
Abstract: This study examined the effects of two dynamic
visualizations on 60 Malaysian primary school student-s performance
(time on task), retention and transference. The independent variables
in this study were the two dynamic visualizations, the video and the
animated instructions. The dependent variables were the gain score of
performance, retention and transference. The results showed that the
students in the animation group significantly outperformed the
students in the video group in retention. There were no significant
differences in terms of gain scores in the performance and
transference among the animation and the video groups, although the
scores were slightly higher in the animation group compared to the
video group. The conclusion of this study is that the animation
visualization is superior compared to the video in the retention for a
procedural task.
Abstract: Global climate change has become the preeminent
threat to human security in the 21st century. From mitigation perspective, this study aims to evaluate the performance of biogas
renewable project under clean development mechanism activities
(namely Korat-Waste-to-Energy) in Thailand and to assess local perceptions towards the significance of climate change mitigation and
sustainability of such project in their community. Questionnaire was
developed based on the national sustainable development criteria and
was distributed among systematically selected households within
project boundaries (n=260). Majority of the respondents strongly agreed with the reduction of odor problems (81%) and air pollution
(76%). However, they were unsure about greenhouse gas reduction from such project and ignorant about the key issues of climate change. A lesson learned suggested that there is a need to further
investigate the possible socio-psychological barriers may significantly shape public perception and understandings of climate
change in the local context.
Abstract: In this work, we successfully extended one-dimensional differential transform method (DTM), by presenting and proving some theorems, to solving nonlinear high-order multi-pantograph equations. This technique provides a sequence of functions which converges to the exact solution of the problem. Some examples are given to demonstrate the validity and applicability of the present method and a comparison is made with existing results.
Abstract: Dynamic of phytoplankton blooms in the Baltic Sea
has been analyzed applying the numerical ecosystem model 3D
CEMBS. The model consists of the hydrodynamic model (POP,
version 2.1) and the ice model (CICE, version 4.0), which are
imposed by the atmospheric data model (DATM7). The 3D
model has an ecosystem module, activated in 2012 in the operational
mode. The ecosystem model consists of 11 main variables: biomass
of small-size phytoplankton and large-size phytoplankton
and cyanobacteria, zooplankton biomass, dissolved and molecular
detritus, dissolved oxygen concentration, as well as concentrations of
nutrients, including: nitrates, ammonia, phosphates and silicates. The
3D-CEMBS model is an effective tool for solving problems related to
phytoplankton blooms dynamic in the Baltic Sea
Abstract: The aim of this paper is to present the kinematic
analysis and mechanism design of an assistive robotic leg for
hemiplegic and hemiparetic patients. In this work, the priority is to
design and develop the lightweight, effective and single driver
mechanism on the basis of experimental hip and knee angles- data for
walking speed of 1 km/h. A mechanism of cam-follower with three
links is suggested for this purpose. The kinematic analysis is carried
out and analysed using commercialized MATLAB software based on
the prototype-s links sizes and kinematic relationships. In order to
verify the kinematic analysis of the prototype, kinematic analysis data
are compared with the experimental data. A good agreement between
them proves that the anthropomorphic design of the lower extremity
exoskeleton follows the human walking gait.
Abstract: Since 1992, year where Hugo de Garis has published
the first paper on Evolvable Hardware (EHW), a period of intense
creativity has followed. It has been actively researched, developed
and applied to various problems. Different approaches have been
proposed that created three main classifications: extrinsic, mixtrinsic
and intrinsic EHW. Each of these solutions has a real interest.
Nevertheless, although the extrinsic evolution generates some
excellent results, the intrinsic systems are not so advanced. This
paper suggests 3 possible solutions to implement the run-time
configuration intrinsic EHW system: FPGA-based Run-Time
Configuration system, JBits-based Run-Time Configuration system
and Multi-board functional-level Run-Time Configuration system.
The main characteristic of the proposed architectures is that they are
implemented on Field Programmable Gate Array. A comparison of
proposed solutions demonstrates that multi-board functional-level
run-time configuration is superior in terms of scalability, flexibility
and the implementation easiness.
Abstract: In this work, a radial basis function (RBF) neural network is developed for the identification of hyperbolic distributed parameter systems (DPSs). This empirical model is based only on process input-output data and used for the estimation of the controlled variables at specific locations, without the need of online solution of partial differential equations (PDEs). The nonlinear model that is obtained is suitably transformed to a nonlinear state space formulation that also takes into account the model mismatch. A stable robust control law is implemented for the attenuation of external disturbances. The proposed identification and control methodology is applied on a long duct, a common component of thermal systems, for a flow based control of temperature distribution. The closed loop performance is significantly improved in comparison to existing control methodologies.
Abstract: Repeated observation of a given area over time yields
potential for many forms of change detection analysis. These
repeated observations are confounded in terms of radiometric
consistency due to changes in sensor calibration over time,
differences in illumination, observation angles and variation in
atmospheric effects.
This paper demonstrates applicability of an empirical relative
radiometric normalization method to a set of multitemporal cloudy
images acquired by Resourcesat1 LISS III sensor. Objective of this
study is to detect and remove cloud cover and normalize an image
radiometrically. Cloud detection is achieved by using Average
Brightness Threshold (ABT) algorithm. The detected cloud is
removed and replaced with data from another images of the same
area. After cloud removal, the proposed normalization method is
applied to reduce the radiometric influence caused by non surface
factors. This process identifies landscape elements whose reflectance
values are nearly constant over time, i.e. the subset of non-changing
pixels are identified using frequency based correlation technique. The
quality of radiometric normalization is statistically assessed by R2
value and mean square error (MSE) between each pair of analogous
band.
Abstract: Malaria is transmitted to the human by biting of
infected Anopheles mosquitoes. This disease is a serious, acute and
chronic relapsing infection to humans. Fever, nausea, vomiting, back
pain, increased sweating anemia and splenomegaly (enlargement of
the spleen) are the symptoms of the patients who infected with this
disease. It is caused by the multiplication of protozoa parasite of the
genus Plasmodium. Plasmodium falciparum, Plasmodium vivax,
Plasmodium malariae and Plasmodium ovale are the four types of
Plasmodium malaria. A mathematical model for the transmission of
Plasmodium Malaria is developed in which the human and vector
population are divided into two classes, the susceptible and the
infectious classes. In this paper, we formulate the dynamical model
of Plasmodium falciparum and Plasmodium vivax malaria. The
standard dynamical analysis is used for analyzing the behavior for
the transmission of this disease. The Threshold condition is found
and numerical results are shown to confirm the analytical results.
Abstract: The simulation of external aerodynamics is one of the most challenging and important automotive CFD applications. With the rapid developments of digital computers, CFD is used as a practical tool in modern fluid dynamics research. It integrates fluid mechanics disciplines, mathematics and computer science. In this study, two different types of simulations were made, one for the flow around a simplified high speed passenger car with a rear-spoiler and the other for the flow without a rear-spoiler. The standard k-ε model is selected to numerically simulate the external flow field of the simplified Camry model with or without a rear-spoiler. Through an analysis of the simulation results, a new rear spoiler is designed and it shows a mild reduction of the vehicle aerodynamics drag. This leads to less vehicle fuel consumption on the road.
Abstract: In this paper, by using Mawhin-s continuation theorem of coincidence degree and a method based on delay differential inequality, some sufficient conditions are obtained for the existence and global exponential stability of periodic solutions of cellular neural networks with distributed delays and impulses on time scales. The results of this paper generalized previously known results.
Abstract: The process of wafer fabrication is arguably the most
technologically complex and capital intensive stage in semiconductor
manufacturing. This large-scale discrete-event process is highly reentrant,
and involves hundreds of machines, restrictions, and
processing steps. Therefore, production control of wafer fabrication
facilities (fab), specifically scheduling, is one of the most challenging
problems that this industry faces. Dispatching rules have been
extensively applied to the scheduling problems in semiconductor
manufacturing. Moreover, lot release policies are commonly used in
this manufacturing setting to further improve the performance of such
systems and reduce its inherent variability. In this work, simulation is
used in the scheduling of re-entrant flow shop manufacturing systems
with an application in semiconductor wafer fabrication; where, a
simulation model has been developed for the Intel Five-Machine Six
Step Mini-Fab using the ExtendTM simulation environment. The
Mini-Fab has been selected as it captures the challenges involved in
scheduling the highly re-entrant semiconductor manufacturing lines.
A number of scenarios have been developed and have been used to
evaluate the effect of different dispatching rules and lot release
policies on the selected performance measures. Results of simulation
showed that the performance of the Mini-Fab can be drastically
improved using a combination of dispatching rules and lot release
policy.
Abstract: A low cost Short Message System (SMS) based Home security system equipped with motion, smoke, temperature, humidity and light sensors has been studied and tested. The sensors are controlled by a microprocessor PIC 18F4520 through the SMS having password protection code for the secure operation. The user is able to switch light and the appliances and get instant feedback. Also in cases of emergencies such as fire or robbery the system will send alert message to occupant and relevant civil authorities. The operation of the home security has been tested on Vodafone- Fiji network and Digicel Fiji Network for emergency and feedback responses for 25 samples. The experiment showed that it takes about 8-10s for the security system to respond in case of emergency. It takes about 18-22s for the occupant to switch and monitor lights and appliances and then get feedback depending upon the network traffic.
Abstract: The aim of this study was to assess the effect of LAB
isolated from Iranian native olives on the opportunistic skin
pathogens, Pseudomonas aeruginosa and Staphylococcus aureus.
Lactic Acid Bacteria were isolated from the brine of each sample in
the prior of time. The samples were spread on MRS agar for isolation
of lactobacillus and for lactococcus. 28 strains of labs were isolated.
The labs were centrifuged, the supernatant was strewed and pellet
was used to inoculation in wells or at blank disks. 20μl of each pellet
was inoculated to blank disks and 40μl of each pellet was inoculated
to each well. The result of disk and well diffusion agar against these
pathogens were confirmed each other. The size of inhibition zone
was different according to the type of bacteria, the method and the
concentrations of labs.
Abstract: There are reports of gas and oil wells fire due to different accidents. Many different methods are used for fire fighting in gas and oil industry. Traditional fire extinguishing techniques are mostly faced with many problems and are usually time consuming and needs lots of equipments. Besides, they cause damages to facilities, and create health and environmental problems. This article proposes innovative approach in fire extinguishing techniques in oil and gas industry, especially applicable for burning oil wells located offshore. Fire extinguishment employing a turbojet is a novel approach which can help to extinguishment the fire in short period of time. Divergent and convergent turbojets modeled in laboratory scale along with a high pressure flame were used. Different experiments were conducted to determine the relationship between output discharges of trumpet and oil wells. The results were corrected and the relationship between dimensionless parameters of flame and fire extinguishment distances and also the output discharge of turbojet and oil wells in specified distances are demonstrated by specific curves.
Abstract: The modeling of water transfer in the unsaturated zone
uses techniques and methods of the soil physics to solve the
Richards-s equation. However, there is a disaccord between the size
of the measurements provided by the soil physics and the size of the
fields of hydrological modeling problem, to which is added the
strong spatial variability of soil hydraulic properties. The objective of
this work was to develop a methodology to estimate the
hydrodynamic parameters for modeling water transfers at different
hydrological scales in the soil-plant atmosphere systems.