Abstract: In this work we study the reflection of circularly
polarised light from a nano-structured biological material found in
the exocuticle of scarabus beetles. This material is made of a stack
of ultra-thin (~5 nm) uniaxial layers arranged in a left-handed
helicoidal stack, which resonantly reflects circularly polarized light.
A chirp in the layer thickness combined with a finite absorption
coefficient produce a broad smooth reflectance spectrum. By
comparing model calculations and electron microscopy with
measured spectra we can explain our observations and quantify most
relevant structural parameters.
Abstract: Most CT reconstruction system x-ray computed
tomography (CT) is a well established visualization technique in
medicine and nondestructive testing. However, since CT scanning
requires sampling of radiographic projections from different viewing
angles, common CT systems with mechanically moving parts are too
slow for dynamic imaging, for instance of multiphase flows or live
animals. A large number of X-ray projections are needed to
reconstruct CT images, so the collection and calculation of the
projection data consume too much time and harmful for patient. For
the purpose of solving the problem, in this study, we proposed a
method for tomographic reconstruction of a sample from a limited
number of x-ray projections by using linear interpolation method. In
simulation, we presented reconstruction from an experimental x-ray
CT scan of a Aluminum phantom that follows to two steps: X-ray
projections will be interpolated using linear interpolation method and
using it for CT reconstruction based upon Ordered Subsets
Expectation Maximization (OSEM) method.
Abstract: The research study evaluated the performance of
irrigation system by using special scientific tools like Remote
Sensing and GIS technology, so that proper measurements could be
taken for the sustainable agriculture and water management.
Different performance evaluation parameters had been calculated for
the purposed data was gathered from field investigation and different
government and private organizations. According to the calculations,
organic matter ranges from 0.19% (low value) to 0.76% (high value).
In flat irrigation system for wheat yield ranges from 3347.16 to
5260.39 kg/ha, while the total water applied to wheat crop ranges
from 252.94 to 279.19 mm and WUE ranges from 13.07 to 18.37
kg/ha/mm. For rice yield ranges from 3347.47 to 5433.07 kg/ha with
total water supplied to rice crop ranges from 764.71 to 978.15 mm
and WUE ranges from 3.49 to 5.71 kg/ha/mm. Similarly, in raised
bed system wheat yield ranges from 4569.13 to 6008.60 kg/ha, total
water supplied ranges from 158.87 to 185.09 mm and WUE ranges
from 27.20 to 33.54 kg/ha/mm while in rice crop, yield ranges from
5285.04 to 6716.69 kg/ha, total water supplied ranges from 600.72 to
755.06 mm and WUE ranges from 6.41 to 10.05 kg/ha/mm. Almost
51.3% water saving is observed in bed irrigation system as compared
to flat system. Less water supplied to beds is more affective as its
WUE value is higher than flat system where more water is supplied
in both the seasons. Similarly, RWS values show that maximum
water deficit while minimum area is getting adequate water supply.
Greater yield is recorded in bed system as plant per square meter is
more in bed system in comparison of flat system Thus, the integration
of GIS tools to regularly compute performance indices could provide
irrigation managers with the means for managing efficiently the
irrigation system.
Abstract: In very narrow pathways, the speed of sound propagation and the phase of sound waves change due to the air viscosity. We have developed a new finite element method (FEM) that includes the effects of air viscosity for modeling a narrow sound pathway. This method is developed as an extension of the existing FEM for porous sound-absorbing materials. The numerical calculation results for several three-dimensional slit models using the proposed FEM are validated against existing calculation methods.
Abstract: The problem of complex use of water resources in
Central Asia by taking into consideration the sovereignty of the states
and increasing demand on use of water for economic aspects are
considered. Complex program with appropriate mathematical
software intended for calculation of possible variants of using the
Amudarya up-stream water resources according to satisfaction of
incompatible requirements of the national economics in irrigation
and energy generation is proposed.
Abstract: In the present study, the pressure drop and laminar convection heat transfer characteristics of nanofluids in microchannel heat sink with square duct are numerically investigated. The water based nanofluids created with Al2O3 and CuO particles in four different volume fractions of 0%, 0.5%, 1%, 1.5% and 2% are used to analyze their effects on heat transfer and the pressure drop. Under the laminar, steady-state flow conditions, the finite volume method is used to solve the governing equations of heat transfer. Mixture Model is considered to simulate the nanofluid flow. For verification of used numerical method, the results obtained from numerical calculations were compared with the results in literature for both pure water and the nanofluids in different volume fractions. The distributions of the particles in base fluid are assumed to be uniform. The results are evaluated in terms of Nusselt number, the pressure drop and heat transfer enhancement. Analysis shows that the nanofluids enhance heat transfer while the Reynolds number and the volume fractions are increasing. The best overall enhancement was obtained at φ=%2 and Re=100 for CuO-water nanofluid.
Abstract: The state of melt viscosity in injection process is significantly influenced by the setting parameters due to that the shear rate of injection process is higher than other processes. How to determine plastic melt viscosity during injection process is important to understand the influence of setting parameters on the melt viscosity. An apparatus named as pressure sensor bushing (PSB) module that is used to evaluate the melt viscosity during injection process is developed in this work. The formulations to coupling melt viscosity with fill time and injection pressure are derived and then the melt viscosity is determined. A test mold is prepared to evaluate the accuracy on viscosity calculations between the PSB module and the conventional approaches. The influence of melt viscosity on the tensile strength of molded part is proposed to study the consistency of injection quality.
Abstract: The classic problem of recovering arbitrary values of
a band-limited signal from its samples has an added complication
in software radio applications; namely, the resampling calculations
inevitably fold aliases of the analog signal back into the original
bandwidth. The phenomenon is quantified by the spur-free dynamic
range. We demonstrate how a novel application of the Remez (Parks-
McClellan) algorithm permits optimal signal recovery and SFDR, far
surpassing state-of-the-art resamplers.
Abstract: In this study, an optimization of supersonic air-to-air ejector is carried out by a recently developed single-objective genetic algorithm based on adaption of sequence of individuals. Adaptation of sequence is based on Shape-based distance of individuals and embedded micro-genetic algorithm. The optimal sequence found defines the succession of CFD-aimed objective calculation within each generation of regular micro-genetic algorithm. A spring-based deformation mutates the computational grid starting the initial individualvia adapted population in the optimized sequence. Selection of a generation initial individual is knowledge-based. A direct comparison of the newly defined and standard micro-genetic algorithm is carried out for supersonic air-to-air ejector. The only objective is to minimize the loose of total stagnation pressure in the ejector. The result is that sequence-adopted micro-genetic algorithm can provide comparative results to standard algorithm but in significantly lower number of overall CFD iteration steps.
Abstract: Geometry optimizations of metal complexes of Salen(bis(Salicylidene)1,2-ethylenediamine) were carried out at HF and DFT methods employing Lanl2DZ basis set. In this work structural, energies, bond lengths and other physical properties between Mn2+,Cu2+ and Ni2+ ions coordinated by salen–type ligands are examined. All calculations were performed using Gaussian 98W program series. To investigate local aromaticities, NICS were calculated at all centers of rings. The higher the band gap indicating a higher global aromaticity. The possible binding energies have been evaluated. We have evaluated Frequencies and Zero-point energy with freq calculation. The NICS(Nucleous Independent Chemical Shift) Results show Ni(II) complexes are antiaromatic and aromaticites of Mn(II) complexes are larger than Cu(II) complexes. The energy Results show Cu(II) complexes are stability than Mn(II) and Ni(II) complexes.
Abstract: The present paper develops and validates a numerical procedure for the calculation of turbulent combustive flow in converging and diverging ducts and throuh simulation of the heat transfer processes, the amount of production and spread of Nox pollutant has been measured. A marching integration solution procedure employing the TDMA is used to solve the discretized equations. The turbulence model is the Prandtl Mixing Length method. Modeling the combustion process is done by the use of Arrhenius and Eddy Dissipation method. Thermal mechanism has been utilized for modeling the process of forming the nitrogen oxides. Finite difference method and Genmix numerical code are used for numerical solution of equations. Our results indicate the important influence of the limiting diverging angle of diffuser on the coefficient of recovering of pressure. Moreover, due to the intense dependence of Nox pollutant to the maximum temperature in the domain with this feature, the Nox pollutant amount is also in maximum level.
Abstract: The velocity of a moving point in a general path is the vector quantity, which has both magnitude and direction. The magnitude or the direction of the velocity vector can change over time as a result of acceleration that the time rate of velocity changes. Acceleration analysis is important because inertial forces and inertial torques are proportional to rectilinear and angular accelerations accordingly. The loads must be determined in advance to ensure that a machine is adequately designed to handle these dynamic loads. For planar motion, the vector direction of acceleration is commonly separated into two elements: tangential and centripetal or radial components of a point on a rotating body. All textbooks in physics, kinematics and dynamics of machinery consider the magnitude of a radial acceleration at condition when a point rotates with a constant angular velocity and it means without acceleration. The magnitude of the tangential acceleration considered on a basis of acceleration for a rotating point. Such condition of presentation of magnitudes for two components of acceleration logically and mathematically is not correct and may cause further confusion in calculation. This paper presents new analytical expressions of the radial and absolute accelerations of a rotating point with acceleration and covers the gap in theoretical study of acceleration analysis.
Abstract: This work presents the mixed-mode II/III prestressed split-cantilever beam specimen for the fracture testing of composite materials. In accordance with the concept of prestressed composite beams one of the two fracture modes is provided by the prestressed state of the specimen, and the other one is increased up to fracture initiation by using a testing machine. The novel beam-like specimen is able to provide any combination of the mode-II and mode-III energy release rates. A simple closed-form solution is developed using beam theory as a data reduction scheme and for the calculation of the energy release rates in the new configuration. The applicability and the limitations of the novel fracture mechanical test are demonstrated using unidirectional glass/polyester composite specimens. If only crack propagation onset is involved then the mixed-mode beam specimen can be used to obtain the fracture criterion of transparent composite materials in the GII - GIII plane in a relatively simple way.
Abstract: For the communication between human and computer
in an interactive computing environment, the gesture recognition is
studied vigorously. Therefore, a lot of studies have proposed efficient
methods about the recognition algorithm using 2D camera captured
images. However, there is a limitation to these methods, such as the
extracted features cannot fully represent the object in real world.
Although many studies used 3D features instead of 2D features for
more accurate gesture recognition, the problem, such as the processing
time to generate 3D objects, is still unsolved in related researches.
Therefore we propose a method to extract the 3D features combined
with the 3D object reconstruction. This method uses the modified
GPU-based visual hull generation algorithm which disables unnecessary
processes, such as the texture calculation to generate three kinds
of 3D projection maps as the 3D feature: a nearest boundary, a farthest
boundary, and a thickness of the object projected on the base-plane. In
the section of experimental results, we present results of proposed
method on eight human postures: T shape, both hands up, right hand
up, left hand up, hands front, stand, sit and bend, and compare the
computational time of the proposed method with that of the previous
methods.
Abstract: Nowadays there are lots of applications of power and
free conveyors in logistics. They are the most frequently used
conveyor systems worldwide. Overhead conveyor technologies like
power and free systems are used in the most intra-logistics
applications in trade and industry. The automotive, food, beverage
and textile industry as well as aeronautic catering or engineering are
among the applications. Power and free systems employ different
manufacturing intervals in manufacturing as well as in production as
temporary store and buffer. Depending on the application area, power
and free conveyors are equipped with target controls enabling
complex distribution-and sorting tasks. This article introduces a new
power and free conveyor design in intra-logistics and explains its
components. According to the explanation of the components, a
model is created by means of their technical characteristics. Through
the CAD software, the model is visualized. After that, the static
analysis is evaluated. This analysis helps the calculation of the
mandatory state of structures under force action. This powerful model
helps companies achieve lower development costs as well as quicker
market maturity.
Abstract: A theoretical study of the rigidities of slabs with
circular voids oriented in the longitudinal and in the transverse
direction is discussed. Equations are presented for predicting the
bending and torsional rigidities of the voided slabs. This paper
summarizes the results of an extensive literature search and initial
review of the current methods of analyzing voided slab. The various
methods of calculating the equivalent plate parameters, which are
necessary for two-dimensional analysis, are also reviewed. Static
deflections on voided slabs are shown to be in good agreement with
proposed equation.
Abstract: The new idea of analyze of power system failure with
use of artificial neural network is proposed. An analysis of the
possibility of simulating phenomena accompanying system faults and
restitution is described. It was indicated that the universal model for
the simulation of phenomena in whole analyzed range does not exist.
The main classic method of search of optimal structure and
parameter identification are described shortly. The example with
results of calculation is shown.
Abstract: Nowadays, there is little information, concerning the
heat shield systems, and this information is not completely reliable to
use in so many cases. for example, the precise calculation cannot be
done for various materials. In addition, the real scale test has two
disadvantages: high cost and low flexibility, and for each case we
must perform a new test. Hence, using numerical modeling program
that calculates the surface recession rate and interior temperature
distribution is necessary. Also, numerical solution of governing
equation for non-charring material ablation is presented in order to
anticipate the recession rate and the heat response of non-charring
heat shields. the governing equation is nonlinear and the Newton-
Rafson method along with TDMA algorithm is used to solve this
nonlinear equation system. Using Newton- Rafson method for
solving the governing equation is one of the advantages of the
solving method because this method is simple and it can be easily
generalized to more difficult problems. The obtained results
compared with reliable sources in order to examine the accuracy of
compiling code.
Abstract: Recently, bianisotropic media again received
increasing importance in electromagnetic theory because of advances
in material science which enable the manufacturing of complex
bianisotropic materials. By using Maxwell's equations and
corresponding boundary conditions, the electromagnetic field
distribution in bianisotropic solenoid coils is determined and the
influence of the bianisotropic behaviour of coil to the impedance and
Q-factor is considered. Bianisotropic media are the largest class of
linear media which is able to describe the macroscopic material
properties of artificial dielectrics, artificial magnetics, artificial chiral
materials, left-handed materials, metamaterials, and other composite
materials. Several special cases of coils, filled with complex
substance, have been analyzed. Results obtained by using the
analytical approach are compared with values calculated by
numerical methods, especially by our new hybrid EEM/BEM method
and FEM.
Abstract: Current spectrums of a high power induction machine was calculated for the cases of full symmetry, static and dynamic eccentricity. The calculations involve integration of 93 electrical plus four mechanical ordinary differential equations. Electrical equations account for variable inductances affected by slotting and eccentricities. The calculations were followed by Fourier analysis of the stator currents in steady state operation. The paper presents the stator current spectrums in full symmetry, static and dynamic eccentricity cases, and demonstrates the harmonics present in each case. The effect of dynamic eccentricity is demonstrating via comparing the current spectrums related to dynamic eccentricity cases with the full symmetry one. The paper includes one case study, refers to dynamic eccentricity, to present the spectrum of the measured current and demonstrate the existence of the harmonics related to dynamic eccentricity. The zooms of current spectrums around the main slot harmonic zone are included to simplify the comparison and prove the existence of the dynamic eccentricity harmonics in both calculated and measured current spectrums.