Abstract: The incidence of mechanical fracture of an
automobile piston rings prompted development of fracture analysis
method on this case. The three rings (two compression rings and one
oil ring) were smashed into several parts during the power-test (after
manufacturing the engine) causing piston and liner to be damaged.
The radial and oblique cracking happened on the failed piston rings.
The aim of the fracture mechanics simulations presented in this paper
was the calculation of particular effective fracture mechanics
parameters, such as J-integrals and stress intensity factors. Crack
propagation angles were calculated as well. Two-dimensional
fracture analysis of the first compression ring has been developed in
this paper using ABAQUS CAE6.5-1 software. Moreover, SEM
fractography was developed on fracture surfaces and is discussed in
this paper. Results of numerical calculations constitute the basis for
further research on real object.
Abstract: This paper presents the simulation of fragmentation
warhead using a hydrocode, Autodyn. The goal of this research is to
determine the lethal range of such a warhead. This study investigates
the lethal range of warheads with and without steel balls as
preformed fragments. The results from the FE simulation, i.e. initial
velocities and ejected spray angles of fragments, are further processed
using an analytical approach so as to determine a fragment hit density
and probability of kill of a modelled warhead. In order to simulate a
plenty of preformed fragments inside a warhead, the model requires
expensive computation resources. Therefore, this study attempts to
model the problem in an alternative approach by considering an
equivalent mass of preformed fragments to the mass of warhead
casing. This approach yields approximately 7% and 20% difference
of fragment velocities from the analytical results for one and two
layers of preformed fragments, respectively. The lethal ranges of the
simulated warheads are 42.6 m and 56.5 m for warheads with one and
two layers of preformed fragments, respectively, compared to 13.85
m for a warhead without preformed fragment. These lethal ranges are
based on the requirement of fragment hit density. The lethal ranges
which are based on the probability of kill are 27.5 m, 61 m and 70 m
for warheads with no preformed fragment, one and two layers of
preformed fragments, respectively.
Abstract: This paper presents a model for the evaluation of
energy performance and aerodynamic forces acting on a three-bladed
small vertical axis Darrieus wind turbine depending on blade chord
curvature with respect to rotor axis.
The adopted survey methodology is based on an analytical code
coupled to a solid modeling software, capable of generating the
desired blade geometry depending on the blade design geometric
parameters, which is linked to a finite volume CFD code for the
calculation of rotor performance.
After describing and validating the model with experimental data,
the results of numerical simulations are proposed on the bases of two
different blade profile architectures, which are respectively
characterized by a straight chord and by a curved one, having a chord
radius equal to rotor external circumference. A CFD campaign of
analysis is completed for three blade-candidate airfoil sections, that is
the recently-developed DU 06-W-200 cambered blade profile, a
classical symmetrical NACA 0021 and its derived cambered airfoil,
characterized by a curved chord, having a chord radius equal to rotor
external circumference.
The effects of blade chord curvature on angle of attack, blade
tangential and normal forces are first investigated and then the
overall rotor torque and power are analyzed as a function of blade
azimuthal position, achieving a numerical quantification of the
influence of blade camber on overall rotor performance.
Abstract: There are lots of different ways to find the natural
frequencies of a rotating system. One of the most effective methods
which is used because of its precision and correctness is the
application of the transfer matrix. By use of this method the entire
continuous system is subdivided and the corresponding differential
equation can be stated in matrix form. So to analyze shaft that is this
paper issue the rotor is divided as several elements along the shaft
which each one has its own mass and moment of inertia, which this
work would create possibility of defining the named matrix. By
Choosing more elements number, the size of matrix would become
larger and as a result more accurate answers would be earned. In this
paper the dynamics of a rotor-bearing system is analyzed,
considering the gyroscopic effect. To increase the accuracy of
modeling the thickness of the disk and bearings is also taken into
account which would cause more complicated matrix to be solved.
Entering these parameters to our modeling would change the results
completely that these differences are shown in the results. As said
upper, to define transfer matrix to reach the natural frequencies of
probed system, introducing some elements would be one of the
requirements. For the boundary condition of these elements, bearings
at the end of the shaft are modeled as equivalent spring and dampers
for the discretized system. Also, continuous model is used for the
shaft in the system. By above considerations and using transfer
matrix, exact results are taken from the calculations. Results Show
that, by increasing thickness of the bearing the amplitude of vibration
would decrease, but obviously the stiffness of the shaft and the
natural frequencies of the system would accompany growth.
Consequently it is easily understood that ignoring the influences of
bearing and disk thicknesses would results not real answers.
Abstract: The production of devices in nanoscale with specific
molecular rectifying function is one of the most significant goals in
state-of-art technology. In this work we show by ab initio quantum
mechanics calculations coupled with non-equilibrium Green
function, the design of an organic two-terminal device. These
molecular structures have molecular source and drain with several
bridge length (from five up to 11 double bonds). Our results are
consistent with significant features as a molecular rectifier and can be
raised up as: (a) it can be used as bi-directional symmetrical rectifier;
(b) two devices integrated in one (FET with one operational region,
and Thyristor thiristor); (c) Inherent stability due small intrinsic
capacitance under forward/reverse bias. We utilize a scheme for the
transport mechanism based on previous properties of ¤Ç bonds type
that can be successfully utilized to construct organic nanodevices.
Abstract: The amplitude response of infrared (IR) sensors
depends on the reflectance properties of the target. Therefore, in
order to use IR sensor for measuring distances accurately, prior
knowledge of the surface must be known. This paper describes the
Phong Illumination Model for determining the properties of a surface
and subsequently calculating the distance to the surface. The angular
position of the IR sensor is computed as normal to the surface for
simplifying the calculation. Ultrasonic (US) sensor can provide the
initial information on distance to obtain the parameters for this
method. In addition, the experimental results obtained by using
LabView are discussed. More care should be taken when placing the
objects from the sensors during acquiring data since the small change
in angle could show very different distance than the actual one.
Since stereo camera vision systems do not perform well under some
environmental conditions such as plain wall, glass surfaces, or poor
lighting conditions, the IR and US sensors can be used additionally to
improve the overall vision systems of mobile robots.
Abstract: The focus of this research is in the area of the soviet period and the mission of the Russian Orthodox Church in Kazakhstan in the XIX century. There was close connection of national customs and traditions with religious practices, outlooks and attitudes. In particular, such an approach has alleged estimation by Kazakh historians of the process of Christianization of the local population. Some of them are inclined to consider the small number of Christening Kazakhs as evidence that the Russian Orthodox Church didn’t achieve its mission. The number of historians who think that the church didn’t achieve its mission has thousand over the last centuries, however our calculations of the number of Kazakhs who became Orthodox Christian is much more than other historians think. Such Christians can be divided into 3 groups: Some remained Christian until their deaths, others had two faiths and the third hid their true religions, having returned to their former belief. Therefore, to define the exact amount of Christening Kazakhs represented a challenge. Some data does not create a clear picture of the level of Christianization, constant and accurate was not collected. The data appearing in reports of spiritual attendants and civil authorities is not always authentic. Article purpose is illumination and the analysis missionary activity of Russian Orthodox Church in Kazakhstan.
Abstract: In this paper, RSA encryption algorithm and its hardware
implementation in Xilinx-s Virtex Field Programmable Gate
Arrays (FPGA) is analyzed. The issues of scalability, flexible performance,
and silicon efficiency for the hardware acceleration of
public key crypto systems are being explored in the present work.
Using techniques based on the interleaved math for exponentiation,
the proposed RSA calculation architecture is compared to existing
FPGA-based solutions for speed, FPGA utilization, and scalability.
The paper covers the RSA encryption algorithm, interleaved multiplication,
Miller Rabin algorithm for primality test, extended Euclidean
math, basic FPGA technology, and the implementation details of
the proposed RSA calculation architecture. Performance of several
alternative hardware architectures is discussed and compared. Finally,
conclusion is drawn, highlighting the advantages of a fully flexible
& parameterized design.
Abstract: This paper reviews the optimization available
transmission capability (ATC) of power systems using a device of
FACTS named SSSC equipped with energy storage devices. So that,
emplacement and improvement of parameters of SSSC will be
illustrated. Thus, voltage magnitude constraints of network buses,
line transient stability constraints and voltage breakdown constraints
are considered. To help the calculations, a comprehensive program in
DELPHI is provided, which is able to simulate and trace the
parameters of SSSC has been installed on a specific line.
Furthermore, the provided program is able to compute ATC, TTC
and maximum value of their enhancement after using SSSC.
Abstract: If an unsteady heat transfer or heat impulse happens in
part of the cryogenic pipeline system of large space environment
simulation equipment while running in vacuum environment, it will
lead to abnormal flow of the cryogenic fluid in the pipeline. When the
situation gets worse, the cryogenic fluid in the pipeline will have phase
change and a gas block which results in the malfunction of the
cryogenic pipeline system. Referring to the structural parameter of a
typical cryogenic pipeline system and the basic equation, an analytical
model and a calculation model for cryogenic pipeline system can be
built. The various factors which influence the thermal resistance of a
cryogenic pipeline system can be analyzed and calculated by using the
qualitative analysis relation deduced for thermal resistance of pipeline.
The research conclusion could provide theoretical support for the
design and operation of a cryogenic pipeline system
Abstract: The parametrical study of Shrouded Contra-rotating
Rotor was done in this paper based on 2D axisymmetric simulations.
The calculations were made with an actuator disk as double rotor
model. It objects to explore and quantify the effects of different shroud
geometry parameters mainly using the performance of power loading
(PL), which could evaluate the whole propulsion system capability as
5 Newtontotal thrust generationfor hover demand. The numerical
results show that:The increase of nozzle radius is desired but limited
by the flow separation, its optimal design is around 1.15 times rotor
radius, the viscosity effects greatly constraint the influence of nozzle
shape, the divergent angle around 10.5° performs best for chosen
nozzle length;The parameters of inlet such as leading edge curvature,
radius and internal shape do not affect thrust great but play an
important role in pressure distribution which could produce most part
of shroud thrust, they should be chosen according to the reduction of
adverse pressure gradients to reduce the risk of boundary separation.
Abstract: This paper describes a steady state model of a multiple
effect evaporator system for simulation and control purposes. The
model includes overall as well as component mass balance equations,
energy balance equations and heat transfer rate equations for area
calculations for all the effects. Each effect in the process is
represented by a number of variables which are related by the energy
and material balance equations for the feed, product and vapor flow
for backward, mixed and split feed. For simulation 'fsolve' solver in
MATLAB source code is used. The optimality of three sequences i.e.
backward, mixed and splitting feed is studied by varying the various
input parameters.
Abstract: The main purpose of this research is the calculation of implicit prices of the environmental level of air quality in the city of Moscow on the basis of housing property prices. The database used contains records of approximately 20 thousand apartments and has been provided by a leading real estate agency operating in Russia. The explanatory variables include physical characteristics of the houses, environmental (industry emissions), neighbourhood sociodemographic and geographic data: GPS coordinates of each house. The hedonic regression results for ecological variables show «negative» prices while increasing the level of air contamination from such substances as carbon monoxide, nitrogen dioxide, sulphur dioxide, and particles (CO, NO2, SO2, TSP). The marginal willingness to pay for higher environmental quality is presented for linear and log-log models.
Abstract: Mapping between local and global coordinates is an
important issue in finite element method, as all calculations are
performed in local coordinates. The concern arises when subparametric
are used, in which the shape functions of the field variable
and the geometry of the element are not the same. This is particularly
the case for C* elements in which the extra degrees of freedoms
added to the nodes make the elements sub-parametric. In the present
work, transformation matrix for C1* (an 8-noded hexahedron
element with 12 degrees of freedom at each node) is obtained using
equivalent C0 elements (with the same number of degrees of
freedom). The convergence rate of 8-noded C1* element is nearly
equal to its equivalent C0 element, while it consumes less CPU time
with respect to the C0 element. The existence of derivative degrees
of freedom at the nodes of C1* element along with excellent
convergence makes it superior compared with it equivalent C0
element.
Abstract: The design of technological procedures for
manufacturing certain products demands the definition and
optimization of technological process parameters. Their
determination depends on the model of the process itself and its
complexity. Certain processes do not have an adequate mathematical
model, thus they are modeled using heuristic methods. First part of
this paper presents a state of the art of using soft computing
techniques in manufacturing processes from the perspective of
applicability in modern CAx systems. Methods of artificial
intelligence which can be used for this purpose are analyzed. The
second part of this paper shows some of the developed models of
certain processes, as well as their applicability in the actual
calculation of parameters of some technological processes within the
design system from the viewpoint of productivity.
Abstract: Programmable logic controllers are the main controllers in the today's industries; they are used for several applications in industrial control systems and there are lots of examples exist from the PLC applications in industries especially in big companies and plants such as refineries, power plants, petrochemical companies, steel companies, and food and production companies. In the PLCs there are some functions in the function library in software that can be used in PLC programs as basic program elements. The aim of this project are introducing and implementing a new function block of a neural network to the function library of PLC. This block can be applied for some control applications or nonlinear functions calculations after it has been trained for these applications. The implemented neural network is a Perceptron neural network with three layers, three input nodes and one output node. The block can be used in manual or automatic mode. In this paper the structure of the implemented function block, the parameters and the training method of the network are presented by considering the especial method of PLC programming and its complexities. Finally the application of the new block is compared with a classic simulated block and the results are presented.
Abstract: The purpose of this article is to analyze the
degree of concentration in the banking market in EU member
states as well as to determine the impact of the length of EU
membership on the degree of concentration. In that sense
several analysis were conducted, specifically, panel analysis,
calculation of correlation coefficient and regression analysis of
the impact of the length of EU membership on the degree of
concentration. Panel analysis was conducted to determine
whether there is a similar trend of concentration in three
groups of countries - countries with a low, moderate and high
level of concentration. The conducted panel analysis showed
that in EU countries with a moderate level of concentration,
the level of concentration decreases. The calculation of
correlation showed that, to some extent, with other influential
factors, the length of EU membership negatively affects the
market concentration of the banking market. Using the
regression analysis for investigation of the influence of the
length of EU membership on the level of concentration in the
banking sector in a particular country, the results reveal that
there is a negative effect of the length in EU membership on
market concentration, although it is not significantly influential
variable.
Abstract: Delamination between layers in composite materials is a major structural failure. The delamination resistance is quantified by the critical strain energy release rate (SERR). The present investigation deals with the strain energy release rate of two woven fabric composites. Materials used are made of two types of glass fiber (360 gsm and 600 gsm) of plain weave and epoxy as matrix. The fracture behavior is studied using the mode I, double cantilever beam test and the mode II, end notched flexure test, in order to determine the energy required for the initiation and growth of an artificial crack. The delamination energy of these two materials is compared in order to study the effect of weave and reinforcement on mechanical properties. The fracture mechanism is also analyzed by means of scanning electron microscopy (SEM). It is observed that the plain weave fabric composite with lesser strand width has higher inter laminar fracture properties compared to the plain weave fabric composite with more strand width.
Abstract: This paper proposes an active soft-switching circuit for
bridge converters aiming to improve the power conversion efficiency.
The proposed circuit achieves loss-less switching for both main and
auxiliary switches without increasing the main switch current/voltage
rating. A winding coupled to the primary of power transformer
ensures ZCS for the auxiliary switches during their turn-off. A 350 W,
100 kHz phase shifted full bridge (PSFB) converter is built to validate
the analysis and design. Theoretical loss calculations for proposed
circuit is presented. The proposed circuit is compared with passive
soft switched PSFB in terms of efficiency and loss in duty cycle.
Abstract: This paper presents a novel approach for optimal
reconfiguration of radial distribution systems. Optimal
reconfiguration involves the selection of the best set of branches to
be opened, one each from each loop, such that the resulting radial
distribution system gets the desired performance. In this paper an
algorithm is proposed based on simple heuristic rules and identified
an effective switch status configuration of distribution system for the
minimum loss reduction. This proposed algorithm consists of two
parts; one is to determine the best switching combinations in all loops
with minimum computational effort and the other is simple optimum
power loss calculation of the best switching combination found in
part one by load flows. To demonstrate the validity of the proposed
algorithm, computer simulations are carried out on 33-bus system.
The results show that the performance of the proposed method is
better than that of the other methods.