Abstract: The objective of this work which is based on the
approach of simultaneous engineering is to contribute to the
development of a CIM tool for the synthesis of functional design
dimensions expressed by average values and tolerance intervals. In
this paper, the dispersions method known as the Δl method which
proved reliable in the simulation of manufacturing dimensions is
used to develop a methodology for the automation of the simulation.
This methodology is constructed around three procedures. The first
procedure executes the verification of the functional requirements by
automatically extracting the functional dimension chains in the
mechanical sub-assembly. Then a second procedure performs an
optimization of the dispersions on the basis of unknown variables.
The third procedure uses the optimized values of the dispersions to
compute the optimized average values and tolerances of the
functional dimensions in the chains. A statistical and cost based
approach is integrated in the methodology in order to take account of
the capabilities of the manufacturing processes and to distribute
optimal values among the individual components of the chains.
Abstract: In order to compare the performance of the carbon dioxide and HFC-125 heat pumps for medium-and high-temperature heating, both heat pump cycles were optimized using a simulation method. To fairly compare the performance of the cycles by using different working fluids, each cycle was optimized from the viewpoint of heating COP by two design parameters. The first is the gas cooler exit temperature and the other is the ratio of the overall heat conductance of the gas cooler to the combined overall heat conductance of the gas cooler and the evaporator. The inlet and outlet temperatures of secondary fluid of the gas cooler were fixed at 40/90°C and 40/150°C.The results shows that the HFC-125 heat pump has 6% higher heating COP than carbon dioxide heat pump when the heat sink exit temperature is fixed at 90ºC, while the latter outperforms the former when the heat sink exit temperature is fixed at 150ºC under the simulation conditions considered in the present study.
Abstract: Scarcity of water resources and huge costs of
establishing new hydraulic installations necessitate optimal
exploitation from existing reservoirs. Sustainable management and
efficient exploitation from existing finite water resources are
important factors in water resource management, particularly in the
periods of water insufficiency and in dry regions, and on account of
competitive allocations in the view of exploitation management. This
study aims to minimize reservoir water release from a determined
rate of demand. A numerical model for water optimal exploitation
has been developed using GAMS introduced by the World Bank and
applied to the case of Meijaran dam, northern Iran. The results
indicate that this model can optimize the function of reservoir
exploitation while required water for lower parts of the region will be
supplied. Further, allocating optimal water from reservoir, the
optimal rate of water allocated to any group of the users were
specified to increase benefits in curve dam exploitation.
Abstract: In the last decade digital watermarking procedures have
become increasingly applied to implement the copyright protection
of multimedia digital contents distributed on the Internet. To this
end, it is worth noting that a lot of watermarking procedures
for images and videos proposed in literature are based on spread
spectrum techniques. However, some scepticism about the robustness
and security of such watermarking procedures has arisen because
of some documented attacks which claim to render the inserted
watermarks undetectable. On the other hand, web content providers
wish to exploit watermarking procedures characterized by flexible and
efficient implementations and which can be easily integrated in their
existing web services frameworks or platforms. This paper presents
how a simple spread spectrum watermarking procedure for MPEG-2
videos can be modified to be exploited in web contexts. To this end,
the proposed procedure has been made secure and robust against some
well-known and dangerous attacks. Furthermore, its basic scheme
has been optimized by making the insertion procedure adaptive with
respect to the terminals used to open the videos and the network transactions
carried out to deliver them to buyers. Finally, two different
implementations of the procedure have been developed: the former
is a high performance parallel implementation, whereas the latter is
a portable Java and XML based implementation. Thus, the paper
demonstrates that a simple spread spectrum watermarking procedure,
with limited and appropriate modifications to the embedding scheme,
can still represent a valid alternative to many other well-known and
more recent watermarking procedures proposed in literature.
Abstract: Asthma is a condition that causing chronic health problems in children. In addition to basic therapy against disease, we must try to reduce the impact of chronic health problems and also optimize their medical aspect of growth and development. A boy with mild asthma attack frequent episode did not showed any improvement with medical treatment and his asthma control test was 11. From radiologic examination he got hyperaerated lung and billateral sinusitis maxillaris; skin test results were house dust, food and pet allergy; an overweight body; bad school grades; psychological and environmental problem. We followed and evaluated this boy in 6 months, treated holistically. Even we could not do much on environmental but no more psychological and school problems, his on a good bodyweight and his asthma control test was 22. A case of a child with mild asthma attack frequent episode was reported. Asthma clinical course show no significant improvement when other predisposing factor is not well-controlled and a child’s growth and development may be affected. Improving condition of the patient can be created with the help of loving and caring way of nurturing from the parents and supportive peer group. Therefore, continuous and consistent monitoring is required because prognosis of asthma is generally good when regularly and properly controlled.
Abstract: Predictions of flow and heat transfer characteristics and shape optimization in internally finned circular tubes have been performed on three-dimensional periodically fully developed turbulent flow and thermal fields. For a trapezoidal fin profile, the effects of fin height h, upper fin widths d1, lower fin widths d2, and helix angle of fin ? on transport phenomena are investigated for the condition of fin number of N = 30. The CFD and mathematical optimization technique are coupled in order to optimize the shape of internally finned tube. The optimal solutions of the design variables (i.e., upper and lower fin widths, fin height and helix angle) are numerically obtained by minimizing the pressure loss and maximizing the heat transfer rate, simultaneously, for the limiting conditions of d1 = 0.5~1.5 mm, d2 = 0.5~1.5 mm, h= 0.5~1.5mm, ? = 10~30 degrees. The fully developed flow and thermal fields are predicted using the finite volume method and the optimization is carried out by means of the multi-objective genetic algorithm that is widely used in the constrained nonlinear optimization problem.
Abstract: The Institute of Product Development is dealing
with the development, design and dimensioning of micro components
and systems as a member of the Collaborative Research
Centre 499 “Design, Production and Quality Assurance of
Molded micro components made of Metallic and Ceramic Materials".
Because of technological restrictions in the miniaturization
of conventional manufacturing techniques, shape and
material deviations cannot be scaled down in the same proportion
as the micro parts, rendering components with relatively
wide tolerance fields. Systems that include such components
should be designed with this particularity in mind, often requiring
large clearance. On the end, the output of such systems
results variable and prone to dynamical instability. To save
production time and resources, every study of these effects
should happen early in the product development process and
base on computer simulation to avoid costly prototypes. A
suitable method is proposed here and exemplary applied to a
micro technology demonstrator developed by the CRC499. It
consists of a one stage planetary gear train in a sun-planet-ring
configuration, with input through the sun gear and output
through the carrier. The simulation procedure relies on ordinary
Multi Body Simulation methods and subsequently adds
other techniques to further investigate details of the system-s
behavior and to predict its response. The selection of the relevant
parameters and output functions followed the engineering
standards for regular sized gear trains. The first step is to
quantify the variability and to reveal the most critical points of
the system, performed through a whole-mechanism Sensitivity
Analysis. Due to the lack of previous knowledge about the system-s
behavior, different DOE methods involving small and
large amount of experiments were selected to perform the SA.
In this particular case the parameter space can be divided into
two well defined groups, one of them containing the gear-s profile
information and the other the components- spatial location.
This has been exploited to explore the different DOE techniques
more promptly. A reduced set of parameters is derived for
further investigation and to feed the final optimization process,
whether as optimization parameters or as external perturbation
collective. The 10 most relevant perturbation factors and 4 to 6
prospective variable parameters are considered in a new, simplified
model. All of the parameters are affected by the mentioned
production variability. The objective functions of interest
are based on scalar output-s variability measures, so the
problem becomes an optimization under robustness and reliability constrains. The study shows an initial step on the development
path of a method to design and optimize complex micro
mechanisms composed of wide tolerated elements accounting
for the robustness and reliability of the systems- output.
Abstract: Simultaneous Saccharification and Fermentation (SSF) of sugarcane bagasse by cellulase and Pachysolen tannophilus MTCC *1077 were investigated in the present study. Important process variables for ethanol production form pretreated bagasse were optimized using Response Surface Methodology (RSM) based on central composite design (CCD) experiments. A 23 five level CCD experiments with central and axial points was used to develop a statistical model for the optimization of process variables such as incubation temperature (25–45°) X1, pH (5.0–7.0) X2 and fermentation time (24–120 h) X3. Data obtained from RSM on ethanol production were subjected to the analysis of variance (ANOVA) and analyzed using a second order polynomial equation and contour plots were used to study the interactions among three relevant variables of the fermentation process. The fermentation experiments were carried out using an online monitored modular fermenter 2L capacity. The processing parameters setup for reaching a maximum response for ethanol production was obtained when applying the optimum values for temperature (32°C), pH (5.6) and fermentation time (110 h). Maximum ethanol concentration (3.36 g/l) was obtained from 50 g/l pretreated sugarcane bagasse at the optimized process conditions in aerobic batch fermentation. Kinetic models such as Monod, Modified Logistic model, Modified Logistic incorporated Leudeking – Piret model and Modified Logistic incorporated Modified Leudeking – Piret model have been evaluated and the constants were predicted.
Abstract: Over the past decades, automatic face recognition has become a highly active research area, mainly due to the countless application possibilities in both the private as well as the public sector. Numerous algorithms have been proposed in the literature to cope with the problem of face recognition, nevertheless, a group of methods commonly referred to as appearance based have emerged as the dominant solution to the face recognition problem. Many comparative studies concerned with the performance of appearance based methods have already been presented in the literature, not rarely with inconclusive and often with contradictory results. No consent has been reached within the scientific community regarding the relative ranking of the efficiency of appearance based methods for the face recognition task, let alone regarding their susceptibility to appearance changes induced by various environmental factors. To tackle these open issues, this paper assess the performance of the three dominant appearance based methods: principal component analysis, linear discriminant analysis and independent component analysis, and compares them on equal footing (i.e., with the same preprocessing procedure, with optimized parameters for the best possible performance, etc.) in face verification experiments on the publicly available XM2VTS database. In addition to the comparative analysis on the XM2VTS database, ten degraded versions of the database are also employed in the experiments to evaluate the susceptibility of the appearance based methods on various image degradations which can occur in "real-life" operating conditions. Our experimental results suggest that linear discriminant analysis ensures the most consistent verification rates across the tested databases.
Abstract: The overlay approach has been widely used by many service providers for Traffic Engineering (TE) in large Internet backbones. In the overlay approach, logical connections are set up between edge nodes to form a full mesh virtual network on top of the physical topology. IP routing is then run over the virtual network. Traffic engineering objectives are achieved through carefully routing logical connections over the physical links. Although the overlay approach has been implemented in many operational networks, it has a number of well-known scaling issues. This paper proposes a new approach to achieve traffic engineering without full-mesh overlaying with the help of integrated approach and equal subset split method. Traffic engineering needs to determine the optimal routing of traffic over the existing network infrastructure by efficiently allocating resource in order to optimize traffic performance on an IP network. Even though constraint-based routing [1] of Multi-Protocol Label Switching (MPLS) is developed to address this need, since it is not widely tested or debugged, Internet Service Providers (ISPs) resort to TE methods under Open Shortest Path First (OSPF), which is the most commonly used intra-domain routing protocol. Determining OSPF link weights for optimal network performance is an NP-hard problem. As it is not possible to solve this problem, we present a subset split method to improve the efficiency and performance by minimizing the maximum link utilization in the network via a small number of link weight modifications. The results of this method are compared against results of MPLS architecture [9] and other heuristic methods.
Abstract: Factoring Boolean functions is one of the basic operations in algorithmic logic synthesis. A novel algebraic factorization heuristic for single-output combinatorial logic functions is presented in this paper and is developed based on the set theory paradigm. The impact of factoring is analyzed mainly from a low power design perspective for standard cell based digital designs in this paper. The physical implementation of a number of MCNC/IWLS combinational benchmark functions and sub-functions are compared before and after factoring, based on a simple technology mapping procedure utilizing only standard gate primitives (readily available as standard cells in a technology library) and not cells corresponding to optimized complex logic. The power results were obtained at the gate-level by means of an industry-standard power analysis tool from Synopsys, targeting a 130nm (0.13μm) UMC CMOS library, for the typical case. The wire-loads were inserted automatically and the simulations were performed with maximum input activity. The gate-level simulations demonstrate the advantage of the proposed factoring technique in comparison with other existing methods from a low power perspective, for arbitrary examples. Though the benchmarks experimentation reports mixed results, the mean savings in total power and dynamic power for the factored solution over a non-factored solution were 6.11% and 5.85% respectively. In terms of leakage power, the average savings for the factored forms was significant to the tune of 23.48%. The factored solution is expected to better its non-factored counterpart in terms of the power-delay product as it is well-known that factoring, in general, yields a delay-efficient multi-level solution.
Abstract: This paper presents a hybrid electric scooter model developed and simulated using Matlab/Simulink. This hybrid scooter modeled has a parallel hybrid structure. The main propulsion units consist of a two stroke internal combustion engine and a hub motor attached to the front wheel of the scooter. The methodology used to optimize the energy and fuel consumption of the hybrid electric scooter is the multi-mode approach. Various case studies were presented to check the model and were compared to the literatures. Results shown that the model developed was feasible and valuable.
Abstract: Agricultural residue such as oil palm fronds (OPF) is
cheap, widespread and available throughout the year. Hemicelluloses
extracted from OPF can be hydrolyzed to their monomers and used in
production of xylooligosaccharides (XOs). The objective of the
present study was to optimize the enzymatic hydrolysis process of
OPF hemicellulose by varying pH, temperature, enzyme and substrate
concentration for production of XOs. Hemicelluloses was extracted
from OPF by using 3 M potassium hydroxide (KOH) at temperature of
40°C for 4 hrs and stirred at 400 rpm. The hemicellulose was then
hydrolyzed using Trichoderma longibrachiatum xylanase at different
pH, temperature, enzyme and substrate concentration. XOs were
characterized based on reducing sugar determination. The optimum
conditions to produced XOs from OPF hemicellulose was obtained at
pH 4.6, temperature of 40°C , enzyme concentration of 2 U/mL and
2% substrate concentration. The results established the suitability of
oil palm fronds as raw material for production of XOs.
Abstract: We introduce an algorithm based on the
morphological shared-weight neural network. Being nonlinear and
translation-invariant, the MSNN can be used to create better
generalization during face recognition. Feature extraction is
performed on grayscale images using hit-miss transforms that are
independent of gray-level shifts. The output is then learned by
interacting with the classification process. The feature extraction and
classification networks are trained together, allowing the MSNN to
simultaneously learn feature extraction and classification for a face.
For evaluation, we test for robustness under variations in gray levels
and noise while varying the network-s configuration to optimize
recognition efficiency and processing time. Results show that the
MSNN performs better for grayscale image pattern classification
than ordinary neural networks.
Abstract: Applied a mouse-s roller with a gripper to increase the
efficiency for a gripper can learn to a material handling without
slipping. To apply a gripper, we use the optimize principle to develop
material handling by use a signal for checking a roller mouse that
rotate or not. In case of the roller rotates means that the material slips.
A gripper will slide to material handling until the roller will not
rotate. As this experiment has test material handling for comparing a
grip force that uses to material handling of the 10-human with the
applied gripper. We can summarize that human exert the material
handling more than the applied gripper. Because of the gripper can
exert more befit to material handling than human and may be a
minimum force to lift a material without slipping.
Abstract: It is observed that the Weighted least-square (WLS)
technique, including the modifications, results in equiripple error
curve. The resultant error as a percent of the ideal value is highly
non-uniformly distributed over the range of frequencies for which the
differentiator is designed. The present paper proposes a modification
to the technique so that the optimization procedure results in lower
maximum relative error compared to the ideal values. Simulation
results for first order as well as higher order differentiators are given
to illustrate the excellent performance of the proposed method.
Abstract: In this paper, a PSO-based approach is proposed to
derive a digital controller for redesigned digital systems having an interval plant based on resemblance of the extremal gain/phase
margins. By combining the interval plant and a controller as an interval system, extremal GM/PM associated with the loop transfer function
can be obtained. The design problem is then formulated as an optimization problem of an aggregated error function revealing the deviation on the extremal GM/PM between the redesigned digital
system and its continuous counterpart, and subsequently optimized by
a proposed PSO to obtain an optimal set of parameters for the digital controller. Computer simulations have shown that frequency
responses of the redesigned digital system having an interval plant bare a better resemblance to its continuous-time counter part by the incorporation of a PSO-derived digital controller in comparison to those obtained using existing open-loop discretization methods.
Abstract: Increasing energy absorption is a significant parameter
in vehicle design. Absorbing more energy results in decreasing
occupant damage. Limitation of the deflection in a side impact results
in decreased energy absorption (SEA) and increased peak load (PL).
Hence a high crash force jeopardizes passenger safety and vehicle
integrity. The aims of this paper are to determine suitable dimensions
and material of a square beam subjected to side impact, in order to
maximize SEA and minimize PL. To achieve this novel goal, the
geometric parameters of a square beam are optimized using the
response surface method (RSM).multi-objective optimization is
performed, and the optimum design for different response features is
obtained.
Abstract: The dental composites are preferably used as filling
materials due to their esthetic appearances. Nevertheless one of the
major problems, during the application of the dental composites, is
shape change named as “polymerisation shrinkage" affecting clinical
success of the dental restoration while photo-polymerisation.
Polymerisation shrinkage of composites arises basically from the
formation of a polymer due to the monomer transformation which
composes of an organic matrix phase. It was sought, throughout this
study, to detect and evaluate the structural polymerisation shrinkage
of prepared dental composites in order to optimize the effects of
various fillers included in hydroxyapatite (HA)-reinforced dental
composites and hence to find a means to modify the properties of
these dental composites prepared with defined parameters. As a
result, the shrinkage values of the experimental dental composites
were decreased by increasing the filler content of composites and the
composition of different fillers used had effect on the shrinkage of
the prepared composite systems.
Abstract: Nowadays, butyl acetate, a pineapple flavor has been applied widely in food, beverage, cosmetic and pharmaceutical industries. In this study, Butyl acetate, a flavor ester was successfully synthesized via green synthesis of enzymatic reaction route. Commercial immobilized lipase from Rhizomucor miehei (Lipozyme RMIM) was used as biocatalyst in the esterification reaction between acetic acid and butanol. Various reaction parameters such as reaction time (RT), temperature (T) and amount of enzyme (E) were chosen to optimize the reaction synthesis in solvent-free system. The optimum condition to produce butyl acetate was at reaction time (RT), 18 hours; temperature (T), 37°C and amount of enzyme, 25 % (w/w of total substrate). Analysis of yield showed that at optimum condition, >78 % of butyl acetate was produced. The product was confirmed as butyl acetate from FTIR analysis whereby the presence of an ester group was observed at wavenumber of 1742 cm-1.