Abstract: The present study applies the inverse method and
three-dimensional CFD commercial software in conjunction with the
experimental temperature data to investigate the heat transfer and fluid
flow characteristics of the plate-fin heat sink in a rectangular closed
enclosure. The inverse method with the finite difference method and
the experimental temperature data is applied to determine the
approximate heat transfer coefficient. Later, based on the obtained
results, the zero-equation turbulence model is used to obtain the heat
transfer and fluid flow characteristics between two fins. T0 validate
the accuracy of the results obtained, the comparison of the heat transfer
coefficient is made. The obtained temperature at selected
measurement locations of the fin is also compared with experimental
data. The effect of the height of the rectangular enclosure on the
obtained results is discussed.
Abstract: The Northeast China (NEC) was the most important
agriculture areas and known as the Golden-Maize-Belt. Based on
observed crop data and crop model, we design four simulating
experiments and separate relative impacts and contribution under
climate change, planting date shift, and varieties change as well
change of varieties and planting date. Without planting date and
varieties change, maize yields had no significant change trend at
Hailun station located in the north of NEC, and presented significant
decrease by 0.2 - 0.4 t/10a at two stations, which located in the middle
and the south of NEC. With planting date change, yields showed a
significant increase by 0.09 - 0.47 t/10a. With varieties change, maize
yields had significant increase by 1.8~ 1.9 t/10a at Hailun and Huadian
stations, but a non-significant and low increase by 0.2t /10a at Benxi
located in the south of NEC. With change of varieties and planting
date, yields presented a significant increasing by 0.53- 2.0 t/10a. Their
contribution to yields was -25% ~ -55% for climate change, 15% ~
35% for planting date change, and 20% ~110% for varieties change as
well 30% ~135% for varieties with planting date shift. It found that
change in varieties and planting date were highest yields and were
responsible for significant increases in maize yields, varieties was
secondly, and planting date was thirdly. It found that adaptation in
varieties and planting date greatly improved maize yields, and
increased yields annual variability. The increase of contribution with
planting date and varieties change in 2000s was lower than in 1990s.
Yields with the varieties change and yields with planting date and
varieties change all showed a decreasing trend at Huadian and Benxi
since 2002 or so. It indicated that maize yields increasing trend
stagnated in the middle and south of NEC, and continued in the north
of NEC.
Abstract: The composite flour blend consisting of corn, pearl
millet, black gram and wheat bran in the ratio of 80:5:10:5 was taken
to prepare the extruded product and their effect on physical properties
of extrudate was studied. The extrusion process was conducted in
laboratory by using twin screw extruder. The physical characteristics
evaluated include lateral expansion, bulk density, water absorption
index, water solubility index, and rehydration ratio and moisture
retention. The Central Composite Rotatable Design (CCRD) was
used to decide the level of processing variables i.e. feed moisture
content (%), screw speed (rpm), and barrel temperature (oC) for the
experiment. The data obtained after extrusion process were analyzed
by using response surface methodology. A second order polynomial
model for the dependent variables was established to fit the
experimental data. The numerical optimization studies resulted in
127°C of barrel temperature, 246 rpm of screw speed, and 14.5% of
feed moisture as optimum variables to produce acceptable extruded
product. The responses predicted by the software for the optimum
process condition resulted in lateral expansion 126%, bulk density
0.28 g/cm3, water absorption index 4.10 g/g, water solubility index
39.90%, rehydration ratio 544% and moisture retention 11.90% with
75% desirability.
Abstract: In order to help the expert to validate association rules
extracted from data, some quality measures are proposed in the
literature. We distinguish two categories: objective and subjective
measures. The first one depends on a fixed threshold and on data
quality from which the rules are extracted. The second one consists
on providing to the expert some tools in the objective to explore and
visualize rules during the evaluation step. However, the number of
extracted rules to validate remains high. Thus, the manually mining
rules task is very hard. To solve this problem, we propose, in this
paper, a semi-automatic method to assist the expert during the
association rule's validation. Our method uses rule-based
classification as follow: (i) We transform association rules into
classification rules (classifiers), (ii) We use the generated classifiers
for data classification. (iii) We visualize association rules with their
quality classification to give an idea to the expert and to assist him
during validation process.
Abstract: In this paper comprehensive studies have been carried
out for the design optimization of a waste heat recovery system for
effectively utilizing the domestic air conditioner heat energy for
producing hot water. Numerical studies have been carried for the
geometry optimization of a waste heat recovery system for domestic
air conditioners. Numerical computations have been carried out using
a validated 2d pressure based, unsteady, 2nd-order implicit, SST k-ω
turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. At identical inflow and boundary
conditions various geometries were tried and effort has been taken for
proposing the best design criteria. Several combinations of pipe line
shapes viz., straight and spiral with different number of coils for the
radiator have been attempted and accordingly the design criteria has
been proposed for the waste heat recovery system design. We have
concluded that, within the given envelope, the geometry optimization
is a meaningful objective for getting better performance of waste heat
recovery system for air conditioners.
Abstract: Background: Muscle Energy Techniques (MET) have
been widely used by manual therapists over the past years, but still
limited research validated its use and there was limited evidence to
substantiate the theories used to explain its effects. Objective: To
investigate the effect of Muscle Energy Technique (MET) on anterior
pelvic tilt in patients with lumbar spondylosis. Design: Randomized
controlled trial. Subjects: Thirty patients with anterior pelvic tilt from
both sexes were involved, aged between 35 to 50 years old and they
were divided into MET and control groups with 15 patients in each.
Methods: All patients received 3sessions/week for 4 weeks where the
study group received MET, Ultrasound and Infrared, and the control
group received U.S and I.R only. Pelvic angle was measured by
palpation meter, pain severity by the visual analogue scale and
functional disabilities by the Oswestry disability index. Results: Both
groups showed significant improvement in all measured variables.
The MET group was significantly better than the control group in
pelvic angle, pain severity, and functional disability as p-value were
(0.001, 0.0001, 0.0001) respectively. Conclusion and implication: the
study group fulfilled greater improvement in all measured variables
than the control group which implies that application of MET in
combination with U.S and I.R were more effective in improving
pelvic tilting angle, pain severity and functional disabilities than
using electrotherapy only.
Abstract: To tackle the air pollution issues, Plug-in Hybrid
Electric Vehicles (PHEVs) are proposed as an appropriate solution.
Charging a large amount of PHEV batteries, if not controlled, would
have negative impacts on the distribution system. The control process
of charging of these vehicles can be centralized in parking lots that
may provide a chance for better coordination than the individual
charging in houses. In this paper, an optimization-based approach is
proposed to determine the optimum PHEV parking capacities in
candidate nodes of the distribution system. In so doing, a profile for
charging and discharging of PHEVs is developed in order to flatten
the network load profile. Then, this profile is used in solving an
optimization problem to minimize the distribution system losses. The
outputs of the proposed method are the proper place for PHEV
parking lots and optimum capacity for each parking. The application
of the proposed method on the IEEE-34 node test feeder verifies the
effectiveness of the method.
Abstract: Typical load-bearing biological materials like bone,
mineralized tendon and shell, are biocomposites made from both
organic (collagen) and inorganic (biomineral) materials. This
amazing class of materials with intrinsic internally designed
hierarchical structures show superior mechanical properties with
regard to their weak components from which they are formed.
Extensive investigations concentrating on static loading conditions
have been done to study the biological materials failure. However,
most of the damage and failure mechanisms in load-bearing
biological materials will occur whenever their structures are exposed
to dynamic loading conditions. The main question needed to be
answered here is: What is the relation between the layout and
architecture of the load-bearing biological materials and their
dynamic behavior? In this work, a staggered model has been
developed based on the structure of natural materials at nanoscale and
Finite Element Analysis (FEA) has been used to study the dynamic
behavior of the structure of load-bearing biological materials to
answer why the staggered arrangement has been selected by nature to
make the nanocomposite structure of most of the biological materials.
The results showed that the staggered structures will efficiently
attenuate the stress wave rather than the layered structure.
Furthermore, such staggered architecture is effectively in charge of
utilizing the capacity of the biostructure to resist both normal and
shear loads. In this work, the geometrical parameters of the model
like the thickness and aspect ratio of the mineral inclusions selected
from the typical range of the experimentally observed feature sizes
and layout dimensions of the biological materials such as bone and
mineralized tendon. Furthermore, the numerical results validated with
existing theoretical solutions. Findings of the present work emphasize
on the significant effects of dynamic behavior on the natural
evolution of load-bearing biological materials and can help scientists
to design bioinspired materials in the laboratories.
Abstract: Sound processing is one the subjects that newly
attracts a lot of researchers. It is efficient and usually less expensive
than other methods. In this paper the flow generated sound is used to
estimate the flow speed of free flows. Many sound samples are
gathered. After analyzing the data, a parameter named wave power is
chosen. For all samples the wave power is calculated and averaged
for each flow speed. A curve is fitted to the averaged data and a
correlation between the wave power and flow speed is found. Test
data are used to validate the method and errors for all test data were
under 10 percent. The speed of the flow can be estimated by
calculating the wave power of the flow generated sound and using the
proposed correlation.
Abstract: The lifetime of a wireless sensor network can be
effectively increased by using scheduling operations. Once the
sensors are randomly deployed, the task at hand is to find the largest
number of disjoint sets of sensors such that every sensor set provides
complete coverage of the target area. At any instant, only one of these
disjoint sets is switched on, while all other are switched off. This
paper proposes a heuristic search method to find the maximum
number of disjoint sets that completely cover the region. A
population of randomly initialized members is made to explore the
solution space. A set of heuristics has been applied to guide the
members to a possible solution in their neighborhood. The heuristics
escalate the convergence of the algorithm. The best solution explored
by the population is recorded and is continuously updated. The
proposed algorithm has been tested for applications which require
sensing of multiple target points, referred to as point coverage
applications. Results show that the proposed algorithm outclasses the
existing algorithms. It always finds the optimum solution, and that
too by making fewer number of fitness function evaluations than the
existing approaches.
Abstract: Lead time is a critical measure of a supply chain's
performance. It impacts both the customer satisfactions as well as the
total cost of inventory. This paper presents the result of a study on the
analysis of the customer order lead-time for a multinational company.
In the study, the lead time was divided into three stages respectively:
order entry, order fulfillment, and order delivery. A sample of size 2,425 order lines was extracted from the
company's records to use for this study. The sample data entails
information regarding customer orders from the time of order entry
until order delivery. Data regarding the lead time of each stage for
different orders were also provided. Summary statistics on lead time
data reveals that about 30% of the orders were delivered later than the
scheduled due date. The result of the multiple linear regression
analysis technique revealed that component type, logistics parameter,
order size and the customer type have significant impacts on lead
time. Data analysis on the stages of lead time indicates that stage 2
consumed over 50% of the lead time. Pareto analysis was made to
study the reasons for the customer order delay in each stage.
Recommendation was given to resolve the problem.
Abstract: Numerical studies have been carried out using a
validated two-dimensional standard k-omega turbulence model for
the design optimization of a thrust vector control system using shock
induced self-impinging supersonic secondary double jet. Parametric
analytical studies have been carried out at different secondary
injection locations to identifying the highest unsymmetrical
distribution of the main gas flow due to shock waves, which produces
a desirable side force more lucratively for vectoring. The results from
the parametric studies of the case on hand reveal that the shock
induced self-impinging supersonic secondary double jet is more
efficient in certain locations at the divergent region of a CD nozzle
than a case with supersonic single jet with same mass flow rate. We
observed that the best axial location of the self-impinging supersonic
secondary double jet nozzle with a given jet interaction angle, built-in
to a CD nozzle having area ratio 1.797, is 0.991 times the primary
nozzle throat diameter from the throat location. We also observed
that the flexible steering is possible after invoking ON/OFF facility to
the secondary nozzles for meeting the onboard mission requirements.
Through our case studies we concluded that the supersonic self-impinging
secondary double jet at predesigned jet interaction angle
and location can provide more flexible steering options facilitating
with 8.81% higher thrust vectoring efficiency than the conventional
supersonic single secondary jet without compromising the payload
capability of any supersonic aerospace vehicle.
Abstract: Background subtraction and temporal difference are
often used for moving object detection in video. Both approaches are
computationally simple and easy to be deployed in real-time image
processing. However, while the background subtraction is highly
sensitive to dynamic background and illumination changes, the
temporal difference approach is poor at extracting relevant pixels of
the moving object and at detecting the stopped or slowly moving
objects in the scene. In this paper, we propose a simple moving object
detection scheme based on adaptive background subtraction and
temporal difference exploiting dynamic background updates. The
proposed technique consists of histogram equalization, a linear
combination of background and temporal difference, followed by the
novel frame-based and pixel-based background updating techniques.
Finally, morphological operations are applied to the output images.
Experimental results show that the proposed algorithm can solve the
drawbacks of both background subtraction and temporal difference
methods and can provide better performance than that of each method.
Abstract: This paper aims to project the construction of a
prototype azimuthal thruster, mounted with materials of low cost and
easy access, testing in a controlled environment to measure their
performance, characteristics and feasibility of future projects. The
construction of the simulation of dynamic positioning software,
responsible for simulating a vessel and reposition it when necessary.
Validation tests were performed in the form of partial or complete
system. These tests validate the system manually or automatically.
The system provides an interface to the user and simulates the
conditions unfavorable positioning of a vessel, accurately calculates
the azimuth angle, the direction of rotation of the helix and the time
that this should be turned on so that the vessel back to position
original. A serial communication connects the Simulation Dynamic
Positioning System with Embedded System causing the usergenerated
data to simulate the DP system arrives in the form of
control signals to the motors of the propellant. This article addresses
issues in the marine industry employees.
Abstract: This paper is focused on the reference current
calculation in the compensation mode of the active DC traction
substations. The so-called p-q theory of the instantaneous reactive
power is used as theoretical foundation. The compensation goal of
total compensation is taken into consideration for the operation under
both sinusoidal and nonsinusoidal voltage conditions, through the
two objectives of unity power factor and perfect harmonic
cancelation. Four blocks of reference current generation implement
the conceived algorithms and they are included in a specific Simulink
library, which is useful in a DSP dSPACE-based platform working
under Matlab/Simulink. The simulation results validate the
correctness of the implementation and fulfillment of the
compensation tasks.
Abstract: An Acoustic Micro-Energy Harvester (AMEH) is
developed to convert wasted acoustical energy into useful electrical
energy. AMEH is mathematically modeled using Lumped Element
Modelling (LEM) and Euler-Bernoulli beam (EBB) modelling. An
experiment is designed to validate the mathematical model and assess
the feasibility of AMEH. Comparison of theoretical and experimental
data on critical parameter value such as Mm, Cms, dm and Ceb showed
the variances are within 1% to 6%, which is reasonably acceptable.
Then, AMEH undergoes bandwidth tuning for performance
optimization. The AMEH successfully produces 0.9V/(m/s^2) and
1.79μW/(m^2/s^4) at 60Hz and 400kΩ resistive load which only
show variances about 7% compared to theoretical data. At 1g and
60Hz resonance frequency, the averaged power output is about
2.2mW which fulfilled a range of wireless sensors and
communication peripherals power requirements. Finally, the design
for AMEH is assessed, validated and deemed as a feasible design.
Abstract: In this paper, the energy saving and human thermal
comfort in a typical office room are investigated. The impact of a
combined system of exhaust inlet air with light slots located at the
ceiling level in a room served by displacement ventilation system is
numerically modelled. Previous experimental data are used to
validate the Computational Fluid Dynamic (CFD) model. A case
study of simulated office room includes two seating occupants, two
computers, two data loggers and four lamps. The combined system is
located at the ceiling level above the heat sources. A new method of
calculation for the cooling coil load in Stratified Air Distribution
(STRAD) system is used in this study. The results show that 47.4%
energy saving of space cooling load can be achieved by combing the
exhaust inlet air with light slots at the ceiling level above the heat
sources.
Abstract: Mustard leaves are rich in folates, vitamin A, K and
B-complex. Mustard greens are low in calories and fats and rich in
dietary fiber. They are rich in potassium, manganese, iron, copper,
calcium, magnesium and low in sodium. It is very rich in antioxidants
and Phytonutrients. For the optimization of process variables
(moisture content and mustard leave powder), the experiments were
conducted according to central composite Face Centered Composite
design of RSM. The mustard leaves powder was replaced with
composite flour (a combination of rice, chickpea and corn in the ratio
of 70:15:15). The extrudate was extruded in a twin screw extruder at
a barrel temperature of 120°C. The independent variables were
mustard leaves powder (2-10 %) and moisture content (12-20 %).
Responses analyzed were bulk density, water solubility index, water
absorption index, lateral expansion, antioxidant activity, total
phenolic content, and overall acceptability. The optimum conditions
obtained were 7.19 g mustard leaves powder in 100g premix having
16.8% moisture content (w.b).
Abstract: This paper presents Carrier Sense Multiple Access
(CSMA) communication models based on SoC design methodology.
Such a model can be used to support the modeling of the complex
wireless communication systems. Therefore, the use of such
communication model is an important technique in the construction
of high-performance communication. SystemC has been chosen
because it provides a homogeneous design flow for complex designs
(i.e. SoC and IP-based design). We use a swarm system to validate
CSMA designed model and to show how advantages of incorporating
communication early in the design process. The wireless
communication created through the modeling of CSMA protocol that
can be used to achieve communication between all the agents and to
coordinate access to the shared medium (channel).
Abstract: Land Use Land Cover (LULC) changes due to human
activities and natural causes have become a major environmental
concern. Assessment of temporal remote sensing data provides
information about LULC impacts on environment. Land Surface
Temperature (LST) is one of the important components for modeling
environmental changes in climatological, hydrological, and
agricultural studies. In this study, LULC changes (September 7, 1984
and July 8, 2014) especially in agricultural lands together with
population changes (1985-2014) and LST status were investigated
using remotely sensed and census data in South Marmara Watershed,
Turkey. LULC changes were determined using Landsat TM and
Landsat OLI data acquired in 1984 and 2014 summers. Six-band TM
and OLI images were classified using supervised classification
method to prepare LULC map including five classes including Forest
(F), Grazing Land (G), Agricultural Land (A), Water Surface (W),
Residential Area-Bare Soil (R-B) classes. The LST image was also
derived from thermal bands of the same dates.
LULC classification results showed that forest areas, agricultural
lands, water surfaces and residential area-bare soils were increased as
65751 ha, 20163 ha, 1924 ha and 20462 ha respectively. In
comparison, a dramatic decrement occurred in grazing land (107985
ha) within three decades. The population increased 29% between
years 1984-2014 in whole study area. Along with the natural causes,
migration also caused this increase since the study area has an
important employment potential. LULC was transformed among the
classes due to the expansion in residential, commercial and industrial
areas as well as political decisions. In the study, results showed that
agricultural lands around the settlement areas transformed to
residential areas in 30 years.
The LST images showed that mean temperatures were ranged
between 26-32°C in 1984 and 27-33°C in 2014. Minimum
temperature of agricultural lands was increased 3°C and reached to
23°C. In contrast, maximum temperature of A class decreased to
41°C from 44°C. Considering temperatures of the 2014 R-B class and
1984 status of same areas, it was seen that mean, min and max
temperatures increased by 2°C.
As a result, the dynamism of population, LULC and LST resulted
in increasing mean and maximum surface temperatures, living
spaces/industrial areas and agricultural lands.