Abstract: We present an analytical model for the calculation of
the sensitivity, the spectral current noise and the detective parameter
for an optically illuminated In0.53Ga0.47As n+nn+ diode. The
photocurrent due to the excess carrier is obtained by solving the
continuity equation. Moreover, the current noise level is evaluated at
room temperature and under a constant voltage applied between the
diode terminals. The analytical calculation of the current noise in the
n+nn+ structure is developed by considering the free carries
fluctuations. The responsivity and the detection parameter are
discussed as functions of the doping concentrations and the emitter
layer thickness in one-dimensional homogeneous n+nn+ structure.
Abstract: In this work, we propose and analyze a model of
Phytoplankton-Zooplankton interaction with harvesting considering
that some species are exploited commercially for food. Criteria for
local stability, instability and global stability are derived and some
threshold harvesting levels are explored to maintain the population
at an appropriate equilibrium level even if the species are exploited
continuously.Further,biological and bionomic equilibria of the system
are obtained and an optimal harvesting policy is also analysed using
the Pantryagin’s Maximum Principle.Finally analytical findings are
also supported by some numerical simulations.
Abstract: Lead being a toxic heavy metal that mankind is
exposed to the highest levels of this metal from environmental
pollutants. A total of 180 Male scalp hair samples were collected
from different environments in Greater Cairo (GC), i.e. industrial,
heavy traffic and rural areas (60 samples from each) having different
activities during the period of, 1/5/2010 to 1/11/2012. Hair samples
were collected during five stages. Data proved that the concentration
of lead in male industrial areas of Cairo ranged between 6.2847 to
19.0432 μg/g, with mean value of 12.3288 μg/g. On the other hand,
lead content of hair samples of residential-traffic areas ranged
between 2.8634 to 16.3311 μg/g with mean value of 9.7552 μg/g.
While lead concentration on the hair of the male residents living in
rural area ranged between 1.0499-9.0402μg/g with mean value of
4.7327 μg/g. The Pb concentration in scalp hair of Cairo residents of
residential-traffic and rural traffic areas was observed to follow the
same pattern. The pattern was that of decrease concentration of
summer and its increase in winter. Then, there was a marked increase
in Pb concentration of summer 2012, and this increase was
significant. These were obviously seen for the residential-traffic and
rural areas residents. Pb pollution in residents of industrial areas
showed the same seasonal pattern, but there was marked to decrease
in Pb concentration of summer 2012, and this decrease was
significant. Lead pollution in residents of GC was serious. It is worth
noting that the atmosphere is still contaminated by lead despite a
decade of using unleaded gasoline. Strong seasonal variation in
higher Pb concentration on winter than in summer was found. Major
contributions to the pollution with Pb could include industry
emissions, motor vehicle emissions and long transported dust from
outside Cairo. More attention should be paid to the reduction of Pb
content of the urban aerosol and to the Pb pollution health.
Abstract: The levels of maximum power density of GSM
signals in the cities of Lagos, Ibadan and Abuja were studied.
Measurements were made with a calibrated hand held spectrum
analyzer 200m away from 271 base stations, at 1.2m to the ground
level. The maximum GSM 900 signal power density was
139.63μW/m2 in Lagos, 162.49μW/m2 in Ibadan and 5411.26μW/m2
in Abuja. Also, the maximum GSM 1800 signal power density was
296.82μW/m2 in Lagos, 116.82μW/m2 in Ibadan and 1263.00μW/m2
in Abuja. The level of power density of GSM 900 and GSM 1800
signals in the cities of Lagos, Ibadan and Abuja are far less than the
recommended value of 4.5W/m2 for GSM 900 and 9.0 W/m2 for
GSM 1800 by the ICNRP guideline. It can be concluded that
exposure to GSM signals in these cities cannot contribute to the
health detriments caused by thermal effects of radiofrequency
radiation.
Abstract: Image spam is a kind of email spam where the spam
text is embedded with an image. It is a new spamming technique
being used by spammers to send their messages to bulk of internet
users. Spam email has become a big problem in the lives of internet
users, causing time consumption and economic losses. The main
objective of this paper is to detect the image spam by using histogram
properties of an image. Though there are many techniques to
automatically detect and avoid this problem, spammers employing
new tricks to bypass those techniques, as a result those techniques are
inefficient to detect the spam mails. In this paper we have proposed a
new method to detect the image spam. Here the image features are
extracted by using RGB histogram, HSV histogram and combination
of both RGB and HSV histogram. Based on the optimized image
feature set classification is done by using k- Nearest Neighbor(k-NN)
algorithm. Experimental result shows that our method has achieved
better accuracy. From the result it is known that combination of RGB
and HSV histogram with k-NN algorithm gives the best accuracy in
spam detection.
Abstract: Now-a-days autonomous mobile robots have found
applications in diverse fields. An autonomous robot system must be
able to behave in an intelligent manner to deal with complex and
changing environment. This work proposes the performance of path
planning and navigation of autonomous mobile robot using
Gravitational Search Algorithm (GSA), Simulated Annealing (SA)
and Particle Swarm optimization (PSO) based intelligent controllers
in an unstructured environment. The approach not only finds a valid
collision free path but also optimal one. The main aim of the work is
to minimize the length of the path and duration of travel from a
starting point to a target while moving in an unknown environment
with obstacles without collision. Finally, a comparison is made
between the three controllers, it is found that the path length and time
duration made by the robot using GSA is better than SA and PSO
based controllers for the same work.
Abstract: The demand of high quality services has fueled
dimensional research and development in wireless communications
and networking. As a result, different wireless technologies like
Wireless LAN, CDMA, GSM, UMTS, MANET, Bluetooth and
satellite networks etc. have emerged in the last two decades. Future
networks capable of carrying multimedia traffic need IP convergence,
portability, seamless roaming and scalability among the existing
networking technologies without changing the core part of the
existing communications networks. To fulfill these goals, the present
networking systems are required to work in cooperation to ensure
technological independence, seamless roaming, high security and
authentication, guaranteed Quality of Services (QoS). In this paper, a
conceptual framework for a cooperative network (CN) is proposed
for integration of heterogeneous existing networks to meet out the
requirements of the next generation wireless networks.
Abstract: This study presents an attempt to evaluate the
antioxidant potential and antimicrobial activity of methanolic extract,
and essential oils prepared from the leaves of sage (Salvia officinalis
L.). The content of polyphenol in the methanolic extracts from the
leaves of Salvia officinalis was determined spectrophotometrically,
calculated as gallic acid and catechin equivalent. The essential oils
and methanol extract were also subjected to screenings for the
evaluation of their antioxidant activities using 2, 2-diphenyl-1-
picrylhydrazyl (DPPH) test. While the plant essential oils showed
only weak antioxidant activities, its methanol extract was
considerably active in DPPH (IC50 = 37.29 μg/ml) test. Appreciable
total polyphenol content (31.25 mg/g) was also detected for the plant
methanol extract as gallic acid equivalent in the Folin–Ciocalteu test.
The plant was also screened for its antimicrobial activity and good to
moderate inhibitions were recorded for its essential oils, and
methanol extracts against most of the tested microorganisms.
The present investigation revealed that this plant had rich source
of antioxidant properties. It is for this reason that sage has found
increasing application in food formulations.
Abstract: The method of introducing the proxy interpretation for
sending and receiving requests increase the capability of the server
and our approach UDIV (User-Data Identity Security) to solve the
data and user authentication without extending size of the data makes
better than hybrid IDS (Intrusion Detection System). And at the same
time all the security stages we have framed have to pass through less
through that minimize the response time of the request. Even though
an anomaly detected, before rejecting it the proxy extracts its identity
to prevent it to enter into system. In case of false anomalies, the
request will be reshaped and transformed into legitimate request for
further response. Finally we are holding the normal and abnormal
requests in two different queues with own priorities.
Abstract: The growth in the volume of text data such as books
and articles in libraries for centuries has imposed to establish
effective mechanisms to locate them. Early techniques such as
abstraction, indexing and the use of classification categories have
marked the birth of a new field of research called "Information
Retrieval". Information Retrieval (IR) can be defined as the task of
defining models and systems whose purpose is to facilitate access to
a set of documents in electronic form (corpus) to allow a user to find
the relevant ones for him, that is to say, the contents which matches
with the information needs of the user.
Most of the models of information retrieval use a specific data
structure to index a corpus which is called "inverted file" or "reverse
index".
This inverted file collects information on all terms over the corpus
documents specifying the identifiers of documents that contain the
term in question, the frequency of each term in the documents of the
corpus, the positions of the occurrences of the word...
In this paper we use an oriented object database (db4o) instead of
the inverted file, that is to say, instead to search a term in the inverted
file, we will search it in the db4o database.
The purpose of this work is to make a comparative study to see if
the oriented object databases may be competing for the inverse index
in terms of access speed and resource consumption using a large
volume of data.
Abstract: The study is devoted to define the optimal conditions
for the nitriding of pure iron at atmospheric pressure by using NH3-
Ar-C3H8 gas mixtures. After studying the mechanisms of phase
formation and mass transfer at the gas-solid interface, a mathematical
model is developed in order to predict the nitrogen transfer rate in the
solid, the ε-carbonitride layer growth rate and the nitrogen and
carbon concentration profiles. In order to validate the model and to
show its possibilities, it is compared with thermogravimetric
experiments, analyses and metallurgical observations (X-ray
diffraction, optical microscopy and electron microprobe analysis).
Results obtained allow us to demonstrate the sound correlation
between the experimental results and the theoretical predictions.
Abstract: Reburning is a useful technology in reducing nitric
oxide through injection of a secondary hydrocarbon fuel. In this paper,
an experimental study has been conducted to evaluate the effect of fuel
lean reburning on NOx/CO reduction in LNG flame. Experiments
were performed in flames stabilized by a co-flow swirl burner, which
was mounted at the bottom of the furnace. Tests were conducted using
LNG gas as the reburn fuel as well as the main fuel. The effects of
reburn fuel fraction and injection manner of the reburn fuel were
studied when the fuel lean reburning system was applied. The paper
reports data on flue gas emissions and temperature distribution in the
furnace for a wide range of experimental conditions. At steady state,
temperature distribution and emission formation in the furnace have
been measured and compared. This paper makes clear that in order to
decrease both NOx and CO concentrations in the exhaust when the
pulsated fuel lean reburning system was adapted, it is important that
the control of some factors such as frequency and duty ratio. Also it
shows the fuel lean reburning is also effective method to reduce NOx
as much as reburning.
Abstract: The effect of a 3-dimensional (3D) blade on the turbine
characteristics of Wells turbine for wave energy conversion has been
investigated experimentally by model testing under steady flow
conditions in this study, in order to improve the peak efficiency and
stall characteristics. The aim of use of 3D blade is to prevent flow
separation on the suction surface near the tip. The chord length is
constant with radius and the blade profile changes gradually from the
mean radius to tip. The proposed blade profiles in the study are
NACA0015 from the hub to mean radius and NACA0025 at the tip.
The performances of Wells turbine with 3D blades has been compared
with those of the original Wells turbine, i.e., the turbine with
2-dimensional (2D) blades. As a result, it was concluded that although
the peak efficiency of Wells turbine can be improved by the use of the
proposed 3D blade, its blade does not overcome the weakness of
stalling.
Abstract: Carbon nanotube is one of the most attractive materials
for the potential applications of nanotechnology due to its excellent
mechanical, thermal, electrical and optical properties. In this paper we
report a supercapacitor made of nickel foil electrodes, coated with
multiwall carbon nanotubes (MWCNTs) thin film using
electrophoretic deposition (EPD) method. Chemical vapor deposition
method was used for the growth of MWCNTs and ethanol was used as
a hydrocarbon source. High graphitic multiwall carbon nanotube was
found at 750oC analyzing by Raman spectroscopy. We observed the
electrochemical performance of supercapacitor by cyclic
voltammetry. The electrodes of supercapacitor fabricated from
MWCNTs exhibit considerably small equivalent series resistance
(ESR), and a high specific power density. Electrophoretic deposition
is an easy method in fabricating MWCNT electrodes for high
performance supercapacitor.
Abstract: In this paper a comprehensive review on various
factory layouts has been carried out for designing a lucrative process
layout for medium scale industries. Industry data base reveals that the
end product rejection rate is on the order of 10% amounting large
profit loss. In order to avoid these rejection rates and to increase the
quality product production an intermediate non-destructive testing
facility (INDTF) has been recommended for increasing the overall
profit. We observed through detailed case studies that while
introducing INDTF to medium scale industries the expensive
production process can be avoided to the defective products well
before its final shape. Additionally, the defective products identified
during the intermediate stage can be effectively utilized for other
applications or recycling; thereby the overall wastage of the raw
materials can be reduced and profit can be increased. We concluded
that the prudent design of a factory layout through critical path
method facilitating with INDTF will warrant profitable outcome.
Abstract: This paper reports a structured literature review of the
application of Health Information Technology in developing
countries, defined as the World Bank categories Low-income
countries, Lower-middle-income, and Upper-middle-income
countries. The aim was to identify and classify the various
applications of health information technology to assess its current
state in developing countries and explore potential areas of research.
We offer specific analysis and application of HIT in Libya as one of
the developing countries. A structured literature review was
conducted using the following online databases: IEEE, Science
Direct, PubMed, and Google Scholar. Publication dates were set for
2000-2013. For the PubMed search, publications in English, French,
and Arabic were specified. Using a content analysis approach, 159
papers were analyzed and a total number of 26 factors were identified
that affect the adoption of health information technology. Of the 2681
retrieved articles, 159 met the inclusion criteria which were carefully
analyzed and classified. The implementation of health information
technology across developing countries is varied. Whilst it was
initially expected financial constraints would have severely limited
health information technology implementation, some developing
countries like India have nevertheless dominated the literature and
taken the lead in conducting scientific research. Comparing the
number of studies to the number of countries in each category, we
found that Low-income countries and Lower-middle-income had
more studies carried out than Upper-middle-income countries.
However, whilst IT has been used in various sectors of the economy,
the healthcare sector in developing countries is still failing to benefit
fully from the potential advantages that IT can offer.
Abstract: Enterprise Architecture (EA) is employed by
enterprises for providing integrated Information Systems (ISs) in
order to support alignment of their business and Information
Technology (IT). Evaluation of EA implementation can support
enterprise to reach intended goals. There are some problems in
current evaluation methods of EA implementation that lead to
ineffectiveness implementation of EA. This paper represents current
issues on evaluation of EA implementation. In this regard, we set the
framework in order to represent evaluation’s issues based on their
functionality and structure. The results of this research not only
increase the knowledge of evaluation, but also could be useful for
both academics and practitioners in order to realize the current
situation of evaluations.
Abstract: The inspection of underneath vehicle system has been
given significant attention by governments after the threat of
terrorism become more prevalent. New technologies such as mobile
robots and computer vision are led to have more secure environment.
This paper proposed that a mobile robot like Aria robot can be used
to search and inspect the bombs under parking a lot vehicle. This
robot is using fuzzy logic and subsumption algorithms to control the
robot that movies underneath the vehicle. An OpenCV library and
laser Hokuyo are added to Aria robot to complete the experiment for
under vehicle inspection. This experiment was conducted at the
indoor environment to demonstrate the efficiency of our methods to
search objects and control the robot movements under vehicle. We
got excellent results not only by controlling the robot movement but
also inspecting object by the robot camera at same time. This success
allowed us to know the requirement to construct a new cost effective
robot with more functionality.
Abstract: Brown seaweeds are abundant in Portuguese coastline
and represent an almost unexploited marine economic resource. One
of the most common species, easily available for harvesting in the
northwest coast, is Saccorhiza polyschides grows in the lowest shore
and costal rocky reefs. It is almost exclusively used by local farmers
as natural fertilizer, but contains a substantial amount of valuable
compounds, particularly alginates, natural biopolymers of high
interest for many industrial applications.
Alginates are natural polysaccharides present in cell walls of
brown seaweed, highly biocompatible, with particular properties that
make them of high interest for the food, biotechnology, cosmetics
and pharmaceutical industries. Conventional extraction processes are
based on thermal treatment. They are lengthy and consume high
amounts of energy and solvents. In recent years, microwave-assisted
extraction (MAE) has shown enormous potential to overcome major
drawbacks that outcome from conventional plant material extraction
(thermal and/or solvent based) techniques, being also successfully
applied to the extraction of agar, fucoidans and alginates. In the
present study, acid pretreatment of brown seaweed Saccorhiza
polyschides for subsequent microwave-assisted extraction (MAE) of
alginate was optimized. Seaweeds were collected in Northwest
Portuguese coastal waters of the Atlantic Ocean between May and
August, 2014. Experimental design was used to assess the effect of
temperature and acid pretreatment time in alginate extraction.
Response surface methodology allowed the determination of the
optimum MAE conditions: 40 mL of HCl 0.1 M per g of dried
seaweed with constant stirring at 20ºC during 14h. Optimal acid
pretreatment conditions have enhanced significantly MAE of
alginates from Saccorhiza polyschides, thus contributing for the
development of a viable, more environmental friendly alternative to
conventional processes.
Abstract: The Smart Help for persons with disability (PWD) is a
part of the project SMARTDISABLE which aims to develop relevant
solution for PWD that target to provide an adequate workplace
environment for them. It would support PWD needs smartly through
smart help to allow them access to relevant information and
communicate with other effectively and flexibly, and smart editor
that assist them in their daily work. It will assist PWD in knowledge
processing and creation as well as being able to be productive at the
work place. The technical work of the project involves design of a
technological scenario for the Ambient Intelligence (AmI) - based
assistive technologies at the workplace consisting of an integrated
universal smart solution that suits many different impairment
conditions and will be designed to empower the Physically disabled
persons (PDP) with the capability to access and effectively utilize the
ICTs in order to execute knowledge rich working tasks with
minimum efforts and with sufficient comfort level. The proposed
technology solution for PWD will support voice recognition along
with normal keyboard and mouse to control the smart help and smart
editor with dynamic auto display interface that satisfies the
requirements for different PWD group. In addition, a smart help will
provide intelligent intervention based on the behavior of PWD to
guide them and warn them about possible misbehavior. PWD can
communicate with others using Voice over IP controlled by voice
recognition. Moreover, Auto Emergency Help Response would be
supported to assist PWD in case of emergency. This proposed
technology solution intended to make PWD very effective at the
work environment and flexible using voice to conduct their tasks at
the work environment. The proposed solution aims to provide
favorable outcomes that assist PWD at the work place, with the
opportunity to participate in PWD assistive technology innovation
market which is still small and rapidly growing as well as upgrading
their quality of life to become similar to the normal people at the
workplace. Finally, the proposed smart help solution is applicable in
all workplace setting, including offices, manufacturing, hospital, etc.