Abstract: A cyclostationary Gaussian linearization method is
formulated for investigating the time average response of nonlinear
system under sinusoidal signal and white noise excitation. The
quantitative measure of cyclostationary mean, variance, spectrum of
mean amplitude, and mean power spectral density of noise are
analyzed. The qualitative response behavior of stochastic jump and
bifurcation are investigated. The validity of the present approach in
predicting the quantitative and qualitative statistical responses is
supported by utilizing Monte Carlo simulations. The present analysis
without imposing restrictive analytical conditions can be directly
derived by solving non-linear algebraic equations. The analytical
solution gives reliable quantitative and qualitative prediction of mean
and noise response for the Duffing system subjected to both sinusoidal
signal and white noise excitation.
Abstract: This paper presents a model for a modified T-junction
device for microspheres generation. The numerical model is
developed using a commercial software package: COMSOL
Multiphysics. In order to test the accuracy of the numerical model,
multiple variables, such as the flow rate of cross-flow, fluid properties,
structure, and geometry of the microdevice are applied. The results
from the model are compared with the experimental results in the
diameter of the microsphere generated. The comparison shows a good
agreement. Therefore the model is useful in further optimization of the
device and feedback control of microsphere generation if any.
Abstract: The capability of exploiting the electronic charge and
spin properties simultaneously in a single material has made diluted
magnetic semiconductors (DMS) remarkable in the field of
spintronics. We report the designing of DMS based on zinc-blend
ZnO doped with Cr impurity. The full potential linearized augmented
plane wave plus local orbital FP-L(APW+lo) method in density
functional theory (DFT) has been adapted to carry out these
investigations. For treatment of exchange and correlation energy,
generalized gradient approximations have been used. Introducing Cr
atoms in the matrix of ZnO has induced strong magnetic moment
with ferromagnetic ordering at stable ground state. Cr:ZnO was found
to favor the short range magnetic interaction that
reflect tendency of Cr clustering. The electronic structure of ZnO is
strongly influenced in the presence of Cr impurity atoms where
impurity bands appear in the band gap.
Abstract: Although, lanthanum carbonate has not been approved
by the FDA for treatment of hyperphosphatemia, we prospectively
evaluated the efficacy of the combination of Calcium hydroxyapatite
(CHAp) and Lanthanum Carbonate (LaC) for the treatment of
hyperphosphatemia on mice. CHAp was prepared by co-precipitation
method using Ca(OH)2, H3PO4, NH4OH with calcination at 1200ºC.
Lanthanum carbonate was prepared by chemical method using
NaHCO3 and LaCl3 at low pH environment, below 4.0. The
structures were characterized by FTIR spectra and SEM -EDX
analysis. The study group included 16 subjects-mice divided into four
groups according to the administered substance: lanthanum carbonate
(group A), CHAp (group B), lanthanum carbonate + CHAp (group C)
and salt water (group D). The results indicate a phosphate decrease
when subjects (mice) were treated with CHAp and lanthanum
carbonate (0.5% CMC), in a single dose of 1500 mg/kg. Serum
phosphate concentration decreased [(from 4.5 ± 0.8 mg/dL) to
4.05 ± 0.2 mg/dL), P < 0.01] in group A and in group C (to 3.6
± 0.2 mg/dL) at 12 hours from the administration. The combination
of CHAp and lanthanum carbonate is a suitable regimen for
hyperphosphatemia treatment because it avoids both the
hypercalcemia of CaCO3 and the adverse effects of CHAp.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: The quality and condition of perishable products
delivered to the market and their subsequent selling prices are
directly affected by the care taken during harvesting and handling.
Mechanical injury, in fact, occurs at all stages, from pre-harvest
operations through post-harvest handling, packing and transport to
the market. The main implications of this damage are the reduction of
the product’s quality and economical losses related to the shelf life
diminution. For most perishable products, the shelf life is relatively
short and it is typically dictated by microbial growth related to the
application of dynamic and static loads during transportation. This
paper presents the correlation between vibration levels and
microbiological growth on strawberries and woodland strawberries
and detects the presence of volatile organic compounds (VOC) in
order to develop an intelligent logistic unit capable of monitoring
VOCs using a specific sensor system. Fresh fruits were exposed to
vibrations by means of a vibrating table in a temperature-controlled
environment. Microbiological analyses were conducted on samples,
taken at different positions along the column of the crates. The values
obtained were compared with control samples not exposed to
vibrations and the results show that different positions along the
column influence the development of bacteria, yeasts and filamentous
fungi.
Abstract: The purposes of this study are 1) to study the effects
of participatory error correction process and 2) to find out the
students’ satisfaction of such error correction process. This study is a
Quasi Experimental Research with single group, in which data is
collected 5 times preceding and following 4 experimental studies of
participatory error correction process including providing coded
indirect corrective feedback in the students’ texts with error treatment
activities. Samples include 52 2nd year English Major students,
Faculty of Humanities and Social Sciences, Suan Sunandha Rajabhat
University. Tool for experimental study includes the lesson plan of
the course; Reading and Writing English for Academic Purposes II,
and tools for data collection include 5 writing tests of short texts and
a questionnaire. Based on formative evaluation of the students’
writing ability prior to and after each of the 4 experiments, the
research findings disclose the students’ higher scores with statistical
difference at 0.00. Moreover, in terms of the effect size of such
process, it is found that for mean of the students’ scores prior to and
after the 4 experiments; d equals 0.6801, 0.5093, 0.5071, and 0.5296
respectively. It can be concluded that participatory error correction
process enables all of the students to learn equally well and there is
improvement in their ability to write short texts. Finally the students’
overall satisfaction of the participatory error correction process is in
high level (Mean = 4.39, S.D. = 0.76).
Abstract: Microalgae Meyerella planktonica is a potential
biofuel source because it can grow in bulk in either autotrophic or
heterotrophic condition. However, the quantitative growth of this
algal type is still low as it tends to precipitates on the bottom.
Besides, the lipid concentration is still low when grown in
autotrophic condition. In contrast, heterotrophic condition can
enhance the lipid concentration. The combination of autotrophic
condition and agitation treatment was conducted to increase the
density of the culture. On the other hand, a heterotrophic condition
was set up to raise the lipid production. A two-stage experiment
was applied to increase the density at the first step and to increase
the lipid concentration in the next step. The autotrophic condition
resulted higher density but lower lipid concentration compared to
heterotrophic one. The agitation treatment produced higher density
in both autotrophic and heterotrophic conditions. The two-stage
experiment managed to enhance the density during the autotrophic
stage and the lipid concentration during the heterotrophic stage.
The highest yield was performed by using 0.4% v/v glycerol as a
carbon source (2.9±0.016 x 10^6 cells w/w) attained 7 days after the
heterotrophic stage began. The lipid concentration was stable
starting from day 7.
Abstract: In our research we aimed to test a managerial
approach for the fuzzy front end (FFE) of innovation by creating
controlled experiment/ business case in a breakthrough innovation
development. The experiment was in the sport industry and covered
all aspects of the customer discovery stage from ideation to
prototyping followed by patent application. In the paper we describe
and analyze mile stones, tasks, management challenges, decisions
made to create the break through innovation, evaluate overall
managerial efficiency that was at the considered FFE stage.
We set managerial outcome of the FFE stage as a valid product
concept in hand. In our paper we introduce hypothetical construct
“Q-factor” that helps us in the experiment to distinguish quality of
FFE outcomes.
The experiment simulated for entrepreneur the FFE of innovation
and put on his shoulders responsibility for the outcome of valid
product concept. While developing managerial approach to reach the
outcome there was a decision to look on product concept from the
cognitive psychology and cognitive science point of view. This view
helped us to develop the profile of a person whose projection (mental
representation) of a new product could optimize for a manager or
entrepreneur FFE activities. In the experiment this profile was tested
to develop breakthrough innovation for swimmers. Following the
managerial approach the product concept was created to help
swimmers to feel/sense water. The working prototype was developed
to estimate the product concept validity and value added effect for
customers.
Based on feedback from coachers and swimmers there were strong
positive effect that gave high value for customers, and for the
experiment – the valid product concept being developed by proposed
managerial approach for the FFE.
In conclusions there is a suggestion of managerial approach that
was derived from experiment.
Abstract: Subspace channel estimation methods have been
studied widely, where the subspace of the covariance matrix is
decomposed to separate the signal subspace from noise subspace. The
decomposition is normally done by using either the eigenvalue
decomposition (EVD) or the singular value decomposition (SVD) of
the auto-correlation matrix (ACM). However, the subspace
decomposition process is computationally expensive. This paper
considers the estimation of the multipath slow frequency hopping
(FH) channel using noise space based method. In particular, an
efficient method is proposed to estimate the multipath time delays by
applying multiple signal classification (MUSIC) algorithm which is
based on the null space extracted by the rank revealing LU (RRLU)
factorization. As a result, precise information is provided by the
RRLU about the numerical null space and the rank, (i.e., important
tool in linear algebra). The simulation results demonstrate the
effectiveness of the proposed novel method by approximately
decreasing the computational complexity to the half as compared
with RRQR methods keeping the same performance.
Abstract: Activated carbon is an amorphous carbon chain which
has extremely extended surface area. High surface area of activated
carbon is due to the porous structure. Activated carbon, using a
variety of materials such as coal and cellulosic materials; can be
obtained by both physical and chemical methods. The prepared
activated carbon can be used for decolorize, deodorize and also can
be used for removal of organic and non-organic pollution. In this
study, pomegranate peel was subjected to 800W microwave power
for 1 to 4 minutes. Also fresh pomegranate peel was used for the
reference material. Then ZnCl2 was used for the chemical activation
purpose. After the activation process, activated pomegranate peels
were used for the adsorption of Zn metal (40 ppm) in the waste water.
As a result of the adsorption experiments, removal of heavy metals
ranged from 89% to 85%.
Abstract: The main objective of this paper is to provide a new
methodology for road safety assessment in Oman through the
development of suitable accident prediction models. GLM technique
with Poisson or NBR using SAS package was carried out to develop
these models. The paper utilized the accidents data of 31 un-signalized
T-intersections during three years. Five goodness-of-fit
measures were used to assess the overall quality of the developed
models. Two types of models were developed separately; the flow-based
models including only traffic exposure functions, and the full
models containing both exposure functions and other significant
geometry and traffic variables.
The results show that, traffic exposure functions produced much
better fit to the accident data. The most effective geometric variables
were major-road mean speed, minor-road 85th percentile speed,
major-road lane width, distance to the nearest junction, and right-turn
curb radius.
The developed models can be used for intersection treatment or
upgrading and specify the appropriate design parameters of T-intersections.
Finally, the models presented in this thesis reflect the intersection
conditions in Oman and could represent the typical conditions in
several countries in the middle east area, especially gulf countries.
Abstract: This paper provides a quantitative measure of the
time-varying multiunit neuronal spiking activity using an entropy
based approach. To verify the status embedded in the neuronal activity
of a population of neurons, the discrete wavelet transform (DWT) is
used to isolate the inherent spiking activity of MUA. Due to the
de-correlating property of DWT, the spiking activity would be
preserved while reducing the non-spiking component. By evaluating
the entropy of the wavelet coefficients of the de-noised MUA, a
multiresolution Shannon entropy (MRSE) of the MUA signal is
developed. The proposed entropy was tested in the analysis of both
simulated noisy MUA and actual MUA recorded from cortex in rodent
model. Simulation and experimental results demonstrate that the
dynamics of a population can be quantified by using the proposed
entropy.
Abstract: This study examined how individuals in their
respective teams contributed to innovation performance besides
defining the term of innovation in their own respective views. This
study also identified factors that motivated University staff to
contribute to the innovation products. In addition, it examined
whether there is a significant relationship between professional
training level and the length of service among university staff
towards innovation and to what extent do the two variables
contributed towards innovative products. The significance of this
study is that it revealed the strengths and weaknesses of the
university staff when contributing to innovation performance.
Stratified-random sampling was employed to determine the samples
representing the population of lecturers in the study, involving 123
lecturers in one of the local universities in Malaysia. The method
employed to analyze the data is through categorizing into themes for
the open-ended questions besides using descriptive and inferential
statistics for the quantitative data. This study revealed that two types
of definition for the term “innovation” exist among the university
staff, namely, creation of new product or new approach to do things
as well as value-added creative way to upgrade or improve existing
process and service to be more efficient. This study found that the
most prominent factor that propels them towards innovation is to
improve the product in order to benefit users, followed by selfsatisfaction
and recognition. This implies that the staff in the
organization viewed the creation of innovative products as a process
of growth to fulfill the needs of others and also to realize their
personal potential. This study also found that there was only a
significant relationship between the professional training level and
the length of service of 4 - 6 years among the university staff. The
rest of the groups based on the length of service showed that there
was no significant relationship with the professional training level
towards innovation. Moreover, results of the study on directional
measures depicted that the relationship for the length of service of 4-
6 years with professional training level among the university staff is
quite weak. This implies that good organization management lies on
the shoulders of the key leaders who enlighten the path to be
followed by the staff.
Abstract: In 2010-2011, the research on zooplankton was
conducted in the southern part of the Baltic Sea to determine seasonal
variability in changes occurring throughout the zooplankton in 2010
and 2011, both in the region of Gdańsk Deep, and in the western part
of Gdańsk Bay. The research in the sea showed that the taxonomic
composition of holoplankton in the southern part of the Baltic Sea
was similar to that recorded in this region for many years. The
maximum values of abundance and biomass of zooplankton both in
the Deep and the Bay of Gdańsk were observed in the summer
season. Copepoda dominated in the composition of zooplankton for
almost the entire study period, while rotifers occurred in larger
numbers only in the summer 2010 in the Gdańsk Deep as well as in
May and July 2010 in the western part of Gdańsk Bay, and
meroplankton – in April 2011.
Abstract: The performance of box-type solar cookers has been
reported by several researchers but little attention was paid to the
effect of the type of insulation material on the energy and exergy
efficiency of these cookers. This research aimed at evaluating the
energy and exergy efficiencies of the box-type cookers containing
different insulation materials. Energy and exergy efficiencies of five
box-type solar cookers insulated with maize cob, air (control), maize
husk, coconut coir and polyurethane foam respectively were obtained
over a period of three years. The cookers were evaluated using water
heating test procedures in determining the energy and exergy
analysis. The results were subjected to statistical analysis using
ANOVA. The result shows that the average energy input for the five
solar cookers were: 245.5, 252.2, 248.7, 241.5 and 245.5J
respectively while their respective average energy losses were: 201.2,
212.7, 208.4, 189.1 and 199.8J. The average exergy input for five
cookers were: 228.2, 234.4, 231.1, 224.4 and 228.2J respectively
while their respective average exergy losses were: 223.4, 230.6,
226.9, 218.9 and 223.0J. The energy and exergy efficiency was
highest in the cooker with coconut coir (37.35 and 3.90%
respectively) in the first year but was lowest for air (11 and 1.07%
respectively) in the third year. Statistical analysis showed significant
difference between the energy and exergy efficiencies over the years.
These results reiterate the importance of a good insulating material
for a box-type solar cooker.
Abstract: This paper presents a novel integrated hybrid
approach for fault diagnosis (FD) of nonlinear systems. Unlike most
FD techniques, the proposed solution simultaneously accomplishes
fault detection, isolation, and identification (FDII) within a unified
diagnostic module. At the core of this solution is a bank of adaptive
neural parameter estimators (NPE) associated with a set of singleparameter
fault models. The NPEs continuously estimate unknown
fault parameters (FP) that are indicators of faults in the system. Two
NPE structures including series-parallel and parallel are developed
with their exclusive set of desirable attributes. The parallel scheme is
extremely robust to measurement noise and possesses a simpler, yet
more solid, fault isolation logic. On the contrary, the series-parallel
scheme displays short FD delays and is robust to closed-loop system
transients due to changes in control commands. Finally, a fault
tolerant observer (FTO) is designed to extend the capability of the
NPEs to systems with partial-state measurement.
Abstract: Our globalizing world has become almost a small
village and everyone can access any information at any time.
Everyone lets each other know who does whatever in which place.
We can learn which social events occur in which place in the world.
From the perspective of education, the course notes that a lecturer use
in lessons in a university in any state of America can be examined by
a student studying in a city of Africa or the Far East. This dizzying
communication we have mentioned happened thanks to fast
developments in computer and internet technologies. While these
developments occur in the world, Turkey that has a very large young
population and whose electronic infrastructure rapidly improves has
also been affected by these developments. Nowadays, mobile devices
have become common and thus, it causes to increase data traffic in
social networks. This study was carried out on students in the
different age groups in Selcuk University Vocational School of
Technical Sciences, the Department of Computer Technology.
Students’ opinions about the use of internet and social media were
obtained. The features such as using the Internet and social media
skills, purposes, operating frequency, accessing facilities and tools,
social life and effects on vocational education and so forth were
explored. The positive effects and negative effects of both internet
and social media use on the students in this department and findings
are evaluated from different perspectives and results are obtained. In
addition, relations and differences were found out statistically.
Abstract: Forward Osmosis (FO) polyamide thin-film composite
membranes have been prepared by interfacial polymerization using
commercial UF polyethersulfoneas membrane support. Different
interfacial polymerization times (10s, 30s and 60s) in the organic
solution containing trimesoyl chloride (TMC) at constant m-phenylenediamine
(MPD) concentration (2% w/v) were studied. The
synthesized polyamide membranes then tested for treatment of
natural organic matter (NOM) and compared to commercial Cellulose
TriAcetate (CTA) membrane. It was found that membrane prepared
with higher reaction time (30s and 60s) exhibited better membrane
performance (flux and humic acid removal) over commercial CTA
membrane.
Abstract: In this paper, the effects of fiber types and elevated
temperatures on compressive strength, modulus of rapture and the
bond characteristics of fiber reinforced concretes (FRC) are
presented. By using the three different types of fibers (steel fiber-SF,
polypropylene-PPF and polyvinyl alcohol-PVA), FRC specimens
were produced and exposed to elevated temperatures up to 800 ºC for
1.5 hours. In addition, a plain concrete (without fiber) was produced
and used as a control. Test results obtained showed that the steel fiber
reinforced concrete (SFRC) had the highest compressive strength,
modulus of rapture and bond stress values at room temperatures, the
residual bond, flexural and compressive strengths of both FRC and
plain concrete dropped sharply after exposure to high temperatures.
The results also indicated that the reduction of bond, flexural and
compressive strengths with increasing the exposed temperature was
relatively less for SFRC than for plain, and FRC with PPF and PVA.