Abstract: In this paper, it is aimed to improve autonomous flight
performance of a load-carrying (payload: 3 kg and total: 6kg)
unmanned aerial vehicle (UAV) through active wing and horizontal
tail active morphing and also integrated autopilot system parameters
(i.e. P, I, D gains) and UAV parameters (i.e. extension ratios of wing
and horizontal tail during flight) design. For this purpose, a loadcarrying
UAV (i.e. ZANKA-II) is manufactured in Erciyes
University, College of Aviation, Model Aircraft Laboratory is
benefited. Optimum values of UAV parameters and autopilot
parameters are obtained using a stochastic optimization method.
Using this approach autonomous flight performance of UAV is
substantially improved and also in some adverse weather conditions
an opportunity for safe flight is satisfied. Active morphing and
integrated design approach gives confidence, high performance and
easy-utility request of UAV users.
Abstract: The boundary layer separation and new active flow control of a NACA 0025 airfoil were studied experimentally. This new flow control is sometimes known as a co-flow jet (cfj) airfoil. This paper presents the fluctuating velocity in a wall jet over the co-flow jet airfoil subjected to an adverse pressure gradient and a curved surface. In these results, the fluctuating velocity at the inner part increasing by increased the angle of attack up to 12o and this has due to the jet energized, while the angle of attack 20o has different. The airfoil cord based Reynolds number has 105.
Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: This paper investigates the application of metallic
coatings on high fiber volume fraction carbon/epoxy polymer matrix
composites. For the grip of the metallic layer, a method of modifying
the surface of the composite by introducing a mixture of copper and
steel powder (filler powders) which can reduce the impact of thermal
spray particles. The powder was introduced to the surface at the time
of the forming. Arc spray was used to project the zinc coating layer.
The substrate was grit blasted to avoid poor adherence. The porosity, microstructure, and morphology of layers are
characterized by optical microscopy, SEM and image analysis. The
samples were studied also in terms of hardness and erosion resistance.
This investigation did not reveal any visible evidence damage to the
substrates. The hardness of zinc layer was about 25.94 MPa and the
porosity was around (∼6.70%). The erosion test showed that the zinc
coating improves the resistance to erosion. Based on the results
obtained, we can conclude that thermal spraying allows the production
of protective coating on PMC. Zinc coating has been identified as a
compatible material with the substrate. The filler powders layer
protects the substrate from the impact of hot particles and allows
avoiding the rupture of brittle carbon fibers.
Abstract: The rising demand for format-flexible packaging
machines is caused by current market changes. Increasing the formatflexibility
is a new goal for the packaging machine manufacturers’
product development process. There are no methodical or designorientated
tools for a comprehensive consideration of this target. This
paper defines the term format-flexibility in the context of packaging
machines and shows the state-of-the-art for improving the
changeover of production machines. The requirements for a new
approach and the concept itself will be introduced, and the method
elements will be explained. Finally, the use of the concept and the
result of the development of a format-flexible packaging machine
will be shown.
Abstract: Smart metering and demand response are gaining
ground in industrial and residential applications. Smart Appliances
have been given concern towards achieving Smart home. The success
of Smart grid development relies on the successful implementation of
Information and Communication Technology (ICT) in power sector.
Smart Appliances have been the technology under development and
many new contributions to its realization have been reported in the
last few years. The role of ICT here is to capture data in real time,
thereby allowing bi-directional flow of information/data between
producing and utilization point; that lead a way for the attainment of
Smart appliances where home appliances can communicate between
themselves and provide a self-control (switch on and off) using the
signal (information) obtained from the grid. This paper depicts the
background on ICT for smart appliances paying a particular attention
to the current technology and identifying the future ICT trends for
load monitoring through which smart appliances can be achieved to
facilitate an efficient smart home system which promote demand
response program. This paper grouped and reviewed the recent
contributions, in order to establish the current state of the art and
trends of the technology, so that the reader can be provided with a
comprehensive and insightful review of where ICT for smart
appliances stands and is heading to. The paper also presents a brief
overview of communication types, and then narrowed the discussion
to the load monitoring (Non-intrusive Appliances Load Monitoring
‘NALM’). Finally, some future trends and challenges in the further
development of the ICT framework are discussed to motivate future
contributions that address open problems and explore new
possibilities.
Abstract: The very well-known stacked sets of numbers referred
to as Pascal’s triangle present the coefficients of the binomial
expansion of the form (x+y)n. This paper presents an approach (the
Staircase Horizontal Vertical, SHV-method) to the generalization of
planar Pascal’s triangle for polynomial expansion of the form
(x+y+z+w+r+⋯)n. The presented generalization of Pascal’s triangle
is different from other generalizations of Pascal’s triangles given in
the literature. The coefficients of the generalized Pascal’s triangles,
presented in this work, are generated by inspection, using embedded
Pascal’s triangles. The coefficients of I-variables expansion are
generated by horizontally laying out the Pascal’s elements of (I-1)
variables expansion, in a staircase manner, and multiplying them with
the relevant columns of vertically laid out classical Pascal’s elements,
hence avoiding factorial calculations for generating the coefficients
of the polynomial expansion. Furthermore, the classical Pascal’s
triangle has some pattern built into it regarding its odd and even
numbers. Such pattern is known as the Sierpinski’s triangle. In this
study, a presentation of Sierpinski-like patterns of the generalized
Pascal’s triangles is given. Applications related to those coefficients
of the binomial expansion (Pascal’s triangle), or polynomial
expansion (generalized Pascal’s triangles) can be in areas of
combinatorics, and probabilities.
Abstract: The recent instability in economy was found to be
influencing the situation in Malaysia whether directly or indirectly.
Taking that into consideration, the government needs to find the best
approach to balance its citizen’s socio-economic strata level urgently.
Through education platform is among the efforts planned and acted
upon for the purpose of balancing the effects of the influence,
through the exposure of social entrepreneurial activity towards youth
especially those in higher institution level. Armed with knowledge
and skills that they gained, with the support by entrepreneurial
culture and environment while in campus; indirectly, the students will
lean more on making social entrepreneurship as a career option when
they graduate. Following the issues of marketability and workability
of current graduates that are becoming dire, research involving how
far the willingness of student to create social innovation that
contribute to the society without focusing solely on personal gain is
relevant enough to be conducted. With that, this research is
conducted with the purpose of identifying the level of entrepreneurial
intention and social entrepreneurship among higher institution
students in Malaysia. Stratified random sampling involves 355
undergraduate students from five public universities had been made
as research respondents and data were collected through surveys. The
data was then analyzed descriptively using min score and standard
deviation. The study found that the entrepreneurial intention of higher
education students are on moderate level, however it is the contrary
for social entrepreneurship activities, where it was shown on a high
level. This means that while the students only have moderate level of
willingness to be a social entrepreneur, they are very committed to
created social innovation through the social entrepreneurship
activities conducted. The implication from this study can be
contributed towards the higher institution authorities in prediction the
tendency of student in becoming social entrepreneurs. Thus, the
opportunities and facilities for realizing the courses related to social
entrepreneurship must be created expansively so that the vision of
creating as many social entrepreneurs as possible can be achieved.
Abstract: A university-wide survey to obtain baseline data
regarding the perceptions of key terms related to e-learning and
distance learning among students, faculty and staff was conducted to
help achieve the goals of Princess Nourah bint Abdulrahman
University’s and the Kingdom of Saudi Arabia’s National Center for
e-learning and Distance Learning. This paper comprises a relevant
literature review, the survey methodology, preliminary data analysis,
discussion, and recommendations for further research. The major
findings indicate a deep and wide differentiation of understanding
among users of critical key terms.
Abstract: We present an approach to triangle mesh simplification
designed to be executed on the GPU. We use a quadric error metric
to calculate an error value for each vertex of the mesh and order all
vertices based on this value. This step is followed by the parallel
removal of a number of vertices with the lowest calculated error
values. To allow for the parallel removal of multiple vertices we use
a set of per-vertex boundaries that prevent mesh foldovers even when
simplification operations are performed on neighbouring vertices. We
execute multiple iterations of the calculation of the vertex errors,
ordering of the error values and removal of vertices until either a
desired number of vertices remains in the mesh or a minimum error
value is reached. This parallel approach is used to speed up the
simplification process while maintaining mesh topology and avoiding
foldovers at every step of the simplification.
Abstract: The maintenance of work rolls in hot strip processing
has been lengthy and difficult tasks for hot strip manufacturer
because heavy work rolls have to be taken out of the production line,
which could take hours. One way to increase the time between
maintenance is to improve the effectiveness of the work roll cooling
system such that the wear and tear more slowly occurs, while the
operation cost is kept low. Therefore, this study aims to improve the
work roll cooling system by providing the manufacturer the
relationship between the work-roll temperature reduced by cooling
and the water flow that can help manufacturer determining the more
effective water flow of the cooling system. The relationship is found
using simulation with a systematic process adjustment so that the
satisfying quality of product is achieved. Results suggest that the
manufacturer could reduce the water flow by 9% with roughly the
same performance. With the same process adjustment, the feasibility
of finishing-mill-stand reduction is also investigated. Results suggest
its possibility.
Abstract: Voltage level must be raised in order to deliver the
produced energy to the consumption zones with less loss and less
cost. Power transformers used to raise or lower voltage are important
parts of the energy transmission system. Power transformers used in
switchgear and power generation plants stay in human's intensive
habitat zones as a result of expanding cities. Accordingly, noise
levels produced by power transformers have begun more and more
important and they have established itself as one of the research field.
In this research, the noise cause on transformers has been
investigated, it's causes has been examined and noise measurement
techniques have been introduced. Examples of transformer noise test
results are submitted and precautions to be taken were discussed for
the purpose of decreasing of the noise which will occurred by
transformers.
Abstract: Cloud computing can reduce the start-up expenses of implementing EHR (Electronic Health Records). However, many of the healthcare institutions are yet to implement cloud computing due to the associated privacy and security issues. In this paper, we analyze the challenges and opportunities of implementing cloud computing in healthcare. We also analyze data of over 5000 US hospitals that use Telemedicine applications. This analysis helps to understand the importance of smart phones over the desktop systems in different departments of the healthcare institutions. The wide usage of smartphones and cloud computing allows ubiquitous and affordable access to the health data by authorized persons, including patients and doctors. Cloud computing will prove to be beneficial to a majority of the departments in healthcare. Through this analysis, we attempt to understand the different healthcare departments that may benefit significantly from the implementation of cloud computing.
Abstract: Wireless sensors, also known as wireless sensor nodes,
have been making a significant impact on human daily life. The
Radio Frequency Identification (RFID) and Wireless Sensor Network
(WSN) are two complementary technologies; hence, an integrated
implementation of these technologies expands the overall
functionality in obtaining long-range and real-time information on the
location and properties of objects and people. An approach for
integrating ZigBee and RFID networks is proposed in this paper, to
create an energy-efficient network improved by the benefits of
combining ZigBee and RFID architecture. Furthermore, the
compatibility and requirements of the ZigBee device and
communication links in the typical RFID system which is presented
with the real world experiment on the capabilities of the proposed
RFID system.
Abstract: This paper describes two methods for the reduction of
the peak input current during the boosting of Dickson charge pumps.
Both methods are implemented in the fully integrated Dickson charge
pumps of a high-voltage display driver chip for smart-card
applications. Experimental results reveal good correspondence with
Spice simulations and show a reduction of the peak input current by a
factor of 6 during boosting.
Abstract: E-Learning enables the users to learn at anywhere at
any time. In E-Learning systems, authenticating the E-Learning user
has security issues. The usage of appropriate communication
networks for providing the internet connectivity for E-learning is
another challenge. WiMAX networks provide Broadband Wireless
Access through the Multicast Broadcast Service so these networks
can be most suitable for E-Learning applications. The authentication
of E-Learning user is vulnerable to session hijacking problems. The
repeated authentication of users can be done to overcome these
issues. In this paper, session based Profile Caching Authentication is
proposed. In this scheme, the credentials of E-Learning users can be
cached at authentication server during the initial authentication
through the appropriate subscriber station. The proposed cache based
authentication scheme performs fast authentication by using cached
user profile. Thus, the proposed authentication protocol reduces the
delay in repeated authentication to enhance the security in ELearning.
Abstract: This paper presents the strategic development plan of
winged rockets WIRES (WInged REusable Sounding rocket) aiming
at unmanned suborbital winged rocket for demonstrating future fully
reusable space transportation technologies, such as aerodynamics,
Navigation, Guidance and Control (NGC), composite structure,
propulsion system, and cryogenic tanks etc., by universities in
collaboration with government and industries, as well as the past and
current flight test results.
Abstract: Intellectual capital is one of the most valuable and
important parts of the intangible assets of enterprises especially in
knowledge-based enterprises. With respect to increasing gap between
the market value and the book value of the companies, intellectual
capital is one of the components that can be placed in this gap. This
paper uses the value added efficiency of the three components,
capital employed, human capital and structural capital, to measure the
intellectual capital efficiency of Iranian industries groups, listed in
the Tehran Stock Exchange (TSE), using a 8 years period data set
from 2005 to 2012. In order to analyze the effect of intellectual
capital on the market-to-book value ratio of the companies, the data
set was divided into 10 industries, Banking, Pharmaceutical, Metals
& Mineral Nonmetallic, Food, Computer, Building, Investments,
Chemical, Cement and Automotive, and the panel data method was
applied to estimating pooled OLS. The results exhibited that value
added of capital employed has a positive significant relation with
increasing market value in the industries, Banking, Metals & Mineral
Nonmetallic, Food, Computer, Chemical and Cement, and also,
showed that value added efficiency of structural capital has a positive
significant relation with increasing market value in the Banking,
Pharmaceutical and Computer industries groups. The results of the
value added showed a negative relation with the Banking and
Pharmaceutical industries groups and a positive relation with
computer and Automotive industries groups. Among the studied
industries, computer industry has placed the widest gap between the
market value and book value in its intellectual capital.
Abstract: In this paper, a method has been developed to
construct the membership surfaces of row and column vectors and
arithmetic operations of imprecise matrix. A matrix with imprecise
elements would be called an imprecise matrix. The membership
surface of imprecise vector has been already shown based on
Randomness-Impreciseness Consistency Principle. The Randomness-
Impreciseness Consistency Principle leads to defining a normal law
of impreciseness using two different laws of randomness. In this
paper, the author has shown row and column membership surfaces
and arithmetic operations of imprecise matrix and demonstrated with
the help of numerical example.
Abstract: Pain management is a question of quality of life and
an indicator for nursing quality. Chronic pain which is predominant
in oncology and palliative nursing situations is perceived today as a
multifactorial, individual emotional experience with specific
characteristics including the sociocultural dimension when dealing
with migrant patients. This dimension of chronic pain is of major
importance in professional nursing of migrant patients in hospices or
palliative care units. Objectives of the study are: 1. To find out more
about the sociocultural views on pain and nursing care, on customs
and nursing practices connected with pain of both Turkish Muslim
and German Christian women, 2. To improve individual and family
oriented nursing practice with view to sociocultural needs of patients
in severe pain in palliative care. In a qualitative-explorative comparative study 4 groups of women,
Turkish Muslims immigrants (4 from the first generation, 5 from the
second generation) and German Christian women of two generations
(5 of each age group) of the same age groups as the Turkish women
and with similar educational backgrounds were interviewed (semistructured
ethnographic interviews using Spradley, 1979) on their
perceptions and experiences of pain and nursing care within their
families. For both target groups the presentation will demonstrate the
following results in detail: Utterance of pain as well as “private” and
“public” pain vary within different societies and cultures. Permitted
forms of pain utterance are learned in childhood and determine
attitudes and expectations in adulthood. Language, especially when
metaphors and symbols are used, plays a major role for
misunderstandings. The sociocultural context of illness may include
specific beliefs that are important to the patients and yet seem more
than far-fetched from a biomedical perspective. Pain can be an
influential factor in family relationships where respect or hierarchies
do not allow the direct utterance of individual needs. Specific
resources are often, although not exclusively, linked to religious
convictions and are significantly helpful in reducing pain. The discussion will evaluate the results of the study with view to
the relevant literature and present nursing interventions and
instruments beyond medication that are helpful when dealing with
patients from various socio-cultural backgrounds in painful end-oflife
situations.