Abstract: A comprehensive discussion of feasible strategies for sustainable energy supply is urgently needed to achieve a turnaround of the current energy situation. The necessary fundamentals required for the development of a long term energy vision are lacking to a great extent due to the absence of reasonable long term scenarios that fulfill the requirements of climate protection and sustainable energy use. The contribution of the study is based on a search for sustainable energy paths in the long run for Austria. The analysis makes use of secondary data predominantly. The measures developed to avoid CO2 emissions and other ecological risk factors vary to a great extent among all economic sectors. This is shown by the calculation of CO2 cost of abatement curves. In this study it is demonstrated that the most effective technical measures with the lowest CO2 abatement costs yield solutions to the current energy problems. Various scenarios are presented concerning the question how the technological and environmental options for a sustainable energy system for Austria could look like in the long run. It is shown how sustainable energy can be supplied even with today-s technological knowledge and options available. The scenarios developed include an evaluation of the economic costs and ecological impacts. The results are not only applicable to Austria but demonstrate feasible and cost efficient ways towards a sustainable future.
Abstract: Transpedicular screw fixation in spinal fractures,
degenerative changes, or deformities is a well-established procedure.
However, important rate of fixation failure due to screw bending,
loosening, or pullout are still reported particularly in weak bone stock
in osteoporosis. To overcome the problem, mechanism of failure has
to be fully investigated in vitro. Post-mortem human subjects are less
accessible and animal cadavers comprise limitations due to different
geometry and mechanical properties. Therefore, the development of a
synthetic model mimicking the realistic human vertebra is highly
demanded. A bone surrogate, composed of Polyurethane (PU) foam
analogous to cancellous bone porous structure, was tested for 3
different densities in this study. The mechanical properties were
investigated under uniaxial compression test by minimizing the end
artifacts on specimens. The results indicated that PU foam of 0.32
g.cm-3 density has comparable mechanical properties to human
cancellous bone in terms of young-s modulus and yield strength.
Therefore, the obtained information can be considered as primary
step for developing a realistic cancellous bone of human vertebral
body. Further evaluations are also recommended for other density
groups.
Abstract: Previous research has demonstrated that negative
attitudes towards people with physical disabilities and obesity are
predicted by a component of perceived vulnerability to disease; germ
aversion. These findings have been suggested as illustrations of an
evolved but over-active mechanism which promotes the avoidance of
pathogen-carrying individuals. To date, this interpretation of attitude
formation has not been explored with regard to people with
intellectual disability, and no attempts have been made to examine
possible mediating factors. This study examined attitudes in 333
adults and demonstrated that the moderate positive relationship
between germ aversion and negative attitudes toward people with
intellectual disability is fully mediated by social dominance
orientation, a general preference for hierarchies and inequalities
among social groups. These findings have implications for the
design of programs which attempt to promote community acceptance
and inclusion of people with disabilities.
Abstract: Bond graph models of an electrical transformer including
the nonlinear saturation are presented. The transformer
using electrical and magnetic circuits are modelled. These models
determine the relation between self and mutual inductances, and
the leakage and magnetizing inductances of power transformers
with two windings using the properties of a bond graph. The
equivalence between electrical and magnetic variables is given.
The modelling and analysis using this methodology to three phase
power transformers can be extended.
Abstract: The rapid development of manufacturing and information systems has caused significant changes in manufacturing environments in recent decades. Mass production has given way to flexible manufacturing systems, in which an important characteristic is customized or "on demand" production. In this scenario, the seamless and without gaps information flow becomes a key factor for success of enterprises. In this paper we present a framework to support the mapping of features into machining workingsteps compliant with the ISO 14649 standard (known as STEP-NC). The system determines how the features can be made with the available manufacturing resources. Examples of the mapping method are presented for features such as a pocket with a general surface.
Abstract: The tracing methods determine the contribution the
power system sources have in their supplying. The methods can be used
to assess the transmission prices, but also to recover the transmission
fixed cost. In this paper is presented the influence of the modification of
commons structure has on the specific price of transfer. The operator
must make use of a few basic principles about allocation. Most
tracing methods are based on the proportional sharing principle. In this
paper Kirschen method is used. In order to illustrate this method, the 25-
bus test system is used, elaborated within the Electrical Power
Engineering Department, from Timisoara, Romania.
Abstract: The paper presents an analytical solution for dispersion
of a solute in the peristaltic motion of a couple stress fluid
through a porous medium with slip condition in the presence of both
homogeneous and heterogeneous chemical reactions. The average
effective dispersion coefficient has been found using Taylor-s limiting
condition and long wavelength approximation. The effects of various
relevant parameters on the average coefficient of dispersion have been
studied. The average effective dispersion coefficient tends to increase
with permeability parameter but tends to decrease with homogeneous
chemical reaction rate parameter, couple stress parameter, slip parameter
and heterogeneous reaction rate parameter.
Abstract: Ferroresonance is an electrical phenomenon in
nonlinear character, which frequently occurs in power system due to
transmission line faults and single or more-phase switching on the
lines as well as usage of the saturable transformers. In this study, the
ferroresonance phenomena are investigated under the modeling of the
West Anatolian Electric Power Network of 380 kV in Turkey. The
ferroresonance event is observed as a result of removing the loads at
the end of the lines. In this sense, two different cases are considered.
At first, the switching is applied at 2nd second and the ferroresonance
affects are observed between 2nd and 4th seconds in the voltage
variations of the phase-R. Hence the ferroresonance and nonferroresonance
parts of the overall data are compared with each
others using the Fourier transform techniques to show the
ferroresonance affects.
Abstract: In this era of competitiveness, there is a growing need for supply chains also to become competitive enough to handle pressures like varying customer’s expectations, low cost high quality products to be delivered at the minimum time and the most important is throat cutting competition at world wide scale. In the recent years, supply chain competitiveness has been, therefore, accepted as one of the most important philosophies in the supply chain literature. Various researchers and practitioners have tried to identify and implement strategies in supply chains which can bring competitiveness in the supply chains i.e. supply chain competitiveness. The purpose of this paper is to suggest select strategies for supply chain competitiveness in the Indian manufacturing sector using an integrated approach of literature review and exploratory interviews with eminent professionals from the supply chain area in various industries, academia and research. The aim of the paper is to highlight the important area of competitiveness in the supply chain and to suggest recommendations to the industry and managers of manufacturing sector.
Abstract: A study of the obtainable watermark data rate for information hiding algorithms is presented in this paper. As the perceptual entropy for wideband monophonic audio signals is in the range of four to five bits per sample, a significant amount of additional information can be inserted into signal without causing any perceptual distortion. Experimental results showed that transform domain watermark embedding outperforms considerably watermark embedding in time domain and that signal decompositions with a high gain of transform coding, like the wavelet transform, are the most suitable for high data rate information hiding. Keywords?Digital watermarking, information hiding, audio watermarking, watermark data rate.
Abstract: In this paper, we have proposed a novel FinFET with
extended body under the poly gate, which is called EB-FinFET, and
its characteristic is demonstrated by using three-dimensional (3-D)
numerical simulation. We have analyzed and compared it with
conventional FinFET. The extended body height dependence on the
drain induced barrier lowering (DIBL) and subthreshold swing (S.S)
have been also investigated. According to the 3-D numerical
simulation, the proposed structure has a firm structure, an acceptable
short channel effect (SCE), a reduced series resistance, an increased
on state drain current (I
on) and a large normalized I
DS. Furthermore,
the structure can also improve corner effect and reduce self-heating
effect due to the extended body. Our results show that the EBFinFET
is excellent for nanoscale device.
Abstract: Linear stochastic estimation and quadratic stochastic
estimation techniques were applied to estimate the entire velocity
flow-field of an open cavity with a length to depth ratio of 2. The
estimations were done through the use of instantaneous velocity
magnitude as estimators. These measurements were obtained by
Particle Image Velocimetry. The predicted flow was compared
against the original flow-field in terms of the Reynolds stresses and
turbulent kinetic energy. Quadratic stochastic estimation proved to be
more superior than linear stochastic estimation in resolving the shear
layer flow. When the velocity fluctuations were scaled up in the
quadratic estimate, both the time-averaged quantities and the
instantaneous cavity flow can be predicted to a rather accurate extent.
Abstract: I/O workload is a critical and important factor to
analyze I/O pattern and to maximize file system performance.
However to measure I/O workload on running distributed parallel file
system is non-trivial due to collection overhead and large volume of
data. In this paper, we measured and analyzed file system activities on
two large-scale cluster systems which had TFlops level high
performance computation resources. By comparing file system
activities of 2009 with those of 2006, we analyzed the change of I/O
workloads by the development of system performance and high-speed
network technology.
Abstract: Two commercial proteases from Bacillus
licheniformis (Alcalase 2.4 L FG and Alcalase 2.5 L, Type DX) were
screened for the production of Z-Ala-Phe-NH2 in batch reaction.
Alcalase 2.4 L FG was the most efficient enzyme for the C-terminal
amidation of Z-Ala-Phe-OMe using ammonium carbamate as
ammonium source. Immobilization of protease has been achieved by
the sol-gel method, using dimethyldimethoxysilane (DMDMOS) and
tetramethoxysilane (TMOS) as precursors (unpublished results). In
batch production, about 95% of Z-Ala-Phe-NH2 was obtained at
30°C after 24 hours of incubation. Reproducibility of different
batches of commercial Alcalase 2.4 L FG preparations was also
investigated by evaluating the amidation activity and the entrapment
yields in the case of immobilization. A packed-bed reactor (0.68 cm
ID, 15.0 cm long) was operated successfully for the continuous
synthesis of peptide amides. The immobilized enzyme retained the
initial activity over 10 cycles of repeated use in continuous reactor at
ambient temperature. At 0.75 mL/min flow rate of the substrate
mixture, the total conversion of Z-Ala-Phe-OMe was achieved after 5
hours of substrate recycling. The product contained about 90%
peptide amide and 10% hydrolysis byproduct.
Abstract: The current study begins with an awareness that
today-s media environment is characterized by technological
development and a new way of reading caused by the introduction of
the Internet. The researcher conducted a meta analysis framed within
Technological Determinism to investigate the process of hypertext
reading, its differences from linear reading and the effects such
differences can have on people-s ways of mentally structuring their
world. The relationship between literacy and the comprehension
achieved by reading hypertexts is also investigated. The results show
hypertexts are not always user friendly. People experience hyperlinks
as interruptions that distract their attention generating comprehension
and disorientation. On one hand hypertextual jumping reading
generates interruptions that finally make people lose their
concentration. On the other hand hypertexts fascinate people who
would rather read a document in such a format even though the
outcome is often frustrating and affects their ability to elaborate and
retain information.
Abstract: The plastic forming process of sheet plate takes an
important place in forming metals. The traditional techniques of tool
design for sheet forming operations used in industry are experimental
and expensive methods. Prediction of the forming results,
determination of the punching force, blank holder forces and the
thickness distribution of the sheet metal will decrease the production
cost and time of the material to be formed. In this paper, multi-stage
deep drawing simulation of an Industrial Part has been presented
with finite element method. The entire production steps with
additional operations such as intermediate annealing and springback
has been simulated by ABAQUS software under axisymmetric
conditions. The simulation results such as sheet thickness
distribution, Punch force and residual stresses have been extracted in
any stages and sheet thickness distribution was compared with
experimental results. It was found through comparison of results, the
FE model have proven to be in close agreement with those of
experiment.
Abstract: Business scenario is an important technique that may be used at various stages of the enterprise architecture to derive its characteristics based on the high-level requirements of the business. In terms of wireless deployments, they are used to help identify and understand business needs involving wireless services, and thereby to derive the business requirements that the architecture development has to address by taking into account of various wireless challenges. This study assesses the deployment of Wireless Local Area Network (WLAN) and Broadband Wireless Access (BWA) solutions for several business scenarios in Asia Pacific region. This paper focuses on the overview of the business and technology environments, whereby examples of existing (or suggested) wireless solutions (to be) adopted in Asia Pacific region will be discussed. Interactions of several players, enabling technologies, and key processes in the wireless environments are studied. The analysis and discussions associated to this study are divided into two divisions: healthcare and education, where the merits of wireless solutions in improving living quality are highlighted.
Abstract: In this paper, the optimum weight and cost of a laminated composite plate is seeked, while it undergoes the heaviest load prior to a complete failure. Various failure criteria are defined for such structures in the literature. In this work, the Tsai-Hill theory is used as the failure criterion. The theory of analysis was based on the Classical Lamination Theory (CLT). A newly type of Genetic Algorithm (GA) as an optimization technique with a direct use of real variables was employed. Yet, since the optimization via GAs is a long process, and the major time is consumed through the analysis, Radial Basis Function Neural Networks (RBFNN) was employed in predicting the output from the analysis. Thus, the process of optimization will be carried out through a hybrid neuro-GA environment, and the procedure will be carried out until a predicted optimum solution is achieved.
Abstract: In a competitive production environment, critical
decision making are based on data resulted by random sampling of
product units. Efficiency of these decisions depends on data quality
and also their reliability scale. This point leads to the necessity of a
reliable measurement system. Therefore, the conjecture process and
analysing the errors contributes to a measurement system known as
Measurement System Analysis (MSA). The aim of this research is on
determining the necessity and assurance of extensive development in
analysing measurement systems, particularly with the use of
Repeatability and Reproducibility Gages (GR&R) to improve
physical measurements. Nowadays in productive industries,
repeatability and reproducibility gages released so well but they are
not applicable as well as other measurement system analysis
methods. To get familiar with this method and gain a feedback in
improving measurement systems, this survey would be on
“ANOVA" method as the most widespread way of calculating
Repeatability and Reproducibility (R&R).
Abstract: The acidity of different raw Jordanian clays
containing zeolite, bentonite, red and white kaolinite and diatomite
was characterized by means of temperature programmed desorption
(TPD) of ammonia, conversion of 2-methyl-3-butyn-2-ol (MBOH),
FTIR and BET-measurements. FTIR spectra proved presence of
silanol and bridged hydroxyls on the clay surface. The number of
acidic sites was calculated from experimental TPD-profiles. We
observed the decrease of surface acidity correlates with the decrease
of Si/Al ratio except for diatomite. On the TPD-plot for zeolite two
maxima were registered due to different strength of surface acidic
sites. Values of MBOH conversion, product yields and selectivity
were calculated for the catalysis on Jordanian clays. We obtained that
all clay samples are able to convert MBOH into a major product
which is 3-methyl-3-buten-1-yne (MBYNE) catalyzed by acid
surface sites with the selectivity close to 70%. There was found a
correlation between MBOH conversion and acidity of clays
determined by TPD-NH3, i.e. the higher the acidity the higher the
conversion of MBOH. However, diatomite provided the lowest
conversion of MBOH as result of poor polarization of silanol groups.
Comparison of surface areas and conversions revealed the highest
density of active sites for red kaolinite and the lowest for zeolite and
diatomite.