Abstract: When concrete is exposed to high temperatures, some changes may occur in its physical and mechanical properties. Especially, high strength concrete (HSC), may exhibit damages such as cracks and spallings. To overcome this problem, incorporating polymer fibers such as polypropylene (PP) in concrete is a well-known method. In high temperatures, PP decomposes and releases harmful gases such as CO and CO2. This study researches the use of raw rice husk (RRH) as a sustainable material, instead of PP fibers considering its several favorable properties, and its usability in HSC. RRH and PP fibers were incorporated in concrete at 0.5-3% and 0.2-0.5% by weight of cement, respectively. Concrete specimens were exposed to 20 (control), 300, 600 and 900°C. Under these temperatures, residual compressive and splitting tensile strength was determined. During the high temperature effect, the amount of released harmful gases was measured by a gas detector.
Abstract: Ultra-light overhead conveyor systems are rope-based conveying systems with individually driven vehicles. The vehicles can move automatically on the rope and this can be realized by energy and signals. The ultra-light overhead conveyor systems always must be integrated with a logistical process by finding a best way for a cheaper material flow in order to guarantee precise and fast workflows. This paper analyzes the process of an ultra-light overhead conveyor system using necessary assumptions. The analysis consists of three scenarios. These scenarios are based on raising the vehicle speeds with equal increments at each case. The correlation between the vehicle speed and system throughput is investigated. A discrete-event simulation model of an ultra-light overhead conveyor system is constructed using DOSIMIS-3 software to implement three scenarios. According to simulation results; the optimal scenario, hence the optimal vehicle speed, is found out among three scenarios. This simulation model demonstrates the effect of increased speed on the system throughput.
Abstract: Linear systems are widely used in many fields of science and engineering. In many applications, at least some of the parameters of the system are represented by fuzzy rather than crisp numbers. Therefore it is important to perform numerical algorithms or procedures that would treat general fuzzy linear systems and solve them using iterative methods. This paper aims are to solve fuzzy linear systems using four types of Jacobi based iterative methods. Four iterative methods based on Jacobi are used for solving a general n × n fuzzy system of linear equations of the form Ax = b , where A is a crisp matrix and b an arbitrary fuzzy vector. The Jacobi, Jacobi Over-Relaxation, Refinement of Jacobi and Refinement of Jacobi Over-Relaxation methods was tested to a five by five fuzzy linear system. It is found that all the tested methods were iterated differently. Due to the effect of extrapolation parameters and the refinement, the Refinement of Jacobi Over-Relaxation method was outperformed the other three methods.
Abstract: Background and objectives: Most of the agricultural products are processed by blanching. Blanching can increase antioxidant activity in white saffron products. The objective of this research were to determine antioxidant activity, to identify, and to measure changes in phenolic substances of fresh and blanched white saffron rhizomes (Curcuma mangga Val.). Methods: White saffron rhizomes were peeled, washed and blanched in boiling water containing 0% or 0.05% citric acid solution for 5 and 10 minutes. Samples were extracted using methanol, rotaevaporated, and freezedried. Dried extract was determined antioxidant activity by DPPH method, identified and quantified for the phenolic substances by High Performance Liquid Chromatography (HPLC) equipped with coloumn C18 and Photodiode-array detector (PAD). Result: This research showed that the quantity of the 6 phenolic substances identified in blanched white saffron in citric acid solution increased significantly compared to that of the non-blanched. Blanching white saffron in 0.05% citric acid media for 5 minutes increased its antioxidant activity, and total phenolic content. Conclusions: The identified phenolic substances of white saffron were Gallic Acid (GA), Catechin (C), Epicatechin (EC), Epigallocatechin (EGC), Epigallocatechingallat (EGCG) and Gallocatechingallat (GCG). The blanched white saffron contained C and EGCG significantly higher than that of fresh rhizomes.
Abstract: The brand storytelling themes and emotional appeals of three major global brands were analysed by means of visual rhetoric in a digital environment focusing on the ethos communication technique. A well-known framework of five basic brand personality dimensions was used to delineate the analysis. Brand storytelling as a branding technique is becoming increasingly popular, especially since all brands can tell a story to connect and engage with consumers on an emotional level. Social media have changed the way in which brand stories are shared with online consumers, while social video networking sites in particular create an opportunity to share brand stories with a much greater target audience through electronic word of mouth (eWOM). The findings not only confirm three dimensions in the traditional brand personality framework, but can also serve as a heuristic tool for other researchers analyzing brand storytelling in a social video sharing network environment.
Abstract: Gait disturbance, particularly freezing of gait (FOG), is a phenomenon that is common in Parkinson’s patients and significantly contributes to a loss of function and independence. Walking performance and number of freezing episodes have been known to respond favorably to sensory cues of different modalities. However, a topic that has so far barely been touched is how to resolve freezing episodes via sensory cues once they have appeared. In this study, we analyze the effect of five different sensory cues on the duration of freezing episodes: (1) vibratory alert, (2) auditory alert, (3) vibratory rhythm, (4) auditory rhythm, (5) visual cue in form of parallel lines projected to the floor. The motivation for this study is to investigate the possibility of the design of a gait assistive device for Parkinson’s patients. Test subjects were 7 Parkinson’s patients regularly suffering from FOG. The patients had to repeatedly walk a pre-defined course and cues were triggered always 2 s after freezing onset. The effect was analyzed via experimental measurements and patient interviews. The measurements showed that all 5 sensory cues led to a decrease of the average duration of freezing: baseline (7.9s), vibratory alert (7.1s), auditory alert (6.7s), auditory rhythm (6.4s), vibratory rhythm (6.3s), and visual cue (5.3s). Nevertheless, interestingly, patients subjectively evaluated the audio alert and vibratory signals to have a significantly better effect for reducing their freezing duration than the visual cue.
Abstract: In the present study, the problem of geometrically nonlinear free vibrations of functionally graded circular plates (FGCP) resting on Pasternak elastic foundation with immovable ends was studied. The material properties of the functionally graded composites examined were assumed to be graded in the thickness direction and estimated through the rule of mixture. The theoretical model is based on the classical Plate theory and the Von Kármán geometrical nonlinearity assumptions. Hamilton’s principle is applied and a multimode approach is derived to calculate the fundamental nonlinear frequency parameters, which are found to be in a good agreement with the published results dealing with the problem of functionally graded plates. On the other hand, the influence of the foundation parameters on the nonlinear frequency to the linear frequency ratio of the FGCP has been studied. The effect of the linear and shearing foundations is to decrease the frequency ratio, where it increases with the effect of the nonlinear foundation stiffness.
Abstract: Carbon dioxide has been well associated with greenhouse effect, and due to its corrosive nature it is an undesirable compound. A variety of physical-chemical processes are available for the removal of carbon dioxide. Previous attempts in this field have established alkanolamine group has the capability to remove carbon dioxide. So, this study combined the polymeric membrane and alkanolamine solutions to fabricate the amine polymeric membrane (APM) to remove carbon dioxide (CO2). This study entails the effect of three types of amines, monoethanolamine (MEA), diethanolamine (DEA), and methyldiethanolamine (MDEA). The effect of each alkanolamine group on the morphology and performance of polyether sulfone (PES) polymeric membranes was studied. Flat sheet membranes were fabricated by solvent evaporation method by adding polymer and different alkanolamine solutions in the N-Methyl-2-pyrrolidone (NMP) solvent. The final membranes were characterized by using Field Emission Electron Microscope (FESEM), Fourier Transform Infrared (FTIR), and Thermo-Gravimetric Analysis (TGA). The membrane separation performance was studied. The PES-DEA and PES-MDEA membrane has good ability to remove carbon dioxide.
Abstract: Fly ash is a waste material of coal firing thermal
plants that is released from thermal power plants. It was defined as
very fine particles that are drifted upward which are taken up by the
flue gases. The emerging amount of fly ash in the world is
approximately 600 million tons per year. In our country, it is
expected that will be occurred 50 million tons of waste ash per year
until 2020. The fly ashes can be evaluated by using as adsorbent
material. The purpose of this study is to investigate the possibility of
use of various fly ashes (Tuncbilek, Catalagzi, Orhaneli) like lowcost
adsorbents for heavy metal adsorption. First of all, fly ashes
were characterized. For this purpose; analyses such as XRD, XRF,
SEM and FT-IR were performed.
Abstract: The problem of optimal planning of multiple sources
of distributed generation (DG) in distribution networks is treated in
this paper using an improved Ant Colony Optimization algorithm
(ACO). This objective of this problem is to determine the DG
optimal size and location that in order to minimize the network real
power losses. Considering the multiple sources of DG, both size and
location are simultaneously optimized in a single run of the proposed
ACO algorithm. The various practical constraints of the problem are
taken into consideration by the problem formulation and the
algorithm implementation. A radial power flow algorithm for
distribution networks is adopted and applied to satisfy these
constraints. To validate the proposed technique and demonstrate its
effectiveness, the well-know 69-bus feeder standard test system is
employed.cm.
Abstract: Different approaches for heating\cooling of stirred tanks, coils and jackets, are investigated using computational fluid dynamics (CFD).A time-dependant sliding mesh approach is applied to simulate the flow in both conditions. The investigations are carried out under the turbulent flow conditions for a Rushton impeller and heating elements are considered isothermal. The flow behavior and temperature distribution are studied for each case and heat transfer coefficient is calculated. Results show different velocity profiles for each case. Unsteady temperature distribution is not similar for different cases .In the case of the coiled stirred vessel more uniform temperature and higher heat transfer coefficient is resulted.
Abstract: This paper describes fast and efficient method for page segmentation of document containing nonrectangular block. The segmentation is based on edge following algorithm using small window of 16 by 32 pixels. This segmentation is very fast since only border pixels of paragraph are used without scanning the whole page. Still, the segmentation may contain error if the space between them is smaller than the window used in edge following. Consequently, this paper reduce this error by first identify the missed segmentation point using direction information in edge following then, using X-Y cut at the missed segmentation point to separate the connected columns. The advantage of the proposed method is the fast identification of missed segmentation point. This methodology is faster with fewer overheads than other algorithms that need to access much more pixel of a document.
Abstract: The impacts of near-campus student housing, or offcampus
students accommodation cannot be ignored by the
universities and as well as the community officials. Numerous
scholarly studies, have highlighted the substantial economic impacts
either; direct, indirect or induced, and cumulatively the roles of the
universities have significantly contributed to the local economies.
The issue of the impacts of off-campus student rental housing on
neighbourhoods is one that has been of long-standing but increasing
concern in Malaysia. Statistically, in Malaysia, there was
approximately a total of 1.2 - 1.5 million students in 2009. By the
year 2015, it is expected that 50 per cent of 18 to 30 year olds active
population should gain access to university education, amounting to
120,000 yearly. The objectives of the research are to assess the
impacts off-campus students on the local neighbourhood and
specifically to obtain information on the living and learning
conditions of off-campus students of Universiti Teknologi MARA
Shah Alam, Malaysia. It is also to isolate those factors that may
impede the successful learning so that priority can be given to them
in subsequent policy implementations and actions by government and
the higher education institutions.
Abstract: Signature amortization schemes have been introduced
for authenticating multicast streams, in which, a single signature is
amortized over several packets. The hash value of each packet is
computed, some hash values are appended to other packets, forming
what is known as hash chain. These schemes divide the stream into
blocks, each block is a number of packets, the signature packet in
these schemes is either the first or the last packet of the block.
Amortization schemes are efficient solutions in terms of computation
and communication overhead, specially in real-time environment.
The main effictive factor of amortization schemes is it-s hash chain
construction. Some studies show that signing the first packet of each
block reduces the receiver-s delay and prevents DoS attacks, other
studies show that signing the last packet reduces the sender-s delay.
To our knowledge, there is no studies that show which is better, to
sign the first or the last packet in terms of authentication probability
and resistance to packet loss.
In th is paper we will introduce another scheme for authenticating
multicast streams that is robust against packet loss, reduces the
overhead, and prevents the DoS attacks experienced by the receiver
in the same time. Our scheme-The Multiple Connected Chain signing
the First packet (MCF) is to append the hash values of specific
packets to other packets,then append some hashes to the signature
packet which is sent as the first packet in the block. This scheme
is aspecially efficient in terms of receiver-s delay. We discuss and
evaluate the performance of our proposed scheme against those that
sign the last packet of the block.
Abstract: Heterogeneous repolarization causes dispersion of the T-wave and has been linked to arrhythmogenesis. Such heterogeneities appear due to differential expression of ionic currents in different regions of the heart, both in healthy and diseased animals and humans. Mice are important animals for the study of heart diseases because of the ability to create transgenic animals. We used our previously reported model of mouse ventricular myocytes to develop 2D mouse ventricular tissue model consisting of 14,000 cells (apical or septal ventricular myocytes) and to study the stability of action potential propagation and Ca2+ dynamics. The 2D tissue model was implemented as a FORTRAN program code for highperformance multiprocessor computers that runs on 36 processors. Our tissue model is able to simulate heterogeneities not only in action potential repolarization, but also heterogeneities in intracellular Ca2+ transients. The multicellular model reproduced experimentally observed velocities of action potential propagation and demonstrated the importance of incorporation of realistic Ca2+ dynamics for action potential propagation. The simulations show that relatively sharp gradients of repolarization are predicted to exist in 2D mouse tissue models, and they are primarily determined by the cellular properties of ventricular myocytes. Abrupt local gradients of channel expression can cause alternans at longer pacing basic cycle lengths than gradual changes, and development of alternans depends on the site of stimulation.
Abstract: The purpose of this study is to analyze the visual
preference of patterns in pedestrian roads. In this study, animation was
applied for the estimation of dynamic streetscape. Six patterns of
pedestrian were selected in order to analyze the visual preference. The
shapes are straight, s-curve, and zigzag. The ratio of building's height
and road's width are 2:1 and 1:1. Twelve adjective pairs used in the
field investigation were selected from adjectives which are used
usually in the estimation of streetscape. They are interesting-boring,
simple-complex, calm-noisy, open-enclosed, active-inactive,
lightly-depressing, regular-irregular, unique-usual, rhythmic-not
rhythmic, united-not united, stable-unstable, tidy-untidy.
Dynamic streetscape must be considered important in pedestrian
shopping mall and park because it will be an attraction. So, s-curve
pedestrian road, which is the most beautiful as a result of this study,
should be designed in this area. Also, the ratio of building's height and
road's width along pedestrian road should be reduced.
Abstract: Brushless DC motor with high torque density and slim
topology for easy loading for robot system is proposed and
manufactured. Electromagnetic design is executed by equivalent
magnetic circuit model and numerical analysis. Manufactured motor is
tested and verified characteristics comparing with conventional BLDC
motor.
Abstract: In this paper we introduce an effective ECG compression algorithm based on two dimensional multiwavelet transform. Multiwavelets offer simultaneous orthogonality, symmetry and short support, which is not possible with scalar two-channel wavelet systems. These features are known to be important in signal processing. Thus multiwavelet offers the possibility of superior performance for image processing applications. The SPIHT algorithm has achieved notable success in still image coding. We suggested applying SPIHT algorithm to 2-D multiwavelet transform of2-D arranged ECG signals. Experiments on selected records of ECG from MIT-BIH arrhythmia database revealed that the proposed algorithm is significantly more efficient in comparison with previously proposed ECG compression schemes.
Abstract: Defect prevention is the most vital but habitually
neglected facet of software quality assurance in any project. If
functional at all stages of software development, it can condense the
time, overheads and wherewithal entailed to engineer a high quality
product. The key challenge of an IT industry is to engineer a
software product with minimum post deployment defects.
This effort is an analysis based on data obtained for five selected
projects from leading software companies of varying software
production competence. The main aim of this paper is to provide
information on various methods and practices supporting defect
detection and prevention leading to thriving software generation. The
defect prevention technique unearths 99% of defects. Inspection is
found to be an essential technique in generating ideal software
generation in factories through enhanced methodologies of abetted
and unaided inspection schedules. On an average 13 % to 15% of
inspection and 25% - 30% of testing out of whole project effort time
is required for 99% - 99.75% of defect elimination.
A comparison of the end results for the five selected projects
between the companies is also brought about throwing light on the
possibility of a particular company to position itself with an
appropriate complementary ratio of inspection testing.
Abstract: The aim of this research was to calculate the
mechanical properties of Pd3Rh and PdRh3 ordered alloys. The
molecular dynamics (MD) simulation technique was used to obtain
temperature dependence of the energy, the Yong modulus, the shear
modulus, the bulk modulus, Poisson-s ratio and the elastic stiffness
constants at the isobaric-isothermal (NPT) ensemble in the range of
100-325 K. The interatomic potential energy and force on atoms were
calculated by Quantum Sutton-Chen (Q-SC) many body potential.
Our MD simulation results show the effect of temperature on the
cohesive energy and mechanical properties of Pd3Rh as well as
PdRh3 alloys. Our computed results show good agreement with the
experimental results where they have been available.