Abstract: An approach to develop the FPGA of a flexible key
RSA encryption engine that can be used as a standard device in the
secured communication system is presented. The VHDL modeling of
this RSA encryption engine has the unique characteristics of
supporting multiple key sizes, thus can easily be fit into the systems
that require different levels of security. A simple nested loop addition
and subtraction have been used in order to implement the RSA
operation. This has made the processing time faster and used
comparatively smaller amount of space in the FPGA. The hardware
design is targeted on Altera STRATIX II device and determined that
the flexible key RSA encryption engine can be best suited in the
device named EP2S30F484C3. The RSA encryption implementation
has made use of 13,779 units of logic elements and achieved a clock
frequency of 17.77MHz. It has been verified that this RSA
encryption engine can perform 32-bit, 256-bit and 1024-bit
encryption operation in less than 41.585us, 531.515us and 790.61us
respectively.
Abstract: Trace element speciation of an integrated soil
amendment matrix was studied with a modified BCR sequential
extraction procedure. The analysis included pseudo-total
concentration determinations according to USEPA 3051A and
relevant physicochemical properties by standardized methods. Based
on the results, the soil amendment matrix possessed neutralization
capacity comparable to commercial fertilizers. Additionally, the
pseudo-total concentrations of all trace elements included in the
Finnish regulation for agricultural fertilizers were lower than the
respective statutory limit values. According to chemical speciation,
the lability of trace elements increased in the following order: Hg <
Cr < Co < Cu < As < Zn < Ni < Pb < Cd < V < Mo < Ba. The
validity of the BCR approach as a tool for chemical speciation was
confirmed by the additional acid digestion phase. Recovery of trace
elements during the procedure assured the validity of the approach
and indicated good quality of the analytical work.
Abstract: Due to a high unemployment rate among local people
and a high reliance on expatriate workers, the governments in the
Gulf Co-operation Council (GCC) countries have been implementing
programmes of localisation (replacing foreign workers with GCC
nationals). These programmes have been successful in the public
sector but much less so in the private sector. However, there are now
insufficient jobs for locals in the public sector and the onus to provide
employment has fallen on the private sector. This paper is concerned
with a study, which is a work in progress (certain elements are
complete but not the whole study), investigating the effective
implementation of localisation policies in four- and five-star hotels in
the Kingdom of Saudi Arabia (KSA) and the United Arab Emirates
(UAE). The purpose of the paper is to identify the research gap, and
to present the need for the research. Further, it will explain how this
research was conducted.
Studies of localisation in the GCC countries are under-represented
in scholarly literature. Currently, the hotel sectors in KSA and UAE
play an important part in the countries’ economies. However, the
total proportion of Saudis working in the hotel sector in KSA is
slightly under 8%, and in the UAE, the hotel sector remains highly
reliant on expatriates. There is therefore a need for research on
strategies to enhance the implementation of the localisation policies
in general and in the hotel sector in particular.
Further, despite the importance of the hotel sector to their
economies, there remains a dearth of research into the
implementation of localisation policies in this sector. Indeed, as far as
the researchers are aware, there is no study examining localisation in
the hotel sector in KSA, and few in the UAE. This represents a
considerable research gap.
Regarding how the research was carried out, a multiple case study
strategy was used. The four- and five-star hotel sector in KSA is one
of the cases, while the four- and five-star hotel sector in the UAE is
the other case. Four- and five-star hotels in KSA and the UAE were
chosen as these countries have the longest established localisation
policies of all the GCC states and there are more hotels of these
classifications in these countries than in any of the other Gulf
countries. A literature review was carried out to underpin the
research. The empirical data were gathered in three phases. In order
to gain a pre-understanding of the issues pertaining to the research
context, Phase I involved eight unstructured interviews with officials
from the Saudi Commission for Tourism and Antiquities (three
interviewees); the Saudi Human Resources Development Fund (one);
the Abu Dhabi Tourism and Culture Authority (three); and the Abu
Dhabi Development Fund (one).
In Phase II, a questionnaire was administered to 24 managers and
24 employees in four- and five-star hotels in each country to obtain
their beliefs, attitudes, opinions, preferences and practices concerning
localisation.
Unstructured interviews were carried out in Phase III with six
managers in each country in order to allow them to express opinions
that may not have been explored in sufficient depth in the
questionnaire. The interviews in Phases I and III were analysed using
thematic analysis and SPSS will be used to analyse the questionnaire
data.
It is recommended that future research be undertaken on a larger
scale, with a larger sample taken from all over KSA and the UAE
rather than from only four cities (i.e., Riyadh and Jeddah in KSA and
Abu Dhabi and Sharjah in the UAE), as was the case in this research.
Abstract: A new topology of unified power quality conditioner
(UPQC) is proposed for different power quality (PQ) improvement in
a three-phase four-wire (3P-4W) distribution system. For neutral
current mitigation, a star-hexagon transformer is connected in shunt
near the load along with three-leg voltage source inverters (VSIs)
based UPQC. For the mitigation of source neutral current, the uses of
passive elements are advantageous over the active compensation due
to ruggedness and less complexity of control. In addition to this, by
connecting a star-hexagon transformer for neutral current mitigation
the over all rating of the UPQC is reduced. The performance of the
proposed topology of 3P-4W UPQC is evaluated for power-factor
correction, load balancing, neutral current mitigation and mitigation
of voltage and currents harmonics. A simple control algorithm based
on Unit Vector Template (UVT) technique is used as a control
strategy of UPQC for mitigation of different PQ problems. In this
control scheme, the current/voltage control is applied over the
fundamental supply currents/voltages instead of fast changing APFs
currents/voltages, thereby reducing the computational delay.
Moreover, no extra control is required for neutral source current
compensation; hence the numbers of current sensors are reduced. The
performance of the proposed topology of UPQC is analyzed through
simulations results using MATLAB software with its Simulink and
Power System Block set toolboxes.
Abstract: It has often been said that the strength of any country
resides in the strength of its industrial sector, and Progress in
industrial society has been accomplished by the creation of new
technologies. Developments have been facilitated by the increasing
availability of advanced manufacturing technology (AMT), in
addition the implementation of advanced manufacturing technology
(AMT) requires careful planning at all levels of the organization to
ensure that the implementation will achieve the intended goals.
Justification and implementation of advanced manufacturing
technology (AMT) involves decisions that are crucial for the
practitioners regarding the survival of business in the present days of
uncertain manufacturing world. This paper assists the industrial
managers to consider all the important criteria for success AMT
implementation, when purchasing new technology. Concurrently,
this paper classifies the tangible benefits of a technology that are
evaluated by addressing both cost and time dimensions, and the
intangible benefits are evaluated by addressing technological,
strategic, social and human issues to identify and create awareness of
the essential elements in the AMT implementation process and
identify the necessary actions before implementing AMT.
Abstract: Today, building automation is advancing from simple
monitoring and control tasks of lightning and heating towards more
and more complex applications that require a dynamic perception
and interpretation of different scenes occurring in a building. Current
approaches cannot handle these newly upcoming demands. In this
article, a bionically inspired approach for multimodal, dynamic scene
perception and interpretation is presented, which is based on neuroscientific
and neuro-psychological research findings about the perceptual
system of the human brain. This approach bases on data from diverse
sensory modalities being processed in a so-called neuro-symbolic
network. With its parallel structure and with its basic elements being
information processing and storing units at the same time, a very
efficient method for scene perception is provided overcoming the
problems and bottlenecks of classical dynamic scene interpretation
systems.
Abstract: Safety, river environment, and sediment utilization are the elements of the target of sediment management. As a change in an element by sediment management, may affect the other two elements, and the priority among three elements depends on stakeholders. It is necessary to develop a method to evaluate the effect of sediment management on each element and an integrated evaluation method for socio-economic effect. In this study, taking Mount Merapi basin as an investigation field, the method for an active volcanic basin was developed. An integrated evaluation method for sediment management was discussed from a socio-economic point on safety, environment, and sediment utilization and a case study of sediment management was evaluated by means of this method. To evaluate the effect of sediment management, some parameters on safety, utilization, and environment have been introduced. From a utilization point of view, job opportunity, additional income of local people, and tax income to local government were used to evaluate the effectiveness of sediment management. The risk degree of river infrastructure was used to describe the effect of sediment management on a safety aspect. To evaluate the effects of sediment management on environment, the mean diameter of grain size distribution of riverbed surface was used. On the coordinate system designating these elements, the direction of change in basin condition by sediment management can be predicted, so that the most preferable sediment management can be decided. The results indicate that the cases of sediment management tend to give the negative impacts on sediment utilization. However, these sediment managements will give positive impacts on safety and environment condition. Evaluation result from a social-economic point of view shows that the case study of sediment management reduces job opportunity and additional income for inhabitants as well as tax income for government. Therefore, it is necessary to make another policy for creating job opportunity for inhabitants to support these sediment managements.
Abstract: A proposed small-signal model parameters for a pseudomorphic high electron mobility transistor (PHEMT) is presented. Both extrinsic and intrinsic circuit elements of a smallsignal model are determined using genetic algorithm (GA) as a stochastic global search and optimization tool. The parameters extraction of the small-signal model is performed on 200-μm gate width AlGaAs/InGaAs PHEMT. The equivalent circuit elements for a proposed 18 elements model are determined directly from the measured S- parameters. The GA is used to extract the parameters of the proposed small-signal model from 0.5 up to 18 GHz.
Abstract: This paper reviews the greenhouse gas emissions of prefabrication elements for residential development in Hong Kong. Prefabrication becomes a common practice in residential development in Hong Kong and is considered as a green approach. In Hong Kong, prefabrication took place at factories in Pearl River Delta. Although prefabrication reduces construction wastage, it might generate more greenhouse gas emission from transportation and manufacturing processes. This study attempts to measure the “cradle to site" greenhouse gas emission from prefabrication elements for a public housing development in Kai Tak area. The findings could help further reduction of greenhouse gas emissions through process improvement.
Abstract: The springs located in urban areas are the outpouring
of surface water, which can serve as water supply, effluent receptors
and important local macro-drainage elements. With unplanned
occupation, non-compliance with environmental legislation and the
importance of these water bodies, it is vital to analyze the springs
within urban areas, considering the Brazilian forest code. This paper
submits an analysis and discussion methodology proposal of
environmental compliance functions of urban springs, by means of
G.I.S. - Geographic Information System analysis - and in situ
analysis. The case study included two springs which exhibit a history
of occupation along its length, with different degrees of impact. The
proposed method is effective and easy to apply, representing a
powerful tool for analyzing the environmental conditions of springs
in urban areas.
Abstract: Tea has several types of essential elements. Potassium,
magnesium and phosphorus are some examples of these elements.
Tea is widely used drink in Turkey, also some people puts a lemon
wedge to tea for different taste. In this study potassium, magnesium
and phosphorus contents after the hot water brewing of black and
green tea were determined by Optical Emission Spectroscopy (ICPOES).
Furthermore, how the lemon addition to teas affects the
concentrations of the potassium, magnesium and phosphorus
amount are investigated.
From the results, potassium, magnesium and phosphorus
concentrations are found as 3003.3, 597.1, 1167.2 ppm in black tea
and 3718.0, 3830.5, 376.4 ppm in green tea, respectively. After
lemon addition potassium, magnesium and phosphorus
concentrations are changed to 14930, 830.4, 1113.5 ppm in black tea
and 15460.0, 909.5, 1152.5 ppm in green tea, respectively.
It is seen that lemon addition affects some essential elements in
black and green Turkish teas.
Abstract: Newton-Raphson State Estimation method using bus
admittance matrix remains as an efficient and most popular method to
estimate the state variables. Elements of Jacobian matrix are computed
from standard expressions which lack physical significance. In this
paper, elements of the state estimation Jacobian matrix are obtained
considering the power flow measurements in the network elements.
These elements are processed one-by-one and the Jacobian matrix H is
updated suitably in a simple manner. The constructed Jacobian matrix
H is integrated with Weight Least Square method to estimate the state
variables. The suggested procedure is successfully tested on IEEE
standard systems.
Abstract: This work presents a study on the abrasive water jet
(AWJ) machining. An explicit finite element analysis (FEA) of
single abrasive particle impact on stainless steel 1.4304 (AISI 304) is
conducted. The abrasive water jet machining is modeled by FEA
software ABAQUS/CAE. Shapes of craters in FEM simulation
results were used and compared with the previous experimental and
FEM works by means of crater sphericity. The influence of impact
angle and particle velocity was observed. Adaptive mesh domain is
used to model the impact zone. Results are in good agreement with
those obtained from the experimental and FEM simulation. The
crater-s depth is also obtained for different impact angle and abrasive
particle velocities.
Abstract: It is discussed about modern usage of adopted words
and their vocabularies, Turkism usage fields, phonetic, grammatical
and lexis-semantic assimilation of the typological-morphological
structures of entering to different Hindi languages in comparative
typological aspects in this scientific article. The lexis vocabulary is
rich, the prevalence area is wide and it has researched the entering
process of vocabulary into the great languages of Turkic elements
from the speakers- numbers. The research work has worked on the
base of Hindi vocabulary.
Abstract: Even though so many efforts have been taken to
renovate and renew the architecture of Miyaneh villages in cold and
dry regions of Iran-s northwest, these efforts failed due to lack of
significant study and ignoring the past and sustainable history of
those villages. Considering the overpopulation of Iran-s villages as
well as the importance in preventing their immigration to cities,
recognizing village architecture and its construction technology is of
great significance to attain sustainable residence in villages. As the
only vertical surface in the space, wall possesses its unique special
characteristics, and it is also a very important architectural element
able to provide the immunity and comfort space for the residents.
This article analyzes the characteristics of this vertical element, main
types of adobe and stone walls, locally constructed technologies,
implementation, the elements forming the walls in the frame of
village house typology of Miyaneh, which has the most villages in
East Azerbaijan, based on sustainable architectural construction
materials of walls.
Abstract: The demand for autonomous resource
management for distributed systems has increased in recent
years. Distributed systems require an efficient and powerful
communication mechanism between applications running on
different hosts and networks. The use of mobile agent
technology to distribute and delegate management tasks
promises to overcome the scalability and flexibility limitations
of the currently used centralized management approach. This
work proposes a multiagent system that adopts mobile agents
as a technology for tasks distribution, results collection, and
management of resources in large-scale distributed systems. A
new mobile agent-based approach for collecting results from
distributed system elements is presented. The technique of
artificial intelligence based on intelligent agents giving the
system a proactive behavior. The presented results are based
on a design example of an application operating in a mobile
environment.
Abstract: As a part of evaluation system for R&D program, the
Korean government has applied feasibility analysis since 2008.
Various professionals put forth a great effort in order to catch up the
high degree of freedom of R&D programs, and make contributions to
evolving the feasibility analysis. We analyze diverse R&D programs
from various viewpoints, such as technology, policy, and Economics,
integrate the separate analysis, and finally arrive at a definite result;
whether a program is feasible or unfeasible. This paper describes the
concept and method of the feasibility analysis as a decision making
tool. The analysis unit and content of each criterion, which are key
elements in a comprehensive decision making structure, are examined
Abstract: The genre of fantasy depicts a world of imagine that triggers popular interest from a created view of world, and a fantasy is defined as a story that illustrates a world of imagine where scientific or horror elements are stand in its center. This study is not focused on the narrative of the fantasy, i.e. not on the adventurous story, but is concentrated on the image of the fantasy to work on its relationship with intended themes and differences among cultures due to meanings of materials. As for films, we have selected some films in the 2000's that are internationally recognized as expressing unique images of fantasy containing the theme of love in them. The selected films are 5 pieces including two European films, Amelie from Montmartre (2001) and The Science of Sleep (2005) and three Asian films, Citizen Dog from Thailand (2004), Memories of Matsuko from Japan (2006), and I'm a Cyborg, but That's OK from Korea (2006). These films share some common characteristics to the effect that they give tiny lessons and feelings for life with expressions of fantasy images as if they were fairy tales for adults and that they lead the audience to reflect on their days and revive forgotten dreams of childhood. We analyze the images of fantasy in each of the films on the basis of the elements of Mise-en-Scène (setting and props, costume, hair and make-up, facial expressions and body language, lighting and color, positioning of characters, and objects within a frame).
Abstract: The environmental impact caused by industries is an issue that, in the last 20 years, has become very important in terms of society, economics and politics in Colombia. Particularly, the tannery process is extremely polluting because of uneffective treatments and regulations given to the dumping process and atmospheric emissions. Considering that, this investigation is intended to propose a management model based on the integration of Lean Supply Chain, Green Supply Chain, Cleaner Production and ISO 14001-2004, that prioritizes the strategic components of the organizations. As a result, a management model will be obtained and it will provide a strategic perspective through a systemic approach to the tanning process. This will be achieved through the use of Multicriteria Decision tools, along with Quality Function Deployment and Fuzzy Logic. The strategic approach that embraces the management model using the alignment of Lean Supply Chain, Green Supply Chain, Cleaner Production and ISO 14001-2004, is an integrated perspective that allows a gradual frame of the tactical and operative elements through the correct setting of the information flow, improving the decision making process. In that way, Small Medium Enterprises (SMEs) could improve their productivity, competitiveness and as an added value, the minimization of the environmental impact. This improvement is expected to be controlled through a Dashboard that helps the Organization measure its performance along the implementation of the model in its productive process.
Abstract: This paper presents a novel method for prediction of
the mechanical behavior of proximal femur using the general
framework of the quantitative computed tomography (QCT)-based
finite element Analysis (FEA). A systematic imaging and modeling
procedure was developed for reliable correspondence between the
QCT-based FEA and the in-vitro mechanical testing. A speciallydesigned
holding frame was used to define and maintain a unique
geometrical reference system during the analysis and testing. The
QCT images were directly converted into voxel-based 3D finite
element models for linear and nonlinear analyses. The equivalent
plastic strain and the strain energy density measures were used to
identify the critical elements and predict the failure patterns. The
samples were destructively tested using a specially-designed gripping
fixture (with five degrees of freedom) mounted within a universal
mechanical testing machine. Very good agreements were found
between the experimental and the predicted failure patterns and the
associated load levels.