Abstract: Machining parameters are very important in
determining the surface quality of any material. In the past decade,
some new engineering materials were developed for the
manufacturing industry which created a need to conduct an
investigation on the impact of the said parameters on their surface
roughness. Polyurethane (PU) block is widely used in the automotive
industry to manufacture parts such as checking fixtures that are used
to verify the dimensional accuracy of automotive parts. In this paper,
the design of experiment (DOE) was used to investigate on the effect
of the milling parameters on the PU block. Furthermore, an analysis
of the machined surface chemical composition was done using
scanning electron microscope (SEM). It was found that the surface
roughness of the PU block is severely affected when PU undergoes a
flood machining process instead of a dry condition. In addition the
stepover and the silicon content were found to be the most significant
parameters that influence the surface quality of the PU block.
Abstract: Safety is one of the most important considerations
when buying a new car. While active safety aims at avoiding
accidents, passive safety systems such as airbags and seat belts
protect the occupant in case of an accident. In addition to legal
regulations, organizations like Euro NCAP provide consumers with
an independent assessment of the safety performance of cars and
drive the development of safety systems in automobile industry.
Those ratings are mainly based on injury assessment reference values
derived from physical parameters measured in dummies during a car
crash test.
The components and sub-systems of a safety system are designed
to achieve the required restraint performance. Sled tests and other
types of tests are then carried out by car makers and their suppliers
to confirm the protection level of the safety system. A Knowledge
Discovery in Databases (KDD) process is proposed in order to
minimize the number of tests. The KDD process is based on the
data emerging from sled tests according to Euro NCAP specifications.
About 30 parameters of the passive safety systems from different data
sources (crash data, dummy protocol) are first analysed together with
experts opinions. A procedure is proposed to manage missing data
and validated on real data sets. Finally, a procedure is developed to
estimate a set of rough initial parameters of the passive system before
testing aiming at reducing the number of tests.
Abstract: Bamboo is extensively used in construction industry.
Low durability of bamboo due to fungus infestation and termites
attack under storage puts certain constrains for it usage as modern
structural material. Looking at many chemical formulations for
bamboo treatment leading to severe harmful environment effects,
research on eco-friendly preservatives for bamboo treatment has been
initiated world-over. In the present studies, eco-friendly preservative
for bamboo treatment has been developed. To validate its application
for structural purposes, investigation of effect of treatment on
compressive strength has been investigated. Neemoil (25%)
integrated with copper naphthenate (0.3%) on dilution with kerosene
oil impregnated into bamboo culm at 2 bar pressure, has shown
weight loss of only 3.15% in soil block analysis method. The results
from compressive strength analysis using HEICO Automatic
Compression Testing Machine reveal that preservative treatment has
not altered the structural properties of bamboo culms. Compressive
strength of control (11.72 N/mm2) and above treated samples (11.71
N/mm2) was found to be comparable.
Abstract: Electricity spot prices are highly volatile under
optimal generation capacity scenarios due to factors such as nonstorability
of electricity, peak demand at certain periods, generator
outages, fuel uncertainty for renewable energy generators, huge
investments and time needed for generation capacity expansion etc.
As a result market participants are exposed to price and volume risk,
which has led to the development of risk management practices. This
paper provides an overview of risk management practices by market
participants in electricity markets using financial derivatives.
Abstract: Metal matrix composites (MMCs) attract considerable
attention as a result from its ability in providing a high strength, high
modulus, high toughness, high impact properties, improving wear
resistance and providing good corrosion resistance compared to
unreinforced alloy. Aluminium Silicon (Al/Si) alloy MMC has been
widely used in various industrial sectors such as in transportation,
domestic equipment, aerospace, military, construction, etc.
Aluminium silicon alloy is an MMC that had been reinforced with
aluminium nitrate (AlN) particle and become a new generation
material use in automotive and aerospace sector. The AlN is one of
the advance material that have a bright prospect in future since it has
features such as lightweight, high strength, high hardness and
stiffness quality. However, the high degree of ceramic particle
reinforcement and the irregular nature of the particles along the
matrix material that contribute to its low density is the main problem
which leads to difficulties in machining process. This paper examined
the tool wear when milling AlSi/AlN Metal Matrix Composite using
a TiB2 (Titanium diboride) coated carbide cutting tool. The volume
of the AlN reinforced particle was 10% and milling process was
carried out under dry cutting condition. The TiB2 coated carbide
insert parameters used were at the cutting speed of (230, 300 and
370m/min, feed rate of 0.8, Depth of Cut (DoC) at 0.4m). The
Sometech SV-35 video microscope system used to quantify of the
tool wear. The result shown that tool life span increasing with the
cutting speeds at (370m/min, feed rate of 0.8mm/tooth and DoC at
0.4mm) which constituted an optimum condition for longer tool life
lasted until 123.2 mins. Meanwhile, at medium cutting speed which
at 300m/m, feed rate of 0.8mm/tooth and depth of cut at 0.4mm we
found that tool life span lasted until 119.86 mins while at low cutting
speed it lasted in 119.66 mins. High cutting speed will give the best
parameter in cutting AlSi/AlN MMCs material. The result will help
manufacturers in machining process of AlSi/AlN MMCs materials.
Abstract: The classroom of the 21st century is an ever changing
forum for new and innovative thoughts and ideas. With increasing
technology and opportunity, students have rapid access to
information that only decades ago would have taken weeks to obtain.
Unfortunately, new techniques and technology are not the cure for
the fundamental problems that have plagued the classroom ever since
education was established. Class size has been an issue long debated
in academia. While it is difficult to pin point an exact number, it is
clear that in this case more does not mean better. By looking into the
success and pitfalls of classroom size the true advantages of smaller
classes will become clear. Previously, one class was comprised of 50
students. Being seventeen and eighteen- year- old students,
sometimes it was quite difficult for them to stay focused. To help
them understand and gain much knowledge, a researcher introduced
“The Theory of Multiple Intelligence” and this, in fact, enabled
students to learn according to their own learning preferences no
matter how they were being taught. In this lesson, the researcher
designed a cycle of learning activities involving all intelligences so
that everyone had equal opportunities to learn.
Abstract: We present an analytical model for the calculation of
the sensitivity, the spectral current noise and the detective parameter
for an optically illuminated In0.53Ga0.47As n+nn+ diode. The
photocurrent due to the excess carrier is obtained by solving the
continuity equation. Moreover, the current noise level is evaluated at
room temperature and under a constant voltage applied between the
diode terminals. The analytical calculation of the current noise in the
n+nn+ structure is developed by considering the free carries
fluctuations. The responsivity and the detection parameter are
discussed as functions of the doping concentrations and the emitter
layer thickness in one-dimensional homogeneous n+nn+ structure.
Abstract: In this work, we propose and analyze a model of
Phytoplankton-Zooplankton interaction with harvesting considering
that some species are exploited commercially for food. Criteria for
local stability, instability and global stability are derived and some
threshold harvesting levels are explored to maintain the population
at an appropriate equilibrium level even if the species are exploited
continuously.Further,biological and bionomic equilibria of the system
are obtained and an optimal harvesting policy is also analysed using
the Pantryagin’s Maximum Principle.Finally analytical findings are
also supported by some numerical simulations.
Abstract: Lead being a toxic heavy metal that mankind is
exposed to the highest levels of this metal from environmental
pollutants. A total of 180 Male scalp hair samples were collected
from different environments in Greater Cairo (GC), i.e. industrial,
heavy traffic and rural areas (60 samples from each) having different
activities during the period of, 1/5/2010 to 1/11/2012. Hair samples
were collected during five stages. Data proved that the concentration
of lead in male industrial areas of Cairo ranged between 6.2847 to
19.0432 μg/g, with mean value of 12.3288 μg/g. On the other hand,
lead content of hair samples of residential-traffic areas ranged
between 2.8634 to 16.3311 μg/g with mean value of 9.7552 μg/g.
While lead concentration on the hair of the male residents living in
rural area ranged between 1.0499-9.0402μg/g with mean value of
4.7327 μg/g. The Pb concentration in scalp hair of Cairo residents of
residential-traffic and rural traffic areas was observed to follow the
same pattern. The pattern was that of decrease concentration of
summer and its increase in winter. Then, there was a marked increase
in Pb concentration of summer 2012, and this increase was
significant. These were obviously seen for the residential-traffic and
rural areas residents. Pb pollution in residents of industrial areas
showed the same seasonal pattern, but there was marked to decrease
in Pb concentration of summer 2012, and this decrease was
significant. Lead pollution in residents of GC was serious. It is worth
noting that the atmosphere is still contaminated by lead despite a
decade of using unleaded gasoline. Strong seasonal variation in
higher Pb concentration on winter than in summer was found. Major
contributions to the pollution with Pb could include industry
emissions, motor vehicle emissions and long transported dust from
outside Cairo. More attention should be paid to the reduction of Pb
content of the urban aerosol and to the Pb pollution health.
Abstract: Several of the practical industrial control processes are
multivariable processes. Due to the relation amid the variables
(interaction), delay in the loops, it is very intricate to design a
controller directly for these processes. So first, the interaction of the
variables is analyzed using Relative Normalized Gain Array
(RNGA), which considers the time constant, static gain and delay
time of the processes. Based on the effect of RNGA, relative gain
array (RGA) and NI, the pair (control configuration) of variables to
be controlled by decentralized control is selected. The equivalent
transfer function (ETF) of the process model is estimated as first
order process with delay using the corresponding elements in the
Relative gain array and Relative average residence time array
(RARTA) of the processes. Secondly, a decentralized Proportional-
Integral (PI) controller is designed for each ETF simply using
frequency response specifications. Finally, the performance and
robustness of the algorithm is comparing with existing related
approaches to validate the effectiveness of the projected algorithm.
Abstract: Exact solution of an unsteady flow of elastico-viscous
electrically conducting fluid through a porous media in a tube of
elliptical cross section under the influence of constant pressure
gradient and magnetic field has been obtained in this paper. Initially,
the flow is generated by a constant pressure gradient. After attaining
the steady state, the pressure gradient is suddenly withdrawn and the
resulting fluid motion in a tube of elliptical cross section by taking
into account of the transverse magnetic field and porosity factor of
the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K), magnetic parameter (m) and
elastico-viscosity parameter (β), which depends on the Non-
Newtonian coefficient. The flow parameters are found to be identical
with that of Newtonian case as elastic-viscosity parameter and
magnetic parameter tends to zero and porosity tends to infinity. It is
seen that the effect of elastico-viscosity parameter, magnetic
parameter and the porosity parameter of the bounding surface has
significant effect on the velocity parameter.
Abstract: The demand of high quality services has fueled
dimensional research and development in wireless communications
and networking. As a result, different wireless technologies like
Wireless LAN, CDMA, GSM, UMTS, MANET, Bluetooth and
satellite networks etc. have emerged in the last two decades. Future
networks capable of carrying multimedia traffic need IP convergence,
portability, seamless roaming and scalability among the existing
networking technologies without changing the core part of the
existing communications networks. To fulfill these goals, the present
networking systems are required to work in cooperation to ensure
technological independence, seamless roaming, high security and
authentication, guaranteed Quality of Services (QoS). In this paper, a
conceptual framework for a cooperative network (CN) is proposed
for integration of heterogeneous existing networks to meet out the
requirements of the next generation wireless networks.
Abstract: This study presents an attempt to evaluate the
antioxidant potential and antimicrobial activity of methanolic extract,
and essential oils prepared from the leaves of sage (Salvia officinalis
L.). The content of polyphenol in the methanolic extracts from the
leaves of Salvia officinalis was determined spectrophotometrically,
calculated as gallic acid and catechin equivalent. The essential oils
and methanol extract were also subjected to screenings for the
evaluation of their antioxidant activities using 2, 2-diphenyl-1-
picrylhydrazyl (DPPH) test. While the plant essential oils showed
only weak antioxidant activities, its methanol extract was
considerably active in DPPH (IC50 = 37.29 μg/ml) test. Appreciable
total polyphenol content (31.25 mg/g) was also detected for the plant
methanol extract as gallic acid equivalent in the Folin–Ciocalteu test.
The plant was also screened for its antimicrobial activity and good to
moderate inhibitions were recorded for its essential oils, and
methanol extracts against most of the tested microorganisms.
The present investigation revealed that this plant had rich source
of antioxidant properties. It is for this reason that sage has found
increasing application in food formulations.
Abstract: The growth in the volume of text data such as books
and articles in libraries for centuries has imposed to establish
effective mechanisms to locate them. Early techniques such as
abstraction, indexing and the use of classification categories have
marked the birth of a new field of research called "Information
Retrieval". Information Retrieval (IR) can be defined as the task of
defining models and systems whose purpose is to facilitate access to
a set of documents in electronic form (corpus) to allow a user to find
the relevant ones for him, that is to say, the contents which matches
with the information needs of the user.
Most of the models of information retrieval use a specific data
structure to index a corpus which is called "inverted file" or "reverse
index".
This inverted file collects information on all terms over the corpus
documents specifying the identifiers of documents that contain the
term in question, the frequency of each term in the documents of the
corpus, the positions of the occurrences of the word...
In this paper we use an oriented object database (db4o) instead of
the inverted file, that is to say, instead to search a term in the inverted
file, we will search it in the db4o database.
The purpose of this work is to make a comparative study to see if
the oriented object databases may be competing for the inverse index
in terms of access speed and resource consumption using a large
volume of data.
Abstract: Heavy rare earth (HRE) oxalate concentrates were
prepared from the Egyptian crude monazite sand (graded about 47%).
The concentrates were specified quantitatively for their constituents
of individual rare earth elements using ion chromatograph (IC) and
qualitatively by scanning electron microscope (SEM) for the other
major constituents. The 1st concentrate was composed of 10.5%
HREE where 7.25% of them represented yttrium. The 2nd concentrate
contained about 41.7% LREE, 17.5% HREE and 13.6% Th. The
LREE involved 18.3% Ce, 10.5% La and 8% Nd while the HREE
were 8.7% Y, 3.5% Gd and 2.9% Dy. The 3rd concentrate was
containing about 8.0% LREE (3.7% Ce, 2.0% La and 1.5% Nd),
10.2% HREE (6.4% yttrium and 2.0% Dy) and 2.1% uranium. The
final concentrate comprised 0.84% uranium beside iron, chromium
and traces of REE.
Abstract: The edge waviness in hot rolled steel is a common
defect. Variables that affect such defect include raw material and
machine. These variables are necessary to consider to understand
such defect. This research studied the defect of edge waviness for SS
400 of metal sheet manufacture. Defect of metal sheets were divided
into two groups. The specimens were investigated on chemical
composition and mechanical properties to find the difference. The
results of investigation showed that the difference was not significant.
Therefore the roll mill machine should be used to adjust to support
another location on a roller to avoide edge waviness.
Abstract: In this paper, the dynamic characteristics of a threelobe
journal bearing lubricated with micropolar fluids are determined
by the linear stability theory. Lubricating oil containing additives and
contaminants is modelled as micropolar fluid. The modified
Reynolds equation is obtained using the micropolar lubrication theory
.The finite difference technique has been used to determine the
solution of the modified Reynolds equation. The dynamic
characteristics in terms of stiffness, damping coefficients, the critical
mass and whirl ratio are determined for various values of size of
material characteristic length and the coupling number. The
computed results show that the three-lobe bearing lubricated with
micropolar fluid exhibits better stability compared with that
lubricated with Newtonian fluid. According to the results obtained,
the effect of the parameter micropolar fluid is remarkable on the
dynamic characteristics and stability of the three-lobe bearing.
Abstract: Many of the ever-growing elderly population require
exercise, such as running, for health management. One important
element of a runner’s training is the choice of shoes for exercise; shoes
are important because they provide the interface between the feet and
road. When we purchase shoes, we may instinctively choose a pair
after trying on many different pairs of shoes. Selecting the shoes
instinctively may work, but it does not guarantee a suitable fit for
running activities. Therefore, if we could select suitable shoes for each
runner from the viewpoint of brain activities, it would be helpful for
validating shoe selection. In this paper, we describe how brain
activities show different characteristics during particular task,
corresponding to different properties of shoes. Using five subjects, we
performed a verification experiment, applying weight, softness, and
flexibility as shoe properties. In order to affect the shoe property’s
differences to the brain, subjects run for 10 min. Before and after
running, subjects conducted a paced auditory serial addition task
(PASAT) as the particular task; and the subjects’ brain activities
during the PASAT are evaluated based on oxyhemoglobin and
deoxyhemoglobin relative concentration changes, measured by
near-infrared spectroscopy (NIRS). When the brain works actively,
oxihemoglobin and deoxyhemoglobin concentration drastically
changes; therefore, we calculate the maximum values of concentration
changes. In order to normalize relative concentration changes after
running, the maximum value are divided by before running maximum
value as evaluation parameters. The classification of the groups of
shoes is expressed on a self-organizing map (SOM). As a result,
deoxyhemoglobin can make clusters for two of the three types of
shoes.
Abstract: Reburning is a useful technology in reducing nitric
oxide through injection of a secondary hydrocarbon fuel. In this paper,
an experimental study has been conducted to evaluate the effect of fuel
lean reburning on NOx/CO reduction in LNG flame. Experiments
were performed in flames stabilized by a co-flow swirl burner, which
was mounted at the bottom of the furnace. Tests were conducted using
LNG gas as the reburn fuel as well as the main fuel. The effects of
reburn fuel fraction and injection manner of the reburn fuel were
studied when the fuel lean reburning system was applied. The paper
reports data on flue gas emissions and temperature distribution in the
furnace for a wide range of experimental conditions. At steady state,
temperature distribution and emission formation in the furnace have
been measured and compared. This paper makes clear that in order to
decrease both NOx and CO concentrations in the exhaust when the
pulsated fuel lean reburning system was adapted, it is important that
the control of some factors such as frequency and duty ratio. Also it
shows the fuel lean reburning is also effective method to reduce NOx
as much as reburning.
Abstract: The effect of a 3-dimensional (3D) blade on the turbine
characteristics of Wells turbine for wave energy conversion has been
investigated experimentally by model testing under steady flow
conditions in this study, in order to improve the peak efficiency and
stall characteristics. The aim of use of 3D blade is to prevent flow
separation on the suction surface near the tip. The chord length is
constant with radius and the blade profile changes gradually from the
mean radius to tip. The proposed blade profiles in the study are
NACA0015 from the hub to mean radius and NACA0025 at the tip.
The performances of Wells turbine with 3D blades has been compared
with those of the original Wells turbine, i.e., the turbine with
2-dimensional (2D) blades. As a result, it was concluded that although
the peak efficiency of Wells turbine can be improved by the use of the
proposed 3D blade, its blade does not overcome the weakness of
stalling.