Abstract: This paper presents a study the effect of nose radius
(Rz-mm) on cutting force components and temperatures during the
machining simulation in an orthogonal cutting process for titanium
alloy (Ti-6Al-4V). The cutting process was performed at various
nose radiuses (Rz-mm) while the depth of cut (d-mm), feed rate (fmm/
tooth) and cutting speed (vc-m/ min) were remained constant.
The main cutting force (Fc), feed cutting force (Ft) and temperatures
were estimated by using finite element modeling (FEM) through
ABAQUS/EXPLICIT software and the simulation was developed the
two-dimension via an orthogonal cutting process during machining
titanium alloy (Ti-6Al-4V). The results led to the conclusion that the
nose radius (Rz-mm) has affected directly on the cutting force
components. However, temperature gave no indication or has no
significant relation with nose radius during machining titanium alloy
(Ti-6Al-4V). Hence, any increase or decrease in the nose radius (Rzmm)
during machining operation led to effect on the cutting forces
and thus it will be effective on surface finish, quality, and quantity of
products.
Abstract: Scrubbing by a liquid spraying is one of the most
effective processes used for removal of fine particles and soluble
gas pollutants (such as SO2, HCl, HF) from the flue gas. There are
many configurations of scrubbers designed to provide contact
between the liquid and gas stream for effectively capturing
particles or soluble gas pollutants, such as spray plates, packed bed
towers, jet scrubbers, cyclones, vortex and venturi scrubbers. The
primary function of venturi scrubber is the capture of fine particles
as well as HCl, HF or SO2 removal with effect of the flue gas
temperature decrease before input to the absorption column. In this
paper, sulfur dioxide (SO2) from flue gas was captured using new
design replacing venturi scrubber (1st degree of wet scrubbing).
The flue gas was prepared by the combustion of the carbon
disulfide solution in toluene (1:1 vol.) in the flame in the reactor.
Such prepared flue gas with temperature around 150°C was
processed in designed laboratory O-element scrubber. Water was
used as absorbent liquid. The efficiency of SO2 removal, pressure
drop and temperature drop were measured on our experimental
device. The dependence of these variables on liquid-gas ratio was
observed. The average temperature drop was in the range from
150°C to 40°C. The pressure drop was increased with increasing of
a liquid-gas ratio, but no too much as for the common venturi
scrubber designs. The efficiency of SO2 removal was up to 70 %.
The pressure drop of our new designed wet scrubber is similar to
commonly used venturi scrubbers; nevertheless the influence of
amount of the liquid on pressure drop is not so significant.
Abstract: Testability modeling is a commonly used method in
testability design and analysis of system. A dependency matrix will be
obtained from testability modeling, and we will give a quantitative
evaluation about fault detection and isolation.
Based on the dependency matrix, we can obtain the diagnosis tree.
The tree provides the procedures of the fault detection and isolation.
But the dependency matrix usually includes built-in test (BIT) and
manual test in fact. BIT runs the test automatically and is not limited
by the procedures. The method above cannot give a more efficient
diagnosis and use the advantages of the BIT.
A Comprehensive method of fault detection and isolation is
proposed. This method combines the advantages of the BIT and
Manual test by splitting the matrix. The result of the case study shows
that the method is effective.
Abstract: This paper presents a model for a modified T-junction
device for microspheres generation. The numerical model is
developed using a commercial software package: COMSOL
Multiphysics. In order to test the accuracy of the numerical model,
multiple variables, such as the flow rate of cross-flow, fluid properties,
structure, and geometry of the microdevice are applied. The results
from the model are compared with the experimental results in the
diameter of the microsphere generated. The comparison shows a good
agreement. Therefore the model is useful in further optimization of the
device and feedback control of microsphere generation if any.
Abstract: The aim of this paper is to present the optimization
methodology developed in the frame of a Coastal Transport
Information System. The system will be used for the effective design
of coastal transportation lines and incorporates subsystems that
implement models, tools and techniques that may support the design
of improved networks. The role of the optimization and decision
subsystem is to provide the user with better and optimal scenarios
that will best fulfill any constrains, goals or requirements posed. The
complexity of the problem and the large number of parameters and
objectives involved led to the adoption of an evolutionary method
(Genetic Algorithms). The problem model and the subsystem
structure are presented in detail, and, its support for simulation is also
discussed.
Abstract: Flexible AC Transmission Systems (FACTS) is
granting a new group of advanced power electronic devices emerging
for enhancement of the power system performance. Unified Power
Flow Controller (UPFC) is a recent version of FACTS devices for
power system applications. The back-up energy supply system
incorporated with UPFC is providing a complete control of real and
reactive power at the same time and hence is competent to improve
the performance of an electrical power system. In this article, backup
energy supply unit such as superconducting magnetic energy storage
(SMES) is integrated with UPFC. In addition, comparative
exploration of UPFC–battery, UPFC–UC and UPFC–SMES
performance is evaluated through the vibrant simulation by using
MATLAB/Simulink software.
Abstract: This article presents modeling studies of NiAl alloy
under solid-particle erosion and liquid-drop erosion. In the
solid-particle erosion simulation, attention is paid to the oxide scale
thickness variation on the alloy in high-temperature erosion
environments. The erosion damage is assumed to be deformation wear
and cutting wear mechanisms, incorporating the influence of the oxide
scale on the eroded surface; thus the instantaneous oxide thickness is
the result of synergetic effect of erosion and oxidation. For liquid-drop
erosion, special interest is in investigating the effects of drop velocity
and drop size on the damage of the target surface. The models of
impact stress wave, mean depth of penetration, and maximum depth of
erosion rate (Max DER) are employed to develop various maps for
NiAl alloy, including target thickness vs. drop size (diameter), rate of
mean depth of penetration (MDRP) vs. drop impact velocity, and
damage threshold velocity (DTV) vs. drop size.
Abstract: The hydrodynamics and heat transfer characteristics
of a vaporized elongated bubble in a rectangular microchannel have
been simulated based on Cahn-Hilliard phase-field method. In the
simulations, the initially nucleated bubble starts growing as it comes
in contact with superheated water. The growing shape of the bubble
compared well with the available experimental data in the literature.
Abstract: The problem of toughening in brittle materials
reinforced by fibers is complex, involving all of the mechanical
properties of fibers, matrix and the fiber/matrix interface, as well as
the geometry of the fiber. Development of new numerical methods
appropriate to toughening simulation and analysis is necessary. In
this work, we have performed simulations and analysis of toughening
in brittle matrix reinforced by randomly distributed fibers by means
of the discrete elements method. At first, we put forward a
mechanical model of toughening contributed by random fibers. Then
with a numerical program, we investigated the stress, damage and
bridging force in the composite material when a crack appeared in the
brittle matrix. From the results obtained, we conclude that: (i) fibers
of high strength and low elasticity modulus are beneficial to
toughening; (ii) fibers of relatively high elastic modulus compared to
the matrix may result in substantial matrix damage due to spalling
effect; (iii) employment of high-strength synthetic fibers is a good
option for toughening. We expect that the combination of the discrete
element method (DEM) with the finite element method (FEM) can
increase the versatility and efficiency of the software developed. The
present work can guide the design of ceramic composites of high
performance through the optimization of the parameters.
Abstract: Significant quota of Municipal Electrical Energy
consumption is related to Decentralized Air Conditioning which is
mostly provided by evaporative coolers. So the aim is to optimize
design of air conditioners to increase their efficiencies. To achieve
this goal, results of practical standardized tests for 40 evaporative
coolers in different types collected and simultaneously results for
same coolers based on one of EER (Energy Efficiency Ratio)
modeling styles are figured out. By comparing experimental results
of different coolers standardized tests with modeling results,
preciseness of used model is assessed and after comparing gained
preciseness with international standards based on EER for cooling
capacity, aeration, and also electrical energy consumption, energy
label from A (most effective) to G (less effective) is classified; finally
needed methods to optimize energy consumption and coolers’
classification are provided.
Abstract: Parabolic solar trough systems have seen limited
deployments in cold northern climates as they are more suitable for
electricity production in southern latitudes. A numerical dynamic
model is developed to simulate troughs installed in cold climates and
validated using a parabolic solar trough facility in Winnipeg. The
model is developed in Simulink and will be utilized to simulate a trigeneration
system for heating, cooling and electricity generation in
remote northern communities. The main objective of this simulation
is to obtain operational data of solar troughs in cold climates and use
the model to determine ways to improve the economics and address
cold weather issues.
In this paper the validated Simulink model is applied to simulate a
solar assisted absorption cooling system along with electricity
generation using Organic Rankine Cycle (ORC) and thermal storage.
A control strategy is employed to distribute the heated oil from solar
collectors among the above three systems considering the
temperature requirements. This modelling provides dynamic
performance results using measured meteorological data recorded
every minute at the solar facility location. The purpose of this
modeling approach is to accurately predict system performance at
each time step considering the solar radiation fluctuations due to
passing clouds. Optimization of the controller in cold temperatures is
another goal of the simulation to for example minimize heat losses in
winter when energy demand is high and solar resources are low.
The solar absorption cooling is modeled to use the generated heat
from the solar trough system and provide cooling in summer for a
greenhouse which is located next to the solar field.
The results of the simulation are presented for a summer day in
Winnipeg which includes comparison of performance parameters of
the absorption cooling and ORC systems at different heat transfer
fluid (HTF) temperatures.
Abstract: Groundwater inflow to the tunnels is one of the most
important problems in tunneling operation. The objective of this
study is the investigation of model dimension effects on tunnel inflow
assessment in discontinuous rock masses using numerical modeling.
In the numerical simulation, the model dimension has an important
role in prediction of water inflow rate. When the model dimension is
very small, due to low distance to the tunnel border, the model
boundary conditions affect the estimated amount of groundwater flow
into the tunnel and results show a very high inflow to tunnel. Hence,
in this study, the two-dimensional universal distinct element code
(UDEC) used and the impact of different model parameters, such as
tunnel radius, joint spacing, horizontal and vertical model domain
extent has been evaluated. Results show that the model domain extent
is a function of the most significant parameters, which are tunnel
radius and joint spacing.
Abstract: This paper reports the worldwide status of building
information modeling (BIM) adoption from the perspectives of the
engagement level, the Hype Cycle model, the technology diffusion
model, and BIM services. An online survey was distributed, and 156
experts from six continents responded. Overall, North America was
the most advanced continent, followed by Oceania and Europe.
Countries in Asia perceived their phase mainly as slope of
enlightenment (mature) in the Hype Cycle model. In the technology
diffusion model, the main BIM-users worldwide were “early majority”
(third phase), but those in the Middle East/Africa and South America
were “early adopters” (second phase). In addition, the more advanced
the country, the more number of BIM services employed in general. In
summary, North America, Europe, Oceania, and Asia were advancing
rapidly toward the mature stage of BIM, whereas the Middle
East/Africa and South America were still in the early phase. The
simple indexes used in this study may be used to track the worldwide
status of BIM adoption in long-term surveys.
Abstract: The main goal of this article is to describe the online
flood monitoring and prediction system Floreon+ primarily developed
for the Moravian-Silesian region in the Czech Republic and the basic
process it uses for running automatic rainfall-runoff and
hydrodynamic simulations along with their calibration and
uncertainty modeling. It takes a long time to execute such process
sequentially, which is not acceptable in the online scenario, so the use
of a high performance computing environment is proposed for all
parts of the process to shorten their duration. Finally, a case study on
the Ostravice River catchment is presented that shows actual
durations and their gain from the parallel implementation.
Abstract: Modeling and forecasting dynamics of rainfall
occurrences constitute one of the major topics, which have been
largely treated by statisticians, hydrologists, climatologists and many
other groups of scientists. In the same issue, we propose, in the
present paper, a new hybrid method, which combines Extreme
Values and fractal theories. We illustrate the use of our methodology
for transformed Emberger Index series, constructed basing on data
recorded in Oujda (Morocco).
The index is treated at first by Peaks Over Threshold (POT)
approach, to identify excess observations over an optimal threshold u.
In the second step, we consider the resulting excess as a fractal object
included in one dimensional space of time. We identify fractal
dimension by the box counting. We discuss the prospect descriptions
of rainfall data sets under Generalized Pareto Distribution, assured by
Extreme Values Theory (EVT). We show that, despite of the
appropriateness of return periods given by POT approach, the
introduction of fractal dimension provides accurate interpretation
results, which can ameliorate apprehension of rainfall occurrences.
Abstract: Object-oriented modeling is spreading in current
simulation of physiological systems through the use of the individual
components of the model and its interconnections to define the
underlying dynamic equations. In this paper we describe the use of
both the SIMSCAPE and MODELICA simulation environments in
the object-oriented modeling of the closed loop cardiovascular
system. The performance of the controlled system was analyzed by
simulation in light of the existing hypothesis and validation tests
previously performed with physiological data. The described
approach represents a valuable tool in the teaching of physiology for
graduate medical students.
Abstract: The article deals with modelling of the fire
pragmatism in the area of military management and its experimental
verification. Potential approaches are based on the synergy of
mathematical and theoretical ideas, operational and tactical
requirements and the military decision-making process. This issue
has taken on importance in recent times, particularly with the
increasing trend of digitized battlefield, the development of C4ISR
systems and intention to streamline the command and control process
at the lowest levels of command. From fundamental and
philosophical point of view, these new approaches seek to
significantly upgrade and enhance the decision-making process of the
tactical commanders.
Abstract: This work deals with parameter identification of
permanent magnet motors, a class of ac motor which is particularly
important in industrial automation due to characteristics like
applications high performance, are very attractive for applications
with limited space and reducing the need to eliminate because they
have reduced size and volume and can operate in a wide speed range,
without independent ventilation. By using experimental data and
genetic algorithm we have been able to extract values for both the
motor inductance and the electromechanical coupling constant, which
are then compared to measured and/or expected values.
Abstract: The detection of moving objects from a video image
sequences is very important for object tracking, activity recognition,
and behavior understanding in video surveillance.
The most used approach for moving objects detection / tracking is
background subtraction algorithms. Many approaches have been
suggested for background subtraction. But, these are illumination
change sensitive and the solutions proposed to bypass this problem
are time consuming.
In this paper, we propose a robust yet computationally efficient
background subtraction approach and, mainly, focus on the ability to
detect moving objects on dynamic scenes, for possible applications in
complex and restricted access areas monitoring, where moving and
motionless persons must be reliably detected. It consists of three
main phases, establishing illumination changes invariance,
background/foreground modeling and morphological analysis for
noise removing.
We handle illumination changes using Contrast Limited Histogram
Equalization (CLAHE), which limits the intensity of each pixel to
user determined maximum. Thus, it mitigates the degradation due to
scene illumination changes and improves the visibility of the video
signal. Initially, the background and foreground images are extracted
from the video sequence. Then, the background and foreground
images are separately enhanced by applying CLAHE.
In order to form multi-modal backgrounds we model each channel
of a pixel as a mixture of K Gaussians (K=5) using Gaussian Mixture
Model (GMM). Finally, we post process the resulting binary
foreground mask using morphological erosion and dilation
transformations to remove possible noise.
For experimental test, we used a standard dataset to challenge the
efficiency and accuracy of the proposed method on a diverse set of
dynamic scenes.
Abstract: Unmanned aircraft systems (UAS) are playing
increasingly prominent roles in defense programs and defense
strategies around the world. Technology advancements have
enabled the development of it to do many excellent jobs as
reconnaissance, surveillance, battle fighters, and communications
relays. Simulating a small unmanned aerial vehicle (SUAV)
dynamics and analyzing its behavior at the preflight stage is too
important and more efficient. The first step in the UAV design is
the mathematical modeling of the nonlinear equations of motion. .
In this paper, a survey with a standard method to obtain the full
non-linear equations of motion is utilized, and then the
linearization of the equations according to a steady state flight
condition (trimming) is derived. This modeling technique is
applied to an Ultrastick-25e fixed wing UAV to obtain the valued
linear longitudinal and lateral models. At the end the model is
checked by matching between the behavior of the states of the nonlinear
UAV and the resulted linear model with doublet at the
control surfaces.