Abstract: Over the last few decades, oilfield service rolling
equipment has significantly increased in weight, primarily because of
emissions regulations, which require larger/heavier engines, larger
cooling systems, and emissions after-treatment systems, in some
cases, etc. Larger engines cause more vibration and shock loads,
leading to failure of electronics and control systems.
If the vibrating frequency of the engine matches the system
frequency, high resonance is observed on structural parts and mounts.
One such existing automated control equipment system comprising
wire rope mounts used for mounting computers was designed
approximately 12 years ago. This includes the use of an industrialgrade
computer to control the system operation. The original
computer had a smaller, lighter enclosure. After a few years, a newer
computer version was introduced, which was 10 lbm heavier. Some
failures of internal computer parts have been documented for cases in
which the old mounts were used. Because of the added weight, there
is a possibility of having the two brackets impact each other under
off-road conditions, which causes a high shock input to the computer
parts. This added failure mode requires validating the existing mount
design to suit the new heavy-weight computer.
This paper discusses the modal finite element method (FEM)
analysis and experimental modal analysis conducted to study the
effects of vibration on the wire rope mounts and the computer. The
existing mount was modelled in ANSYS software, and resultant
mode shapes and frequencies were obtained. The experimental modal
analysis was conducted, and actual frequency responses were
observed and recorded.
Results clearly revealed that at resonance frequency, the brackets
were colliding and potentially causing damage to computer parts. To
solve this issue, spring mounts of different stiffness were modeled in
ANSYS software, and the resonant frequency was determined.
Increasing the stiffness of the system increased the resonant
frequency zone away from the frequency window at which the engine
showed heavy vibrations or resonance. After multiple iterations in
ANSYS software, the stiffness of the spring mount was finalized,
which was again experimentally validated.
Abstract: The problematic of gender and socioeconomic status
biased differences in academic motivation patterns is discussed.
Gender identity is understood according to symbolic interactionism
perspective: as a result of reflected appraisals, social comparisons,
self-attributions, and identifications, shaped by social environment
and family context. The effects of socioeconomic status on academic
motivation are conceptualized according to Bourdieu’s habitus
concept, reflecting the role of unconscious and internalized cultural
signals, proper to low and high socioeconomic status family contexts.
Since families differ by various socioeconomic features, the
hypothesis about possible impact of parents’ socioeconomic status on
their children’s academic motivation interfering with gender
socialization effects is held. The survey, aiming to seize gender
differences in academic motivation and self-recorded improvementoriented
efforts as a result of socialization processes operating in the
families of low and high socioeconomic status, was designed. The
results of Lithuanian higher education students’ survey are presented
and discussed.
Abstract: This paper presents nonlinear pulse propagation characteristics for different input optical pulse shapes with various input pulse energy levels in semiconductor optical amplifiers. For simulation of nonlinear pulse propagation, finite-difference beam propagation method is used to solve the nonlinear Schrödinger equation. In this equation, gain spectrum dynamics, gain saturation are taken into account which depends on carrier depletion, carrier heating, spectral-hole burning, group velocity dispersion, self-phase modulation and two photon absorption. From this analysis, we obtained the output waveforms and spectra for different input pulse shapes as well as for different input energies. It shows clearly that the peak position of the output waveforms are shifted toward the leading edge which due to the gain saturation of the SOA for higher input pulse energies. We also analyzed and compared the normalized difference of full-width at half maximum for different input pulse shapes in the SOA.
Abstract: This paper presents a novel design of a microstrip
fractal antenna based on the use of Sierpinski triangle shape, it’s
designed and simulated by using FR4 substrate in the operating
frequency bands (GPS, WiMAX), the design is a fractal antenna with
a modified ground structure. The proposed antenna is simulated and
validated by using CST Microwave Studio Software, the simulated
results presents good performances in term of radiation pattern and
matching input impedance.
Abstract: We present a trigonometric scheme to approximate a
circular arc with its two end points and two end tangents/unit
tangents. A rational cubic trigonometric Bézier curve is constructed
whose end control points are defined by the end points of the circular
arc. Weight functions and the remaining control points of the cubic
trigonometric Bézier curve are estimated by variational approach to
reproduce a circular arc. The radius error is calculated and found less
than the existing techniques.
Abstract: Supply chain (SC) is an operational research (OR)
approach and technique which acts as catalyst within central nervous
system of business today. Without SC, any type of business is at
doldrums, hence entropy. SC is the lifeblood of business today
because it is the pivotal hub which provides imperative competitive
advantage. The paper present a conceptual framework dubbed as
Homomorphic Conceptual Framework for Effective Supply Chain
Strategy (HCEFSC).The term Homomorphic is derived from abstract
algebraic mathematical term homomorphism (same shape) which
also embeds the following mathematical application sets:
monomorphisms, isomorphism, automorphisms, and endomorphism.
The HCFESC is intertwined and integrated with wide and broad sets
of elements.
Abstract: Axial flow fans, while incapable of developing high
pressures, they are well suitable for handling large volumes of air at
relatively low pressures. In general, they are low in cost and possess
good efficiency, and can have blades of airfoil shape. Axial flow fans
show good efficiencies, and can operate at high static pressures if
such operation is necessary. Our objective is to model and analyze
the flow through AXIAL FANS using CFD Software and draw
inference from the obtained results, so as to get maximum efficiency.
The performance of an axial fan was simulated using CFD and the
effect of variation of different parameters such as the blade number,
noise level, velocity, temperature and pressure distribution on the
blade surface was studied. This paper aims to present a final 3D CAD
model of axial flow fan. Adapting this model to the available
components in the market, the first optimization was done. After this
step, CFX flow solver is used to do the necessary numerical analyses
on the aerodynamic performance of this model. This analysis results
in a final optimization of the proposed 3D model which is presented
in this article.
Abstract: The computational fluid dynamics (CFD) study of
stirred tank with the air-water interface are carried out in the presence
of different types of the impeller and with or without baffles. A
multiple reference frame (MRF) approach with the volume of fluid
(VOF) method is used to capture the air-water interface. The RANS
(Reynolds Averaged Navier-Stokes) equations with k-ε turbulence
model are solved to predict the flow behavior of water and air phase
which are treated as a different phases. The predicted results have
shown that the VOF method is able to capture the interface in the
unbaffled tank. While, the VOF method is showing an unfeasible
results in the baffled tank with high rotational impeller speed. For
continuous stirred tank, the air-water interface is disturbed by the
inflow and the level of water is also increased with time.
Abstract: Red blood cells (RBC) are the most common types of
blood cells and are the most intensively studied in cell biology. The
lack of RBCs is a condition in which the amount of hemoglobin level
is lower than normal and is referred to as “anemia”. Abnormalities in
RBCs will affect the exchange of oxygen. This paper presents a
comparative study for various techniques for classifying the RBCs as
normal or abnormal (anemic) using WEKA. WEKA is an open
source consists of different machine learning algorithms for data
mining applications. The algorithms tested are Radial Basis Function
neural network, Support vector machine, and K-Nearest Neighbors
algorithm. Two sets of combined features were utilized for
classification of blood cells images. The first set, exclusively consist
of geometrical features, was used to identify whether the tested blood
cell has a spherical shape or non-spherical cells. While the second
set, consist mainly of textural features was used to recognize the
types of the spherical cells. We have provided an evaluation based on
applying these classification methods to our RBCs image dataset
which were obtained from Serdang Hospital - Malaysia, and
measuring the accuracy of test results. The best achieved
classification rates are 97%, 98%, and 79% for Support vector
machines, Radial Basis Function neural network, and K-Nearest
Neighbors algorithm respectively.
Abstract: The method of introducing the proxy interpretation for
sending and receiving requests increase the capability of the server
and our approach UDIV (User-Data Identity Security) to solve the
data and user authentication without extending size of the data makes
better than hybrid IDS (Intrusion Detection System). And at the same
time all the security stages we have framed have to pass through less
through that minimize the response time of the request. Even though
an anomaly detected, before rejecting it the proxy extracts its identity
to prevent it to enter into system. In case of false anomalies, the
request will be reshaped and transformed into legitimate request for
further response. Finally we are holding the normal and abnormal
requests in two different queues with own priorities.
Abstract: The effect of a 3-dimensional (3D) blade on the turbine
characteristics of Wells turbine for wave energy conversion has been
investigated experimentally by model testing under steady flow
conditions in this study, in order to improve the peak efficiency and
stall characteristics. The aim of use of 3D blade is to prevent flow
separation on the suction surface near the tip. The chord length is
constant with radius and the blade profile changes gradually from the
mean radius to tip. The proposed blade profiles in the study are
NACA0015 from the hub to mean radius and NACA0025 at the tip.
The performances of Wells turbine with 3D blades has been compared
with those of the original Wells turbine, i.e., the turbine with
2-dimensional (2D) blades. As a result, it was concluded that although
the peak efficiency of Wells turbine can be improved by the use of the
proposed 3D blade, its blade does not overcome the weakness of
stalling.
Abstract: In this paper a comprehensive review on various
factory layouts has been carried out for designing a lucrative process
layout for medium scale industries. Industry data base reveals that the
end product rejection rate is on the order of 10% amounting large
profit loss. In order to avoid these rejection rates and to increase the
quality product production an intermediate non-destructive testing
facility (INDTF) has been recommended for increasing the overall
profit. We observed through detailed case studies that while
introducing INDTF to medium scale industries the expensive
production process can be avoided to the defective products well
before its final shape. Additionally, the defective products identified
during the intermediate stage can be effectively utilized for other
applications or recycling; thereby the overall wastage of the raw
materials can be reduced and profit can be increased. We concluded
that the prudent design of a factory layout through critical path
method facilitating with INDTF will warrant profitable outcome.
Abstract: Nanocrystalline powders of the lead-free piezoelectric
material, tantalum-substituted potassium sodium niobate
(K0.5Na0.5)(Nb0.9Ta0.1)O3 (KNNT), were produced using a Retsch
PM100 planetary ball mill by setting the milling time to 15h, 20h,
25h, 30h, 35h and 40h, at a fixed speed of 250rpm. The average
particle size of the milled powders was found to decrease from 12nm
to 3nm as the milling time increases from 15h to 25h, which is in
agreement with the existing theoretical model. An anomalous
increase to 98nm and then a drop to 3nm in the particle size were
observed as the milling time further increases to 30h and 40h
respectively. Various sizes of these starting KNNT powders were
used to investigate the effect of milling time on the microstructure,
dielectric properties, phase transitions and piezoelectric properties of
the resulting KNNT ceramics. The particle size of starting KNNT
was somewhat proportional to the grain size. As the milling time
increases from 15h to 25h, the resulting ceramics exhibit
enhancement in the values of relative density from 94.8% to 95.8%,
room temperature dielectric constant (εRT) from 878 to 1213, and
piezoelectric charge coefficient (d33) from 108pC/N to 128pC/N. For
this range of ceramic samples, grain size refinement suppresses the
maximum dielectric constant (εmax), shifts the Curie temperature (Tc)
to a lower temperature and the orthorhombic-tetragonal phase
transition (Tot) to a higher temperature. Further increase of milling
time from 25h to 40h produces a gradual degradation in the values of
relative density, εRT, and d33 of the resulting ceramics.
Abstract: Floods play a key role in landform evolution of an
area. This process is likely to alter the topography of the earth’s
surface. The present study area, Kota Bharu is very prone to floods
extends from upstream of Kelantan River near Kemubu to the
downstream area near Kuala Besar. These flood events which occur
every year in the study area exhibit a strong bearing on river
morphological set-up. In the present study, three satellite imageries of
different time periods have been used to manifest the post-flood
landform changes. The pre-processing of the images such as subset,
geometric corrections and atmospheric corrections were carried-out
using ENVI 4.5 followed by the analysis processes. Twenty sets of
cross sections were plotted using software Erdas 9.2, ERDAS and
ArcGis 10 for the all three images. The results show a significant
change in the length of the cross section which suggest that the
geomorphological processes play a key role in carving and shaping
the river banks during the floods.
Abstract: This paper proposes a new technique to design a
fixed-structure robust loop shaping controller for the pneumatic
servosystem. In this paper, a new method based on a particle swarm
optimization (PSO) algorithm for tuning the weighting function
parameters to design an H∞ controller is presented. The PSO
algorithm is used to minimize the infinity norm of the transfer
function of the nominal closed loop system to obtain the optimal
parameters of the weighting functions. The optimal stability margin is
used as an objective in PSO for selecting the optimal weighting
parameters; it is shown that the proposed method can simplify the
design procedure of H∞ control to obtain optimal robust controller for
pneumatic servosystem. In addition, the order of the proposed
controller is much lower than that of the conventional robust loop
shaping controller, making it easy to implement in practical works.
Also two-degree-of-freedom (2DOF) control design procedure is
proposed to improve tracking performance in the face of noise and
disturbance. Result of simulations demonstrates the advantages of the
proposed controller in terms of simple structure and robustness
against plant perturbations and disturbances.
Abstract: Regardless of the manufacturing process used,
subtractive or additive, material, purpose and application, produced
components are conventionally solid mass with more or less complex
shape depending on the production technology selected. Aspects
such as reducing the weight of components, associated with the low
volume of material required and the almost non-existent material
waste, speed and flexibility of production and, primarily, a high
mechanical strength combined with high structural performance, are
competitive advantages in any industrial sector, from automotive,
molds, aviation, aerospace, construction, pharmaceuticals, medicine
and more recently in human tissue engineering. Such features,
properties and functionalities are attained in metal components
produced using the additive technique of Rapid Prototyping from
metal powders commonly known as Selective Laser Melting (SLM),
with optimized internal topologies and varying densities. In order to
produce components with high strength and high structural and
functional performance, regardless of the type of application, three
different internal topologies were developed and analyzed using
numerical computational tools. The developed topologies were
numerically submitted to mechanical compression and four point
bending testing. Finite Element Analysis results demonstrate how
different internal topologies can contribute to improve mechanical
properties, even with a high degree of porosity relatively to fully
dense components. Results are very promising not only from the
point of view of mechanical resistance, but especially through the
achievement of considerable variation in density without loss of
structural and functional high performance.
Abstract: This paper focuses on the dynamic behavior of
reinforced concrete (RC) slabs. Therefore, the theoretical modal
analysis was performed using two different types of boundary
conditions. Modal analysis method is the most important dynamic
analyses. The analysis would be modal case when there is no external
force on the structure. By using this method in this paper, the effects
of freely and simply supported boundary conditions on the
frequencies and mode shapes of RC square slabs are studied. ANSYS
software was employed to derive the finite element model to
determine the natural frequencies and mode shapes of the slabs.
Then, the obtained results through numerical analysis (finite element
analysis) would be compared with the exact solution. The main goal
of the research study is to predict how the boundary conditions
change the behavior of the slab structures prior to performing
experimental modal analysis. Based on the results, it is concluded
that simply support boundary condition has obvious influence to
increase the natural frequencies and change the shape of the mode
when it is compared with freely supported boundary condition of
slabs. This means that such support conditions have the direct
influence on the dynamic behavior of the slabs. Thus, it is suggested
to use free-free boundary condition in experimental modal analysis to
precisely reflect the properties of the structure. By using free-free
boundary conditions, the influence of poorly defined supports is
interrupted.
Abstract: A key issue in seismic risk analysis within the context
of Performance-Based Earthquake Engineering is the evaluation of
the expected seismic damage of structures under a specific
earthquake ground motion. The assessment of the seismic
performance strongly depends on the choice of the seismic Intensity
Measure (IM), which quantifies the characteristics of a ground
motion that are important to the nonlinear structural response. Several
conventional IMs of ground motion have been used to estimate their
damage potential to structures. Yet, none of them has been proved to
be able to predict adequately the seismic damage. Therefore,
alternative, scalar intensity measures, which take into account not
only ground motion characteristics but also structural information
have been proposed. Some of these IMs are based on integration of
spectral values over a range of periods, in an attempt to account for
the information that the shape of the acceleration, velocity or
displacement spectrum provides. The adequacy of a number of these
IMs in predicting the structural damage of 3D R/C buildings is
investigated in the present paper. The investigated IMs, some of
which are structure specific and some are non structure-specific, are
defined via integration of spectral values. To achieve this purpose
three symmetric in plan R/C buildings are studied. The buildings are
subjected to 59 bidirectional earthquake ground motions. The two
horizontal accelerograms of each ground motion are applied along
the structural axes. The response is determined by nonlinear time
history analysis. The structural damage is expressed in terms of the
maximum interstory drift as well as the overall structural damage
index. The values of the aforementioned seismic damage measures
are correlated with seven scalar ground motion IMs. The comparative
assessment of the results revealed that the structure-specific IMs
present higher correlation with the seismic damage of the three
buildings. However, the adequacy of the IMs for estimation of the
structural damage depends on the response parameter adopted.
Furthermore, it was confirmed that the widely used spectral
acceleration at the fundamental period of the structure is a good
indicator of the expected earthquake damage level.
Abstract: Particles are the most common and cheapest
reinforcement producing discontinuous reinforced composites with
isotropic properties. Conventional fabrication methods can be used to
produce a wide range of product forms, making them relatively
inexpensive. Optimising composite development must include
consideration of all the fundamental aspect of particles including
their size, shape, volume fraction, distribution and mechanical
properties. Research has shown that the challenges of low fracture
toughness, poor crack growth resistance and low thermal stability can
be overcome by reinforcement with particles. The unique properties
exhibited by micro particles reinforced ceramic composites have
made them to be highly attractive in a vast array of applications.
Abstract: Two Lithium Disilicate (LD) glass ceramics based on
SiO2-Li2O-K2O-Al2O3 system were prepared through a glass melting
method. The glass rods were then fabricated into dental crowns via a
hot pressing at 900˚C and 850˚C in order to study the effect of the
pressing temperatures on the phase formation and microstructure of
the glasses. Different samples of as cast glass and heat treated
samples (600˚C and 700˚C) were used to press for investigating the
effect of an initial microstructure on the hot pressing technique. Xray
diffraction (XRD) and scanning electron microscopy (SEM) were
performed to determine the phase formation and microstructure of the
samples, respectively. XRD results show that the main crystalline
structure was Li2Si2O5 by having Li3PO4, Li0.6Al0.6Si2O6, Li2SiO3,
Ca5 (PO4)3F and SiO2 as minor phases. Glass compositions with
different heat treatment temperatures exhibited a difference phase
formations but have less effect during pressing. SEM micrographs
showed the microstructure of Li2Si2O5 as lath-like shape in all
glasses. With increasing the initial heat treatment temperature, the
longer the lath-like crystals of lithium disilicate were increased
especially when using glass heat treatment at 700˚C followed by
pressing at 900˚C. This could be suggested that LD1 heat treatment at
700˚C which pressing at 900˚C presented the best formation by the
hot pressing and compiled microstructure.