Abstract: This paper aims to determine Fundamental Natural
Frequency (FNF) of a structural composite floor system known as
Chromite. To achieve this purpose, FNFs of studied panels are
determined by development of Finite Element Models (FEMs) in
ABAQUS program. American Institute of Steel Construction (AISC)
code in Steel Design Guide Series 11 presents a fundamental formula
to calculate FNF of a steel framed floor system. This formula has
been used to verify results of the FEMs. The variability in the FNF of
the studied system under various parameters such as dimensions of
floor, boundary conditions, rigidity of main and secondary beams
around the floor, thickness of concrete slab, height of composite
joists, distance between composite joists, thickness of top and bottom
flanges of the open web steel joists, and adding tie beam
perpendicular on the composite joists, is determined. The results
show that changing in dimensions of the system, its boundary
conditions, rigidity of main beam, and also adding tie beam,
significant changes the FNF of the system up to 452.9%, 50.8%, -
52.2%, %52.6%, respectively. In addition, increasing thickness of
concrete slab increases the FNF of the system up to 10.8%.
Furthermore, the results demonstrate that variation in rigidity of
secondary beam, height of composite joist, and distance between
composite joists, and thickness of top and bottom flanges of open
web steel joists insignificant changes the FNF of the studied system
up to -0.02%, -3%, -6.1%, and 0.96%, respectively. Finally, the
results of this study help designer predict occurrence of resonance,
comfortableness, and design criteria of the studied system.
Abstract: Effect of alloying on the microstructure and mechanical properties of heat-resisting duplex stainless steel (DSS) for Mg production was investigated in this study. 25Cr-8Ni based DSS’s were cast into rectangular ingots of which the dimension was 350×350×100 mm3 . Nitrogen and Yttrium were added in the range within 0.3 in weight percent. Phase equilibrium was calculated using the FactSage®, thermodynamic software. Hot exposure, high temperature tensile and compression tests were conducted on the ingots at 1230oC, which is operation temperature employed for Mg production by Silico-thermic reduction. The steel with N and Y showed much higher strength than 310S alloy in both tensile and compression tests. By thermal exposition at 1230oC for 200 hrs, hardness of DSS containing N and Y was found to increase. Hot workability of the heat-resisting DSS was evaluated by employing hot rolling at 1230 oC. Hot shortness was observed in the ingot with N and found to disappear after addition of Y.
Abstract: In this paper, we present a quantum statistical
mechanical formulation from our recently analytical expressions for
partial-wave transition matrix of a three-particle system. We report
the quantum reactive cross sections for three-body scattering
processes 1+(2,3)→1+(2,3) as well as recombination
1+(2,3)→1+(3,1) between one atom and a weakly-bound dimer. The
analytical expressions of three-particle transition matrices and their
corresponding cross-sections were obtained from the threedimensional
Faddeev equations subjected to the rank-two non-local
separable potentials of the generalized Yamaguchi form. The
equilibrium quantum statistical mechanical properties such partition
function and equation of state as well as non-equilibrium quantum
statistical properties such as transport cross-sections and their
corresponding transport collision integrals were formulated
analytically. This leads to obtain the transport properties, such as
viscosity and diffusion coefficient of a moderate dense gas.
Abstract: The purpose of this paper is to examine the effects and
relationship of stress and social support towards the quality of life
among flood victims in Malaysia. A total of 764 respondents took
part in the survey via convenience sampling. The Depression,
Anxiety and Stress scale (DASS) was utilized to measure stress while
The Multidimensional Scale of Perceived Social Support was used to
measure social support. To measure quality of life, the combination
of WHO Quality of Life – BREF (WHOQOL-BREF) and The Impact
of Event Scale – Revised (IES-R) were utilized. The findings of this
study indicate that there were significant correlations between
variables in the study. The findings showed a significant negative
relation between stress and quality of life; and significant positive
correlations between support from family as well as support from
friends with quality of life. Stress and support from family were
found to be significant predictors that influence the quality of life
among flood victims.
Abstract: Wire Electric Discharge Machining (WEDM) is
thermal machining process capable of machining very hard
electrically conductive material irrespective of their hardness.
WEDM is being widely used to machine micro scale parts with the
high dimensional accuracy and surface finish. The objective of this
paper is to optimize the process parameters of wire EDM to fabricate
the micro channels and to calculate the surface finish and material
removal rate of micro channels fabricated using wire EDM. The
material used is aluminum 6061 alloy. The experiments were
performed using CNC wire cut electric discharge machine. The effect
of various parameters of WEDM like pulse on time (TON) with the
levels (100, 150, 200), pulse off time (TOFF) with the levels (25, 35,
45) and current (IP) with the levels (105, 110, 115) were investigated
to study the effect on output parameter i.e. Surface Roughness and
Material Removal Rate (MRR). Each experiment was conducted
under different conditions of pulse on time, pulse off time and peak
current. For material removal rate, TON and Ip
were the most significant process parameter. MRR increases with the increase in
TON and Ip and decreases with the increase in TOFF. For surface
roughness, TON and Ip have the maximum effect and TOFF was found
out to be less effective.
Abstract: We report the design and characterization of ultra high
quality factor filter based on one-dimensional photonic-crystal Thue-
Morse sequence structure. The behavior of aperiodic array of
photonic crystal structure is numerically investigated and we show
that by changing the angle of incident wave, desired wavelengths
could be tuned and a tunable filter is realized. Also it is shown that
high quality factor filter be achieved in the telecommunication
window around 1550 nm, with a device based on Thue-Morse
structure. Simulation results show that the proposed structure has a
quality factor more than 100000 and it is suitable for DWDM
communication applications.
Abstract: The system of ordinary nonlinear differential
equations describing sliding velocity during impact with friction for a
three-dimensional rigid-multibody system is developed. No analytical
solutions have been obtained before for this highly nonlinear system.
Hence, a power series solution is proposed. Since the validity of this
solution is limited to its convergence zone, a suitable time step is
chosen and at the end of it a new series solution is constructed. For a
case study, the trajectory of the sliding velocity using the proposed
method is built using 6 time steps, which coincides with a Runge-
Kutta solution using 38 time steps.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: One of the most important challenging factors in
medical images is nominated as noise. Image denoising refers to the
improvement of a digital medical image that has been infected by
Additive White Gaussian Noise (AWGN). The digital medical image
or video can be affected by different types of noises. They are
impulse noise, Poisson noise and AWGN. Computed tomography
(CT) images are subjects to low quality due to the noise. Quality of
CT images is dependent on absorbed dose to patients directly in such
a way that increase in absorbed radiation, consequently absorbed
dose to patients (ADP), enhances the CT images quality. In this
manner, noise reduction techniques on purpose of images quality
enhancement exposing no excess radiation to patients is one the
challenging problems for CT images processing. In this work, noise
reduction in CT images was performed using two different
directional 2 dimensional (2D) transformations; i.e., Curvelet and
Contourlet and Discrete Wavelet Transform (DWT) thresholding
methods of BayesShrink and AdaptShrink, compared to each other
and we proposed a new threshold in wavelet domain for not only
noise reduction but also edge retaining, consequently the proposed
method retains the modified coefficients significantly that result good
visual quality. Data evaluations were accomplished by using two
criterions; namely, peak signal to noise ratio (PSNR) and Structure
similarity (Ssim).
Abstract: This paper describes how to dimension the electric
components of a 48V hybrid system considering real customer use.
Furthermore, it provides information about savings in energy and
CO2 emissions by a customer-tailored 48V hybrid. Based on measured customer profiles, the electric units such as the
electric motor and the energy storage are dimensioned. Furthermore,
the CO2 reduction potential in real customer use is determined
compared to conventional vehicles. Finally, investigations are carried
out to specify the topology design and preliminary considerations in
order to hybridize a conventional vehicle with a 48V hybrid system.
The emission model results from an empiric approach also taking into
account the effects of engine dynamics on emissions. We analyzed
transient engine emissions during representative customer driving
profiles and created emission meta models. The investigation showed
a significant difference in emissions when simulating realistic
customer driving profiles using the created verified meta models
compared to static approaches which are commonly used for vehicle
simulation.
Abstract: This study presents a hybrid metaheuristic algorithm
to obtain optimum designs for steel space buildings. The optimum
design problem of three-dimensional steel frames is mathematically
formulated according to provisions of LRFD-AISC (Load and
Resistance factor design of American Institute of Steel Construction).
Design constraints such as the strength requirements of structural
members, the displacement limitations, the inter-story drift and the
other structural constraints are derived from LRFD-AISC
specification. In this study, a hybrid algorithm by using teachinglearning
based optimization (TLBO) and harmony search (HS)
algorithms is employed to solve the stated optimum design problem.
These algorithms are two of the recent additions to metaheuristic
techniques of numerical optimization and have been an efficient tool
for solving discrete programming problems. Using these two
algorithms in collaboration creates a more powerful tool and
mitigates each other’s weaknesses. To demonstrate the powerful
performance of presented hybrid algorithm, the optimum design of a
large scale steel building is presented and the results are compared to
the previously obtained results available in the literature.
Abstract: Automation of airport operations can greatly improve
ground movement efficiency. In this paper, we study the speed profile
design problem for advanced airport ground movement control and
guidance. The problem is constrained by the surface four-dimensional
trajectory generated in taxi planning. A decomposed approach of two
stages is presented to solve this problem efficiently. In the first stage,
speeds are allocated at control points, which ensure smooth speed
profiles can be found later. In the second stage, detailed speed profiles
of each taxi interval are generated according to the allocated control
point speeds with the objective of minimizing the overall fuel
consumption. We present a swarm intelligence based algorithm for the
first-stage problem and a discrete variable driven enumeration method
for the second-stage problem, since it only has a small set of discrete
variables. Experimental results demonstrate the presented
methodology performs well on real world speed profile design
problems.
Abstract: Fiber Reinforced Polymer (FRP) is a composite material with exceptional properties that are capable to replace conventional steel reinforcement in reinforced and pre-stressed concrete structures. However, the main obstacle for their wide use in pre-stressed concrete application is the anchorage system. Due to the weakness of FRP in the transverse direction, the pre-stressing capacity of FRP bars are limited. This paper investigates the modification of the conventional wedge anchorage system to be used for stressing of FRP bars in pre-stressed applications. Epoxy adhesive material with glass FRP (GFRP) bars and conventional steel wedge were used in this paper. The GFRP bars are encased with epoxy at the anchor zone and the wedge system was used in pull-out test. The results showed a loading capacity of 47.6 kN which is 69% of the bar ultimate capacity. Additionally, nylon wedge was made with the same dimensions of the steel wedge and tested for GFRP bars without epoxy layer. The nylon wedge showed a loading capacity of 19.7 kN which is only 28.5% of the ultimate bar capacity.
Abstract: The properties of hollow sandcrete blocks produced in
Minna, Nigeria are presented. Sandcrete block is made of cement,
water and sand binded together in certain mix proportions. For the
purpose of this work, fifty (50) commercial sandcrete block industries
were visited in Minna, Nigeria to obtain block samples and
aggregates used for the manufacture, and to take inventory of the mix
composition and the production process. Sieve analysis tests were
conduction on the soil sample from various block industries to
ascertain their quality to be used for block making. The mix ratios
were also investigated. Five (5) nine inches (9’’ or 225mm) blocks
were obtained from each block industry and tested for dimensional
compliance and compressive strength. The results of the soil test
shows that the grading fall within the limit for natural aggregate and
can easily are used to obtain workable mix. Physical examinations of
the block sizes show slight deviation from the standard requirement
in NIS 87:2000. Compressive strength of hollow sandcrete blocks in
range of 0.12 N/mm2 to 0.54 N/mm2 was obtained which is below the
recommendable value of 3.45 N/mm2 for load bearing hollow
sandcrete blocks. This indicates that these blocks are below the
standard for load-bearing sandcrete blocks and cannot be used as load
bearing walling units. The mix composition also indicated low
cement content resulting in low compressive strength. Most of the
commercial block industries visited does not take curing very serious.
Water were only sprinkled ones or twice before the blocks were
stacked and made readily available for sale. It is recommended that a
mix ratio of 1:4 to 1:6 should be used for the production of sandcrete
blocks and proper curing practice should be adhered. Blocks should
also be cured for 14 days before making them available for
consumers.
Abstract: In this article, a new method is proposed for the measuring of well-being inequality through a model composed of superimposing satisfaction waves. The displacement of households’ satisfactory state (i.e. satisfaction) is defined in a satisfaction string. The duration of the satisfactory state for a given period is measured in order to determine the relationship between utility and total satisfactory time, itself dependent on the density and tension of each satisfaction string. Thus, individual cardinal total satisfaction values are computed by way of a one-dimensional form for scalar sinusoidal (harmonic) moving wave function, using satisfaction waves with varying amplitudes and frequencies which allow us to measure wellbeing inequality. One advantage to using satisfaction waves is the ability to show that individual utility and consumption amounts would probably not commute; hence, it is impossible to measure or to know simultaneously the values of these observables from the dataset. Thus, we crystallize the problem by using a Heisenberg-type uncertainty resolution for self-adjoint economic operators. We propose to eliminate any estimation bias by correlating the standard deviations of selected economic operators; this is achieved by replacing the aforementioned observed uncertainties with households’ perceived uncertainties (i.e. corrected standard deviations) obtained through the logarithmic psychophysical law proposed by Weber and Fechner.
Abstract: This paper treats different aspects of entropy measure
in classical information theory and statistical quantum mechanics, it
presents the possibility of extending the definition of Von Neumann
entropy to image and array processing. In the first part, we generalize
the quantum entropy using singular values of arbitrary rectangular
matrices to measure the randomness and the quality of denoising
operation, this new definition of entropy can be implemented to
compare the performance analysis of filtering methods. In the second
part, we apply the concept of pure state in quantum formalism
to generalize the maximum entropy method for narrowband and
farfield source localization problem. Several computer simulation
results are illustrated to demonstrate the effectiveness of the proposed
techniques.
Abstract: This paper discusses the propagation of sound waves in
air, specifically in narrow rectangular pathways of an occluded-ear
simulator for acoustic measurements. In narrow pathways, both the
speed of sound and the phase of the sound waves are affected by the
damping of the air viscosity. Herein, we propose a new finite-element
method (FEM) that considers the effects of the air viscosity. The
method was developed as an extension of existing FEMs for porous,
sound-absorbing materials. The results of a numerical calculation for a
three-dimensional ear-simulator model using the proposed FEM were
validated by comparing with theoretical lumped-parameter modeling
analysis and standard values.
Abstract: The present study applies the inverse method and
three-dimensional CFD commercial software in conjunction with the
experimental temperature data to investigate the heat transfer and fluid
flow characteristics of the plate-fin heat sink in a rectangular closed
enclosure. The inverse method with the finite difference method and
the experimental temperature data is applied to determine the
approximate heat transfer coefficient. Later, based on the obtained
results, the zero-equation turbulence model is used to obtain the heat
transfer and fluid flow characteristics between two fins. T0 validate
the accuracy of the results obtained, the comparison of the heat transfer
coefficient is made. The obtained temperature at selected
measurement locations of the fin is also compared with experimental
data. The effect of the height of the rectangular enclosure on the
obtained results is discussed.
Abstract: A compact Ultra Wide Band (UWB) antenna with coplanar
waveguide feed has been designed and results are verified in
this paper. The antenna has been designed on FR4 substrate with
dielectric constant (εr) of 4.4 and dimensions of 32mm x 26mm x
0.8mm. The presented antenna shows return loss characteristics in the
band of 3.1 to 10.6 GHz as prescribed by FCC, USA. Parametric
studies have been done and results thus obtained have been
presented. Simulated results have been verified on Rohde & Swartz
VNA. The measured results are in good agreement with simulated
results which make the presented antenna suitable to be used for
wearable applications. Performance analysis of antenna has also been
shown in the presence of three layered Human Arm model. Results
obtained in presence of Human Arm model has been compared with
that in free space.
Abstract: This paper is concerned with the single-item
continuous review inventory system in which demand is stochastic
and discrete. The budget consumed for purchasing the ordered items
is not restricted but it incurs extra cost when exceeding specific
value. The unit purchasing price depends on the quantity ordered
under the all-units discounts cost structure. In many actual systems,
the budget as a resource which is occupied by the purchased items is
limited and the system is able to confront the resource shortage by
charging more costs. Thus, considering the resource shortage costs as
a part of system costs, especially when the amount of resource
occupied by the purchased item is influenced by quantity discounts,
is well motivated by practical concerns. In this paper, an optimization
problem is formulated for finding the optimal (r, Q) policy, when the
system is influenced by the budget limitation and a discount pricing
simultaneously. Properties of the cost function are investigated and
then an algorithm based on a one-dimensional search procedure is
proposed for finding an optimal (r, Q) policy which minimizes the
expected system costs.