Abstract: Digital images are widely used in computer
applications. To store or transmit the uncompressed images
requires considerable storage capacity and transmission bandwidth.
Image compression is a means to perform transmission or storage of
visual data in the most economical way. This paper explains about
how images can be encoded to be transmitted in a multiplexing
time-frequency domain channel. Multiplexing involves packing
signals together whose representations are compact in the working
domain. In order to optimize transmission resources each 4 × 4
pixel block of the image is transformed by a suitable polynomial
approximation, into a minimal number of coefficients. Less than
4 × 4 coefficients in one block spares a significant amount of
transmitted information, but some information is lost. Different
approximations for image transformation have been evaluated as
polynomial representation (Vandermonde matrix), least squares +
gradient descent, 1-D Chebyshev polynomials, 2-D Chebyshev
polynomials or singular value decomposition (SVD). Results have
been compared in terms of nominal compression rate (NCR),
compression ratio (CR) and peak signal-to-noise ratio (PSNR)
in order to minimize the error function defined as the difference
between the original pixel gray levels and the approximated
polynomial output. Polynomial coefficients have been later encoded
and handled for generating chirps in a target rate of about two
chirps per 4 × 4 pixel block and then submitted to a transmission
multiplexing operation in the time-frequency domain.
Abstract: This research work is an experimental study, through
development of an adhesive from Prosopis africana endosperm. The
prosopis seed for this work were obtained from Enugu State in the
South East part of Nigeria. The seeds were prepared by separating the
endosperm from the seed coat and cotyledon. Three methods were
used to separate them, which are acidic method, roasting method and
boiling method. 20g of seed were treated with different
concentrations (25, 40, 55, 70, and 85% w/w) at 100°C and constant
time (30 minutes), under continuous stirring with magnetic stirrer.
Also 20g of seed were treated with sulphuric acid of concentrations
40% w/w at 100°C with different time (10, 15, 20, 25, 30 minutes),
under continuous stirring with magnetic stirrer. Finally, 20g of seed
were treated with sulphuric acid of concentrations 40% w/w at
different temperature (20°C, 40°C, 60°C, 80°C, and 100°C) with
constant time (30 minutes), under continuous stirring with magnetic
stirrer. The whole endosperm extracted was adhesive. The physical
properties of the adhesive were determined (appearance, odour, taste,
solubility, pH, size, and binding strength). The percentage of the
adhesive yield makes the commercialization of the seed in Nigeria
possible and profitable. The very high viscosity attained at low
concentrations makes prosopis adhesive an excellent thickener in the
food industry.
Abstract: The aim of this study is to examine, through
experimentation in the laboratory, the supercritical flow in the
presence of an obstacle in a rectangular channel. The supercritical
regime in the whole hydraulic channel is achieved by adding a
convergent. We will observe the influence of the obstacle shape and
dimension on the characteristics of the supercritical flow, mainly the
free-surface elevation and the velocity profile. The velocity
measurements have been conducted with the one dimension laser
anemometry technique.
Abstract: The objective of this study was to examine the
relationship between transformational leadership and innovative work
behavior and to evaluate the mediating role of leader-member
exchange relationships (LMX) on the assumed relationship. This
study has focused on the suggestion that LMX might emerge through
transformational leadership behaviors and thus could mediate the
relationship between transformational leadership and innovative
behavior. A cross-sectional survey research has been conducted on
the relationship these leadership approaches and their impact on
organizational HRM-outcomes have been conducted on two
organizations operating in the technical sector in Istanbul-Turkey.
The results of the research have supported the hypotheses.
Transformational leadership was positively related to the innovative
behaviors and LMX emerged to mediate that relationship.
Abstract: Journal bearings used in IC engines are prone to premature
failures and are likely to fail earlier than the rated life due to
highly impulsive and unstable operating conditions and frequent
starts/stops. Vibration signature extraction and wear debris analysis
techniques are prevalent in industry for condition monitoring of
rotary machinery. However, both techniques involve a great deal of
technical expertise, time, and cost. Limited literature is available on
the application of these techniques for fault detection in reciprocating
machinery, due to the complex nature of impact forces that
confounds the extraction of fault signals for vibration-based analysis
and wear prediction. In present study, a simulation model was developed to investigate
the bearing wear behaviour, resulting because of different operating
conditions, to complement the vibration analysis. In current
simulation, the dynamics of the engine was established first, based on
which the hydrodynamic journal bearing forces were evaluated by
numerical solution of the Reynold’s equation. In addition, the
essential outputs of interest in this study, critical to determine wear
rates are the tangential velocity and oil film thickness between the
journals and bearing sleeve, which if not maintained appropriately,
have a detrimental effect on the bearing performance. Archard’s wear prediction model was used in the simulation to
calculate the wear rate of bearings with specific location information
as all determinative parameters were obtained with reference to crank
rotation. Oil film thickness obtained from the model was used as a
criterion to determine if the lubrication is sufficient to prevent contact
between the journal and bearing thus causing accelerated wear. A
limiting value of 1 μm was used as the minimum oil film thickness
needed to prevent contact. The increased wear rate with growing
severity of operating conditions is analogous and comparable to the
rise in amplitude of the squared envelope of the referenced vibration
signals. Thus on one hand, the developed model demonstrated its
capability to explain wear behaviour and on the other hand it also
helps to establish a co-relation between wear based and vibration
based analysis. Therefore, the model provides a cost effective and
quick approach to predict the impending wear in IC engine bearings
under various operating conditions.
Abstract: Test automation allows performing difficult and time
consuming manual software testing tasks efficiently, quickly and
repeatedly. However, development and maintenance of automated
tests is expensive, so it needs a proper prioritization what to automate
first. This paper describes a simple yet efficient approach for such
prioritization of test cases based on the effort needed for both manual
execution and software test automation. The suggested approach is
very flexible because it allows working with a variety of assessment
methods, and adding or removing new candidates at any time. The
theoretical ideas presented in this article have been successfully
applied in real world situations in several software companies by the
authors and their colleagues including testing of real estate websites,
cryptographic and authentication solutions, OSGi-based middleware
framework that has been applied in various systems for smart homes,
connected cars, production plants, sensors, home appliances, car head
units and engine control units (ECU), vending machines, medical
devices, industry equipment and other devices that either contain or
are connected to an embedded service gateway.
Abstract: Bottom ash from Municipal Solid Waste Incineration
(MSWI) can be viewed as a typical granular material because these
industrial by-products result from the incineration of various
domestic wastes. MSWI bottom ash is mainly used in road
engineering in substitution of the traditional natural aggregates. As
the characterization of their mechanical behavior is essential in order
to use them, specific studies have been led over the past few years. In
the first part of this paper, the mechanical behavior of MSWI bottom
ash is studied with triaxial tests. After, analysis of the experiment
results, the simulation of triaxial tests is carried out by using the
software package CESAR-LCPC. As the first approach in modeling
of this new class material, the Mohr-Coulomb model was chosen to
describe the evolution of material under the influence of external
mechanical actions.
Abstract: The paper presents a method in which the expert
knowledge is applied to fuzzy inference model. Even a less
experienced person could benefit from the use of such a system, e.g.
urban planners, officials. The analysis result is obtained in a very
short time, so a large number of the proposed locations can also be
verified in a short time. The proposed method is intended for testing
of locations of car parks in a city. The paper shows selected examples
of locations of the P&R facilities in cities planning to introduce the
P&R. The analyses of existing objects are also shown in the paper
and they are confronted with the opinions of the system users, with
particular emphasis on unpopular locations. The results of the
analyses are compared to expert analysis of the P&R facilities
location that was outsourced by the city and the opinions about
existing facilities users that were expressed on social networking
sites. The obtained results are consistent with actual users’ feedback.
The proposed method proves to be good, but does not require the
involvement of a large experts team and large financial contributions
for complicated research. The method also provides an opportunity to
show the alternative location of P&R facilities. Although the results
of the method are approximate, they are not worse than results of
analysis of employed experts. The advantage of this method is ease of
use, which simplifies the professional expert analysis. The ability of
analyzing a large number of alternative locations gives a broader
view on the problem. It is valuable that the arduous analysis of the
team of people can be replaced by the model's calculation. According
to the authors, the proposed method is also suitable for
implementation on a GIS platform.
Abstract: Searching the “Island of stability” is a topic of
extreme interest in theoretical as well as experimental modern
physics today. This “island of stability” is spanned by superheavy
elements (SHE's) that are produced in the laboratory. SHE's are
believed to exist primarily due to the “magic” stabilizing effects of
nuclear shell structure. SHE synthesis is extremely difficult due to
their very low production cross section, often of the order of pico
barns or less. Stabilizing effects of shell closures at proton number
Z=82 and neutron number N=126 are predicted theoretically. Though
stabilizing effects of Z=82 have been experimentally verified, no
concluding observations have been made with N=126, so far. We
measured and analyzed the total evaporation residue (ER) cross
sections for a number of systems with neutron number around 126 to
explore possible shell closure effects in ER cross sections, in this
work.
Abstract: Maintenance and design engineers have great concern
for the functioning of rotating machineries due to the vibration
phenomenon. Improper functioning in rotating machinery originates
from the damage to rolling element bearings. The status of rolling
element bearings require advanced technologies to monitor their
health status efficiently and effectively. Avoiding vibration during
machine running conditions is a complicated process. Vibration
simulation should be carried out using suitable sensors/ transducers to
recognize the level of damage on bearing during machine operating
conditions. Various issues arising in rotating systems are interlinked
with bearing faults. This paper presents an approach for fault
diagnosis of bearings using neural networks and time/frequencydomain
vibration analysis.
Abstract: Cochlear Implantation (CI) which became a routine
procedure for the last decades is an electronic device that provides a
sense of sound for patients who are severely and profoundly deaf.
The optimal success of this implantation depends on the electrode
technology and deep insertion techniques. However, this manual
insertion procedure may cause mechanical trauma which can lead to
severe destruction of the delicate intracochlear structure.
Accordingly, future improvement of the cochlear electrode implant
insertion needs reduction of the excessive force application during
the cochlear implantation which causes tissue damage and trauma.
This study is examined tool-tissue interaction of large prototype scale
digit embedded with distributive tactile sensor based upon cochlear
electrode and large prototype scale cochlea phantom for simulating
the human cochlear which could lead to small scale digit
requirements. The digit, distributive tactile sensors embedded with
silicon-substrate was inserted into the cochlea phantom to measure
any digit/phantom interaction and position of the digit in order to
minimize tissue and trauma damage during the electrode cochlear
insertion. The digit have provided tactile information from the digitphantom
insertion interaction such as contact status, tip penetration,
obstacles, relative shape and location, contact orientation and
multiple contacts. The tests demonstrated that even devices of such a
relative simple design with low cost have potential to improve
cochlear implant surgery and other lumen mapping applications by
providing tactile sensory feedback information and thus controlling
the insertion through sensing and control of the tip of the implant
during the insertion. In that approach, the surgeon could minimize the
tissue damage and potential damage to the delicate structures within
the cochlear caused by current manual electrode insertion of the
cochlear implantation. This approach also can be applied to other
minimally invasive surgery applications as well as diagnosis and path
navigation procedures.
Abstract: The main objective of this research is to describe the
relationship between organizational climate and organizational
citizenship behavior. In order to examine this relationship, a research
is intended to be carried out in relevant institutions and organizations
operating in the health sector in Turkey. It will be researched that
whether there is a statistically significant relationship between
organizational climate and organizational citizenship behavior
through elated scientific research methods and statistical analysis. In
addition, relationships between the dimensions of organizational
climate and organizational citizenship behavior subscales will be
questioned statistically.
Abstract: The statistical study has become indispensable for various fields of knowledge. Not any different, in Geotechnics the study of probabilistic and statistical methods has gained power considering its use in characterizing the uncertainties inherent in soil properties. One of the situations where engineers are constantly faced is the definition of a probability distribution that represents significantly the sampled data. To be able to discard bad distributions, goodness-of-fit tests are necessary. In this paper, three non-parametric goodness-of-fit tests are applied to a data set computationally generated to test the goodness-of-fit of them to a series of known distributions. It is shown that the use of normal distribution does not always provide satisfactory results regarding physical and behavioral representation of the modeled parameters.
Abstract: The purpose of this study is analyzing the relationship
between trust and social capital of people with using Social Network
Analysis. In this study, two aspects of social capital will be focused:
Bonding, homophilous social capital (BoSC), and Bridging,
heterophilous social capital (BrSC). These two aspects diverge each
other regarding to the social theories. The other concept of the study
is Trust (Tr), namely interpersonal trust, willing to ascribe good
intentions to and have confidence in the words and actions of other
people. In this study, the sample group, 61 people, was selected from
a private firm from the defense industry. The relation between
BoSC/BrSC and Tr is shown by using Social Network Analysis
(SNA) and statistical analysis with Likert type-questionnaire. The
results of the analysis show the Cronbach’s alpha value is 0.756 and
social capital values (BoSC/BrSC) is not correlated with Tr values of
the people.
Abstract: The occurrences of precipitation, also commonly
referred as rain, in the form of "convective" and "stratiform" have
been identified to exist worldwide. In this study, the radar return
echoes or known as reflectivity values acquired from radar scans
have been exploited in the process of classifying the type of rain
endured. The investigation use radar data from Malaysian
Meteorology Department (MMD). It is possible to discriminate the
types of rain experienced in tropical region by observing the vertical
characteristics of the rain structure. .Heavy rain in tropical region
profoundly affects radiowave signals, causing transmission
interference and signal fading. Required wireless system fade margin
depends on the type of rain. Information relating to the two
mentioned types of rain is critical for the system engineers and
researchers in their endeavour to improve the reliability of
communication links. This paper highlights the quantification of
percentage occurrences over one year period in 2009.
Abstract: Genetic algorithm is widely used in optimization
problems for its excellent global search capabilities and highly parallel
processing capabilities; but, it converges prematurely and has a poor
local optimization capability in actual operation. Simulated annealing
algorithm can avoid the search process falling into local optimum. A
hybrid genetic algorithm based on simulated annealing is designed by
combining the advantages of genetic algorithm and simulated
annealing algorithm. The numerical experiment represents the hybrid
genetic algorithm can be applied to solve the function optimization
problems efficiently.
Abstract: In this study, Brillouin Gain Spectrum (BGS) is
experimentally analyzed in the Brillouin Optical Time Domain
Reflectometry (BOTDR) and Brillouin Optical Time Domain
Analyzer (BOTDA). For this purpose, the signal level of the
microwave generator is varied and the effects of BGS are
investigated. In the setups, 20 km conventional single mode fiber is
used to both setups and laser wavelengths are selected around 1550
nm. To achieve best results, it can be used between 5 dBm to 15 dBm
signal level of microwave generator for BOTDA and BOTDR setups.
Abstract: The social logic of 'Sequina' slum area in Alexandria details the integral measure of space syntax at the room-level of twenty-building samples. The essence of spatial structure integrates the central 'visitor' domain with the 'living' frontage of the 'children' zone against the segregated privacy of the opposite 'parent' depth. Meanwhile, the multifunctioning of shallow rooms optimizes the integral 'visitor' structure through graph and visibility dimensions in contrast to the 'inhabitant' structure of graph-tails out of sight. Common theme of the layout integrity increases in compensation to the decrease of room visibility. Despite the 'pheno-type' of collective integration, the individual layouts observe 'geno-type' structure of spatial diversity per room adjoins. In this regard, the layout integrity alternates the cross-correlation of the 'kitchen & living' rooms with the 'inhabitant & visitor' domains of 'motherhood' dynamic structure. Moreover, the added 'grandparent' restructures the integral measure to become the deepest space, but opens to the 'living' of 'household' integrity. Some isomorphic layouts change the integral structure just through the 'balcony' extension of access, visual or ignored 'ringiness' of space syntax. However, the most integrated or segregated layouts invert the 'geno-type' into a shallow 'inhabitant' centrality versus the remote 'visitor' structure. Overview of the multivariate social logic of spatial integrity could never clarify without the micro-data analysis.
Abstract: Lightweight and efficient structures have the aim to
enhance the efficiency of the components in various industries.
Toward this end, composites are one of the most widely used
materials because of durability, high strength and modulus, and low
weight. One type of the advanced composites is grid-stiffened
composite (GSC) structures, which have been extensively considered
in aerospace, automotive, and aircraft industries. They are one of the
top candidates for replacing some of the traditional components,
which are used here. Although there are a good number of published
surveys on the design aspects and fabrication of GSC structures, little
systematic work has been reported on their material modification to
improve their properties, to our knowledge. Matrix modification
using nanoparticles is an effective method to enhance the flexural
properties of the fibrous composites. In the present study, a silanecoupling
agent (3-glycidoxypropyltrimethoxysilane/3-GPTS) was
introduced onto the silica (SiO2) nanoparticle surface and its effects
on the three-point flexural response of isogrid E-glass/epoxy
composites were assessed. Based on the Fourier Transform Infrared
Spectrometer (FTIR) spectra, it was inferred that the 3-GPTS
coupling agent was successfully grafted onto the surface of SiO2
nanoparticles after modification. Flexural test revealed an
improvement of 16%, 14%, and 36% in stiffness, maximum load and
energy absorption of the isogrid specimen filled with 3 wt.% 3-
GPTS/SiO2 compared to the neat one. It would be worth mentioning
that in these structures, considerable energy absorption was observed
after the primary failure related to the load peak. In addition, 3-
GPTMS functionalization had a positive effect on the flexural
behavior of the multiscale isogrid composites. In conclusion, this
study suggests that the addition of modified silica nanoparticles is a
promising method to improve the flexural properties of the gridstiffened
fibrous composite structures.
Abstract: Mineral product, waste concrete (fine aggregates),
waste in the optical field, industry, and construction employ separators
to separate solids and classify them according to their size. Various
sorting machines are used in the industrial field such as those operating
under electrical properties, centrifugal force, wind power, vibration,
and magnetic force. Study on separators has been carried out to
contribute to the environmental industry. In this study, we perform
CFD analysis for understanding the basic mechanism of the separation
of waste concrete (fine aggregate) particles from air with a machine
built with a rotor with blades. In CFD, we first performed
two-dimensional particle tracking for various particle sizes for the
model with 1 degree, 1.5 degree, and 2 degree angle between each
blade to verify the boundary conditions and the method of rotating
domain method to be used in 3D. Then we developed 3D numerical
model with ANSYS CFX to calculate the air flow and track the
particles. We judged the capability of particle separation for given size
by counting the number of particles escaping from the domain toward
the exit among 10 particles issued at the inlet. We confirm that
particles experience stagnant behavior near the exit of the rotating
blades where the centrifugal force acting on the particles is in balance
with the air drag force. It was also found that the minimum particle
size that can be separated by the machine with the rotor is determined
by its capability to stay at the outlet of the rotor channels.