Abstract: Low carbon deep drawing steel DC 01 according to EN 10130-91 was nitrooxidized in dissociated ammonia at 580°C/45 min and consequently oxidised at 380°C/5 min in vapour of distilled water. Material after nitrooxidation had 54 % increase of yield point, 34 % increase of strength and 10-times increased resistance to atmospheric corrosion in comparison to the material before nitrooxidation. The microstructure of treated material consisted of thin ε-phase layer connected to layer containing precipitated massive needle shaped Fe4N - γ' nitrides. This layer passed to a diffusion layer consisting of fine irregular shaped Fe16N2 - α'' nitrides regularly dispersed in ferritic matrix. Fatigue properties were examined under bending load with frequency of 20 kHz and sinusoidal symmetric cycle. The results confirmed positive influence of nitrooxidation on fatigue properties as fatigue limit of treated material was double in comparison to untreated material.
Abstract: This paper addresses an efficient technique to embed and detect digital fingerprint code. Orthogonal modulation method is a straightforward and widely used approach for digital fingerprinting but shows several limitations in computational cost and signal efficiency. Coded modulation method can solve these limitations in theory. However it is difficult to perform well in practice if host signals are not available during tracing colluders, other kinds of attacks are applied, and the size of fingerprint code becomes large. In this paper, we propose a hybrid modulation method, in which the merits of or-thogonal modulation and coded modulation method are combined so that we can achieve low computational cost and high signal efficiency. To analyze the performance, we design a new fingerprint code based on GD-PBIBD theory and modulate this code into images by our method using spread-spectrum watermarking on frequency domain. The results show that the proposed method can efficiently handle large fingerprint code and trace colluders against averaging attacks.
Abstract: Conventional approaches in the implementation of logic programming applications on embedded systems are solely of software nature. As a consequence, a compiler is needed that transforms the initial declarative logic program to its equivalent procedural one, to be programmed to the microprocessor. This approach increases the complexity of the final implementation and reduces the overall system's performance. On the contrary, presenting hardware implementations which are only capable of supporting logic programs prevents their use in applications where logic programs need to be intertwined with traditional procedural ones, for a specific application. We exploit HW/SW codesign methods to present a microprocessor, capable of supporting hybrid applications using both programming approaches. We take advantage of the close relationship between attribute grammar (AG) evaluation and knowledge engineering methods to present a programmable hardware parser that performs logic derivations and combine it with an extension of a conventional RISC microprocessor that performs the unification process to report the success or failure of those derivations. The extended RISC microprocessor is still capable of executing conventional procedural programs, thus hybrid applications can be implemented. The presented implementation is programmable, supports the execution of hybrid applications, increases the performance of logic derivations (experimental analysis yields an approximate 1000% increase in performance) and reduces the complexity of the final implemented code. The proposed hardware design is supported by a proposed extended C-language called C-AG.
Abstract: Dynamic of phytoplankton blooms in the Baltic Sea
has been analyzed applying the numerical ecosystem model 3D
CEMBS. The model consists of the hydrodynamic model (POP,
version 2.1) and the ice model (CICE, version 4.0), which are
imposed by the atmospheric data model (DATM7). The 3D
model has an ecosystem module, activated in 2012 in the operational
mode. The ecosystem model consists of 11 main variables: biomass
of small-size phytoplankton and large-size phytoplankton
and cyanobacteria, zooplankton biomass, dissolved and molecular
detritus, dissolved oxygen concentration, as well as concentrations of
nutrients, including: nitrates, ammonia, phosphates and silicates. The
3D-CEMBS model is an effective tool for solving problems related to
phytoplankton blooms dynamic in the Baltic Sea
Abstract: Full adders are important components in applications
such as digital signal processors (DSP) architectures and
microprocessors. In addition to its main task, which is adding two
numbers, it participates in many other useful operations such as
subtraction, multiplication, division,, address calculation,..etc. In
most of these systems the adder lies in the critical path that
determines the overall speed of the system. So enhancing the
performance of the 1-bit full adder cell (the building block of the
adder) is a significant goal.Demands for the low power VLSI have
been pushing the development of aggressive design methodologies to
reduce the power consumption drastically. To meet the growing
demand, we propose a new low power adder cell by sacrificing the
MOS Transistor count that reduces the serious threshold loss
problem, considerably increases the speed and decreases the power
when compared to the static energy recovery full (SERF) adder. So a
new improved 14T CMOS l-bit full adder cell is presented in this
paper. Results show 50% improvement in threshold loss problem,
45% improvement in speed and considerable power consumption
over the SERF adder and other different types of adders with
comparable performance.
Abstract: In this work we present some matrix operators named
circulant operators and their action on square matrices. This study on
square matrices provides new insights into the structure of the space
of square matrices. Moreover it can be useful in various fields as in
agents networking on Grid or large-scale distributed self-organizing
grid systems.
Abstract: The purpose of this research is to study motivation
factors and also to study factors relation to job performance to
compare motivation factors under the personal factor classification
such as gender, age, income, educational level, marital status, and
working duration; and to study the relationship between Motivation
Factors and Job Performance with job satisfactions. The sample
groups utilized in this research were 400 Suan Sunandha Rajabhat
University employees. This research is a quantitative research using
questionnaires as research instrument. The statistics applied for data
analysis including percentage, mean, and standard deviation. In
addition, the difference analysis was conducted by t value computing,
one-way analysis of variance and Pearson’s correlation coefficient
computing. The findings of the study results were as follows the
findings showed that the aspects of job promotion and salary were at
the moderate levels. Additionally, the findings also showed that the
motivations that affected the revenue branch chiefs’ job performance
were job security, job accomplishment, policy and management, job
promotion, and interpersonal relation.
Abstract: Malaria is transmitted to the human by biting of
infected Anopheles mosquitoes. This disease is a serious, acute and
chronic relapsing infection to humans. Fever, nausea, vomiting, back
pain, increased sweating anemia and splenomegaly (enlargement of
the spleen) are the symptoms of the patients who infected with this
disease. It is caused by the multiplication of protozoa parasite of the
genus Plasmodium. Plasmodium falciparum, Plasmodium vivax,
Plasmodium malariae and Plasmodium ovale are the four types of
Plasmodium malaria. A mathematical model for the transmission of
Plasmodium Malaria is developed in which the human and vector
population are divided into two classes, the susceptible and the
infectious classes. In this paper, we formulate the dynamical model
of Plasmodium falciparum and Plasmodium vivax malaria. The
standard dynamical analysis is used for analyzing the behavior for
the transmission of this disease. The Threshold condition is found
and numerical results are shown to confirm the analytical results.
Abstract: In this paper, by using Mawhin-s continuation theorem of coincidence degree and a method based on delay differential inequality, some sufficient conditions are obtained for the existence and global exponential stability of periodic solutions of cellular neural networks with distributed delays and impulses on time scales. The results of this paper generalized previously known results.
Abstract: The process of wafer fabrication is arguably the most
technologically complex and capital intensive stage in semiconductor
manufacturing. This large-scale discrete-event process is highly reentrant,
and involves hundreds of machines, restrictions, and
processing steps. Therefore, production control of wafer fabrication
facilities (fab), specifically scheduling, is one of the most challenging
problems that this industry faces. Dispatching rules have been
extensively applied to the scheduling problems in semiconductor
manufacturing. Moreover, lot release policies are commonly used in
this manufacturing setting to further improve the performance of such
systems and reduce its inherent variability. In this work, simulation is
used in the scheduling of re-entrant flow shop manufacturing systems
with an application in semiconductor wafer fabrication; where, a
simulation model has been developed for the Intel Five-Machine Six
Step Mini-Fab using the ExtendTM simulation environment. The
Mini-Fab has been selected as it captures the challenges involved in
scheduling the highly re-entrant semiconductor manufacturing lines.
A number of scenarios have been developed and have been used to
evaluate the effect of different dispatching rules and lot release
policies on the selected performance measures. Results of simulation
showed that the performance of the Mini-Fab can be drastically
improved using a combination of dispatching rules and lot release
policy.
Abstract: Supplier selection, in real situation, is affected by
several qualitative and quantitative factors and is one of the most
important activities of purchasing department. Since at the time of
evaluating suppliers against the criteria or factors, decision makers
(DMS) do not have precise, exact and complete information, supplier
selection becomes more difficult. In this case, Grey theory helps us
to deal with this problem of uncertainty. Here, we apply Technique
for Order Preference by Similarity to Ideal Solution (TOPSIS)
method to evaluate and select the best supplier by using interval
fuzzy numbers. Through this article, we compare TOPSIS with some
other approaches and afterward demonstrate that the concept of
TOPSIS is very important for ranking and selecting right supplier.
Abstract: The electrolyte stirring method of anodization etching
process for manufacturing porous silicon (PS) is reported in this work.
Two experimental setups of nature air stirring (PS-ASM) and
electrolyte stirring (PS-ESM) are employed to clarify the influence of
stirring mechanisms on electrochemical etching process. Compared to
traditional fabrication without any stirring apparatus (PS-TM), a large
plateau region of PS surface structure is obtained from samples with
both stirring methods by the 3D-profiler measurement. Moreover, the
light emission response is also improved by both proposed electrolyte
stirring methods due to the cycling force in electrolyte could
effectively enhance etch-carrier distribution while the electrochemical
etching process is made. According to the analysis of statistical
calculation of photoluminescence (PL) intensity, lower standard
deviations are obtained from PS-samples with studied stirring methods,
i.e. the uniformity of PL-intensity is effectively improved. The
calculated deviations of PL-intensity are 93.2, 74.5 and 64,
respectively, for PS-TM, PS-ASM and PS-ESM.
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.
Abstract: Five original strains of entomopathogenic bacteria
with insecticidal activity against mosquito larvae of the genera Aedes,
Culex and Anopheles have been isolated from natural conditions in
Armenia and characterized. According to morphological,
physiological and biochemical parameters, all isolates were identified
as Bacillus thuringiensis spp. israelensis (Bti). High larvicidal
activity has been showed by three strains Bti. These strains can be
recommended for industrial production of bacterial preparations.
Abstract: Supplementation of palm vitamin E has been reported
to prevent loss of bone density in ovariectomised female rats. The
mechanism by which palm vitamin E exerts these effects is still
unknown. We hypothesized that palm vitamin E may act by
preventing the protein expression changes. Two dimensional poly
acyrilamide gel electrophoresis (2-D PAGE) and PD Quest software
genomic solutions Investigator (proteomics) was used to analyze the
differential protein expression profile in femoral and humeri bones
harvested from three groups of rats; sham-operated rats (SO),
ovariectomised rats (Ovx) and ovariectomised rats supplemented for
2 months with palm vitamin E. The results showed that there were
over 300 valued spot on each of the groups PVE and OVX as
compared to about 200 in SO. Comparison between the differential
protein expression between OVX and PVE groups showed that ten
spots were down –regulated in OVX but up-regulated in PVE. The
ten differential spots were separately named P1-P10. The
identification and understanding of the pathway of the differential
protein expression among the groups is ongoing and may account for
the molecular mechanism through which palm vitamin E exert its
anti-osteoporotic effect.
Abstract: Traffic enforcement units (the Police) are partly
responsible for the severity and frequency of the traffic accidents via
the effectiveness of their safety measures. The Police claims that the
reductions in accidents and their severities occur largely by their
timely interventions at the black spots, through traffic management
or temporary changes in the road design (guiding, reducing speeds
and eliminating sight obstructions, etc.). Yet, some other external
factors than the Police measures may intervene into which such
claims require a statistical confirmation. In order to test the net
impact of the Police contribution in the reduction of the number of
crashes, Chi square test was applied for 25 spots (streets and
intersections) and an average evaluation was achieved for general
conclusion in the case study of Izmir city. Separately, the net impact
of economic crisis in the reduction of crashes is assessed by the
trend analysis for the case of the economic crisis with the probable
reduction effects on the trip generation or modal choice. Finally, it
was proven that the Police measures were effective to some degree as
they claimed, though the economic crisis might have only negligible
contribution to the reductions in the same period observed.
Abstract: Serial Analysis of Gene Expression is a powerful
quantification technique for generating cell or tissue gene expression
data. The profile of the gene expression of cell or tissue in several
different states is difficult for biologists to analyze because of the large
number of genes typically involved. However, feature selection in
machine learning can successfully reduce this problem. The method
allows reducing the features (genes) in specific SAGE data, and
determines only relevant genes. In this study, we used a genetic
algorithm to implement feature selection, and evaluate the
classification accuracy of the selected features with the K-nearest
neighbor method. In order to validate the proposed method, we used
two SAGE data sets for testing. The results of this study conclusively
prove that the number of features of the original SAGE data set can be
significantly reduced and higher classification accuracy can be
achieved.
Abstract: Twenty seven tektites from the Wenchang area, Hainan
province (south China) and five tektites from the Khon Kaen area
(northeast Thailand) were analyzed for major and trace element
contents and Rb-Sr isotopic compositions. All the samples studied are
splash-form tektites. Tektites of this study are characterized by high
SiO2 contents ranging from 71.95 to 74.07 wt% which is consistent
with previously published analyses of Australasian tektites. The trace
element ratios Ba/Rb (avg. 3.89), Th/Sm (avg. 2.40), Sm/Sc (avg.
0.45), Th/Sc (avg. 0.99) and the rare earth elements (REE) contents of
tektites of this study are similar to the average upper continental crust.
Based on the chemical composition, it is suggested that tektites in this
study are derived from similar parental material and are similar to the
post-Archean upper crustal rocks. The major and trace element
abundances of tektites analyzed indicate that the parental material of
tektites may be a terrestrial sedimentary deposit. The tektites from the
Wenchang area, Hainan Island have high positive εSr(0)
values-ranging from 184.5~196.5 which indicate that the parental
material for these tektites have similar Sr isotopic compositions to old
terrestrial sedimentary rocks and they were not dominantly derived
from recent young sediments (such as soil or loess). Based on Rb-Sr
isotopic data, it has been suggested by Blum (1992) [1]that the
depositional age of sedimentary target materials is close to 170Ma
(Jurassic). According to the model suggested by Ho and Chen
(1996)[2], mixing calculations for various amounts and combinations
of target rocks have been carried out. We consider that the best fit for
tektites from the Wenchang area is a mixture of 47% shale, 23%
sandstone, 25% greywacke and 5% quartzite, and the other tektites
from Khon Kaen area is a mixture of 46% shale, 2% sandstone, 20%
greywacke and 32% quartzite.
Abstract: Acute disseminated encephalomyelitis (ADEM) has
been reported to develop after a hymenoptera sting, but its
pathogenesis is not known in detail. Myelin basic protein (MBP)-
specific T cells have been detected in the blood of patients with
ADEM, and a proportion of these patients develop multiple sclerosis
(MS). In an attempt to understand the mechanisms underlying
ADEM, molecular mimicry between hymenoptera venom peptides
and the human immunodominant MBP peptide was scrutinized,
based on the sequence and structural similarities, whether it was the
root of the disease. The results suggest that the three wasp venom
peptides have low sequence homology with the human
immunodominant MBP residues 85-99. Structural similarity analysis
among the three venom peptides and the MS-related HLA-DR2b
(DRA, DRB1*1501)-associated immunodominant MHC
binding/TCR contact residues 88-93, VVHFFK showed that
hyaluronidase residues 7-12, phospholipase A1 residues 98-103, and
antigen 5 residues 109-114 showed a high degree of similarity
83.3%, 100%, and 83.3% respectively. In conclusion, some wasp
venom peptides, particularly phospholipase A1, may potentially act
as the molecular motifs of the human 3HLA-DR2b-associated
immunodominant MBP88-93, and possibly present a mechanism for
induction of wasp sting-associated ADEM.
Abstract: Today, the preferences and participation of the TD groups such as the elderly and disabled is still lacking in decision-making of transportation planning, and their reactions to certain type of policies are not well known. Thus, a clear methodology is needed. This study aimed to develop a method to extract the preferences of the disabled to be used in the policy-making stage that can also guide to future estimations. The method utilizes the combination of cluster analysis and data filtering using the data of the Arao city (Japan). The method is a process that follows: defining the TD group by the cluster analysis tool, their travel preferences in tabular form from the household surveys by policy variableimpact pairs, zones, and by trip purposes, and the final outcome is the preference probabilities of the disabled. The preferences vary by trip purpose; for the work trips, accessibility and transit system quality policies with the accompanying impacts of modal shifts towards public mode use as well as the decreasing travel costs, and the trip rate increase; for the social trips, the same accessibility and transit system policies leading to the same mode shift impact, together with the travel quality policy area leading to trip rate increase. These results explain the policies to focus and can be used in scenario generation in models, or any other planning purpose as decision support tool.