Abstract: Recently, as the scale of construction projects has
increases, more ground excavation for foundations is carried out than ever before. Consequently, damage to underground ducts (gas, water/sewage or oil pipelines, communication cables or power cable ducts) or superannuated pipelines frequently cause serious accidents
resulting in damage to life and property. (In Korea, the total length of city water pipelines was approximately 2,000 km as of the end of 2009.) In addition, large amounts of damage caused by fractures, water
and gas leakage caused by superannuation or damage to underground
ducts in construction has been reported. Therefore, a system is required to precisely detect defects and deterioration in underground
pipelines and the locations of such defects, for timely and accurate
maintenance or replacement of the ducts. In this study, a system was
developed which can locate underground structures (gas and water
pipelines, power cable ducts, etc.) in 3D-coordinates and monitor the
degree and position of defects using an Inertial Measurement Unit
(IMU) sensing technique. The system can prevent damage to underground ducts and superannuated pipelines during construction,
and provide reliable data for maintenance. The utility of the IMU sensing technique used in aircraft and ships in civil applications was
verified.
Abstract: The general idea behind the filter is to average a pixel
using other pixel values from its neighborhood, but simultaneously to
take care of important image structures such as edges. The main
concern of the proposed filter is to distinguish between any variations
of the captured digital image due to noise and due to image structure.
The edges give the image the appearance depth and sharpness. A
loss of edges makes the image appear blurred or unfocused.
However, noise smoothing and edge enhancement are traditionally
conflicting tasks. Since most noise filtering behaves like a low pass
filter, the blurring of edges and loss of detail seems a natural
consequence. Techniques to remedy this inherent conflict often
encompass generation of new noise due to enhancement.
In this work a new fuzzy filter is presented for the noise reduction
of images corrupted with additive noise. The filter consists of three
stages. (1) Define fuzzy sets in the input space to computes a fuzzy
derivative for eight different directions (2) construct a set of IFTHEN
rules by to perform fuzzy smoothing according to
contributions of neighboring pixel values and (3) define fuzzy sets in
the output space to get the filtered and edged image.
Experimental results are obtained to show the feasibility of the
proposed approach with two dimensional objects.
Abstract: The accelerated sonophotocatalytic degradation of
Reactive Red (RR) 120 dye under visible light using dye sensitized
TiO2 activated by ultrasound has been carried out. The effect of
sonolysis, photocatalysis and sonophotocatalysis under visible light
has been examined to study the influence on the degradation rates by
varying the initial substrate concentration, pH and catalyst loading to
ascertain the synergistic effect on the degradation techniques.
Ultrasonic activation contributes degradation through cavitation
leading to the splitting of H2O2 produced by both photocatalysis and
sonolysis. This results in the formation of oxidative species, such as
singlet oxygen (1O2) and superoxide (O2
-●) radicals in the presence of
oxygen. The increase in the amount of reactive radical species which
induce faster oxidation of the substrate and degradation of
intermediates and also the deaggregation of the photocatalyst are
responsible for the synergy observed under sonication. A
comparative study of photocatalysis and sonophotocatalysis using
TiO2, Hombikat UV 100 and ZnO was also carried out.
Abstract: The use of polypropylene mesh devices for Pelvic
Organ Prolapse (POP) spread rapidly during the last decade, yet our
knowledge of the mesh-tissue interaction is far from complete. We
aimed to perform a thorough pathological examination of explanted
POP meshes and describe findings that may explain mechanisms of
complications resulting in product excision. We report a spectrum of
important findings, including nerve ingrowth, mesh deformation,
involvement of detrusor muscle with neural ganglia, and
polypropylene degradation. Analysis of these findings may improve
and guide future treatment strategies.
Abstract: Recently, distributed generation technologies have received much attention for the potential energy savings and reliability assurances that might be achieved as a result of their widespread adoption. Fueling the attention have been the possibilities of international agreements to reduce greenhouse gas emissions, electricity sector restructuring, high power reliability requirements for certain activities, and concern about easing transmission and distribution capacity bottlenecks and congestion. So it is necessary that impact of these kinds of generators on distribution feeder reconfiguration would be investigated. This paper presents an approach for distribution reconfiguration considering Distributed Generators (DGs). The objective function is summation of electrical power losses A Tabu search optimization is used to solve the optimal operation problem. The approach is tested on a real distribution feeder.
Abstract: In this paper some results on strict stability heve beeb extended for fuzzy differential equations with impulse effect using Lyapunov functions and Razumikhin technique.
Abstract: The fast growing accessibility and capability of emerging technologies have fashioned enormous possibilities of designing, developing and implementing innovative teaching methods in the classroom. The global technological scenario has paved the way to new pedagogies in teaching-learning process focusing on technology based learning environment and its impact on student achievement. The present experimental study was conducted to determine the effectiveness of technology based learning environment on student achievement in English as a foreign language. The sample of the study was 90 students of 10th grade of a public school located in Islamabad. A pretest- posttest equivalent group design was used to compare the achievement of the two groups. A Pretest and A posttest containing 50 items each from English textbook were developed and administered. The collected data were statistically analyzed. The results showed that there was a significant difference between the mean scores of Experimental group and the Control group. The performance of Experimental group was better on posttest scores that indicted that teaching through technology based learning environment enhanced the achievement level of the students. On the basis of the results, it was recommended that teaching and learning through information and communication technologies may be adopted to enhance the language learning capability of the students.
Abstract: This research was aimed at determining the impact of conservation techniques including bench terrace, stone terrace, mulching, grass strip and intercropping on soil erosion at tobacco-based farming system at Progo Hulu subwatershed, Central Java, Indonesia. Research was conducted from September 2007 to September 2009, located at Progo Hulu subwatershed, Central Java, Indonesia. Research site divided into 27 land units, and experimental fields were grouped based on the soil type and slope, ie: 30%, 45% and 70%, with the following treatments: 1) ST0= stone terrace (control); 2) ST1= stone terrace + Setaria spacelata grass strip on a 5 cm height dike at terrace lips + tobacco stem mulch with dose of 50% (7 ton/ ha); 3) ST2= stone terrace + Setaria spacelata grass strip on a 5 cm height dike at terrace lips + tobacco stem mulch with dose of 100% (14 ton/ ha); 4) ST3= stone terrace + tobacco and red bean intercropping + tobacco stem mulch with dose of 50% (7 ton/ ha). 5) BT0= bench terrace (control); 6) BT1= bench terrace + Setaria spacelata grass strip at terrace lips + tobacco stem mulch with dose of 50% (7 ton/ ha); 7) BT2= bench terrace + Setaria spacelata grass strip at terrace lips + tobacco stem mulch with dose of 100% (14 ton/ ha); 8) BT3= bench terrace + tobacco and red bean intercropping + tobacco stem mulch with dose of 50% (7 ton/ ha). The results showed that the actual erosion rates of research site were higher than that of tolerance erosion with mean value 89.08 ton/ha/year and 33.40 ton/ha/year, respectively. These resulted in 69% of total research site (5,119.15 ha) highly degraded. Conservation technique of ST2 was the most effective in suppressing soil erosion, by 42.87%, following with BT2 as much 30.63%. Others suppressed erosion only less than 21%.
Abstract: The purpose of this study is to introduce a new
interface program to calculate a dose distribution with Monte Carlo method in complex heterogeneous systems such as organs or tissues
in proton therapy. This interface program was developed under
MATLAB software and includes a friendly graphical user interface
with several tools such as image properties adjustment or results display. Quadtree decomposition technique was used as an image
segmentation algorithm to create optimum geometries from Computed Tomography (CT) images for dose calculations of proton
beam. The result of the mentioned technique is a number of nonoverlapped
squares with different sizes in every image. By this way
the resolution of image segmentation is high enough in and near
heterogeneous areas to preserve the precision of dose calculations
and is low enough in homogeneous areas to reduce the number of
cells directly. Furthermore a cell reduction algorithm can be used to combine neighboring cells with the same material. The validation of this method has been done in two ways; first, in comparison with experimental data obtained with 80 MeV proton beam in Cyclotron
and Radioisotope Center (CYRIC) in Tohoku University and second, in comparison with data based on polybinary tissue calibration method, performed in CYRIC. These results are presented in this paper. This program can read the output file of Monte Carlo code while region of interest is selected manually, and give a plot of dose distribution of proton beam superimposed onto the CT images.
Abstract: This paper presents a novel CMOS four-transistor
SRAM cell for very high density and low power embedded SRAM
applications as well as for stand-alone SRAM applications. This cell
retains its data with leakage current and positive feedback without
refresh cycle. The new cell size is 20% smaller than a conventional
six-transistor cell using same design rules. Also proposed cell uses
two word-lines and one pair bit-line. Read operation perform from
one side of cell, and write operation perform from another side of
cell, and swing voltage reduced on word-lines thus dynamic power
during read/write operation reduced. The fabrication process is fully
compatible with high-performance CMOS logic technologies,
because there is no need to integrate a poly-Si resistor or a TFT load.
HSPICE simulation in standard 0.25μm CMOS technology confirms
all results obtained from this paper.
Abstract: Attitude Determination (AD) of a spacecraft using the
phase measurements of the Global Navigation Satellite System
(GNSS) is an active area of research. Various attitude determination
algorithms have been developed in yester years for spacecrafts using
different sensors but the last two decades have witnessed a
phenomenal increase in research related with GPS receivers as a
stand-alone sensor for determining the attitude of satellite using the
phase measurements of the signals from GNSS. The GNSS-based
Attitude determination algorithms have been experimented in many
real missions. The problem of AD algorithms using GNSS phase
measurements has two important parts; the ambiguity resolution and
the determining of attitude. Ambiguity resolution is the widely
addressed topic in literature for implementing the AD algorithm
using GNSS phase measurements for achieving the accuracy of
millimeter level. This paper broadly overviews the different
techniques for resolving the integer ambiguities encountered in AD
using GNSS phase measurements.
Abstract: The fine structure of supercavitation in the wake of a
symmetrical cylinder is studied with high-speed video cameras. The
flow is observed in a cavitation tunnel at the speed of 8m/sec when the
sidewall and the wake are partially filled with the massive cavitation
bubbles. The present experiment observed that a two-dimensional
ripple wave with a wave length of 0.3mm is propagated in a
downstream direction, and then abruptly increases to a thicker
three-dimensional layer. IR-photography recorded that the wakes
originated from the horseshoe vortexes alongside the cylinder. The
wake was developed to inside the dead water zone, which absorbed the
bubbly wake propelled from the separated vortices at the center of the
cylinder. A remote sensing classification technique (maximum most
likelihood) determined that the surface porosity was 0.2, and the mean
speed in the mixed wake was 7m/sec. To confirm the existence of
two-dimensional wave motions in the interface, the experiments were
conducted at a very low frequency, and showed similar gravity waves
in both the upper and lower interfaces.
Abstract: A new deployment of the multiple criteria decision
making (MCDM) techniques: the Simple Additive Weighting
(SAW), and the Technique for Order Preference by Similarity to
Ideal Solution (TOPSIS) for portfolio allocation, is demonstrated in
this paper. Rather than exclusive reference to mean and variance as in
the traditional mean-variance method, the criteria used in this
demonstration are the first four moments of the portfolio distribution.
Each asset is evaluated based on its marginal impacts to portfolio
higher moments that are characterized by trapezoidal fuzzy numbers.
Then centroid-based defuzzification is applied to convert fuzzy
numbers to the crisp numbers by which SAW and TOPSIS can be
deployed. Experimental results suggest the similar efficiency of these
MCDM approaches to selecting dominant assets for an optimal
portfolio under higher moments. The proposed approaches allow
investors flexibly adjust their risk preferences regarding higher
moments via different schemes adapting to various (from
conservative to risky) kinds of investors. The other significant
advantage is that, compared to the mean-variance analysis, the
portfolio weights obtained by SAW and TOPSIS are consistently
well-diversified.
Abstract: An adaptive spatial Gaussian mixture model is proposed for clustering based color image segmentation. A new clustering objective function which incorporates the spatial information is introduced in the Bayesian framework. The weighting parameter for controlling the importance of spatial information is made adaptive to the image content to augment the smoothness towards piecewisehomogeneous region and diminish the edge-blurring effect and hence the name adaptive spatial finite mixture model. The proposed approach is compared with the spatially variant finite mixture model for pixel labeling. The experimental results with synthetic and Berkeley dataset demonstrate that the proposed method is effective in improving the segmentation and it can be employed in different practical image content understanding applications.
Abstract: The purpose of this paper is to detect human in images.
This paper proposes a method for extracting human body feature descriptors consisting of projected edge component series. The feature descriptor can express appearances and shapes of human with local
and global distribution of edges. Our method evaluated with a linear SVM classifier on Daimler-Chrysler pedestrian dataset, and test with
various sub-region size. The result shows that the accuracy level of
proposed method similar to Histogram of Oriented Gradients(HOG)
feature descriptor and feature extraction process is simple and faster than existing methods.
Abstract: This paper reports the three-phase (gas + liquid +
hydrate) equilibrium pressure versus temperature data for a (O3 + O2 +
CO2 + H2O) system for developing the hydrate-based technology to
preserve ozone, a chemically unstable substance, for various
industrial, medical and consumer uses. These data cover the
temperature range from 272 K to 277 K, corresponding to pressures
from 1.6 MPa to 3.1 MPa, for each of the three different (O3 +
O2)-to-CO2 or O2-to-CO2 molar ratios in the gas phase, which are
approximately 4 : 6, 5 : 5, respectively. The mole fraction of ozone in
the gas phase was ~0.03 , which are the densest ozone fraction to
artificially form O3 containing hydrate ever reported in the literature.
Based on these data, the formation of hydrate containing
high-concentration ozone, as high as 1 mass %, will be expected.
Abstract: The main aim of Supply Chain Management (SCM) is
to produce, distribute, logistics and deliver goods and equipment in
right location, right time, right amount to satisfy costumers, with
minimum time and cost waste. So implementing techniques that
reduce project time and cost, and improve productivity and
performance is very important. Emerging technologies such as the
Radio Frequency Identification (RFID) are now making it possible to
automate supply chains in a real time manner and making them more
efficient than the simple supply chain of the past for tracing and
monitoring goods and products and capturing data on movements of
goods and other events. This paper considers concepts, components
and RFID technology characteristics by concentration of warehouse
and inventories management. Additionally, utilization of RFID in the
role of improving information management in supply chain is
discussed. Finally, the facts of installation and this technology-s
results in direction with warehouse and inventory management and
business development will be presented.
Abstract: Explosive forming is one of the unconventional
techniques in which, most commonly, the water is used as the
pressure transmission medium. One of the newest methods in
explosive forming is gas detonation forming which uses a normal
shock wave derived of gas detonation, to form sheet metals. For this
purpose a detonation is developed from the reaction of H2+O2
mixture in a long cylindrical detonation tube. The detonation wave
goes through the detonation tube and acts as a blast load on the steel
blank and forms it. Experimental results are compared with a finite
element model; and the comparison of the experimental and
numerical results obtained from strain, thickness variation and
deformed geometry is carried out. Numerical and experimental
results showed approximately 75 – 90 % similarity in formability of
desired shape. Also optimum percent of gas mixture obtained when
we mix 68% H2 with 32% O2.
Abstract: With rapid technology scaling, the proportion of the
static power consumption catches up with dynamic power
consumption gradually. To decrease leakage consumption is
becoming more and more important in low-power design. This paper
presents a power-gating scheme for P-DTGAL (p-type dual
transmission gate adiabatic logic) circuits to reduce leakage power
dissipations under deep submicron process. The energy dissipations of
P-DTGAL circuits with power-gating scheme are investigated in
different processes, frequencies and active ratios. BSIM4 model is
adopted to reflect the characteristics of the leakage currents. HSPICE
simulations show that the leakage loss is greatly reduced by using the
P-DTGAL with power-gating techniques.
Abstract: Both the minimum energy consumption and
smoothness, which is quantified as a function of jerk, are generally
needed in many dynamic systems such as the automobile and the
pick-and-place robot manipulator that handles fragile equipments.
Nevertheless, many researchers come up with either solely
concerning on the minimum energy consumption or minimum jerk
trajectory. This research paper proposes a simple yet very interesting
when combining the minimum energy and jerk of indirect jerks
approaches in designing the time-dependent system yielding an
alternative optimal solution. Extremal solutions for the cost functions
of the minimum energy, the minimum jerk and combining them
together are found using the dynamic optimization methods together
with the numerical approximation. This is to allow us to simulate
and compare visually and statistically the time history of state inputs
employed by combining minimum energy and jerk designs. The
numerical solution of minimum direct jerk and energy problem are
exactly the same solution; however, the solutions from problem of
minimum energy yield the similar solution especially in term of
tendency.