Abstract: The springs located in urban areas are the outpouring
of surface water, which can serve as water supply, effluent receptors
and important local macro-drainage elements. With unplanned
occupation, non-compliance with environmental legislation and the
importance of these water bodies, it is vital to analyze the springs
within urban areas, considering the Brazilian forest code. This paper
submits an analysis and discussion methodology proposal of
environmental compliance functions of urban springs, by means of
G.I.S. - Geographic Information System analysis - and in situ
analysis. The case study included two springs which exhibit a history
of occupation along its length, with different degrees of impact. The
proposed method is effective and easy to apply, representing a
powerful tool for analyzing the environmental conditions of springs
in urban areas.
Abstract: In this study, a vibration analysis was carried out of
symmetric angle-ply laminated composite plates with and without
square hole when subjected to compressive loads, numerically. A
buckling analysis is also performed to determine the buckling load of
laminated plates. For each fibre orientation, the compression load is
taken equal to 50% of the corresponding buckling load. In the
analysis, finite element method (FEM) was applied to perform
parametric studies, the effects of degree of orthotropy and stacking
sequence upon the fundamental frequencies and buckling loads are
discussed. The results show that the presence of a constant
compressive load tends to reduce uniformly the natural frequencies
for materials which have a low degree of orthotropy. However, this
reduction becomes non-uniform for materials with a higher degree of
orthotropy.
Abstract: Embedding Sustainability in technological curricula has become a crucial factor for educating engineers with competences in sustainability. The Technical University of Catalonia UPC, in 2008, designed the Sustainable Technology Excellence Program STEP 2015 in order to assure a successful Sustainability Embedding. This Program takes advantage of the opportunity that the redesign of all Bachelor and Master Degrees in Spain by 2010 under the European Higher Education Area framework offered. The STEP program goals are: to design compulsory courses in each degree; to develop the conceptual base and identify reference models in sustainability for all specialties at UPC; to create an internal interdisciplinary network of faculty from all the schools; to initiate new transdisciplinary research activities in technology-sustainability-education; to spread the know/how attained; to achieve international scientific excellence in technology-sustainability-education and to graduate the first engineers/architects of the new EHEA bachelors with sustainability as a generic competence. Specifically, in this paper authors explain their experience in leading the STEP program, and two examples are presented: Industrial Robotics subject and the curriculum for the School of Architecture.
Abstract: In this paper, a neutral impulsive competition system with distributed delays is studied by using Mawhin-s coincidence degree theory and the mean value theorem of differential calculus. Sufficient conditions on the existence of positive periodic solution of the system are obtained.
Abstract: The objective of this research was to study the career
success and the satisfaction of female executives working for schools
in Bangkok, Thailand. This paper drew upon the survey data
collected from 68 female executives. The survey conducted in on
Bangkok schools. The statistics utilized in this paper included
percentage, mean, standard deviation as well as t-test. The findings
revealed that the majority of samples had more than 30 years of
experience, held a master degree, and had an average income of less
than 40,000 baht. The majority of respondents worked not more than
50 hours per week. In addition, the mean score revealed career
development was ranked as their number one career satisfaction and
having a job related to education was ranked as their number one job
satisfaction. Also, the mean score of all categories of satisfaction was
4.61 with standard deviation of 1.677 which indicated that female
executive level of satisfaction was high. In terms of the subjectivity
career success, the hypothesis testing’s result disclosed that female
executives with different married status had a difference in their job
satisfaction which was significant at the 0.05 confidence level.
Abstract: Haptics has been used extensively in many applications especially in human machine interaction and virtual reality systems. Haptic technology allows user to perceive virtual reality as in real world. However, commercially available haptic devices are expensive and may not be suitable for educational purpose. This paper describes the design and development of a low cost haptic knob, with only one degree of freedom, for use in rehabilitation or training hand pronation and supination. End-effectors can be changed to suit different applications or variation in hand sizes and hand orientation.
Abstract: This paper proves that the problem of finding connected
vertex cover in a 2-connected planar graph ( CVC-2 ) with maximum degree 4 is NP-complete. The motivation for proving this result is to
give a shorter and simpler proof of NP-Completeness of TRA-MLC (the Top Right Access point Minimum-Length Corridor) problem [1], by finding the reduction from CVC-2. TRA-MLC has many applications in laying optical fibre cables for data communication and electrical wiring in floor plans.The problem of finding connected vertex cover in any planar graph ( CVC ) with maximum degree 4 is NP-complete [2]. We first show that CVC-2 belongs to NP and then we find a polynomial reduction from CVC to CVC-2. Let a graph G0 and an integer K form an instance of CVC, where G0 is a planar graph and K is an upper bound on the size of the connected vertex cover in G0. We construct a 2-connected planar graph, say G, by identifying the blocks and cut vertices of G0, and then finding the planar representation of all the blocks of G0, leading to a plane graph G1. We replace the cut vertices with cycles in such a way that the resultant graph G is a 2-connected planar graph with maximum
degree 4. We consider L = K -2t+3 t i=1 di where t is the number of cut vertices in G1 and di is the number of blocks for which ith cut vertex is common. We prove that G will have a connected vertex
cover with size less than or equal to L if and only if G0 has a connected vertex cover of size less than or equal to K.
Abstract: Today, any organization - regardless of the specific activity - must be prepared to face continuous radical changes, innovation thus becoming a condition of survival in a globalized market. Few managers have a wider vision that includes innovation, to enable better performance of the critical activities, namely the degree of novelty that it must submit an innovation to be considered as such. Companies need not only radical changes in the products or their services, but also to their business strategies. Not all managers have an overall view on the real size of necessary innovation potential. Unfortunately there is still no common understanding (and correct) of the term of innovation among managers. Moreover, not all managers are aware of the need for innovation. In these conditions, increasing the processes adaptability of firms (through innovation) to meet the needs and performance requirements is difficult without a systematic framework. To overcome this disadvantage, the authors propose a framework for designing an innovation management system,, to cover all the important aspects of a business system, to reach the actual performance of an organization.
Abstract: The effect of muscle loss due to transfemoral
amputation, on energy expenditure of hip joint and individual
residual muscles was simulated. During swing phase of gait, with
each muscle as an ideal force generator, the lower extremity was
modeled as a two-degree of freedom linkage, for which hip and knee
were joints. According to results, muscle loss will not lead to higher
energy expenditure of hip joint, as long as other parameters of limb
remain unaffected. This finding maybe due to the role of biarticular
muscles in hip and knee joints motion. Moreover, if hip flexors are
removed from the residual limb, residual flexors, and if hip extensors
are removed, residual extensors will do more work. In line with the
common practice in transfemoral amputation, this result demonstrates
during transfemoral amputation, it is important to maintain the length
of residual limb as much as possible.
Abstract: Service trade is an important force of influencing economic development. A review on the related literatures is done firstly. Then through the construction of a Diamond Model, the main factors which influence the competitiveness of Chinese service trade are determined. With three competitiveness indexes served as the reference series respectively, the influencing factors served as the comparable series, three grey incidence models are then built up to conduct an empirical analysis on the main factors influencing the competitiveness of service trade after China entering WTO. The result indicates that urbanization level, open degree of service industry and foreign direct investment have larger impacts on Chinese service trade competitiveness, followed in turn by GDP in service industry and human capital, while commodity trade has the minimum impact. Further discussion provides train of thought for the upgrade of Chinese service trade competitiveness.
Abstract: Nonspecific protein adsorption generally occurs on
any solid surfaces and usually has adverse consequences. Adsorption
of proteins onto a solid surface is believed to be the initial and
controlling step in biofouling. Surfaces modified with end-tethered
poly(ethylene glycol) (PEG) have been shown to be protein-resistant
to some degree. In this study, the adsorption of β-casein and
lysozyme was performed on 6 different types of surfaces where PEG
was tethered onto stainless steel by polyethylene imine (PEI) through
either OH or NHS end groups. Protein adsorption was also performed
on the bare stainless steel surface as a control. The adsorption was
conducted at 23 °C and pH 7.2. In situ QCM-D was used to
determine PEG adsorption kinetics, plateau PEG chain densities,
protein adsorption kinetics and plateau protein adsorbed quantities.
PEG grafting density was the highest for a NHS coupled chain,
around 0.5 chains / nm2. Interestingly, lysozyme which has smaller
size than β-casein, appeared to adsorb much less mass than that of β-
casein. Overall, the surface with high PEG grafting density exhibited
a good protein rejection.
Abstract: This paper proposes an algorithm which automatically aligns and stitches the component medical images (fluoroscopic) with varying degrees of overlap into a single composite image. The alignment method is based on similarity measure between the component images. As applied here the technique is intensity based rather than feature based. It works well in domains where feature based methods have difficulty, yet more robust than traditional correlation. Component images are stitched together using the new triangular averaging based blending algorithm. The quality of the resultant image is tested for photometric inconsistencies and geometric misalignments. This method cannot correct rotational, scale and perspective artifacts.
Abstract: Owning to the high-speed feed rate and ultra spindle
speed have been used in modern machine tools, the tool-path
generation plays a key role in the successful application of a
High-Speed Machining (HSM) system. Because of its importance in
both high-speed machining and tool-path generation, approximating a
contour by NURBS format is a potential function in CAD/CAM/CNC
systems. It is much more convenient to represent an ellipse by
parametric form than to connect points laboriously determined in a
CNC system. A new approximating method based on optimum
processes and NURBS curves of any degree to the ellipses is presented
in this study. Such operations can be the foundation of tool-radius
compensation interpolator of NURBS curves in CNC system. All
operating processes for a CAD tool is presented and demonstrated by
practical models.
Abstract: The purpose of this research was to study the
influence of learning efficiency on local accountants’ job
performance effectiveness. This paper drew upon the survey data
collected from 335 local accountants survey conducted at Nakhon
Ratchasima province, Thailand. The statistics utilized in this paper
included percentage, mean, standard deviation, and regression
analysis. The findings revealed that the majority of samples were
between 31-40 years old, married, held an undergraduate degree, and
had an average income between 10,000-15,000 baht. The majority of
respondents had less than five years of accounting experience and
worked for local administrations. The overall learning efficiency
score was in the highest level while the local accountants’ job
performance effectiveness score was also in the high level. The
hypothesis testing’s result disclosed that learning efficiency factors
which were knowledge, Skill, and Attitude had an influence on local
accountants’ job the performance effectiveness.
Abstract: The increments of aromatic structures are widely used to monitor the degree of humification. Compost derived from mix manures mixed with agricultural wastes was studied. The compost collected at day 0, 7, 14, 21, 28, 35, 49, 77, 91, 105, and 119 was divided into 3 stages, initial stage at day 0, thermophilic stage during day 1-48, and mature stage during day 49-119. The change of highest absorptions at wavelength range between 210-235 nm during day 0- 49 implied that small molecules such as nitrates and carboxylic occurred faster than the aromatic molecules that were found at wavelength around 280 nm. The ratio of electron-transfer band at wavelength 253 nm by the benzonoid band at wavelength 230 nm (E253/E230) also gradually increased during the fermenting period indicating the presence of O-containing functional groups. This was in agreement with the shift change from aliphatic to aromatic structures as shown by the relationship with C/N and H/C ratios (r = - 0.631 and -0.717, p< 0.05) since both were decreasing. Although the amounts of humic acid (HA) were not different much during the humification process, the UV spectral deconvolution showed better qualitative characteristics to help in determining the compost quality. From this study, the compost should be used at day 49 and should not be kept longer than 3 months otherwise the quality of HA would decline regardless of the amounts of HA that might be rising. This implied that other processes, such as mineralization had an influence on the humification process changing HA-s structure and its qualities.
Abstract: The present work deals with optimization of cascade refrigeration system using eco friendly refrigerants pair R507A and R23. R507A is azeotropic mixture composed of HFC refrigerants R125/R143a (50%/50% by wt.). R23 is a single component HFC refrigerant used as replacement to CFC refrigerant R13 in low temperature applications. These refrigerants have zero ozone depletion potential and are non-flammable. Optimization of R507AR23 cascade refrigeration system performance parameters such as minimum work required, refrigeration effect, coefficient of performance and exergetic efficiency was carried out in terms of eight operating parameters- combinations using Genetic Algorithm tool. The eight operating parameters include (1) low side evaporator temperature (2) high side condenser temperature (3) temperature difference in the cascade heat exchanger (4) low side condenser temperature (5) low side degree of subcooling (6) high side degree of subcooling (7) low side degree of superheating (8) high side degree of superheating. Results show that for minimum work system should operate at high temperature in low side evaporator, low temperature in high side condenser, low temperature difference in cascade condenser, high temperature in low side condenser and low degree of subcooling and superheating in both side. For maximum refrigeration effect system should operate at high temperature in low side evaporator, high temperature in high side condenser, high temperature difference in cascade condenser, low temperature in low side condenser and higher degree of subcooling in LT and HT side. For maximum coefficient of performance and exergetic efficiency, system should operate at high temperature in low side evaporator, low temperature in high side condenser, low temperature difference in cascade condenser, high temperature in low side condenser and higher degree of subcooling and superheating in low side of the system.
Abstract: In the framework of adaptive parametric modelling of images, we propose in this paper a new technique based on the Chandrasekhar fast adaptive filter for texture characterization. An Auto-Regressive (AR) linear model of texture is obtained by scanning the image row by row and modelling this data with an adaptive Chandrasekhar linear filter. The characterization efficiency of the obtained model is compared with the model adapted with the Least Mean Square (LMS) 2-D adaptive algorithm and with the cooccurrence method features. The comparison criteria is based on the computation of a characterization degree using the ratio of "betweenclass" variances with respect to "within-class" variances of the estimated coefficients. Extensive experiments show that the coefficients estimated by the use of Chandrasekhar adaptive filter give better results in texture discrimination than those estimated by other algorithms, even in a noisy context.
Abstract: Microarrays have become the effective, broadly used tools in biological and medical research to address a wide range of problems, including classification of disease subtypes and tumors. Many statistical methods are available for analyzing and systematizing these complex data into meaningful information, and one of the main goals in analyzing gene expression data is the detection of samples or genes with similar expression patterns. In this paper, we express and compare the performance of several clustering methods based on data preprocessing including strategies of normalization or noise clearness. We also evaluate each of these clustering methods with validation measures for both simulated data and real gene expression data. Consequently, clustering methods which are common used in microarray data analysis are affected by normalization and degree of noise and clearness for datasets.
Abstract: As a part of evaluation system for R&D program, the
Korean government has applied feasibility analysis since 2008.
Various professionals put forth a great effort in order to catch up the
high degree of freedom of R&D programs, and make contributions to
evolving the feasibility analysis. We analyze diverse R&D programs
from various viewpoints, such as technology, policy, and Economics,
integrate the separate analysis, and finally arrive at a definite result;
whether a program is feasible or unfeasible. This paper describes the
concept and method of the feasibility analysis as a decision making
tool. The analysis unit and content of each criterion, which are key
elements in a comprehensive decision making structure, are examined
Abstract: In this paper, the existence of 2n positive periodic solutions for n species non-autonomous Lotka-Volterra cooperative systems with harvesting terms is established by using Mawhin-s continuation theorem of coincidence degree theory and matrix inequality. An example is given to illustrate the effectiveness of our results.