Abstract: This paper presents a grid synchronization technique based on adaptive notch filter for SPV (Solar Photovoltaic) system along with MPPT (Maximum Power Point Tracking) techniques. An efficient grid synchronization technique offers proficient detection of various components of grid signal like phase and frequency. It also acts as a barrier for harmonics and other disturbances in grid signal. A reference phase signal synchronized with the grid voltage is provided by the grid synchronization technique to standardize the system with grid codes and power quality standards. Hence, grid synchronization unit plays important role for grid connected SPV systems. As the output of the PV array is fluctuating in nature with the meteorological parameters like irradiance, temperature, wind etc. In order to maintain a constant DC voltage at VSC (Voltage Source Converter) input, MPPT control is required to track the maximum power point from PV array. In this work, a variable step size P & O (Perturb and Observe) MPPT technique with DC/DC boost converter has been used at first stage of the system. This algorithm divides the dPpv/dVpv curve of PV panel into three separate zones i.e. zone 0, zone 1 and zone 2. A fine value of tracking step size is used in zone 0 while zone 1 and zone 2 requires a large value of step size in order to obtain a high tracking speed. Further, adaptive notch filter based control technique is proposed for VSC in PV generation system. Adaptive notch filter (ANF) approach is used to synchronize the interfaced PV system with grid to maintain the amplitude, phase and frequency parameters as well as power quality improvement. This technique offers the compensation of harmonics current and reactive power with both linear and nonlinear loads. To maintain constant DC link voltage a PI controller is also implemented and presented in this paper. The complete system has been designed, developed and simulated using SimPower System and Simulink toolbox of MATLAB. The performance analysis of three phase grid connected solar photovoltaic system has been carried out on the basis of various parameters like PV output power, PV voltage, PV current, DC link voltage, PCC (Point of Common Coupling) voltage, grid voltage, grid current, voltage source converter current, power supplied by the voltage source converter etc. The results obtained from the proposed system are found satisfactory.
Abstract: In the past few years, high consumption of soft drinks
has attracted negative attention world-wide due to its possible
adverse effects, leading the health conscious people to find
alternative nutraceutical or herbal health drinks. In the present study,
a nutraceutical soft drink was developed utilizing some easily
available and well known traditional herbs having nutritional
potential. The key ingredients were selected as bael, amla, lemon
juice, ashwagandha and poppy seeds based on their household routine
use in the summer with proven refreshing, cooling and energetic
feeling since ages. After several trials made, the final composition of
nutraceutical summer soft drink was selected as most suitable
combination based on the taste, physicochemical, microbial and
organoleptic point of view. The physicochemical analysis of the
prepared drink found to contain optimum level of titratable acidity,
total soluble solids and pH which were in accordance of the
commercial recommendations. There were no bacterial colonies
found in the product therefore found within limits. During the nine
point’s hedonic scale sensory evaluation, the drink was strongly liked
for colour, taste, flavour and texture. The formulation was found to
contain flavonoids (80mg/100ml), phenolics (103mg/100ml), vitamin
C (250mg/100ml) and has antioxidant potential (75.52%) apart from
providing several other essential vitamins, minerals and healthy
components. The developed nutraceutical drink provides an
economical and feasible option for the consumers with very good
taste combined with potential health benefits. The present drink is
potentially capable to replace the synthetic soft drinks available in the
market.
Abstract: Due to the interference effects, the intrinsic
aerodynamic parameters obtained from the individual component
testing are always fundamentally different than those obtained for
complete model testing. Consideration and limitation for such testing
need to be taken into account in any design work related to the
component buildup method. In this paper, the scaled model of a
straight rectangular canard of a hybrid buoyant aircraft is tested at 50
m/s in IIUM-LSWT (Low Speed Wind Tunnel). Model and its
attachment with the balance are kept rigid to have results free from
the aeroelastic distortion. Based on the velocity profile of the test
section’s floor; the height of the model is kept equal to the
corresponding boundary layer displacement. Balance measurements
provide valuable but limited information of overall aerodynamic
behavior of the model. Zero lift coefficient is obtained at -2.2o and
the corresponding drag coefficient was found to be less than that at
zero angle of attack. As a part of the validation of low fidelity tool,
plot of lift coefficient plot was verified by the experimental data and
except the value of zero lift coefficients, the overall trend has under
predicted the lift coefficient. Based on this comparative study, a
correction factor of 1.36 is proposed for lift curve slope obtained
from the panel method.
Abstract: The purpose of this research was to investigate the
creep behaviour of the heterogeneous Timber-UHPFRC beams. New
developments have been done to further improve the structural
performance, such as strengthening of the timber (glulam) beam by
bonding composite material combine with an ultra-high performance
fibre reinforced concrete (UHPFRC) internally reinforced with or
without carbon fibre reinforced polymer (CFRP) bars. However, in
the design of wooden structures, in addition to the criteria of
strengthening and stiffness, deformability due to the creep of wood,
especially in horizontal elements, is also a design criterion. Glulam,
UHPFRC and CFRP may be an interesting composite mix to respond
to the issue of creep behaviour of composite structures made of
different materials with different rheological properties. In this paper,
we describe an experimental and analytical investigation of the creep
performance of the glulam-UHPFRC-CFRP beams assembled by
bonding. The experimental investigations creep behaviour was
conducted for different environments: in- and outside under constant
loading for approximately a year. The measured results are compared
with numerical ones obtained by an analytical model. This model was
developed to predict the creep response of the glulam-UHPFRCCFRP
beams based on the creep characteristics of the individual
components. The results show that heterogeneous glulam-UHPFRC
beams provide an improvement in both the strengthening and
stiffness, and can also effectively reduce the creep deflection of
wooden beams.
Abstract: The Adaptive Line Enhancer (ALE) is widely used for
enhancing narrowband signals corrupted by broadband noise. In this
paper, we propose novel ALE methods to improve the enhancing
capability. The proposed methods are motivated by the fact that the
output of the ALE is a fine estimate of the desired narrowband signal
with the broadband noise component suppressed. The proposed
methods preprocess the input signal using ALE filter to regenerate a
finer input signal. Thus the proposed ALE is driven by the input signal
with higher signal-to-noise ratio (SNR). The analysis and simulation
results are presented to demonstrate that the proposed ALE has better
performance than conventional ALE’s.
Abstract: This paper describes how to dimension the electric
components of a 48V hybrid system considering real customer use.
Furthermore, it provides information about savings in energy and
CO2 emissions by a customer-tailored 48V hybrid. Based on measured customer profiles, the electric units such as the
electric motor and the energy storage are dimensioned. Furthermore,
the CO2 reduction potential in real customer use is determined
compared to conventional vehicles. Finally, investigations are carried
out to specify the topology design and preliminary considerations in
order to hybridize a conventional vehicle with a 48V hybrid system.
The emission model results from an empiric approach also taking into
account the effects of engine dynamics on emissions. We analyzed
transient engine emissions during representative customer driving
profiles and created emission meta models. The investigation showed
a significant difference in emissions when simulating realistic
customer driving profiles using the created verified meta models
compared to static approaches which are commonly used for vehicle
simulation.
Abstract: In most existing buildings in hot climate, cooling
loads lead to high primary energy consumption and consequently
high CO2 emissions. These can be substantially decreased with
integrated renewable energy systems. Kuwait is characterized by its
dry hot long summer and short warm winter. Kuwait receives annual
total radiation more than 5280 MJ/m2 with approximately 3347 h of
sunshine. Solar energy systems consist of PV modules and parabolic
trough collectors are considered to satisfy electricity consumption,
domestic water heating, and cooling loads of an existing building.
This paper presents the results of an extensive program of energy
conservation and energy generation using integrated photovoltaic
(PV) modules and Parabolic Trough Collectors (PTC). The program
conducted on an existing institutional building intending to convert it
into a Net-Zero Energy Building (NZEB) or near net Zero Energy
Building (nNZEB). The program consists of two phases; the first
phase is concerned with energy auditing and energy conservation
measures at minimum cost and the second phase considers the
installation of photovoltaic modules and parabolic trough collectors.
The 2-storey building under consideration is the Applied Sciences
Department at the College of Technological Studies, Kuwait. Single
effect lithium bromide water absorption chillers are implemented to
provide air conditioning load to the building. A numerical model is
developed to evaluate the performance of parabolic trough collectors
in Kuwait climate. Transient simulation program (TRNSYS) is
adapted to simulate the performance of different solar system
components. In addition, a numerical model is developed to assess
the environmental impacts of building integrated renewable energy
systems. Results indicate that efficient energy conservation can play
an important role in converting the existing buildings into NZEBs as
it saves a significant portion of annual energy consumption of the
building. The first phase results in an energy conservation of about
28% of the building consumption. In the second phase, the integrated
PV completely covers the lighting and equipment loads of the
building. On the other hand, parabolic trough collectors of optimum
area of 765 m2 can satisfy a significant portion of the cooling load,
i.e about73% of the total building cooling load. The annual avoided
CO2 emission is evaluated at the optimum conditions to assess the
environmental impacts of renewable energy systems. The total annual
avoided CO2 emission is about 680 metric ton/year which confirms
the environmental impacts of these systems in Kuwait.
Abstract: This paper investigates the thermal issue of permanent
magnet synchronous generator which is frequently used in direct
drive gearless small-scale wind turbine applications. Permanent
Magnet Synchronous Generator (PMSG) is designed with 2.5 kW
continuous and 6 kW peak power. Then considering generator
geometry, mechanical design of wind turbine is performed. Thermal
analysis and optimization is carried out considering all wind turbine
components to reach realistic results. This issue is extremely
important in research and development (R&D) process for wind
turbine applications.
Abstract: The aims of study were investigation on chemical
composition essential oil and the effect of extract of Coronilla varia
on antimicrobial and cytotoxicity activity. The essential oils of
Coronilla varia is obtained by hydrodistillation and analyzed by
(GC/MS) for determining their chemical composition and
identification of their components. Antibacterial activity of plant
extract was determined by disc diffusion method and anticancer
activity measured by MTT assay. The major components in essential
oil were Caryophyllene Oxide (60.19%), Alphacadinol (4.13%) and
Homoadantaneca Robexylic Acid (3.31%). The extracts from
Coronilla varia had interesting activity against Proteus mirabilis in
the concentration of 700 μg/disc and did not show any activity
against Staphylococus aureus, Bacillus subtillis, Klebsiella
pneumonia and Entrobacter cloacae. The positive control,
Ampicillin, Chloramphenicol and Cenphalothin had shown zone of
inhibition resistant all bacteria. The ethanol extract of Corohilla varia
inhibited on MCF7 cell lines. IC50 0.6(mg/ml) was the optimum
concentration of extract from Coronilla varia inhibition of cell line
growth. The MCF7 cancer cell line and Proteus mirabilis were more
sensitive to Coronilla varia ethanol extract.
Abstract: As per the statistical data, the Doubly-fed Induction
Generator (DFIG) based wind turbine with variable speed and
variable pitch control is the most common wind turbine in the
growing wind market. This machine is usually used on the grid
connected wind energy conversion system to satisfy grid code
requirements such as grid stability, Fault Ride Through (FRT), power
quality improvement, grid synchronization and power control etc.
Though the requirements are not fulfilled directly by the machine, the
control strategy is used in both the stator as well as rotor side along
with power electronic converters to fulfil the requirements stated
above. To satisfy the grid code requirements of wind turbine, usually
grid side converter is playing a major role. So in order to improve the
operation capacity of wind turbine under critical situation, the
intensive study of both machine side converter control and grid side
converter control is necessary In this paper DFIG is modeled using
power components as variables and the performance of the DFIG
system is analysed under grid voltage fluctuations. The voltage
fluctuations are made by lowering and raising the voltage values in
the utility grid intentionally for the purpose of simulation keeping in
view of different grid disturbances.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear dynamics
analysis of the structures with assuming elastic-perfectly-plastic
behavior was performed using RAM PERFORM-3D software; the
horizontal component was taken into consideration with and without
the incorporation of the corresponding vertical component. Dynamic
responses obtained for the horizontal component acting alone were
compared with those obtained from the simultaneous application of
both seismic components. The results show that the effect of the
vertical component of ground motion may increase the axial load
significantly in the interior columns and, consequently, the stories.
The plastic mechanisms would be changed. The P-Delta effect is
expected to increase. The punching base plate shear of the columns
should be considered. Moreover, the vertical component increases the
input energy when the structures exhibit inelastic behavior and are
taller.
Abstract: These days, the industrial trend is moving away from heavy and bulky passive components to power converter systems that use more and more semiconductor elements. Also, it is difficult to connect the traditional converters to the high and medium voltage. For these reasons, a new family of multilevel inverters has appeared as a solution for working with higher voltage levels. Different modulation topologies like Sinusoidal Pulse Width Modulation (SPWM), Selective Harmonic Elimination Pulse Width Modulation (SHE-PWM) are available for multilevel inverters. In this work, different hybrid modulation techniques which are combination of fundamental frequency modulation and multilevel sinusoidal-modulation are compared. The main characteristic of these modulations are reduction of switching losses with good harmonic performance and balanced power loss dissipation among the device. The proposed hybrid modulation schemes are developed and simulated in Matlab/Simulink for cascaded H-bridge inverter. The results validate the applicability of the proposed schemes for cascaded multilevel inverter.
Abstract: The nickel-manganese (Ni-Mn) alloy coating prepared
from DC electrodeposition process in sulphamate bath was studied.
The effects of process parameters, such as current density and
electrolyte composition, on the cathodic current efficiency,
microstructure, internal stress and mechanical properties were
investigated. Because of its crucial effect on the application to the
electroforming of microelectronic components, the development of
low internal stress coating with high leveling power was emphasized.
It was found that both the coating’s manganese content and the
cathodic current efficiency increased with the raise in current density.
In addition, the internal stress of the deposited coating showed
compressive nature at low current densities while changed to tensile
one at higher current densities. Moreover, the metallographic
observation, X-ray diffraction measurement, and polarization curve
measurement were conducted. It was found that the Ni-Mn coating
consisted of nano-sized columnar grains and the maximum hardness of
the coating was associated with (111) preferred orientation in the
microstructure. The grain size was refined along with the increase in
the manganese content of the coating, which accordingly, raised its
hardness and resistance to annealing softening. In summary, the
Ni-Mn coating prepared at lower current density of 1-2 A/dm2 had low
internal stress, high leveling power, and better corrosion resistance.
Abstract: This study integrates a larger research empirical
project that examines second language (SL) learners’ profiles and
valid procedures to perform complete and diagnostic assessment in
schools. 102 learners of Portuguese as a SL aged 7 and 17 years
speakers of distinct home languages were assessed in several
linguistic tasks. In this article, we focused on writing performance in
the specific task of narrative essay composition. The written outputs
were measured using the score in six components adapted from an
English SL assessment context (Alberta Education): linguistic
vocabulary, grammar, syntax, strategy, socio-linguistic, and
discourse. The writing processes and strategies in Portuguese
language used by different immigrant students were analysed to
determine features and diversity of deficits on authentic texts
performed by SL writers. Differentiated performance was based on
the diversity of the following variables: grades, previous schooling,
home language, instruction in first language, and exposure to
Portuguese as Second Language. Indo-Aryan languages speakers
showed low writing scores compared to their peers and the type of
language and respective cognitive mapping (such as Mandarin and
Arabic) was the predictor, not linguistic distance. Home language
instruction should also be prominently considered in further research
to understand specificities of cognitive academic profile in a
Romance languages learning context. Additionally, this study also
examined the teachers’ representations that will be here addressed to
understand educational implications of second language teaching in
psychological distress of different minorities in schools of specific
host countries.
Abstract: This paper deals with nonlinear vibration analysis
using finite element method for frame structures consisting of elastic
and viscoelastic damping layers supported by multiple nonlinear
concentrated springs with hysteresis damping. The frame is supported
by four nonlinear concentrated springs near the four corners. The
restoring forces of the springs have cubic non-linearity and linear
component of the nonlinear springs has complex quantity to represent
linear hysteresis damping. The damping layer of the frame structures
has complex modulus of elasticity. Further, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled differential equations using normal coordinate corresponding
to linear natural modes. Comparing shares of strain energy of the
elastic frame, the damping layer and the springs, we evaluate the
influences of the damping couplings on the linear and nonlinear impact
responses. We also investigate influences of damping changed by
stiffness of the elastic frame on the nonlinear coupling in the damped
impact responses.
Abstract: Barley (Hordeum vulgare L.), vetch (Vicia villosa),
and grass pea (Lathyrus sativus L.) monocultures as well as mixtures
of barley with each of the above legumes, in three seeding ratios (i.e.,
barley: legume 75:25, 50:50 and 25:75, based on seed numbers) were
used to investigated forage yield and competition indices. The results
showed that intercropping reduced the dry matter yield of the three
component plants, compared with their respective monocrops. The
greatest value of total dry matter yield was obtained from barley25-
grasspea75 (5.44 t ha-1) mixture, followed by grass pea sole crop (4.99
t ha-1). The total actual yield loss (AYL) values were positive and
greater than 0 in all mixtures, indicating an advantage from
intercropping over sole crops. Intercropped barley had a higher
relative crowding coefficient (K=1.64) than intercropped legumes
(K=1.20), indicating that barley was more competitive than legumes
in mixtures. Furthermore, grass pea was more competitive than vetch
in mixtures with barley. The highest land equivalent ratio (LER),
system productivity index (SPI) and monetary advantage index
(MAI) were obtained when barley was mixed at a rate of 25% with
75% seed rate of grass pea. It is concluded that intercropping of
barley with grass pea has a good potential to improve the
performance of forage with high land-use efficiency.
Abstract: Coal tar is a liquid by-product of coal pyrolysis
processes. This liquid oil mixture contains various kinds of useful
compounds such as benzoic aromatic compounds and phenolic
compounds. These compounds are widely used as raw material for
insecticides, dyes, medicines, perfumes, coloring matters, and many
others. The coal tar was collected by pyrolysis process of coal
obtained from PT Kaltim Prima Coal and Arutmin-Kalimantan. The
experiments typically occurred at the atmospheric pressure in a
laboratory furnace at temperatures ranging from 300 to 550oC with a
heating rate of 10oC/min and a holding time of 1 hour at the pyrolysis
temperature. The Gas Chromatography-Mass Spectroscopy (GC-MS)
was used to analyze the coal tar components. The obtained coal tar
has the viscosity of 3.12 cp, the density of 2.78 g/cm3, the calorific
value of 11,048.44 cal/g, and the molecular weight of 222.67. The
analysis result showed that the coal tar contained more than 78
chemical compounds such as benzene, cresol, phenol, xylene,
naphtalene, etc. The total phenolic compounds contained in coal tar
are 33.25% (PT KPC) and 17.58% (Arutmin-Kalimantan). The total
naphtalene compounds contained in coal tar is 14.15% (PT KPC) and
17.13% (Arutmin-Kalimantan).
Abstract: The spindle system is one of the most important
components of machine tool. The dynamic properties of the spindle
affect the machining productivity and quality of the work pieces.
Thus, it is important and necessary to determine its dynamic
characteristics of spindles in the design and development in order to
avoid forced resonance. The finite element method (FEM) has been
adopted in order to obtain the dynamic behavior of spindle system.
For this reason, obtaining the Campbell diagrams and determining the
critical speeds are very useful to evaluate the spindle system
dynamics. The unbalance response of the system to the center of
mass unbalance at the cutting tool is also calculated to investigate the
dynamic behavior. In this paper, we used an ANSYS Parametric
Design Language (APDL) program which based on finite element
method has been implemented to make the full dynamic analysis and
evaluation of the results. Results show that the calculated critical
speeds are far from the operating speed range of the spindle, thus, the
spindle would not experience resonance, and the maximum
unbalance response at operating speed is still with acceptable limit.
ANSYS Parametric Design Language (APDL) can be used by spindle
designer as tools in order to increase the product quality, reducing
cost, and time consuming in the design and development stages.
Abstract: In this study, a multi objective optimization for end
milling of Al 6061 alloy has been presented to provide better
surface quality and higher Material Removal Rate (MRR). The input
parameters considered for the analysis are spindle speed, depth of cut
and feed. The experiments were planned as per Taguchis design of
experiment, with L27 orthogonal array. The Grey Relational Analysis
(GRA) has been used for transforming multiple quality responses
into a single response and the weights of the each performance
characteristics are determined by employing the Principal Component
Analysis (PCA), so that their relative importance can be properly and
objectively described. The results reveal that Taguchi based G-PCA
can effectively acquire the optimal combination of cutting parameters.
Abstract: The use of titanium fluoride and iron fluoride
(TiF3/FeF3) catalysts in combination with polutetrafluoroethylene
(PTFE) in plain zinc- dialkyldithiophosphate (ZDDP) oil is important
for the study of engine tribocomponents and is increasingly a strategy
to improve the formation of tribofilm and provide low friction and
excellent wear protection in reduced phosphorus plain ZDDP oil. The
influence of surface roughness and the concentration of
TiF3/FeF3/PTFE were investigated using bearing steel samples
dipped in lubricant solution at 100°C for two different heating time
durations. This paper addresses the effects of water drop contact
angle using different surface; finishes after treating them with
different lubricant combination. The calculated water drop contact
angles were analyzed using Design of Experiment software (DOE)
and it was determined that a 0.05 μm Ra surface roughness would
provide an excellent TiF3/FeF3/PTFE coating for antiwear resistance
as reflected in the Scanning electron microscopy (SEM) images and
the tribological testing under extreme pressure conditions. Both
friction and wear performance depend greatly on the PTFE/and
catalysts in plain ZDDP oil with 0.05 % phosphorous and on the
surface finish of bearing steel. The friction and wear reducing effects,
which was observed in the tribological tests, indicated a better micro
lubrication effect of the 0.05 μm Ra surface roughness treated at
100°C for 24 hours when compared to the 0.1 μm Ra surface
roughness with the same treatment.