Abstract: This study presents a systematic analysis of the
dynamic behaviors of a gear-bearing system with porous squeeze film
damper (PSFD) under nonlinear suspension, nonlinear oil-film force
and nonlinear gear meshing force effect. It can be found that the
system exhibits very rich forms of sub-harmonic and even the chaotic
vibrations. The bifurcation diagrams also reveal that greater values of
permeability may not only improve non-periodic motions effectively,
but also suppress dynamic amplitudes of the system. Therefore, porous
effect plays an important role to improve dynamic stability of
gear-bearing systems or other mechanical systems. The results
presented in this study provide some useful insights into the design
and development of a gear-bearing system for rotating machinery that
operates in highly rotational speed and highly nonlinear regimes.
Abstract: Resins are used in nuclear power plants for water
ultrapurification. Two approaches are considered in this work:
column experiments and simulations. A software called OPTIPUR
was developed, tested and used. The approach simulates the onedimensional
reactive transport in porous medium with convectivedispersive
transport between particles and diffusive transport within
the boundary layer around the particles. The transfer limitation in the
boundary layer is characterized by the mass transfer coefficient
(MTC). The influences on MTC were measured experimentally. The
variation of the inlet concentration does not influence the MTC; on
the contrary of the Darcy velocity which influences. This is consistent
with results obtained using the correlation of Dwivedi&Upadhyay.
With the MTC, knowing the number of exchange site and the relative
affinity, OPTIPUR can simulate the column outlet concentration
versus time. Then, the duration of use of resins can be predicted in
conditions of a binary exchange.
Abstract: In this paper, an estimation accuracy of multiple moving
talker tracking using a microphone array is improved. The tracking
can be achieved by the adaptive method in which two algorithms are integrated, namely, the PAST (Projection Approximation Subspace
Tracking) algorithm and the IPLS (Interior Point Least Square) algorithm. When either talker begins to speak again after a silent
period, an appropriate feasible region for an evaluation function of
the IPLS algorithm might not be set. Then, the tracking fails due to the incorrect updating. Therefore, if an increment of the number of
active talkers is detected, the feasible region must be reset. Then, a low cost realization is required for the high speed tracking and a high
accuracy realization is desired for the precise tracking. In this paper,
the directions roughly estimated using the delayed-sum-array method
are used for the resetting. Several results of experiments performed in
an actual room environment show the effectiveness of the proposed method.
Abstract: Historical monuments as architectural heritage are,
economically and culturally, considered one of the key aspects for
modern communities. Cultural heritage represents a country-s
national identity and pride and maintains and enriches that country-s
culture. Therefore, conservation of the monuments remained from
our ancestors requires everybody-s serious and unremitting effort.
Conservation, renewal, restoration, and technical study of cultural
and historical matters are issues which have a special status among
various forms of art and science in the present century and this is due
to two reasons: firstly, progress of humankind in this century has
created a factor called environmental pollution which not only has
caused new destructive processes of cultural/historical monuments
but also has accelerated the previous destructive processes by several
times, and secondly, the rapid advance of various sciences, especially
chemistry, has lead to the contribution of new methods and materials
to this significant issue.
Abstract: Software reliability prediction gives a great opportunity to measure the software failure rate at any point throughout system test. A software reliability prediction model provides with the technique for improving reliability. Software reliability is very important factor for estimating overall system reliability, which depends on the individual component reliabilities. It differs from hardware reliability in that it reflects the design perfection. Main reason of software reliability problems is high complexity of software. Various approaches can be used to improve the reliability of software. We focus on software reliability model in this article, assuming that there is a time redundancy, the value of which (the number of repeated transmission of basic blocks) can be an optimization parameter. We consider given mathematical model in the assumption that in the system may occur not only irreversible failures, but also a failure that can be taken as self-repairing failures that significantly affect the reliability and accuracy of information transfer. Main task of the given paper is to find a time distribution function (DF) of instructions sequence transmission, which consists of random number of basic blocks. We consider the system software unreliable; the time between adjacent failures has exponential distribution.
Abstract: It was analyzed of fatty acid composition of 16 strains
of microalgae lipid fractions isolated from different basins of
Kazakhstan and characterized by stable active growth in the
laboratory. Three species of green microalgae (Oocystis
rhomboideus, Chlorococcum infusionum, Dictyochlorella globosa)
and three species of diatoms (Synedra sp., Nitzshia sp., Pleurosigma
attenuatum) are characterized by a high content of lipids and are
promising for further study as a source of polyunsaturated fatty acids.
Abstract: Existing literature ondesign reasoning seems to give
either one sided accounts on expert design behaviour based on
internal processing. In the same way ecological theoriesseem to
focus one sidedly on external elementsthat result in a lack of unifying
design cognition theory. Although current extended design cognition
studies acknowledge the intellectual interaction between internal and
external resources, there still seems to be insufficient understanding
of the complexities involved in such interactive processes. As
such,this paper proposes a novelmulti-directional model for design
researchers tomap the complex and dynamic conduct controlling
behaviour in which both the computational and ecological
perspectives are integrated in a vertical manner. A clear distinction
between identified intentional and emerging physical drivers, and
relationships between them during the early phases of experts- design
process, is demonstrated by presenting a case study in which the
model was employed.
Abstract: According to the statistics, the prevalence of congenital hearing loss in Taiwan is approximately six thousandths; furthermore, one thousandths of infants have severe hearing impairment. Hearing ability during infancy has significant impact in the development of children-s oral expressions, language maturity, cognitive performance, education ability and social behaviors in the future. Although most children born with hearing impairment have sensorineural hearing loss, almost every child more or less still retains some residual hearing. If provided with a hearing aid or cochlear implant (a bionic ear) timely in addition to hearing speech training, even severely hearing-impaired children can still learn to talk. On the other hand, those who failed to be diagnosed and thus unable to begin hearing and speech rehabilitations on a timely manner might lose an important opportunity to live a complete and healthy life. Eventually, the lack of hearing and speaking ability will affect the development of both mental and physical functions, intelligence, and social adaptability. Not only will this problem result in an irreparable regret to the hearing-impaired child for the life time, but also create a heavy burden for the family and society. Therefore, it is necessary to establish a set of computer-assisted predictive model that can accurately detect and help diagnose newborn hearing loss so that early interventions can be provided timely to eliminate waste of medical resources. This study uses information from the neonatal database of the case hospital as the subjects, adopting two different analysis methods of using support vector machine (SVM) for model predictions and using logistic regression to conduct factor screening prior to model predictions in SVM to examine the results. The results indicate that prediction accuracy is as high as 96.43% when the factors are screened and selected through logistic regression. Hence, the model constructed in this study will have real help in clinical diagnosis for the physicians and actually beneficial to the early interventions of newborn hearing impairment.
Abstract: It is known that the heart interacts with and adapts to
its venous and arterial loading conditions. Various experimental
studies and modeling approaches have been developed to investigate
the underlying mechanisms. This paper presents a model of the left
ventricle derived based on nonlinear stress-length myocardial
characteristics integrated over truncated ellipsoidal geometry, and
second-order dynamic mechanism for the excitation-contraction
coupling system. The results of the model presented here describe the
effects of the viscoelastic damping element of the electromechanical
coupling system on the hemodynamic response. Different heart rates
are considered to study the pacing effects on the performance of the
left-ventricle against constant preload and afterload conditions under
various damping conditions. The results indicate that the pacing
process of the left ventricle has to take into account, among other
things, the viscoelastic damping conditions of the myofilament
excitation-contraction process.
Abstract: In this paper, in order to investigate the effects of
photovoltaic system introduction to detached houses in Japan, two
kinds of works were done. Firstly, the hourly generation amount of a
4.2kW photovoltaic system were simulated in 46 cities to investigate
the potential of the system in different regions in Japan using a
simulation model of photovoltaic system. Secondly, based on the
simulated electricity generation amount, the energy saving, the
environmental and the economic effect of the photovoltaic system
were examined from hourly to annual timescales, based upon
calculations of typical electricity, heating, cooling and hot water
supply load profiles for Japanese dwellings. The above analysis was
carried out using a standard year-s hourly weather data for the
different city provided by the Expanded AMeDAS Weather Data
issued by AIJ (Architectural Institute of Japan).
Abstract: Fip-gts, an immunomodulatory protein purified from Ganoderma tsugae, has been reported to possess therapeutic effects in the treatment of cancer and autoimmune disease. For medicinal application, a recombinant Fip-gts was successfully expressed and purified in Sf21 insect cells by our previously work. It is important to evaluate the immunomodulatory activity of the rFip-gts. To assess the immunomodulatory potential of rFip-gts, the T lymphocytes of murine splenocytes were used in the present study. Results revealed that rFip-gts induced cellular aggregation formation. Additionally, the expression of IL-2 and IFN-r were up-regulated after the treatment of rFip-gts, and a corresponding increased production of IL-2 and IFN-r in a dose-dependent manner. The results showed that rFip-gts has an immunomodulatory activity in inducing Th1 lymphocytes from murine splenocytes released IL-2 and IFN-γ, thus suggest that rFip-gts may have therapeutic potential in vivo as an immune modulator.
Abstract: To investigate the possible correlation between peer aggression and peer victimization, 148 sixth-graders were asked to respond to the Reduced Aggression and Victimization Scales (RAVS). RAVS measures the frequency of reporting aggressive behaviors or of being victimized during the previous week prior to the survey. The scales are composed of six items each. Each point represents one instance of aggression or victimization. Specifically, the Pearson Product-Moment Correlation Coefficient (PMCC) was used to determine the correlations between the scores of the sixthgraders in the two scales, both in individual items and total scores. Positive correlations were established and correlations were significant at the 0.01 levels.
Abstract: Research on damage of gears and gear pairs using
vibration signals remains very attractive, because vibration signals
from a gear pair are complex in nature and not easy to interpret.
Predicting gear pair defects by analyzing changes in vibration signal
of gears pairs in operation is a very reliable method. Therefore, a
suitable vibration signal processing technique is necessary to extract
defect information generally obscured by the noise from dynamic
factors of other gear pairs.This article presents the value of cepstrum
analysis in vehicle gearbox fault diagnosis. Cepstrum represents the
overall power content of a whole family of harmonics and sidebands
when more than one family of sidebands is present at the same time.
The concept for the measurement and analysis involved in using the
technique are briefly outlined. Cepstrum analysis is used for detection
of an artificial pitting defect in a vehicle gearbox loaded with
different speeds and torques. The test stand is equipped with three
dynamometers; the input dynamometer serves asthe internal
combustion engine, the output dynamometers introduce the load on
the flanges of the output joint shafts. The pitting defect is
manufactured on the tooth side of a gear of the fifth speed on the
secondary shaft. Also, a method for fault diagnosis of gear faults is
presented based on order Cepstrum. The procedure is illustrated with
the experimental vibration data of the vehicle gearbox. The results
show the effectiveness of Cepstrum analysis in detection and
diagnosis of the gear condition.
Abstract: One important objective in Precision Agriculture is to minimize the volume of herbicides that are applied to the fields through the use of site-specific weed management systems. In order to reach this goal, two major factors need to be considered: 1) the similar spectral signature, shape and texture between weeds and crops; 2) the irregular distribution of the weeds within the crop's field. This paper outlines an automatic computer vision system for the detection and differential spraying of Avena sterilis, a noxious weed growing in cereal crops. The proposed system involves two processes: image segmentation and decision making. Image segmentation combines basic suitable image processing techniques in order to extract cells from the image as the low level units. Each cell is described by two area-based attributes measuring the relations among the crops and the weeds. From these attributes, a hybrid decision making approach determines if a cell must be or not sprayed. The hybrid approach uses the Support Vector Machines and the Fuzzy k-Means methods, combined through the fuzzy aggregation theory. This makes the main finding of this paper. The method performance is compared against other available strategies.
Abstract: In this paper, a novel multi join algorithm to join
multiple relations will be introduced. The novel algorithm is based
on a hashed-based join algorithm of two relations to produce a double index. This is done by scanning the two relations once. But
instead of moving the records into buckets, a double index will be built. This will eliminate the collision that can happen from a complete hash algorithm. The double index will be divided into join
buckets of similar categories from the two relations. The algorithm then joins buckets with similar keys to produce joined buckets. This
will lead at the end to a complete join index of the two relations. without actually joining the actual relations. The time complexity
required to build the join index of two categories is Om log m where m is the size of each category. Totaling time complexity to O n log m
for all buckets. The join index will be used to materialize the joined relation if required. Otherwise, it will be used along with other join
indices of other relations to build a lattice to be used in multi-join operations with minimal I/O requirements. The lattice of the join indices can be fitted into the main memory to reduce time complexity of the multi join algorithm.
Abstract: The study was designed to develop a measurement of
the positive emotion regulation questionnaire (PERQ) that assesses
positive emotion regulation strategies through self-report. The 14
items developed for the surveying instrument of the study were based
upon literatures regarding elements of positive regulation strategies.
319 elementary students (age ranging from 12 to14) were recruited
among three public elementary schools to survey on their use of
positive emotion regulation strategies. Of 319 subjects, 20 invalid
questionnaire s yielded a response rate of 92%. The data collected
wasanalyzed through methods such as item analysis, factor analysis,
and structural equation models. In reference to the results from item
analysis, the formal survey instrument was reduced to 11 items. A
principal axis factor analysis with varimax was performed on
responses, resulting in a 2-factor equation (savoring strategy and
neutralizing strategy), which accounted for 55.5% of the total
variance. Then, the two-factor structure of scale was also identified by
structural equation models. Finally, the reliability coefficients of the
two factors were Cronbach-s α .92 and .74. Gender difference was
only found in savoring strategy. In conclusion, the positive emotion
regulation strategies questionnaire offers a brief, internally consistent,
and valid self-report measure for understanding the emotional
regulation strategies of children that may be useful to researchers and
applied professionals.
Abstract: Distance education program is a dimension of contemporary and new education technologies. Concepts and applications in this field are the results of a series of educational demands and developments in various communication and education technologies. Distance education applications have some conceptual bases. These are creating new education opportunities, realizing work-education unity, getting democratic in education, lifelong education, tendency to individual matters, effective use of institutions, integration of technology and education, tendency to individual and social needs, taking three dimensional integration as the main principle (publishing, printed materials and face to face education), reaching maximum mass, individual and mass education integrity and education demand and financial matters balance. Economics, Business Administration and Open Education faculties, which have been giving education within Anadolu University since 1982 in Turkey, are carrying on education with nearly 1.000.000 students. The aim of this study is to determine organizational commitment levels of students who have been studying at Anadolu University Economics, Business Administration and Open Education faculties in the scope of affective, continuance and nominative commitment in Allen&Meyer model. In the study, organizational commitment of the Economics, Business Administration and Open Education faculty students, who are receiving education by means of distance education, to their faculties is dealt after introducing Anadolu University Distance Education system which gives higher education via distance education method in Turkey. In order to increase the success level of faculties it is required for students to have high level of organizational commitment to their faculties. A questionnaire has been applied by using “Organizational Commitment Scale", developed by Meyer&Allen to determine organizational commitments of Economics, Business Administration and Open Education students. Organizational commitment is dealt with as affective, continuance and nominative commitment. The questionnaire was applied face to face to randomly chosen 500 students living in Eskişehir and the data was downloaded to the computer by using SPSS program and the results were analyzed in terms of demographic features (gender, age, marital status, years of study, work and income level) of students by using frequency test, ttest and ANOVA test. As a result of these analyses, when the comments of Open Education Faculty students on levels of affective, continuance and nominative commitment to their faculties were examined, it has been revealed that continuance commitment level has the highest rate. Among the female participants; continuance commitment is high in the age range of 30-40, for normative commitment it is 17-22. However no dominant age range was defined for affective commitment. Regarding the marital status; continuance commitment average is higher among married participants; but nominative affective commitment average is higher among single participants. As to the years of study, affective and continuance commitment is higher among senior students while normative commitment is higher among junior students. Moreover; in terms of continuance, affective and normative commitment, those who do not work and have low income have higher level of all there commitment types than those who work and have relatively high income.
Abstract: School brawls have taken casualties to the life of
students in Jakarta. In the last time, school brawl studies investigate
the cause with groups approach such as cognitive dissonance that
provocation and resentment among student in the schools. This
research focus on individual factors as the cause of school brawls,
where the characteristics of children with ADHD, lack of self-control
regulation, and level of depression. The results show that in fact the
lower influence of individual factor to be come conduct disorder. The
meaning students have good self-regulation control, insignificant
characteristics of children with ADHD, and moderate of depression
level. Concluded group factor more significant than individual factor
to caused school brawl.
Abstract: This paper presents the simulation of fragmentation
warhead using a hydrocode, Autodyn. The goal of this research is to
determine the lethal range of such a warhead. This study investigates
the lethal range of warheads with and without steel balls as
preformed fragments. The results from the FE simulation, i.e. initial
velocities and ejected spray angles of fragments, are further processed
using an analytical approach so as to determine a fragment hit density
and probability of kill of a modelled warhead. In order to simulate a
plenty of preformed fragments inside a warhead, the model requires
expensive computation resources. Therefore, this study attempts to
model the problem in an alternative approach by considering an
equivalent mass of preformed fragments to the mass of warhead
casing. This approach yields approximately 7% and 20% difference
of fragment velocities from the analytical results for one and two
layers of preformed fragments, respectively. The lethal ranges of the
simulated warheads are 42.6 m and 56.5 m for warheads with one and
two layers of preformed fragments, respectively, compared to 13.85
m for a warhead without preformed fragment. These lethal ranges are
based on the requirement of fragment hit density. The lethal ranges
which are based on the probability of kill are 27.5 m, 61 m and 70 m
for warheads with no preformed fragment, one and two layers of
preformed fragments, respectively.
Abstract: This paper presents a new feature based dense stereo
matching algorithm to obtain the dense disparity map via dynamic
programming. After extraction of some proper features, we use some
matching constraints such as epipolar line, disparity limit, ordering
and limit of directional derivative of disparity as well. Also, a coarseto-
fine multiresolution strategy is used to decrease the search space
and therefore increase the accuracy and processing speed. The
proposed method links the detected feature points into the chains and
compares some of the feature points from different chains, to
increase the matching speed. We also employ color stereo matching
to increase the accuracy of the algorithm. Then after feature
matching, we use the dynamic programming to obtain the dense
disparity map. It differs from the classical DP methods in the stereo
vision, since it employs sparse disparity map obtained from the
feature based matching stage. The DP is also performed further on a
scan line, between any matched two feature points on that scan line.
Thus our algorithm is truly an optimization method. Our algorithm
offers a good trade off in terms of accuracy and computational
efficiency. Regarding the results of our experiments, the proposed
algorithm increases the accuracy from 20 to 70%, and reduces the
running time of the algorithm almost 70%.