Abstract: Myoelectric control system is the fundamental
component of modern prostheses, which uses the myoelectric signals
from an individual’s muscles to control the prosthesis movements.
The surface electromyogram signal (sEMG) being noninvasive has
been used as an input to prostheses controllers for many years.
Recent technological advances has led to the development of
implantable myoelectric sensors which enable the internal
myoelectric signal (MES) to be used as input to these prostheses
controllers. The intramuscular measurement can provide focal
recordings from deep muscles of the forearm and independent signals
relatively free of crosstalk thus allowing for more independent
control sites. However, little work has been done to compare the two
inputs. In this paper we have compared the classification accuracy of
six pattern recognition based myoelectric controllers which use
surface myoelectric signals recorded using untargeted (symmetric)
surface electrode arrays to the same controllers with multichannel
intramuscular myolectric signals from targeted intramuscular
electrodes as inputs. There was no significant enhancement in the
classification accuracy as a result of using the intramuscular EMG
measurement technique when compared to the results acquired using
the surface EMG measurement technique. Impressive classification
accuracy (99%) could be achieved by optimally selecting only five
channels of surface EMG.
Abstract: The present study aims to explore the effect of
computerization on marketing performance in Snowa Company. In
other words, this study intends to respond to this question that
whether or not, is there any relationship between utilization of
computerization in marketing activities and marketing performance?
The statistical population included 60 marketing managers of Snowa
Company. In order to test the research hypotheses, Pearson
correlation coefficient was employed. The reliability was equal to
96.8%. In this study, computerization was the independent variable
and marketing performance was the dependent variable with
characteristics of market share, improving the competitive position,
and sales volume. The results of testing the hypotheses revealed that
there is a significant relationship between utilization of
computerization and market share, sales volume and improving the
competitive position.
Abstract: The purpose of the research described in this work is
to answer how to measure the rheologic (viscoelastic) properties
tendo–deformational characteristics of soft tissue. The method would
also resemble muscle palpation examination as it is known in clinical
practice. For this purpose, an instrument with the working name
“myotonometer” has been used. At present, there is lack of objective methods for assessing the
muscle tone by viscous and elastic properties of soft tissue. That is
why we decided to focus on creating or finding quantitative and
qualitative methodology capable to specify muscle tone.
Abstract: The rheological response of blends obtained from
quaternized polysulfone and polyvinyl alcohol in N-methyl-2-
pyrrolidone as against structural peculiarity of polymers from the
blend, composition of polymer mixtures, as well as the types of
interactions were investigated. Results show that the variation of
polyvinyl alcohol composition in the studied system determines
changes of the rheological properties, suggesting that the PVA acts as
a plasticizer. Consequently, rheological behavior of complex system,
described by the nonlinear flow curve, indicates the impact of
polyvinil alcohol content to polysulfone solution, in order to facilitate
the subsequently preparation of bioactive membranes.
Abstract: In the present study, a numerical approach to describe the pyrolysis of a single solid particle of wood is used to study the influence of various conditions such as particle size, heat transfer coefficient, reactor temperature and heating rate. The influence of these parameters in the change of the duration of the pyrolysis cycle was studied. Mathematical modeling was employed to simulate the heat, mass transfer, and kinetic processes inside the reactor. The evolutions of the mass loss as well as the evolution of temperature inside the thick piece are investigated numerically. The elaborated model was also employed to study the effect of the reactor temperature and the rate of heating on the change of the temperature and the local loss of the mass inside the piece of wood. The obtained results are in good agreement with the experimental data available in the literature.
Abstract: Creativity is marked by the ability or power, to
produce through imaginative skill and create something anew. The
University is one of the great places to improve the talent in
imaginative skill. The purpose of this study was to identify a
creativity of the student in presentation product development. Two
hundred seventeen Technical and Vocational Education (TVE)
students in Universiti Tun Hussein Onn had chosen as a respondent.
This study is to survey the level of creativity which is focused on
knowledge, skills, presentation style, and character of creative
personnel. The level of creativity was measured based on the scale at
low, medium and high followed by mean score level. The data
collected by questionnaire, then analyzed using SPSS version
20.0.The result of the study indicated that the students showed a
higher of creativity (mean score in Knowledge = 4.12 and Skills=
4.02). In conjunction with the findings, implications and
recommendations were suggested forward like to ensconce the
research and improve with a more creativity concept in presentation
product of development for learning and teaching process.
Abstract: With the increasing number of people reviewing
products online in recent years, opinion sharing websites has become
the most important source of customers’ opinions. Unfortunately,
spammers generate and post fake reviews in order to promote or
demote brands and mislead potential customers. These are notably
destructive not only for potential customers, but also for business
holders and manufacturers. However, research in this area is not
adequate, and many critical problems related to spam detection have
not been solved to date. To provide green researchers in the domain
with a great aid, in this paper, we have attempted to create a highquality
framework to make a clear vision on review spam-detection
methods. In addition, this report contains a comprehensive collection
of detection metrics used in proposed spam-detection approaches.
These metrics are extremely applicable for developing novel
detection methods.
Abstract: The beginning of 21st century has witnessed new
advancements in the design and use of new materials for biosensing
applications, from nano to macro, protein to tissue. Traditional
analytical methods lack a complete toolset to describe the
complexities introduced by living systems, pathological relations,
discrete hierarchical materials, cross-phase interactions, and
structure-property dependencies. Materiomics – via systematic
molecular dynamics (MD) simulation – can provide structureprocess-
property relations by using a materials science approach
linking mechanisms across scales and enables oriented biosensor
design. With this approach, DNA biosensors can be utilized to detect
disease biomarkers present in individuals’ breath such as acetone for
diabetes. Our wireless sensor array based on single-stranded DNA
(ssDNA)-decorated single-walled carbon nanotubes (SWNT) has
successfully detected trace amount of various chemicals in vapor
differentiated by pattern recognition. Here, we present how MD
simulation can revolutionize the way of design and screening of DNA
aptamers for targeting biomarkers related to oral diseases and oral
health monitoring. It demonstrates great potential to be utilized to
build a library of DNDA sequences for reliable detection of several
biomarkers of one specific disease, and as well provides a new
methodology of creating, designing, and applying of biosensors.
Abstract: An Energetic and exergetic analysis is conducted on a
Steam Turbine Power Plant of an existing Phosphoric Acid Factory.
The heat recovery systems used in different parts of the plant are also
considered in the analysis. Mass, thermal and exergy balances are
established on the main compounds of the factory. A numerical code
is established using EES software to perform the calculations
required for the thermal and exergy plant analysis. The effects of the
key operating parameters such as steam pressure and temperature,
mass flow rate as well as seawater temperature, on the cycle
performances are investigated. A maximum Exergy Loss Rate of about 72% is obtained for the
melters, followed by the condensers, heat exchangers and the pumps.
The heat exchangers used in the phosphoric acid unit present
exergetic efficiencies around 33% while 60% to 72% are obtained for
steam turbines and blower. For the explored ranges of HP steam
temperature and pressure, the exergy efficiencies of steam turbine
generators STGI and STGII increase of about 2.5% and 5.4%
respectively. In the same way optimum HP steam flow rate values,
leading to the maximum exergy efficiencies are defined.
Abstract: Teaching of mathematics to engineering students is an
open ended problem in education. The main goal of mathematics
learning for engineering students is the ability of applying a wide
range of mathematical techniques and skills in their engineering
classes and later in their professional work. Most of the
undergraduate engineering students and faculties feels that no efforts
and attempts are made to demonstrate the applicability of various
topics of mathematics that are taught thus making mathematics
unavoidable for some engineering faculty and their students. The lack
of understanding of concepts in engineering mathematics may hinder
the understanding of other concepts or even subjects. However, for
most undergraduate engineering students, mathematics is one of the
most difficult courses in their field of study. Most of the engineering students never understood mathematics or
they never liked it because it was too abstract for them and they could
never relate to it. A right balance of application and concept based
teaching can only fulfill the objectives of teaching mathematics to
engineering students. It will surely improve and enhance their
problem solving and creative thinking skills. In this paper, some practical (informal) ways of making
mathematics-teaching application based for the engineering students
is discussed. An attempt is made to understand the present state of
teaching mathematics in engineering colleges. The weaknesses and
strengths of the current teaching approach are elaborated. Some of
the causes of unpopularity of mathematics subject are analyzed and a
few pragmatic suggestions have been made. Faculty in mathematics
courses should spend more time discussing the applications as well as
the conceptual underpinnings rather than focus solely on strategies
and techniques to solve problems. They should also introduce more
‘word’ problems as these problems are commonly encountered in
engineering courses. Overspecialization in engineering education
should not occur at the expense of (or by diluting) mathematics and
basic sciences. The role of engineering education is to provide the
fundamental (basic) knowledge and to teach the students simple
methodology of self-learning and self-development. All these issues
would be better addressed if mathematics and engineering faculty
join hands together to plan and design the learning experiences for
the students who take their classes. When faculties stop competing
against each other and start competing against the situation, they will
perform better. Without creating any administrative hassles these
suggestions can be used by any young inexperienced faculty of
mathematics to inspire engineering students to learn engineering
mathematics effectively.
Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: Visibility problems are central to many computational geometry applications. One of the typical visibility problems is computing the view from a given point. In this paper, a linear time procedure is proposed to compute the visibility subsets from a corner of a rectangular prism in an orthogonal polyhedron. The proposed algorithm could be useful to solve classic 3D problems.
Abstract: In language learning, second language learners as well
as Native speakers commit errors in their attempt to achieve
competence in the target language. The realm of collocation has to do
with meaning relation between lexical items. In all human language,
there is a kind of ‘natural order’ in which words are arranged or relate
to one another in sentences so much so that when a word occurs in a
given context, the related or naturally co-occurring word will
automatically come to the mind. It becomes an error, therefore, if
students inappropriately pair or arrange such ‘naturally’ co–occurring
lexical items in a text. It has been observed that most of the second
language learners in this research group commit collocation errors. A
study of this kind is very significant as it gives insight into the kinds
of errors committed by learners. This will help the language teacher
to be able to identify the sources and causes of such errors as well as
correct them thereby guiding, helping and leading the learners
towards achieving some level of competence in the language. The
aim of the study is to understand the nature of these errors as
stumbling blocks to effective essay writing. The objective of the
study is to identify the errors, analyze their structural compositions so
as to determine whether there are similarities between students in this
regard and to find out whether there are patterns to these kinds of
errors which will enable the researcher to understand their sources
and causes. As a descriptive research, the researcher samples some
nine hundred essays collected from three hundred undergraduate
learners of English as a second language in the Federal College of
Education, Kano, North- West Nigeria, i.e. three essays per each
student. The essays which were given on three different lecture times
were of similar thematic preoccupations (i.e. same topics) and length
(i.e. same number of words). The essays were written during the
lecture hour at three different lecture occasions. The errors were
identified in a systematic manner whereby errors so identified were
recorded only once even if they occur severally in students’ essays.
The data was collated using percentages in which the identified
numbers of occurrences were converted accordingly in percentages.
The findings from the study indicate that there are similarities as well
as regular and repeated errors which provided a pattern. Based on the
pattern identified, the conclusion is that students’ collocation errors
are attributable to poor teaching and learning which resulted in wrong
generalization of rules.
Abstract: The crossover probability and mutation probability are the two important factors in genetic algorithm. The adaptive genetic algorithm can improve the convergence performance of genetic algorithm, in which the crossover probability and mutation probability are adaptively designed with the changes of fitness value. We apply adaptive genetic algorithm into a function optimization problem. The numerical experiment represents that adaptive genetic algorithm improves the convergence speed and avoids local convergence.
Abstract: The construction of most coastal infrastructure developments around the world are usually made considering wave height, current velocities and river discharges; however, little effort has been paid to surveying sediment transport during dredging or the modification to currents outside the ports or marinas during and after the construction. This study shows a complete survey during the construction of one of the largest ports of the Gulf of Mexico. An anchored Acoustic Doppler Current Velocity profiler (ADCP), a towed ADCP and a combination of model outputs were used at the Veracruz port construction in order to describe the hourly sediment transport and current modifications in and out of the new port. Owing to the stability of the system the new port was construction inside Vergara Bay, a low wave energy system with a tidal range of up to 0.40 m. The results show a two-current system pattern within the bay. The north side of the bay has an anticyclonic gyre, while the southern part of the bay shows a cyclonic gyre. Sediment transport trajectories were made every hour using the anchored ADCP, a numerical model and the weekly data obtained from the towed ADCP within the entire bay. The sediment transport trajectories were carefully tracked since the bay is surrounded by coral reef structures which are sensitive to sedimentation rate and water turbidity. The survey shows that during dredging and rock input used to build the wave breaker sediments were locally added (< 2500 m2) and local currents disperse it in less than 4 h. While the river input located in the middle of the bay and the sewer system plant may add more than 10 times this amount during a rainy day or during the tourist season. Finally, the coastal line obtained seasonally with a drone suggests that the southern part of the bay has not been modified by the construction of the new port located in the northern part of the bay, owing to the two subsystem division of the bay.
Abstract: Excessive vibration means increased wear, increased
repair efforts, bad product selection & quality and high energy
consumption. This may be sometimes experienced by cavitation or
suction/discharge recirculation which could occur only when net
positive suction head available NPSHA drops below the net positive
suction head required NPSHR. Cavitation can cause axial surging, if it
is excessive, will damage mechanical seals, bearings, possibly other
pump components frequently, and shorten the life of the impeller.
Efforts have been made to explain Suction Energy (SE), Specific
Speed (Ns), Suction Specific Speed (Nss), NPSHA, NPSHR & their
significance, possible reasons of cavitation /internal recirculation, its
diagnostics and remedial measures to arrest and prevent cavitation in
this paper. A case study is presented by the author highlighting that
the root cause of unwanted noise and vibration is due to cavitation,
caused by high specific speeds or inadequate net- positive suction
head available which results in damages to material surfaces of
impeller & suction bells and degradation of machine performance, its
capacity and efficiency too. Author strongly recommends revisiting
the technical specifications of CW pumps to provide sufficient NPSH
margin ratios >1.5, for future projects and Nss be limited to 8500 -
9000 for cavitation free operation.
Abstract: The most crucial aspect that is closely related to vocabulary and the one that needs to be emphasized and investigated more than it has been up until now, is the ability to combine words that co-occur frequently in the language. Pedagogically, collocation is one of the error-provoking aspects in foreign language learning. This is indicative of the dire need to provide L2 learners with tools to help them improve their collocational knowledge. This paper pinpoints the role that collocations play in the English language. Furthermore, it presents pedagogical implications for ESL/EFL learners.
Abstract: The paper presents an additive manufacturing process for the production of metal and composite parts. It is termed as composite metal foil manufacturing and is a combination of laminated object manufacturing and brazing techniques. The process has been described in detail and is being used to produce dissimilar aluminum to copper foil single lap joints. A three dimensional finite element model has been developed to study the thermo-mechanical characteristics of the dissimilar Al/Cu single lap joint. The effects of thermal stress and strain have been analyzed by carrying out transient thermal analysis on the heated plates used to join the two 0.1mm thin metal foils. Tensile test has been carried out on the foils before joining and after the single Al/Cu lap joints are made, they are subjected to tensile lap-shear test to analyze the effect of heat on the foils. The analyses are designed to assess the mechanical integrity of the foils after the brazing process and understand whether or not the heat treatment has an effect on the fracture modes of the produced specimens.
Abstract: Geological structure formed by volcanic activities shows polymorphic characteristics due to repeated cooling and hardening of lava. The Jeju region is showing polymorphic characteristics in which clinker layers are irregularly distributed along with vesicular basalt due to volcanic activities. Accordingly, resident damages and environmental disputes occur frequently in the Jeju region due to blasting. The purpose of this study is to develop a blast vibration equation considering the polymorphic characteristics of basaltic ground in Jeju. The blast vibration equation consists of a functional formula of the blasting vibration constant K that changes according to ground characteristics, and attenuation index n. The case study results in Jeju showed that if there are clinker layers, attenuation index n showed a distribution of -1.32~-1.81, whereas if there are no clinker layers, n was -2.79. Moreover, if there are no clinker layers, the frequency of blast vibration showed a high frequency band from 30Hz to 100Hz, while in rocks with clinker layers it showed a low frequency band from 10Hz to 20Hz.
Abstract: Electro-osmosis in clayey soils and sediments, for
purposes of clay consolidation, dewatering, or cleanup, and electro
injection in porous media is widespread recent decades. It is
experimentally found that the chemical properties of porous media
especially PH change the characteristics of media. Electro-osmotic
conductivity is a function of soil and grout material chemistry,
altering with time. Many numerical approaches exist to simulate the
of electro kinetic flow rate considering chemical changes. This paper
presents a simplified analytical solution for constant flow rate based
on varying electro osmotic conductivity and time dependent viscosity
for injection of colloidal silica.