Abstract: Stress Corrosion Crack (SCC) in pipeline is a type of
environmentally assisted cracking (EAC), since its discovery in 1965
as a possible cause of failure in pipeline, SCC has caused, on
average, one of two failures per year in the U.S, According to the
NACE SCC DA a pipe line segment is considered susceptible to SCC
if all of the following factors are met: The operating stress exceeds
60% of specified minimum yield strength (SMYS), the operating
temperature exceeds 38°C, the segment is less than 32 km
downstream from a compressor station, the age of the pipeline is
greater than 10 years and the coating type is other than Fusion
Bonded Epoxy(FBE). In this paper as a practical experience in
NISOC, Direct Assessment (DA) Method is used for identification
SCC defect in unpiggable pipeline located downstream of
compressor station.
Abstract: The global solved problem is the calculation of the
parameters of ceramic material from a set of destruction tests of
ceramic heads of total hip joint endoprosthesis. The standard way of
calculation of the material parameters consists in carrying out a set of
3 or 4 point bending tests of specimens cut out from parts of the
ceramic material to be analysed. In case of ceramic heads, it is not
possible to cut out specimens of required dimensions because the
heads are too small (if the cut out specimens were smaller than the
normalised ones, the material parameters derived from them would
exhibit higher strength values than those which the given ceramic
material really has). A special destruction device for heads
destruction was designed and the solved local problem is the
modification of this destructive device based on the analysis of
tensile stress in the head for two different values of the depth of the
conical hole in the head. The goal of device modification is a shift of
the location with extreme value of σ1max from the region of head’s
hole bottom to its opening. This modification will increase the
credibility of the obtained material properties of bioceramics, which
will be determined from a set of head destructions using the Weibull
weakest link theory.
Abstract: Nonstandard tests are necessary for analyses and
verification of new developed structural and technological solutions
with application of composite materials. One of the most critical
primary structural parts of a typical aerospace structure is T-joint.
This structural element is loaded mainly in shear, bending, peel and
tension. The paper is focused on the shear loading simulations. The
aim of the work is to obtain a representative uniform distribution of
shear loads along T-joint during the mechanical testing. A new
design of T-joint test procedure, numerical simulation and
optimization of representative boundary conditions are presented.
The different conditions and inaccuracies both in simulations and
experiments are discussed. The influence of different parameters on
stress and strain distributions is demonstrated on T-joint made of
CFRP (carbon fibre reinforced plastic). A special test rig designed by
VZLU (Aerospace Research and Test Establishment) for T-shear test
procedure is presented.
Abstract: In this paper, thick walled Cylindrical tanks or tubes
made of functionally graded material under internal pressure and
temperature gradient are studied. Material parameters have been
considered as power functions. They play important role in the
elastoplastic behavior of these materials. To clarify their role,
different materials with different parameters have been used under
temperature gradient. Finally, their effect and loading effect have
been determined in first yield point. Also, the important role of
temperature gradient was also shown. At the end the study has been
results obtained from changes in the elastic modulus and yield stress.
Also special attention is also given to the effects of this internal
pressure and temperature gradient in the creation of tensile and
compressive stresses.
Abstract: Polyethylene (PE), Polypropylene (PP), Polyethylene
(vinyl acetate) (EVA) and PE-ionomer nanocomposite samples were
prepared by mixing of the polymer with organofilized
montmorillonite fillers Cloisite 93A and Dellite 67G. The amount of
each modified montmorillonite (MMT) was fixed to 5% (w/w). The
twin-screw kneader was used for the compounding of polymer matrix
and chosen nanofillers. The level of MMT exfoliation was studied by
the transmission electron microscopy (TEM) observations. The
mechanical properties of prepared materials were evaluated by
dynamical mechanical analysis at 30°C and by the measurement of
tensile properties (stress and strain at break).
Abstract: The effect of Zn2+, Mg2+, and Ba2+ on Saccharomyces
pastorianus performance was evaluated in this study at independent
and three variable combinations. After 96 h of fermentation, high
wort fermentability (%F) = 29.53 was obtained in medium containing
900:4 ppm Mg2+ + Ba2+. Increased ethanol yield 7.35 %(v/v) and
7.13 %(v/v) were obtained in media containing 900:4 ppm Mg2+ +
Ba2+ and 12:900 ppm Zn2+ + Mg2+. Decrease %F = 22.54 and ethanol
yield 6.18 % (v/v) was obtained in medium containing 12:4 ppm Zn2+
+ Ba2+. In media containing the individual ions, increased %F =
27.94 and 26.03 were recorded for media containing 700 ppm Mg2+
and 2 ppm Ba2+ , with ethanol yield of 7.88% (v/v) and 7.62% (v/v)
respectively. Reduced %F and ethanol yield was observed for 10 ppm
Zn2+ and 4 ppm Ba2+ media. The impact of Ba2+ at 1 and 2 ppm was
significant.
Abstract: The effect of particle size on shear strength of
granular materials are investigated using direct shear tests. Small
direct shear test (60 mm by 60 mm by 24 mm deep) were conducted
for particles passing the sieves with opening size of 2.36 mm.
Meanwhile, particles passing the standard 20 mm sieves were tested
using large direct shear test (300 mm by 300 mm by 200 mm deep).
The large direct shear tests and the small direct shear tests carried out
using the same shearing rate of 0.09 mm/min and similar normal
stresses of 100, 200 and 300 kPa. The results show that the peak and
residual shear strength increases as particle size increases.
Abstract: This paper attempts to evaluate the effect of fire
damage on concrete by using nonlinear resonance vibration method,
one of the nonlinear nondestructive method. Concrete exhibits not
only nonlinear stress-strain relation but also hysteresis and discrete
memory effect which are contained in consolidated materials.
Hysteretic materials typically show the linear resonance frequency
shift. Also, the shift of resonance frequency is changed according to
the degree of micro damage. The degree of the shift can be obtained
through nonlinear resonance vibration method. Five exposure
scenarios were considered in order to make different internal micro
damage. Also, the effect of post-fire-curing on fire-damaged concrete
was taken into account to conform the change in internal damage.
Hysteretic nonlinearity parameter was obtained by amplitudedependent
resonance frequency shift after specific curing periods. In
addition, splitting tensile strength was measured on each sample to
characterize the variation of residual strength. Then, a correlation
between the hysteretic nonlinearity parameter and residual strength
was proposed from each test result.
Abstract: It is known that residual welding deformations give
negative effect to processability and operational quality of welded
structures, complicating their assembly and reducing strength.
Therefore, selection of optimal technology, ensuring minimum
welding deformations, is one of the main goals in developing a
technology for manufacturing of welded structures.
Through years, JSC SSTC has been developing a theory for
estimation of welding deformations and practical activities for
reducing and compensating such deformations during welding
process. During long time a methodology was used, based on analytic
dependence. This methodology allowed defining volumetric changes
of metal due to welding heating and subsequent cooling. However,
dependences for definition of structures deformations, arising as a
result of volumetric changes of metal in the weld area, allowed
performing calculations only for simple structures, such as units, flat
sections and sections with small curvature. In case of complex 3D
structures, estimations on the base of analytic dependences gave
significant errors.
To eliminate this shortage, it was suggested to use finite elements
method for resolving of deformation problem. Here, one shall first
calculate volumes of longitudinal and transversal shortenings of
welding joints using method of analytic dependences and further,
with obtained shortenings, calculate forces, which action is
equivalent to the action of active welding stresses. Further, a finiteelements
model of the structure is developed and equivalent forces
are added to this model. Having results of calculations, an optimal
sequence of assembly and welding is selected and special measures to
reduce and compensate welding deformations are developed and
taken.
Abstract: This article aims to study the effect of pressure on rocket motor case by Finite Element Method simulation to select optimal material in rocket motor manufacturing process. In this study, cylindrical tubes with outside diameter of 122 mm and thickness of 3 mm are used for simulation. Defined rocket motor case materials are AISI4130, AISI1026, AISI1045, AL2024 and AL7075. Internal pressure used for the simulation is 22 MPa.
The result from Finite Element Method shows that at a pressure of 22 MPa rocket motor case produced by AISI4130, AISI1045 and AL7075 can be used. A comparison of the result between AISI4130, AISI1045 and AL7075 shows that AISI4130 has minimum principal stress and confirm the results of Finite Element Method by the used of calculation method found that, the results from Finite Element Method has good reliability.
Abstract: It is necessary to manage the fatigue crack growth (FCG) once those cracks are detected during in-service inspections. In this paper, a simulation program (FCG-System) is developed utilizing the commercial software ABAQUS with its object-oriented programming interface to simulate the fatigue crack path and to compute the corresponding fatigue life. In order to apply FCG-System in large-scale marine structures, the substructure modeling technique is integrated in the system under the consideration of structural details and load shedding during crack growth. Based on the nodal forces and nodal displacements obtained from finite element analysis, a formula for shell elements to compute stress intensity factors is proposed in the view of virtual crack closure technique. The cracks initiating from the intersection of flange and the end of the web-stiffener are investigated for fatigue crack paths and growth lives under water pressure loading and axial force loading, separately. It is found that the FCG-System developed by authors could be an efficient tool to perform fatigue crack growth analysis on marine structures.
Abstract: Static VAR System (SVS) is a kind of FACTS device which is used in power system primarily for the purpose of voltage and reactive power control. In this paper presents a systematic approach for designing SVS supplementary controller, which is used to improve the damping of power system oscillation. The combined bus voltage and line current (CBVLC) supplementary controller has been developed and incorporated in the SVS control system located at the middle of the series compensated long transmission line. Damping of torsional stresses due to subsynchronous resonance resulting from series capacitive compensation using CBVLC is investigated in this paper. Simulation results are carried out with MATLAB/Simulink on the IEEE first benchmark model (FBM). The simulation results show that the oscillations are satisfactorily damped out by the SVS supplementary controller. Time domain simulation is performed on power system and the results demonstrate the effectiveness of the proposed controller.
Abstract: The process of thermoforming a carbon fiber reinforced thermoplastic (CFRTP) has increased its presence in the automotive industry for its wide applicability to the mass production car. A non-isothermal forming for CFRTP can shorten its cycle time to less than 1 minute. In this paper, the textile reinforcement FE model which the authors proposed in a previous work is extended to the CFRTP model for non-isothermal forming simulation. The effect of thermoplastic is given by adding shell elements which consider thermal effect to the textile reinforcement model. By applying Reuss model to the stress calculation of thermoplastic, the proposed model can accurately predict in-plane shear behavior, which is the key deformation mode during forming, in the range of the process temperature. Using the proposed model, thermoforming simulation was conducted and the results are in good agreement with the experimental results.
Abstract: The analysis and design of thin shell structures is a topic of interest in a variety of engineering applications. In structural mechanics problems the analyst seeks to determine the distribution of stresses throughout the structure to be designed. It is also necessary to calculate the displacements of certain points of the structure to ensure that specified allowable values are not exceeded. In this paper a comparative study between displacement and strain based finite elements applied to the analysis of some thin shell structures is presented. The results obtained from some examples show the efficiency and the performance of the strain based approach compared to the well known displacement formulation.
Abstract: The impact deformation and fracture behaviour of cobalt-based Haynes 188 superalloy are investigated by means of a split Hopkinson pressure bar. Impact tests are performed at strain rates ranging from 1×103 s-1 to 5×103 s-1 and temperatures between 25°C and 800°C. The experimental results indicate that the flow response and fracture characteristics of cobalt-based Haynes 188 superalloy are significantly dependent on the strain rate and temperature. The flow stress, work hardening rate and strain rate sensitivity all increase with increasing strain rate or decreasing temperature. It is shown that the impact response of the Haynes 188 specimens is adequately described by the Zerilli-Armstrong fcc model. The fracture analysis results indicate that the Haynes 188 specimens fail predominantly as the result of intensive localised shearing. Furthermore, it is shown that the flow localisation effect leads to the formation of adiabatic shear bands. The fracture surfaces of the deformed Haynes 188 specimens are characterised by dimple- and / or cleavage-like structure with knobby features. The knobby features are thought to be the result of a rise in the local temperature to a value greater than the melting point.
Abstract: The extracellular proteins secreted by bacteria may be increased in stressful surroundings, such as in the presence of antibiotics. It appears that many antibiotics, when used at low concentrations, have in common the ability to activate or repress gene transcription, which is distinct from their inhibitory effect. There have been comparatively few studies on the potential of antibiotics as a specific chemical signal that can trigger a variety of biological functions. Therefore, this study was carried out to determine the effect of Streptomycin Sulfate in regulating extracellular proteins secreted by Bacillus subtilis ATCC21332. Results of Microdilution assay showed that the Minimum Inhibition Concentration (MIC) of Streptomycin Sulfate on B. subtilis ATCC21332 was 2.5 mg/ml. The bacteria cells were then exposed to Streptomycin Sulfate at concentration of 0.01 MIC before being further incubated for 48h to 72 h. The extracellular proteins secreted were then isolated and analyzed by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). Proteins profile revealed that three additional bands with approximate sizes of 30 kDa, 22 kDa and 23 kDa were appeared for the treated bacteria with Streptomycin Sulfate. Thus, B. subtilis ATCC21332 in stressful condition with the presence of Streptomycin Sulfate at low concentration could induce the extracellular proteins secretion.
Abstract: Outrigger-braced wall systems are commonly used to provide high rise buildings with the required lateral stiffness for wind and earthquake resistance. The existence of outriggers adds to the stiffness and strength of walls as reported by several studies. The effects of different parameters on the elasto-plastic dynamic behavior of outrigger-braced wall systems to earthquakes are investigated in this study. Parameters investigated include outrigger stiffness, concrete strength, and reinforcement arrangement as the main design parameters in wall design. In addition to being significantly affect the wall behavior, such parameters may lead to the change of failure mode and the delay of crack propagation and consequently failure as the wall is excited by earthquakes. Bi-linear stress-strain relation for concrete with limited tensile strength and truss members with bi-linear stress-strain relation for reinforcement were used in the finite element analysis of the problem. The famous earthquake record, El-Centro, 1940 is used in the study. Emphasize was given to the lateral drift, normal stresses and crack pattern as behavior controlling determinants. Results indicated significant effect of the studied parameters such that stiffer outrigger, higher grade concrete and concentrating the reinforcement at wall edges enhance the behavior of the system. Concrete stresses and cracking behavior are too much enhanced while less drift improvements are observed.
Abstract: In this paper, an analytical study is made for the dynamic behavior of human brain tissue under transient loading. In this analytical model the Mooney-Rivlin constitutive law is coupled with visco-elastic constitutive equations to take into account both the nonlinear and time-dependent mechanical behavior of brain tissue. Five ordinary differential equations representing the relationships of five main parameters (radial stress, circumferential stress, radial strain, circumferential strain, and particle velocity) are obtained by using the characteristic method to transform five partial differential equations (two continuity equations, one motion equation, and two constitutive equations). Analytical expressions of the attenuation properties for spherical wave in brain tissue are analytically derived. Numerical results are obtained based on the five ordinary differential equations. The mechanical responses (particle velocity and stress) of brain are compared at different radii including 5, 6, 10, 15 and 25 mm under four different input conditions. The results illustrate that loading curves types of the particle velocity significantly influences the stress in brain tissue. The understanding of the influence by the input loading cures can be used to reduce the potentially injury to brain under head impact by designing protective structures to control the loading curves types.
Abstract: The aim of this work is to analyze a viscous flow
around the axisymmetric blunt body taken into account the mesh size
both in the free stream and into the boundary layer. The resolution of
the Navier-Stokes equations is realized by using the finite volume
method to determine the flow parameters and detached shock
position. The numerical technique uses the Flux Vector Splitting
method of Van Leer. Here, adequate time stepping parameter, CFL
coefficient and mesh size level are selected to ensure numerical
convergence. The effect of the mesh size is significant on the shear
stress and velocity profile. The best solution is obtained with using a
very fine grid. This study enabled us to confirm that the
determination of boundary layer thickness can be obtained only if the
size of the mesh is lower than a certain value limits given by our
calculations.
Abstract: This article presents a monitoring indicators system
that predicts whether a local government in Taiwan is heading for
fiscal distress and identifies a suitable fiscal policy that would allow
the local government to achieve fiscal balance in the long run. This
system is relevant to stockholders’ interest, simple for national audit
bodies to use, and provides an early warning of fiscal distress that
allows preventative action to be taken.