Abstract: Transmission shafts are affected by various forces, for
example, during acceleration or sudden breaks, bending during
transportation, vertical forces that lead to cuts. One of the main
failures in combines is breaking shaft which repairmen refer it.
Structural resistance of canal against torque is very important in the
beginning of the movement. For analyzing stress, a typical sample
from a type of combine was selected, called JD955 combine. Long
shaft in this combine was analyzed with finite element method by
Ansys13 generic package under static load. Conducted analysis
showed that there is a maximum stress in contact surfaces of
indentations and also in place of changing diameter. Safety factor
value is low in parts of the shaft and this increases the probability of
failure at these points. To improve the conditions with the least cost
and an approach of product improvement, using alternative alloy is
important.
Abstract: Steel tubular towers serving as support structures for large wind turbines are subjected to several hundred million stress cycles caused by the turbulent nature of the wind. This causes highcycle fatigue, which could govern the design of the tower. Maintaining the support structure after the wind turbines reach its typical 20-year design life has become a common practice; however, quantifying the changes in the reliability on the tower is not usual. In this paper the effect of fatigue damage in the wind turbine structure is studied whit the use of fracture mechanics, and a method to estimate the reliability over time of the structure is proposed. A representative wind turbine located in Oaxaca, Mexico is then studied. It is found that the system reliability is significantly affected by the accumulation of fatigue damage.
Abstract: The paper is focused on the identification of limiting
environmental factors of individual industrial floors on which newly
developed polymer protection and repair systems with the use of
secondary raw materials will be used. These mainly include floors
with extreme stresses and special requirements for materials used. In
relation to the environment of a particular industrial floor, it is
necessary to ensure, for example, chemical stability, resistance to
higher temperatures, resistance to higher mechanical stress, etc. for
developed materials, which is reflected in the demands for the
developed material systems. The paper describes individual
environments and, in relation to them, also requirements for
individual components of the developed materials and for the
developed materials as a whole.
Abstract: Reliability of long-term storage products is related to
the availability of the whole system, and the evaluation of storage life
is of great necessity. These products are usually highly reliable and
little failure information can be collected. In this paper, an analytical
method based on data from accelerated storage life test is proposed to
evaluate the reliability index of the long-term storage products. Firstly,
singularities are eliminated by data normalization and residual
analysis. Secondly, with the preprocessed data, the degradation path
model is built to obtain the pseudo life values. Then by life distribution
hypothesis, we can get the estimator of parameters in high stress levels
and verify failure mechanism consistency. Finally, the life distribution
under the normal stress level is extrapolated via the acceleration model
and evaluation of the actual average life is available. An application
example with the camera stabilization device is provided to illustrate
the methodology we proposed.
Abstract: This paper presents the design and fabrication of an
optical window for an optical modulator toward image sensing
applications. An optical window consists of micrometer-order SiO2
capillaries (porous solid) that can modulate transmission light
intensity by moving the liquid in and out of porous solid. A high
optical transmittance of the optical window can be achieved due to
refractive index matching when the liquid is penetrated into the
porous solid. Otherwise, its light transmittance is lower because of
light reflection and scattering by air holes and capillary walls. Silicon
capillaries fabricated by deep reactive ion etching (DRIE) process are
completely oxidized to form the SiO2 capillaries. Therefore, high
aspect ratio SiO2 capillaries can be achieved based on silicon
capillaries formed by DRIE technique. Large compressive stress of
the oxide causes bending of the capillary structure, which is reduced
by optimizing the design of device structure. The large stress of the
optical window can be released via thin supporting beams. A 7.2 mm
x 9.6 mm optical window area toward a fully integrated with the
image sensor format is successfully fabricated and its optical
transmittance is evaluated with and without inserting liquids (ethanol
and matching oil). The achieved modulation range is approximately
20% to 35% with and without liquid penetration in visible region
(wavelength range from 450 nm to 650 nm).
Abstract: In this paper, the effects of fiber types and elevated
temperatures on compressive strength, modulus of rapture and the
bond characteristics of fiber reinforced concretes (FRC) are
presented. By using the three different types of fibers (steel fiber-SF,
polypropylene-PPF and polyvinyl alcohol-PVA), FRC specimens
were produced and exposed to elevated temperatures up to 800 ºC for
1.5 hours. In addition, a plain concrete (without fiber) was produced
and used as a control. Test results obtained showed that the steel fiber
reinforced concrete (SFRC) had the highest compressive strength,
modulus of rapture and bond stress values at room temperatures, the
residual bond, flexural and compressive strengths of both FRC and
plain concrete dropped sharply after exposure to high temperatures.
The results also indicated that the reduction of bond, flexural and
compressive strengths with increasing the exposed temperature was
relatively less for SFRC than for plain, and FRC with PPF and PVA.
Abstract: This paper presents experimental investigation and
finite element analysis on buckling behavior of irregular section coldformed
steel columns under axially concentric loading. For the
experimental study, four different sections of columns were tested to
investigate effect of stiffening and width-to-thickness ratio on
buckling behavior. For each of the section, three lengths of 230, 950
and 1900 mm. were studied representing short, intermediate long and
long columns, respectively. Then, nonlinear finite element analyses
of the tested columns were performed. The comparisons in terms of
load-deformation response and buckling mode show good agreement
and hence the FEM models were validated. Parametric study of
stiffening element and thickness of 1.0, 1.15, 1.2, 1.5, 1.6 and 2.0
mm. was analyzed. The test results showed that stiffening effect pays
a large contribution to prevent distortional mode. The increase in wall
thickness enhanced buckling stress beyond the yielding strength in
short and intermediate columns, but not for the long columns.
Abstract: Verification of vented wooden façade system with
bonded joints is presented in this paper. The potential of bonded
joints is studied and described in more detail. The paper presents the results of an experimental and theoretical research about the effects of freeze cycling on the bonded joint. For the purpose of tests spruce
timber profiles were chosen for the load bearing substructure. Planks from wooden plastic composite and Siberian larch are representing facade cladding. Two types of industrial polyurethane adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent curing and conditioning of test samples. All test samples were subjected to 15 cycles that represents sudden temperature changes, i.e. immersion in a water bath at (293.15 ± 3) K for 6 hours and subsequent freezing to (253.15 ± 2) K for 18 hours. Furthermore, the retention of bond strength between substructure and cladding wastested and strength in shear was determined under tensile stress.Research data indicate that little, if any, damage to the bond results from freezingcycles. Additionally, the suitability of selected group of adhesives in combination with timber substructure was confirmed.
Abstract: Employer branding is considered as a useful tool for
addressing the global-local problem facing complex organisations
that have operations scattered across the globe and face challenges of
dealing with the local environment alongside. Despite being an
established field of study within the Western developed world, there
is little empirical evidence concerning the relevance of employer
branding to global companies that operate in the under-developed
economies. This paper fills this gap by gaining rich insight into the
implementation of employer branding programs in a foreign
multinational operating in Pakistan dealing with the global-local
problem. The study is qualitative in nature and employs semistructured
and focus group interviews with senior/middle managers
and local frontline employees to deeply examine the phenomenon in
case organisation. Findings suggest that authenticity is required in
employer brands to enable them to respond to the local needs thereby
leading to the resolution of the global-local problem. However, the
role of signaling theory is key to the development of authentic
employer brands as it stresses on the need to establish an efficient and
effective signaling environment where in signals travel in both
directions (from signal designers to receivers and backwards) and
facilitate firms with the global-local problem. The paper also
identifies future avenues of research for the employer branding field.
Abstract: This article presents modeling studies of NiAl alloy
under solid-particle erosion and liquid-drop erosion. In the
solid-particle erosion simulation, attention is paid to the oxide scale
thickness variation on the alloy in high-temperature erosion
environments. The erosion damage is assumed to be deformation wear
and cutting wear mechanisms, incorporating the influence of the oxide
scale on the eroded surface; thus the instantaneous oxide thickness is
the result of synergetic effect of erosion and oxidation. For liquid-drop
erosion, special interest is in investigating the effects of drop velocity
and drop size on the damage of the target surface. The models of
impact stress wave, mean depth of penetration, and maximum depth of
erosion rate (Max DER) are employed to develop various maps for
NiAl alloy, including target thickness vs. drop size (diameter), rate of
mean depth of penetration (MDRP) vs. drop impact velocity, and
damage threshold velocity (DTV) vs. drop size.
Abstract: In general, codes and regulations consider seismic
loads only for completed structures of the bridges while, evaluation
of incomplete structure of bridges, especially those constructed by
free cantilever method, under these loads is also of great importance.
Hence, this research tried to study the behavior of incomplete
structure of common bridge type (box girder bridge), in construction
phase under vertical seismic loads. Subsequently, the paper provided
suitable guidelines and solutions to resist this destructive
phenomenon. Research results proved that use of preventive methods
can significantly reduce the stresses resulted from vertical seismic
loads in box cross sections to an acceptable range recommended by
design codes.
Abstract: The problem of toughening in brittle materials
reinforced by fibers is complex, involving all of the mechanical
properties of fibers, matrix and the fiber/matrix interface, as well as
the geometry of the fiber. Development of new numerical methods
appropriate to toughening simulation and analysis is necessary. In
this work, we have performed simulations and analysis of toughening
in brittle matrix reinforced by randomly distributed fibers by means
of the discrete elements method. At first, we put forward a
mechanical model of toughening contributed by random fibers. Then
with a numerical program, we investigated the stress, damage and
bridging force in the composite material when a crack appeared in the
brittle matrix. From the results obtained, we conclude that: (i) fibers
of high strength and low elasticity modulus are beneficial to
toughening; (ii) fibers of relatively high elastic modulus compared to
the matrix may result in substantial matrix damage due to spalling
effect; (iii) employment of high-strength synthetic fibers is a good
option for toughening. We expect that the combination of the discrete
element method (DEM) with the finite element method (FEM) can
increase the versatility and efficiency of the software developed. The
present work can guide the design of ceramic composites of high
performance through the optimization of the parameters.
Abstract: The key role in phenomenological modelling of cyclic
plasticity is good understanding of stress-strain behaviour of given
material. There are many models describing behaviour of materials
using numerous parameters and constants. Combination of individual
parameters in those material models significantly determines whether
observed and predicted results are in compliance. Parameter
identification techniques such as random gradient, genetic algorithm
and sensitivity analysis are used for identification of parameters using
numerical modelling and simulation. In this paper genetic algorithm
and sensitivity analysis are used to study effect of 4 parameters of
modified AbdelKarim-Ohno cyclic plasticity model. Results
predicted by Finite Element (FE) simulation are compared with
experimental data from biaxial ratcheting test with semi-elliptical
loading path.
Abstract: This paper proposes five level diode clamped Z source
Inverter. The existing PWM techniques used for ZSI are restricted for
two level. The two level Z Source Inverter have high harmonic
distortions which effects the performance of the grid connected PV
system. To improve the performance of the system the number of
voltage levels in the output waveform need to be increased. This
paper presents comparative analysis of a five level diode clamped Z
source Inverter with different carrier based Modified Pulse Width
Modulation techniques. The parameters considered for comparison
are output voltage, voltage gain, voltage stress across switch and total
harmonic distortion when powered by same DC supply. Analytical
results are verified using MATLAB.
Abstract: Over the past four decades, the fatigue behavior of
nickel-based alloys has been widely studied. However, in recent
years, significant advances in the fabrication process leading to grain
size reduction have been made in order to improve fatigue properties
of aircraft turbine discs. Indeed, a change in particle size affects the
initiation mode of fatigue cracks as well as the fatigue life of the
material. The present study aims to investigate the fatigue behavior of
a newly developed nickel-based superalloy under biaxial-planar
loading. Low Cycle Fatigue (LCF) tests are performed at different
stress ratios so as to study the influence of the multiaxial stress state
on the fatigue life of the material. Full-field displacement and strain
measurements as well as crack initiation detection are obtained using
Digital Image Correlation (DIC) techniques. The aim of this
presentation is first to provide an in-depth description of both the
experimental set-up and protocol: the multiaxial testing machine, the
specific design of the cruciform specimen and performances of the
DIC code are introduced. Second, results for sixteen specimens
related to different load ratios are presented. Crack detection, strain
amplitude and number of cycles to crack initiation vs. triaxial stress
ratio for each loading case are given. Third, from fractographic
investigations by scanning electron microscopy it is found that the
mechanism of fatigue crack initiation does not depend on the triaxial
stress ratio and that most fatigue cracks initiate from subsurface
carbides.
Abstract: Previous studies on financial distress prediction choose
the conventional failing and non-failing dichotomy; however, the
distressed extent differs substantially among different financial
distress events. To solve the problem, “non-distressed”, “slightlydistressed”
and “reorganization and bankruptcy” are used in our article
to approximate the continuum of corporate financial health. This paper
explains different financial distress events using the two-stage method.
First, this investigation adopts firm-specific financial ratios, corporate
governance and market factors to measure the probability of various
financial distress events based on multinomial logit models.
Specifically, the bootstrapping simulation is performed to examine the
difference of estimated misclassifying cost (EMC). Second, this work
further applies macroeconomic factors to establish the credit cycle
index and determines the distressed cut-off indicator of the two-stage
models using such index. Two different models, one-stage and
two-stage prediction models are developed to forecast financial
distress, and the results acquired from different models are compared
with each other, and with the collected data. The findings show that the
one-stage model has the lower misclassification error rate than the
two-stage model. The one-stage model is more accurate than the
two-stage model.
Abstract: Power systems are operating under stressed condition
due to continuous increase in demand of load. This can lead to
voltage instability problem when face additional load increase or
contingency. In order to avoid voltage instability suitable size of
reactive power compensation at optimal location in the system is
required which improves the load margin. This work aims at
obtaining optimal size as well as location of compensation in the 39-
bus New England system with the help of Bacteria Foraging and
Genetic algorithms. To reduce the computational time the work
identifies weak candidate buses in the system, and then picks only
two of them to take part in the optimization. The objective function is
based on a recently proposed voltage stability index which takes into
account the weighted average sensitivity index is a simpler and faster
approach than the conventional CPF algorithm. BFOA has been
found to give better results compared to GA.
Abstract: The composite pavement system considered in this
paper is composed of a functional surface layer, a fiber reinforced
asphalt middle layer and a fiber reinforced lean concrete base layer.
The mix design of the fiber reinforced lean concrete corresponds to the
mix composition of conventional lean concrete but reinforced by
fibers. The quasi-absence of research on the durability or long-term
performances (fatigue, creep, etc.) of such mix design stresses the
necessity to evaluate experimentally the long-term characteristics of
this layer composition. This study tests the creep characteristics as one
of the long-term characteristics of the fiber reinforced lean concrete
layer for composite pavement using a new creep device. The test
results reveal that the lean concrete mixed with fiber reinforcement
and fly ash develops smaller creep than the conventional lean
concrete. The results of the application of the CEB-FIP prediction
equation indicate that a modified creep prediction equation should be
developed to fit with the new mix design of the layer.
Abstract: This paper presents Finite Element Method (FEM) for
analyzing the internal responses generated in thin rectangular plates
with various edge conditions and rigidity conditions. Comparison has
been made between the FEM (ANSYS software) results for
displacement, stresses and moments generated with and without the
consideration of hole in plate and different aspect ratios. In the end
comparison for responses in plain and composite square plates has
been studied.
Abstract: Diminished antioxidant defense or increased
production of reactive oxygen species in the biological system can
result in oxidative stress which may lead to various
neurodegenerative diseases including Alzheimer’s disease (AD).
Microglial activation also contributes to the progression of AD by
producing several proinflammatory cytokines, nitric oxide (NO) and
prostaglandin E2 (PGE2). Oxidative stress and inflammation have
been reported to be possible pathophysiological mechanisms
underlying AD. In addition, the cholinergic hypothesis postulates that
memory impairment in patient with AD is also associated with the
deficit of cholinergic function in the brain. Although a number of
drugs have been approved for the treatment of AD, most of these
synthetic drugs have diverse side effects and yield relatively modest
benefits. Marine algae have great potential in pharmaceutical and
biomedical applications as they are valuable sources of bioactive
properties such as anticoagulation, antimicrobial, antioxidative,
anticancer and anti-inflammatory. Hence, this study aimed to provide
an overview of the properties of Malaysian seaweeds (Padina
australis, Sargassum polycystum and Caulerpa racemosa) in
inhibiting oxidative stress, neuroinflammation and cholinesterase
enzymes. These seaweeds significantly exhibited potent DPPH and
moderate superoxide anion radical scavenging ability (P