Abstract: A simple analytical model has been developed to
optimize biasing conditions for obtaining maximum linearity among
lattice-matched, pseudomorphic and metamorphic HEMT types as
well as enhancement and depletion HEMT modes. A nonlinear
current-voltage model has been simulated based on extracted data to
study and select the most appropriate type and mode of HEMT in
terms of a given gate-source biasing voltage within the device so as
to employ the circuit for the highest possible output current or
voltage linear swing. Simulation results can be used as a basis for the
selection of optimum gate-source biasing voltage for a given type
and mode of HEMT with regard to a circuit design. The
consequences can also be a criterion for choosing the optimum type
or mode of HEMT for a predetermined biasing condition.
Abstract: Gas turbine systems with wet compression have a
potential for future power generation, since they can offer a high
efficiency and a high specific power with a relatively low cost. In this
study influence of ambient condition on the performance of the wet
compression process is investigated with a non-equilibrium analytical
modeling based on droplet evaporation. Transient behaviors of droplet
diameter and temperature of mixed air are investigated for various
ambient temperatures. Special attention is paid for the effects of
ambient temperature, pressure ratio, and water injection ratios on the
important wet compression variables including compressor outlet
temperature and compression work. Parametric studies show that
downing of the ambient temperature leads to lower compressor outlet
temperature and consequently lower consumption of compression
work even in wet compression processes.
Abstract: The development of distributed systems has been affected by the need to accommodate an increasing degree of flexibility, adaptability, and autonomy. The Mobile Agent technology is emerging as an alternative to build a smart generation of highly distributed systems. In this work, we investigate the performance aspect of agent-based technologies for information retrieval. We present a comparative performance evaluation model of Mobile Agents versus Remote Method Invocation by means of an analytical approach. We demonstrate the effectiveness of mobile agents for dynamic code deployment and remote data processing by reducing total latency and at the same time producing minimum network traffic. We argue that exploiting agent-based technologies significantly enhances the performance of distributed systems in the domain of information retrieval.
Abstract: Khatunabad area is situated geologically in Urmieh-
Dokhtar magmatic belt in NW of Iran. In this research, studied area
has been investigated in order to recognize the potential copper and
molybdenum-bearing target areas. The survey layers include the
lithologic units, alteration, geochemical result, tectonics and copper
and molybdenum occurrence. As an accurate decision can have a
considerable effect on exploration plans, so in this efforts have been
made to make use of new combination method. For this purpose, the
analytical hierarchy process was used and revealed highly potential
copper and molybdenum mineralization areas. Based on achieved
results, geological perspective in north of studied area is appropriate
for advance stage, especially for subsurface exploration in future.
Abstract: In this paper, a solution is presented for a robotic
manipulation problem in industrial settings. The problem is sensing
objects on a conveyor belt, identifying the target, planning and
tracking an interception trajectory between end effector and the
target. Such a problem could be formulated as combining object
recognition, tracking and interception. For this purpose, we integrated
a vision system to the manipulation system and employed tracking
algorithms. The control approach is implemented on a real industrial
manipulation setting, which consists of a conveyor belt, objects
moving on it, a robotic manipulator, and a visual sensor above the
conveyor. The trjectory for robotic interception at a rendezvous point
on the conveyor belt is analytically calculated. Test results show that
tracking the raget along this trajectory results in interception and
grabbing of the target object.
Abstract: An HPLC-UV analytical method was developed to
determine ethylenediaminetetraacetic acid (EDTA) in dairy
wastewater and surface water. The optimizing separation was achieved
by reversed–phase ion-pair liquid chromatography on a C18 column
using methanol as mobile phase solvent, tetrabutylammonium bromide
as the ion-pair reagent in pH 3.3 formate buffer solution at a flow rate
of 0.9 mL min-1 with a UV detector at 265 nm. No interference of Ca,
Mg or NO3
- was detected. Method performance was evaluated in terms
of linearity, repeatability and reproducibility. The method detection
limit was 5 μg L-1. The contents of EDTA in dairy effluents were 72 ~
261 μg L-1 at a large dairy site. A change of EDTA concentration was
observed downstream of the dairy effluent discharge, but this was well
under the predicted no effect concentration for aquatic ecosystem.
Abstract: The IEEE802.16 standard which has emerged as
Broadband Wireless Access (BWA) technology, promises to deliver
high data rate over large areas to a large number of subscribers in the
near future. This paper analyze the effect of overheads over capacity
of downlink (DL) of orthogonal frequency division multiple access
(OFDMA)–based on the IEEE802.16e mobile WiMAX system with
and without overheads. The analysis focuses in particular on the
impact of Adaptive Modulation and Coding (AMC) as well as
deriving an algorithm to determine the maximum numbers of
subscribers that each specific WiMAX sector may support. An
analytical study of the WiMAX propagation channel by using Cost-
231 Hata Model is presented. Numerical results and discussion
estimated by using Matlab to simulate the algorithm for different
multi-users parameters.
Abstract: This paper presents a conceptual model of agreement
options on negotiation support for civil engineering decision. The
negotiation support facilitates the solving of group choice decision
making problems in civil engineering decision to reduce the impact
of mud volcano disaster in Sidoarjo, Indonesia. The approach based
on application of analytical hierarchy process (AHP) method for
multi criteria decision on three level of decision hierarchy.
Decisions for reducing impact is very complicated since many
parties involved in a critical time. Where a number of stakeholders
are involved in choosing a single alternative from a set of solution
alternatives, there are different concern caused by differing
stakeholder preferences, experiences, and background. Therefore, a
group choice decision support is required to enable each stakeholder
to evaluate and rank the solution alternatives before engaging into
negotiation with the other stakeholders. Such civil engineering
solutions as alternatives are referred to as agreement options that are
determined by identifying the possible stakeholder choice, followed
by determining the optimal solution for each group of stakeholder.
Determination of the optimal solution is based on a game theory
model of n-person general sum game with complete information that
involves forming coalitions among stakeholders.
Abstract: A model-free robust control (MFRC) approach is proposed for position control of robot manipulators in the state space. The control approach is verified analytically to be robust subject to uncertainties including external disturbances, unmodeled dynamics, and parametric uncertainties. There is a high flexibility to work on different systems including actuators by the use of the proposed control approach. The proposed control approach can guarantee the robustness of control system. A PUMA 560 robot driven by geared permanent magnet dc motors is simulated. The simulation results show a satisfactory performance for control system under technical specifications. KeywordsModel-free, robust control, position control, PUMA 560.
Abstract: A reliable estimate of the average bond stress within
the anchorage of steel reinforcing bars in tension is critically
important for the design of reinforced concrete member. This paper
describes part of a recently completed experimental research program
in the Centre for Infrastructure Engineering and Safety (CIES) at the
University of New South Wales, Sydney, Australia aimed at
assessing the effects of different factors on the anchorage
requirements of modern high strength steel reinforcing bars. The
study found that an increase in the anchorage length and bar diameter
generally leads to a reduction of the average ultimate bond stress. By
the extension of a well established analytical model of bond and
anchorage, it is shown here that the differences in the average
ultimate bond stress for different anchorage lengths is associated with
the variable degree of plastic deformation in the tensile zone of the
concrete surrounding the bar.
Abstract: This study was carried out experimentally and analytically about the performance of solar cell panel system for operating the pump coupled by dc-motor. The solar cell panel with total area 1.9848 m2 consists of three modules of 80 Wp each. The small centrifugal pump powered by dc-motor is operated to lift water from 1m to 7m heads in sequence and gives the amount of water pumped over the whole day from 08.00 to 16.00 h are 11988, 10851, 8874, 7695, 5760, 3600, 2340 L/d respectively. The hourly global solar radiation during the day is an average of 506 W/m2. This study also presents the I-V characteristics of the panel at global radiations 200, 400, 600, 800 and 1000 W/m2 matched with the operation of the pump at the above lifting heads. It proves that the only solar radiations 800 and 1000 W/m2 could provide lifting head from 1m to 7m. The analysis shows the best efficiency point of the performance of solar cell panel system occurs at the pumping head 2.89 m.
Abstract: Malaria is transmitted to the human by biting of
infected Anopheles mosquitoes. This disease is a serious, acute and
chronic relapsing infection to humans. Fever, nausea, vomiting, back
pain, increased sweating anemia and splenomegaly (enlargement of
the spleen) are the symptoms of the patients who infected with this
disease. It is caused by the multiplication of protozoa parasite of the
genus Plasmodium. Plasmodium falciparum, Plasmodium vivax,
Plasmodium malariae and Plasmodium ovale are the four types of
Plasmodium malaria. A mathematical model for the transmission of
Plasmodium Malaria is developed in which the human and vector
population are divided into two classes, the susceptible and the
infectious classes. In this paper, we formulate the dynamical model
of Plasmodium falciparum and Plasmodium vivax malaria. The
standard dynamical analysis is used for analyzing the behavior for
the transmission of this disease. The Threshold condition is found
and numerical results are shown to confirm the analytical results.
Abstract: Software and applications are subjected to serious and damaging security threats, these threats are increasing as a result of increased number of potential vulnerabilities. Security testing is an indispensable process to validate software security requirements and to identify security related vulnerabilities. In this paper we analyze and compare different available vulnerabilities testing techniques based on a pre defined criteria using analytical hierarchy process (AHP). We have selected five testing techniques which includes Source code analysis, Fault code injection, Robustness, Stress and Penetration testing techniques. These testing techniques have been evaluated against five criteria which include cost, thoroughness, Ease of use, effectiveness and efficiency. The outcome of the study is helpful for researchers, testers and developers to understand effectiveness of each technique in its respective domain. Also the study helps to compare the inner working of testing techniques against a selected criterion to achieve optimum testing results.
Abstract: The purpose of this paper is to analyze the case of the
U.S. Pivot and to suggest an appropriate model including entry
strategies and success factors for QPS of Cable TV. The
telecommunication companies have been operating QPS including
IPTV service, which enables them to cross over broadcasting areas.
Due to this circumstance, the Cable TV operators are now concerned
and are planning to add QPS with the mobile service. Based on the
Porter's five forces model, an analytical framework has been proposed
to MVNO in Cable TV industry in the United States. As a result of this
study, MVNO in Cable TV industry has to have a clear killer
application with their sufficient contents. Subsequently, the direction
of the future Cable TV industry is proposed.
Abstract: Adolescents in Northern Uganda are at risk of teenage
pregnancies, unsafe abortions and sexually transmitted infections
(STIs). There is silence on sex both at home and school. This cross
sectional descriptive analytical study interviews a random sample of
827 students and 13 teachers on knowledge, perception and
acceptability to a comprehensive adolescent sexual and reproductive
health education in “O” and “A” level secondary schools in Gulu
District. Quantitative data was analyzed using SPSS 16.0. Directed
content analysis of themes of transcribed qualitative data was
conducted manually for common codes, sub-categories and
categories. Of the 827 students; 54.3% (449) reported being in a
sexual relationship especially those aged 15-17 years. Majority
96.1% (807) supported the teaching of a comprehensive ASRHE,
citing no negative impact 71.5% (601). Majority 81.6% (686) agreed
that such education could help prevention of STIs, abortions and
teenage pregnancies, and that it should be taught by health workers
69.0% (580). Majority 76.6% (203) reported that ASRHE was not
currently being taught in their schools. Students had low knowledge
levels and misconceptions about ASRHE. ASRHE was highly
acceptable though not being emphasized; its success in school
settings requires multidisciplinary culturally sensitive approaches
amongst which health workers should be frontiers.
Abstract: Typical Intelligent Decision Support System is 4-based, its design composes of Data Warehouse, Online Analytical Processing, Data Mining and Decision Supporting based on models, which is called Decision Support System Based on Data Warehouse (DSSBDW). This way takes ETL,OLAP and DM as its implementing means, and integrates traditional model-driving DSS and data-driving DSS into a whole. For this kind of problem, this paper analyzes the DSSBDW architecture and DW model, and discusses the following key issues: ETL designing and Realization; metadata managing technology using XML; SQL implementing, optimizing performance, data mapping in OLAP; lastly, it illustrates the designing principle and method of DW in DSSBDW.
Abstract: Video-on-demand (VOD) is designed by using content delivery networks (CDN) to minimize the overall operational cost and to maximize scalability. Estimation of the viewing pattern (i.e., the relationship between the number of viewings and the ranking of VOD contents) plays an important role in minimizing the total operational cost and maximizing the performance of the VOD systems. In this paper, we have analyzed a large body of commercial VOD viewing data and found that the viewing rank distribution fits well with the parabolic fractal distribution. The weighted linear model fitting function is used to estimate the parameters (coefficients) of the parabolic fractal distribution. This paper presents an analytical basis for designing an optimal hierarchical VOD contents distribution system in terms of its cost and performance.
Abstract: Biometric measures of one kind or another have been
used to identify people since ancient times, with handwritten
signatures, facial features, and fingerprints being the traditional
methods. Of late, Systems have been built that automate the task of
recognition, using these methods and newer ones, such as hand
geometry, voiceprints and iris patterns. These systems have different
strengths and weaknesses. This work is a two-section composition. In
the starting section, we present an analytical and comparative study
of common biometric techniques. The performance of each of them
has been viewed and then tabularized as a result. The latter section
involves the actual implementation of the techniques under
consideration that has been done using a state of the art tool called,
MATLAB. This tool aids to effectively portray the corresponding
results and effects.
Abstract: There are many sources trough which the soil get
enriched and contaminated with REEs. The determination of REEs in
environmental samples has been limited because of the lack of
sensitive analytical techniques. Soil samples were collected from
four sites including open cast coal mine, natural coal burning, coal
washery and control in the coal field located in Dhanbad, India.
Total concentrations of rare earth elements (REEs) were determined
using the inductively coupled plasma atomic absorption spectrometry
in order to assess enrichment status in the coal field. Results showed
that the mean concentrations of La, Pr, Eu, Tb, Ho, and Tm in open
cast mine and natural coal burning sites were elevated compared to
the reference concentrations, while Ce, Nd, Sm, and Gd were
elevated in coal washery site. When compared to reference soil,
heavy REEs (HREEs) were enriched in open cast mines and natural
coal burning affected soils, however, the HREEs were depleted in the
coal washery sites. But, the Chondrite-normalization diagram showed
significant enrichment for light REEs (LREEs) in all the soils. High
concentration of Pr, Eu, Tb, Ho, Tm, and Lu in coal mining and coal
burning sites may pose human health risks. Factor analysis showed
that distribution and relative abundance of REEs of the coal washery
site is comparable with the control. Eventually washing or cleaning
of coal could significantly decrease the emission of REEs from coal
into the environment.
Abstract: A camera in the building site is exposed to different
weather conditions. Differences between images of the same scene
captured with the same camera arise also due to temperature variations.
The influence of temperature changes on camera parameters
were modelled and integrated into existing analytical camera model.
Modified camera model enables quantitatively assessing the influence
of temperature variations.