Abstract: The flow field over a three dimensional pole barn
characterized by a cylindrical roof has been numerically investigated.
Wind pressure and viscous loads acting on the agricultural building
have been analyzed for several incoming wind directions, so as to
evaluate the most critical load condition on the structure. A constant
wind velocity profile, based on the maximum reference wind speed in
the building site (peak gust speed worked out for 50 years return
period) and on the local roughness coefficient, has been simulated.
In order to contemplate also the hazard due to potential air
wedging between the stored hay and the lower part of the ceiling, the
effect of a partial filling of the barn has been investigated.
The distribution of wind-induced loads on the structure have been
determined, allowing a numerical quantification of the effect of wind
direction on the induced stresses acting on a hemicylindrical roof.
Abstract: The aerodynamic noise radiation from a side view mirror (SVM) in the high-speed airflow is calculated by the combination of unsteady incompressible fluid flow analysis and acoustic analysis. The transient flow past the generic SVM is simulated with variable turbulence model, namely DES Detached Eddy Simulation and LES (Large Eddy Simulation). Detailed velocity vectors and contour plots of the time-varying velocity and pressure fields are presented along cut planes in the flow-field. Mean and transient pressure are also monitored at several points in the flow field and compared to corresponding experimentally data published in literature. The acoustic predictions made using the Ffowcs-Williams-Hawkins acoustic analogy (FW-H) and the boundary element (BEM).
Abstract: This was the first document revealing the
investigation of protein hydrolysate production optimization from J.
curcas cake. Proximate analysis of raw material showed 18.98%
protein, 5.31% ash, 8.52% moisture and 12.18% lipid. The
appropriate protein hydrolysate production process began with
grinding the J. curcas cake into small pieces. Then it was suspended
in 2.5% sodium hydroxide solution with ratio between solution/ J.
curcas cake at 80:1 (v/w). The hydrolysis reaction was controlled at
temperature 50 °C in water bath for 45 minutes. After that, the
supernatant (protein hydrolysate) was separated using centrifuge at
8000g for 30 minutes. The maximum yield of resulting protein
hydrolysate was 73.27 % with 7.34% moisture, 71.69% total protein,
7.12% lipid, 2.49% ash. The product was also capable of well
dissolving in water.
Abstract: As the majority of faults are found in a few of its
modules so there is a need to investigate the modules that are
affected severely as compared to other modules and proper
maintenance need to be done in time especially for the critical
applications. As, Neural networks, which have been already applied
in software engineering applications to build reliability growth
models predict the gross change or reusability metrics. Neural
networks are non-linear sophisticated modeling techniques that are
able to model complex functions. Neural network techniques are
used when exact nature of input and outputs is not known. A key
feature is that they learn the relationship between input and output
through training. In this present work, various Neural Network Based
techniques are explored and comparative analysis is performed for
the prediction of level of need of maintenance by predicting level
severity of faults present in NASA-s public domain defect dataset.
The comparison of different algorithms is made on the basis of Mean
Absolute Error, Root Mean Square Error and Accuracy Values. It is
concluded that Generalized Regression Networks is the best
algorithm for classification of the software components into different
level of severity of impact of the faults. The algorithm can be used to
develop model that can be used for identifying modules that are
heavily affected by the faults.
Abstract: Since the late 1980s, the new phenomena of 'employment subcentres' or 'polycentricity' has appeared in the metropolises of North American and Western Europe and it has been an interesting topic for academics and researchers. This paper specifically uses one case study-Guangzhou to explore the development and the mechanism of employment subcentres and polycentricity in Chinese metropolises by spatial analysis method on the basis of the first economic census data. In conclusion, the paper regards that the employment subcentres and polycentricity has existed in Chinese metropolises. And that, the mechanism of them is mainly from the secondary industry instead of the tertiary industry in North American and Western Europe
Abstract: The recent global financial problem urges government
to play role in stimulating the economy due to the fact that private
sector has little ability to purchase during the recession. A concerned
question is whether the increased government spending crowds out
private consumption and whether it helps stimulate the economy. If
the government spending policy is effective; the private consumption
is expected to increase and can compensate the recent extra
government expense. In this study, the government spending is
categorized into government consumption spending and government
capital spending. The study firstly examines consumer consumption
along the line with the demand function in microeconomic theory.
Three categories of private consumption are used in the study. Those
are food consumption, non food consumption, and services
consumption. The dynamic Almost Ideal Demand System of the three
categories of the private consumption is estimated using the Vector
Error Correction Mechanism model. The estimated model indicates
the substituting effects (negative impacts) of the government
consumption spending on budget shares of private non food
consumption and of the government capital spending on budget share
of private food consumption, respectively. Nevertheless the result
does not necessarily indicate whether the negative effects of changes
in the budget shares of the non food and the food consumption means
fallen total private consumption. Microeconomic consumer demand
analysis clearly indicates changes in component structure of
aggregate expenditure in the economy as a result of the government
spending policy. The macroeconomic concept of aggregate demand
comprising consumption, investment, government spending (the
government consumption spending and the government capital
spending), export, and import are used to estimate for their
relationship using the Vector Error Correction Mechanism model.
The macroeconomic study found no effect of the government capital
spending on either the private consumption or the growth of GDP
while the government consumption spending has negative effect on
the growth of GDP. Therefore no crowding out effect of the
government spending is found on the private consumption but it is
ineffective and even inefficient expenditure as found reducing growth
of the GDP in the context of Thailand.
Abstract: Power Spectral Density (PSD) of quasi-stationary processes can be efficiently estimated using the short time Fourier series (STFT). In this paper, an algorithm has been proposed that computes the PSD of quasi-stationary process efficiently using offline autoregressive model order estimation algorithm, recursive parameter estimation technique and modified sliding window discrete Fourier Transform algorithm. The main difference in this algorithm and STFT is that the sliding window (SW) and window for spectral estimation (WSA) are separately defined. WSA is updated and its PSD is computed only when change in statistics is detected in the SW. The computational complexity of the proposed algorithm is found to be lesser than that for standard STFT technique.
Abstract: Pattern recognition and image recognition methods are commonly developed and tested using testbeds, which contain known responses to a query set. Until now, testbeds available for image analysis and content-based image retrieval (CBIR) have been scarce and small-scale. Here we present the one million images CEA-List Image Collection (CLIC) testbed that we have produced, and report on our use of this testbed to evaluate image analysis merging techniques. This testbed will soon be made publicly available through the EU MUSCLE Network of Excellence.
Abstract: In this paper, we analyzed the pattern of urban spatial structure of Siheung City that had been divided into two parts and presented alternative plans in order to get rid of these phenomena. Concerning patterns of urban spatial structure, we examined it through means of analyzing status of land use, population density and distribution of residence, status of distribution of main facilities, medical facilities, status of distribution of cultural facilities, distribution of land prices and traffic volume trends. The results of study revealed that status of facilities distribution and distribution of land prices, etc. were bisected by the surrounding area of former municipal office and the district of Sihwa, which were both regarded as one apex of the city divide, forming a duo-centric city. In order to get rid of this problem concerned with urban spatial structure that has been bisected, it is required that measures in order to expand facilities in Siheung City should be taken.
Abstract: The wide increase and diffusion on telecommunication
technologies have caused a huge spread of electromagnetic sources
in most European Countries. Since the public is continuously being
exposed to electromagnetic radiation the possible health effects have
become the focus of population concerns. As a result, electromagnetic
field monitoring stations which control field strength in commercial
frequency bands are being placed on the flat roof of many buildings.
However there is no guidance on where to place them. This paper
presents an analysis of frequency, polarization and angles of incidence
of a plane wave which impinges on a flat roof security wall and its
dependence on electromagnetic field strength meters placement.
Abstract: The aim of the research is to understand whether the accuracy of customer detection of employee emotional labor strategy would influence the overall service satisfaction. From path analysis, it was found that employee-s positive emotions positively influenced service quality. Service quality in turn influenced Customer detection of employee emotional deep action strategy and Customer detection of employee emotional surface action strategy. Lastly, Customer detection of employee emotional deep action strategy and Customer detection of employee emotional surface action strategy positively influenced service satisfaction. Based on the analysis results, suggestions are proposed to provide reference for human resource management and use in relative fields.
Abstract: For the efficient and safe use of the cable-stayed
bridge, a design based on the detailed local analysis of the cable anchor
system is required. Also, a theoretical design process for the anchor
system should be prepared and reviewed. Generally, the size of the
fixing pipe in the anchor system is decided according to the
specifications prepared by cable-manufacturing companies, and
accordingly, there is difficulty determining the initial inner diameters
of the fixing pipes. As such, there is no choice but to use the products
with the existing sizes. In this study, the existing design process of the
fixing pipe, is a type of guide pipe anchor in the cable anchor system,
is reviewed, a formula determining the thickness of the fixing pipe is
proposed, and the convenience and validity of the suggested equation
is compared with the results of the existing designs to verify its
convenience and validity.
Abstract: The flow and heat transfer mechanism in convex
corrugated tubes have been investigated through numerical
simulations in this paper. Two kinds of tube types named as symmetric
corrugated tube (SCT) and asymmetric corrugated tube (ACT) are
modeled and studied numerically based on the RST model. The
predictive capability of RST model is examined in the corrugation wall
in order to check the reliability of RST model under the corrugation
wall condition. We propose a comparison between the RST modelling
the corrugation wall with existing direct numerical simulation of Maaß
C and Schumann U [14]. The numerical results pressure coefficient at
different profiles between RST and DNS are well matched. The
influences of large corrugation tough radii to heat transfer and flow
characteristic had been considered. Flow and heat transfer comparison
between SCT and ACT had been discussed. The numerical results
show that ACT exhibits higher overall heat transfer performance than
SCT.
Abstract: Nowadays, butyl acetate, a pineapple flavor has been applied widely in food, beverage, cosmetic and pharmaceutical industries. In this study, Butyl acetate, a flavor ester was successfully synthesized via green synthesis of enzymatic reaction route. Commercial immobilized lipase from Rhizomucor miehei (Lipozyme RMIM) was used as biocatalyst in the esterification reaction between acetic acid and butanol. Various reaction parameters such as reaction time (RT), temperature (T) and amount of enzyme (E) were chosen to optimize the reaction synthesis in solvent-free system. The optimum condition to produce butyl acetate was at reaction time (RT), 18 hours; temperature (T), 37°C and amount of enzyme, 25 % (w/w of total substrate). Analysis of yield showed that at optimum condition, >78 % of butyl acetate was produced. The product was confirmed as butyl acetate from FTIR analysis whereby the presence of an ester group was observed at wavenumber of 1742 cm-1.
Abstract: Dorsal hand vein pattern is an emerging biometric which is attracting the attention of researchers, of late. Research is being carried out on existing techniques in the hope of improving them or finding more efficient ones. In this work, Principle Component Analysis (PCA) , which is a successful method, originally applied on face biometric is being modified using Cholesky decomposition and Lanczos algorithm to extract the dorsal hand vein features. This modified technique decreases the number of computation and hence decreases the processing time. The eigenveins were successfully computed and projected onto the vein space. The system was tested on a database of 200 images and using a threshold value of 0.9 to obtain the False Acceptance Rate (FAR) and False Rejection Rate (FRR). This modified algorithm is desirable when developing biometric security system since it significantly decreases the matching time.
Abstract: The modeling of inelastic behavior of plastic materials requires measurements providing information on material response to different multiaxial loading conditions. Different triaxiality conditions and values of Lode parameters have to be
covered for complex description of the material plastic behavior.
Samples geometries providing material plastic behavoiur over the range of interest are proposed with the use of FEM analysis. Round samples with 3 different notches and smooth surface are used
together with butterfly type of samples tested at angle ranging for 0 to
90°. Identification of ductile damage parameters is carried out on
the basis of obtained experimental data for austenitic stainless steel.
The obtained material plastic damage parameters are subsequently applied to FEM simulation of notched CT normally samples used for
fracture mechanics testing and results from the simulation are
compared with real tests.
Abstract: The energy consumption and delay in read/write
operation of conventional SRAM is investigated analytically as well
as by simulation. Explicit analytical expressions for the energy
consumption and delay in read and write operation as a function of
device parameters and supply voltage are derived. The expressions are
useful in predicting the effect of parameter changes on the energy
consumption and speed as well as in optimizing the design of
conventional SRAM. HSPICE simulation in standard 0.25μm CMOS
technology confirms precision of analytical expressions derived from
this paper.
Abstract: Virtual Assembly (VA) is one of the key technologies
in advanced manufacturing field. It is a promising application of
virtual reality in design and manufacturing field. It has drawn much
interest from industries and research institutes in the last two decades.
This paper describes a process for integrating an interactive Virtual
Reality-based assembly simulation of a digital mockup with the
CAD/CAM infrastructure. The necessary hardware and software
preconditions for the process are explained so that it can easily be
adopted by non VR experts. The article outlines how assembly
simulation can improve the CAD/CAM procedures and structures;
how CAD model preparations have to be carried out and which
virtual environment requirements have to be fulfilled. The issue of
data transfer is also explained in the paper. The other challenges and
requirements like anti-aliasing and collision detection have also been
explained. Finally, a VA simulation has been carried out for a ball
valve assembly and a car door assembly with the help of Vizard
virtual reality toolkit in a semi-immersive environment and their
performance analysis has been done on different workstations to
evaluate the importance of graphical processing unit (GPU) in the
field of VA.
Abstract: Modern times call organizations to have an active role
in the social arena, through Corporate Social Responsibility (CSR).
The objective of this research was to test the hypothesis that there is a
positive relation between social performance and economic
performance, and if there is a positive correlation between social
performance and financial-economic performance. To test these
theories a measure of social performance, based on the Green Book
of Commission of the European Community, was used in a group of
nineteen Portuguese top companies, listed on the PSI 20 index,
through a period of five years, since 2005 to 2009. A clusters
analysis was applied to group companies by their social performance
and to compare and correlate their economic performance. Results
indicate that companies that had a better social performance are not
the ones who had a better economic performance, and suggest that
the middle path might provide a good relation CSR-Economic
performance, as a basis to a sustainable development.
Abstract: As known, the guard wires of overhead high voltage
are usually grounded through the grounding systems of support and
of the terminal stations. They do affect the zero sequence impedance
value of the line, Z0, which is generally, calculated assuming that the
wires guard are at ground potential. In this way it is not considered
the effect of the resistances of earth of supports and stations. In this
work is formed a formula for the calculation of Z0 which takes
account of said resistances. Is also proposed a method of calculating
the impedance zero sequence overhead lines in which, in various
sections or spans, the guard wires are connected to the supports, or
isolated from them, or are absent. Parametric analysis is given for
lines 220 kV and 400 kV, which shows the extent of the errors made
with traditional methods of calculation.