Abstract: This paper aims to initiate an analytical account of the
issues of compliance with economy condition for incentive pay
system application in an enterprise. Economy is considered one of the
conditions for effective incentive pay system application another
condition being the achievement of desired efficiency level of the
incentive pay system application. Bonus pay system is discussed as
an example.
Abstract: In this work, are discussed two formulations of the boundary element method - BEM to perform linear bending analysis of plates reinforced by beams. Both formulations are based on the Kirchhoff's hypothesis and they are obtained from the reciprocity theorem applied to zoned plates, where each sub-region defines a beam or a slab. In the first model the problem values are defined along the interfaces and the external boundary. Then, in order to reduce the number of degrees of freedom kinematics hypothesis are assumed along the beam cross section, leading to a second formulation where the collocation points are defined along the beam skeleton, instead of being placed on interfaces. On these formulations no approximation of the generalized forces along the interface is required. Moreover, compatibility and equilibrium conditions along the interface are automatically imposed by the integral equation. Thus, these formulations require less approximation and the total number of the degree s of freedom is reduced. In the numerical examples are discussed the differences between these two BEM formulations, comparing as well the results to a well-known finite element code.
Abstract: Blind signatures enable users to obtain valid signatures for a message without revealing its content to the signer. This paper presents a new blind signature scheme, i.e. identity-based blind signature scheme with message recovery. Due to the message recovery property, the new scheme requires less bandwidth than the identitybased blind signatures with similar constructions. The scheme is based on modified Weil/Tate pairings over elliptic curves, and thus requires smaller key sizes for the same level of security compared to previous approaches not utilizing bilinear pairings. Security and efficiency analysis for the scheme is provided in this paper.
Abstract: The aim of this paper is to know the sociodemographic
and operational-financial determinants of the services
quality perceived by users of the national health services. Through
the use of an inquiry conducted by the Ministry of Health,
comprehending 16.936 interviews in 2006, we intend to find out if
there is any characteristic that determines the 2006 inquiry results.
With the revision of the literature we also want to know if the
operational-financial results have implications in hospitals users-
perception on the quality of the received services. In order to achieve
our main goals we will make use of the regression analysis to find out
the possible dimensions that determine those results.
Abstract: Names are important in many societies, even in technologically oriented ones which use e.g. ID systems to identify individual people. Names such as surnames are the most important as they are used in many processes, such as identifying of people and genealogical research. On the other hand variation of names can be a major problem for the identification and search for people, e.g. web search or security reasons. Name matching presumes a-priori that the recorded name written in one alphabet reflects the phonetic identity of two samples or some transcription error in copying a previously recorded name. We add to this the lode that the two names imply the same person. This paper describes name variations and some basic description of various name matching algorithms developed to overcome name variation and to find reasonable variants of names which can be used to further increasing mismatches for record linkage and name search. The implementation contains algorithms for computing a range of fuzzy matching based on different types of algorithms, e.g. composite and hybrid methods and allowing us to test and measure algorithms for accuracy. NYSIIS, LIG2 and Phonex have been shown to perform well and provided sufficient flexibility to be included in the linkage/matching process for optimising name searching.
Abstract: This paper presents a hybrid association control
scheme that can maintain load balancing among access points in the
wireless LANs and can satisfy the quality of service requirements of
the multimedia traffic applications. The proposed model is
mathematically described as a linear programming model. Simulation
study and analysis were conducted in order to demonstrate the
performance of the proposed hybrid load balancing and association
control scheme. Simulation results shows that the proposed scheme
outperforms the other schemes in term of the percentage of blocking
and the quality of the data transfer rate providing to the multimedia
and real-time applications.
Abstract: The curriculum of the primary school science course was redesigned on the basis of constructivism in 2005-2006 academic years, in Turkey. In this context, the name of this course has been changed as “Science and Technology"; and both content and course books, students workbooks for this course have been redesigned in light of constructivism. The aim of this study is to determine whether the Science and Technology course books and student work books for primary school 5th grade are appropriate for the constructivism by evaluating them in terms of the fundamental principles of constructivism. In this study, out of qualitative research methods, documentation technique (i.e. document analysis) is applied; while selecting samples, criterion-sampling is used out of purposeful sampling techniques. When the Science and Technology course book and workbook for the 5th grade in primary education are examined, it is seen that both books complete each other in certain areas. Consequently, it can be claimed that in spite of some inadequate and missing points in the course book and workbook of the primary school Science and Technology course for the 5th grade students, these books are attempted to be designed in terms of the principles of constructivism. To overcome the inadequacies in the books, it can be suggested to redesign them. In addition to them, not to ignore the technology dimension of the course, the activities that encourage the students to prepare projects using technology cycle should be included.
Abstract: Decision support based upon risk analysis into
comparison of the electricity generation from different renewable
energy technologies can provide information about their effects on
the environment and society. The aim of this paper is to develop the
assessment framework regarding risks to health and environment,
and the society-s benefits of the electric power plant generation from
different renewable sources. The multicriteria framework to
multiattribute risk analysis technique and the decision analysis
interview technique are applied in order to support the decisionmaking
process for the implementing renewable energy projects to
the Bangkok case study. Having analyses the local conditions and
appropriate technologies, five renewable power plants are postulated
as options. As this work demonstrates, the analysis can provide a tool
to aid decision-makers for achieving targets related to promote
sustainable energy system.
Abstract: This paper reports our analysis of 163 ks observations
of PSR J0538+2817 with the Rossi X-Ray Timing Explorer
(RXTE).The pulse profiles, detected up to 60 keV, show a single
peak asin the case for radio frequency. The profile is well described
by one Gaussians function with full width at half maximum (FWHM)
0.04794. We compared the difference of arrival time between radio
and X-ray pulse profiles for the first time. It turns out that the phase
of radio emits precede the X-ray by 8.7 ± 4.5 ms. Furthermore we
obtained the pulse profiles in the energy ranges of 2.29-6.18 keV,
6.18-12.63 keV and 12.63-17.36 keV. The intensity of pulses
decreases with the increasing energy range. We discuss the emission
geometry in our work.
Abstract: In this paper an analysis of blackouts in electric power
transmission systems is implemented using a model and studied in
simple networks with a regular topology. The proposed model
describes load demand and network improvements evolving on a
slow timescale as well as the fast dynamics of cascading overloads
and outages.
Abstract: Water vapour transport properties of gypsum block
are studied in dependence on relative humidity using inverse analysis
based on genetic algorithm. The computational inverse analysis is
performed for the relative humidity profiles measured along the
longitudinal axis of a rod sample. Within the performed transient
experiment, the studied sample is exposed to two environments with
different relative humidity, whereas the temperature is kept constant.
For the basic gypsum characterisation and for the assessment of input
material parameters necessary for computational application of
genetic algorithm, the basic material properties of gypsum are
measured as well as its thermal and water vapour storage parameters.
On the basis of application of genetic algorithm, the relative
humidity dependent water vapour diffusion coefficient and water
vapour diffusion resistance factor are calculated.
Abstract: In the stadium structure, the significant dynamic
responses such as resonance or similar behavior can be occurred by
spectator rhythmical activities. Thus, accurate analysis and precise
investigation of stadium structure that is subjected to dynamic loads
are required for practical design and serviceability check of stadium
structures. Moreover, it is desirable to measure and analyze the
dynamic loads of spectator activities because these dynamic loads can
not be easily expressed in numerical formula. In this study, various
dynamic loads induced by spectator movements are measured and
analyzed. These dynamic loads induced by spectators movement of
stadium structure can be classified into the impact load and the
periodic load. These dynamic loads can be expressed as Fourier
harmonic load. And, these dynamic loads could be applied for the
accurate vibration analysis of a stadium structure.
Abstract: The feature of HIV genome is in a wide range because
of it is highly heterogeneous. Hence, the infection ability of the virus changes related with different chemokine receptors. From this point,
R5 and X4 HIV viruses use CCR5 and CXCR5 coreceptors respectively while R5X4 viruses can utilize both coreceptors. Recently, in Bioinformatics, R5X4 viruses have been studied to
classify by using the coreceptors of HIV genome.
The aim of this study is to develop the optimal Multilayer
Perceptron (MLP) for high classification accuracy of HIV sub-type viruses. To accomplish this purpose, the unit number in hidden layer
was incremented one by one, from one to a particular number. The statistical data of R5X4, R5 and X4 viruses was preprocessed by the
signal processing methods. Accessible residues of these virus sequences were extracted and modeled by Auto-Regressive Model
(AR) due to the dimension of residues is large and different from each other. Finally the pre-processed dataset was used to evolve MLP with various number of hidden units to determine R5X4
viruses. Furthermore, ROC analysis was used to figure out the optimal MLP structure.
Abstract: The main goal of the article is to present new model of
application architecture of banking IT solution providing the Internet
Banking services that is particularly outsourced. At first, we propose
business rationale and a SWOT analysis to explain the reasons for the
model in the article. The most important factor for our model is
nowadays- big boom around smart phones and tablet devices. As
next, we focus on IT architecture viewpoint where we design
application, integration and security model. Finally, we propose a
generic governance model that serves as a basis for the specialized
governance model. The specialized instance of governance model is
designed to ensure that the development and the maintenance of
different parts of the IT solution are well governed in time.
Abstract: Systems Analysis and Design is a key subject in
Information Technology courses, but students do not find it easy to
cope with, since it is not “precise" like programming and not exact
like Mathematics. It is a subject working with many concepts,
modeling ideas into visual representations and then translating the
pictures into a real life system. To complicate matters users who are
not necessarily familiar with computers need to give their inputs to
ensure that they get the system the need. Systems Analysis and
Design also covers two fields, namely Analysis, focusing on the
analysis of the existing system and Design, focusing on the design of
the new system. To be able to test the analysis and design of a
system, it is necessary to develop a system or at least a prototype of
the system to test the validity of the analysis and design. The skills
necessary in each aspect differs vastly. Project Management Skills,
Database Knowledge and Object Oriented Principles are all
necessary. In the context of a developing country where students
enter tertiary education underprepared and the digital divide is alive
and well, students need to be motivated to learn the necessary skills,
get an opportunity to test it in a “live" but protected environment –
within the framework of a university. The purpose of this article is to
improve the learning experience in Systems Analysis and Design
through reviewing the underlying teaching principles used, the
teaching tools implemented, the observations made and the
reflections that will influence future developments in Systems
Analysis and Design. Action research principles allows the focus to
be on a few problematic aspects during a particular semester.
Abstract: Chemical and physical functionalization of multiwalled
carbon nanotubes (MWCNT) has been commonly practiced to
achieve better dispersion of carbon nanotubes (CNTs) in polymer
matrix. This work describes various functionalization methods (acidtreatment,
non-ionic surfactant treatment with TritonX-100),
fabrication of MWCNT/PP nanocomposites via melt blending and
characterization of mechanical properties. Microscopy analysis
(FESEM, TEM, XPS) showed effective purification of MWCNTs
under acid treatment, and better dispersion under both chemical and
physical functionalization techniques combined, in their respective
order. Tensile tests showed increase in tensile strength for the
nanocomposites that contain MWCNTs up to 2 wt%. A decrease in
tensile strength was seen in samples that contain 4 wt% of MWCNTs
for both raw and Triton X-100 functionalized, signifying MWCNT
degradation/rebundling at composition with higher content of
MWCNTs. For the acid-treated MWCNTs, however, the tensile
results showed slight improvement even at 4wt%, indicating effective
dispersion of MWCNTs.
Abstract: Three dimensional simulations are carried out to estimate the effect of wind direction, wind speed and geometry on the flow and dispersion of vehicular pollutant in a street canyon. The pollutant sources are motor vehicles passing between the two buildings. Suitable emission factors for petrol and diesel vehicles at varying vehicle speed are used for the estimation of the rate of emission from the streets. The dispersion of automobile pollutant released from the street is simulated by introducing vehicular emission source term as a fixed-flux boundary condition at the ground level over the road. The emission source term is suitably calculated by adopting emission factors from literature for varying conditions of street traffic. It is observed that increase in wind angle disturbs the symmetric pattern of pollution distribution along the street length. The concentration increases in the far end of the street as compared to the near end.
Abstract: Wind energy has been shown to be one of the most
viable sources of renewable energy. With current technology, the low
cost of wind energy is competitive with more conventional sources of
energy such as coal. Most blades available for commercial grade
wind turbines incorporate a straight span-wise profile and airfoil
shaped cross sections. These blades are found to be very efficient at
lower wind speeds in comparison to the potential energy that can be
extracted. However as the oncoming wind speed increases the
efficiency of the blades decreases as they approach a stall point. This
paper explores the possibility of increasing the efficiency of the
blades at higher wind speeds while maintaining efficiency at the
lower wind speeds. The design intends to maintain efficiency at
lower wind speeds by selecting the appropriate orientation and size
of the airfoil cross sections based on a low oncoming wind speed and
given constant rotation rate. The blades will be made more efficient
at higher wind speeds by implementing a swept blade profile.
Performance was investigated using the computational fluid
dynamics (CFD).
Abstract: In this study, Li4SiO4 powder was successfully
synthesized via sol gel method followed by drying at 150oC. Lithium
oxide, Li2O and silicon oxide, SiO2 were used as the starting
materials with citric acid as the chelating agent. The obtained powder
was then sintered at various temperatures. Crystallographic phase
analysis, morphology and ionic conductivity were investigated
systematically employing X-ray diffraction, Fourier Transform
Infrared, Scanning Electron Microscopy and AC impedance
spectroscopy. XRD result showed the formation of pure monoclinic
Li4SiO4 crystal structure with lattice parameters a = 5.140 Å, b =
6.094 Å, c = 5.293 Å, β = 90o in the sample sintered at 750oC. This
observation was confirmed by FTIR analysis. The bulk conductivity
of this sample at room temperature was 3.35 × 10-6 S cm-1 and the
highest bulk conductivity of 1.16 × 10-4 S cm-1 was obtained at
100°C. The results indicated that, the Li4SiO4 compound has
potential to be used as host for LISICON structured solid electrolyte
for low temperature application.
Abstract: Professions are concerned about the public image they
have, and this public image is represented by stereotypes. Research is
needed to understand how accountants are perceived by different
actors in the society in different contexts, which would allow
universities, professional bodies and employers to adjust their
strategies to attract the right people to the profession and their
organizations. We aim to develop in this paper a framework to be
used in empirical testing in different environments to determine and
analyze the accountant-s stereotype. This framework will be useful in
analyzing the nuances associated to the accountant-s image and in
understanding the factors that may lead to uniformity in the
profession and of those leading to diversity from one context
(country, type of countries, region) to another.