Abstract: This study examines causal link between energy use and economic growth for five South Asian countries over period 1971-2006. Panel cointegration, ECM and FMOLS are applied for short and long run estimates. In short run unidirectional causality from per capita GDP to per capita energy consumption is found, but not vice versa. In long run one percent increase in per capita energy consumption tend to decrease 0.13 percent per capita GDP. i.e. Energy use discourage economic growth. This short and long run relationship indicate energy shortage crisis in South Asia due to increased energy use coupled with insufficient energy supply. Beside this long run estimated coefficient of error term suggest that short term adjustment to equilibrium are driven by adjustment back to long run equilibrium. Moreover, per capita energy consumption is responsive to adjustment back to equilibrium and it takes 59 years approximately. It specifies long run feedback between both variables.
Abstract: The article deals with pneumatic and hot wire
anemometry measurement on subsonic axi-symmetric air ejector.
Performances of the ejector with and without pulsations of primary
flow are compared, measuring of characteristic pressures and mass
flow rates are performed and ejector efficiency is evaluated. The
pulsations of primary flow are produced by a synthetic jet generator,
which is placed in the supply line of the primary flow just in front of
the primary nozzle. The aim of the pulsation is to intensify the
mixing process. In the article we present: Pressure measuring of
pulsation on the mixing chamber wall, behind the mixing chamber
and behind the diffuser measured by fast pressure transducers and
results of hot wire anemometry measurement. It was found out that
using of primary flow pulsations yields higher back pressure behind
the ejector and higher efficiency. The processes in this ejector and
influences of primary flow pulsations on the mixing processes are
described.
Abstract: The purpose of this paper is to highlight the
importance of the concept of competitiveness in the supply chain and
to present a conceptual framework for Supply Chain Competitiveness
(SCC). The framework is based on supply chain activities, which are
inputs, necessary for SCC and the benefits which are the outputs of
SCC. A literature review is conducted on key supply chain
competitiveness issues, its determinants, its various dimensions
followed by exploration for SCC. Based on the insights gained, a
conceptual framework for SCC is presented based on activities for
SCC, SCC environment and outcomes of SCC. The information flow
in the conceptual framework is bi-directional at all levels and the
activities are interrelated in a global competitive environment. The
activities include the activities of suppliers, manufacturers and
distributors, giving more emphasis on manufacturers- activities.
Further, implications of various factors such as economic, politicolegal,
technical, socio-cultural, competition, demographic etc. are
also highlighted. The SCC framework is an attempt to cover the
relatively less explored area of supply chain competitiveness. It is
expected that this work will further motivate researchers,
academicians and practitioners to work in this area and offers
conceptual help in providing a directions for supply chain
competitiveness which leads to improvement in the supply chain and
supply chain performance.
Abstract: ERP systems are often supposed to be implemented
and deployed in multi-national companies. On the other hand, an
ERP developer may plan to market and sale its product in various
countries. Therefore, an EPR system should have the ability to
communicate with its users, who usually have different languages
and cultures, in a suitable way. EPR support of Multilanguage
capability is a solution to achieve this objective. In this paper, an
agent oriented architecture including several independent but
cooperative agents has been suggested that helps to implement
Multilanguage EPR systems.
Abstract: Wireless sensor networks (WSNs) consist of number
of tiny, low cost and low power sensor nodes to monitor some physical phenomenon. The major limitation in these networks is the use of non-rechargeable battery having limited power supply. The
main cause of energy consumption in such networks is
communication subsystem. This paper presents an energy efficient
Cluster Cooperative Caching at Sensor (C3S) based upon grid type clustering. Sensor nodes belonging to the same cluster/grid form a
cooperative cache system for the node since the cost for
communication with them is low both in terms of energy
consumption and message exchanges. The proposed scheme uses
cache admission control and utility based data replacement policy to
ensure that more useful data is retained in the local cache of a node.
Simulation results demonstrate that C3S scheme performs better in
various performance metrics than NICoCa which is existing
cooperative caching protocol for WSNs.
Abstract: The intent of this essay is to evaluate the effectiveness
of surge suppressor aimed at power supply used for automation
devices in power distribution system which is consist of MOV and
T type low-pass filter. Books, journal articles and e-sources related
to surge protection of power supply used for automation devices in
power distribution system were consulted, and the useful information
was organized, analyzed and developed into five parts: characteristics
of surge wave, protection against surge wave, impedance characteristics
of target, using Matlab to simulate circuit response after
5kV,1.2/50s surge wave and suggestions for surge protection. The
results indicate that various types of load situation have great impact
on the effectiveness of surge protective device. Therefore, type and
parameters of surge protective device need to be carefully selected,
and load matching is also vital to be concerned.
Abstract: This research was conducted in the Pua Watershed whereas located in the Upper Nan River Basin in Nan province, Thailand. Nan River basin originated in Nan province that comprises of many tributary streams to produce as inflow to the Sirikit dam provided huge reservoir with the storage capacity of 9510 million cubic meters. The common problems of most watersheds were found i.e. shortage water supply for consumption and agriculture utilizations, deteriorate of water quality, flood and landslide including debris flow, and unstable of riverbank. The Pua Watershed is one of several small river basins that flow through the Nan River Basin. The watershed includes 404 km2 representing the Pua District, the Upper Nan Basin, or the whole Nan River Basin, of 61.5%, 18.2% or 1.2% respectively. The Pua River is a main stream producing all year streamflow supplying the Pua District and an inflow to the Upper Nan Basin. Its length approximately 56.3 kilometers with an average slope of the channel by 1.9% measured. A diversion weir namely Pua weir bound the plain and mountainous areas with a very steep slope of the riverbed to 2.9% and drainage area of 149 km2 as upstream watershed while a mild slope of the riverbed to 0.2% found in a river reach of 20.3 km downstream of this weir, which considered as a gauged basin. However, the major branch streams of the Pua River are ungauged catchments namely: Nam Kwang and Nam Koon with the drainage area of 86 and 35 km2 respectively. These upstream watersheds produce runoff through the 3-streams downstream of Pua weir, Jao weir, and Kang weir, with an averaged annual runoff of 578 million cubic meters. They were analyzed using both statistical data at Pua weir and simulated data resulted from the hydrologic modeling system (HEC–HMS) which applied for the remaining ungauged basins. Since the Kwang and Koon catchments were limited with lack of hydrological data included streamflow and rainfall. Therefore, the mathematical modeling: HEC-HMS with the Snyder-s hydrograph synthesized and transposed methods were applied for those areas using calibrated hydrological parameters from the upstream of Pua weir with continuously daily recorded of streamflow and rainfall data during 2008-2011. The results showed that the simulated daily streamflow and sum up as annual runoff in 2008, 2010, and 2011 were fitted with observed annual runoff at Pua weir using the simple linear regression with the satisfied correlation R2 of 0.64, 062, and 0.59, respectively. The sensitivity of simulation results were come from difficulty using calibrated parameters i.e. lag-time, coefficient of peak flow, initial losses, uniform loss rates, and missing some daily observed data. These calibrated parameters were used to apply for the other 2-ungauged catchments and downstream catchments simulated.
Abstract: The main aim of Supply Chain Management (SCM) is
to produce, distribute, logistics and deliver goods and equipment in
right location, right time, right amount to satisfy costumers, with
minimum time and cost waste. So implementing techniques that
reduce project time and cost, and improve productivity and
performance is very important. Emerging technologies such as the
Radio Frequency Identification (RFID) are now making it possible to
automate supply chains in a real time manner and making them more
efficient than the simple supply chain of the past for tracing and
monitoring goods and products and capturing data on movements of
goods and other events. This paper considers concepts, components
and RFID technology characteristics by concentration of warehouse
and inventories management. Additionally, utilization of RFID in the
role of improving information management in supply chain is
discussed. Finally, the facts of installation and this technology-s
results in direction with warehouse and inventory management and
business development will be presented.
Abstract: In modern telecommunications industry, demand &
supply chain management (DSCM) needs reliable design and
versatile tools to control the material flow. The objective for efficient
DSCM is reducing inventory, lead times and related costs in order to
assure reliable and on-time deliveries from manufacturing units
towards customers. In this paper the multi-rate expert system based
methodology for developing simulation tools that would enable
optimal DSCM for multi region, high volume and high complexity
manufacturing environment was proposed.
Abstract: Perth will run out of available sustainable natural
water resources by 2015 if nothing is done to slow usage rates,
according to a Western Australian study [1]. Alternative water
technology options need to be considered for the long-term
guaranteed supply of water for agricultural, commercial, domestic
and industrial purposes. Seawater is an alternative source of water for
human consumption, because seawater can be desalinated and
supplied in large quantities to a very high quality.
While seawater desalination is a promising option, the technology
requires a large amount of energy which is typically generated from
fossil fuels. The combustion of fossil fuels emits greenhouse gases
(GHG) and, is implicated in climate change. In addition to
environmental emissions from electricity generation for desalination,
greenhouse gases are emitted in the production of chemicals and
membranes for water treatment. Since Australia is a signatory to the
Kyoto Protocol, it is important to quantify greenhouse gas emissions
from desalinated water production.
A life cycle assessment (LCA) has been carried out to determine
the greenhouse gas emissions from the production of 1 gigalitre (GL)
of water from the new plant. In this LCA analysis, a new desalination
plant that will be installed in Bunbury, Western Australia, and known
as Southern Seawater Desalinization Plant (SSDP), was taken as a
case study. The system boundary of the LCA mainly consists of three
stages: seawater extraction, treatment and delivery. The analysis
found that the equivalent of 3,890 tonnes of CO2 could be emitted
from the production of 1 GL of desalinated water. This LCA analysis
has also identified that the reverse osmosis process would cause the
most significant greenhouse emissions as a result of the electricity
used if this is generated from fossil fuels
Abstract: The continuity in the electric supply of the electric installations is becoming one of the main requirements of the electric supply network (generation, transmission, and distribution of the electric energy). The achievement of this requirement depends from one side on the structure of the electric network and on the other side on the avaibility of the reserve source provided to maintain the supply in case of failure of the principal one. The avaibility of supply does not only depends on the reliability parameters of the both sources (principal and reserve) but it also depends on the reliability of the circuit breaker which plays the role of interlocking the reserve source in case of failure of the principal one. In addition, the principal source being under operation, its control can be ideal and sure, however, for the reserve source being in stop, a preventive maintenances which proceed on time intervals (periodicity) and for well defined lengths of time are envisaged, so that this source will always available in case of the principal source failure. The choice of the periodicity of preventive maintenance of the source of reserve influences directly the reliability of the electric feeder system In this work and on the basis of the semi- markovian's processes, the influence of the time of interlocking the reserve source upon the reliability of an industrial electric network is studied and is given the optimal time of interlocking the reserve source in case of failure the principal one, also the influence of the periodicity of the preventive maintenance of the source of reserve is studied and is given the optimal periodicity.
Abstract: The utilization of cheese whey as a fermentation
substrate to produce bio-ethanol is an effort to supply bio-ethanol
demand as a renewable energy. Like other process systems, modeling
is also required for fermentation process design, optimization and
plant operation. This research aims to study the fermentation process
of cheese whey by applying mathematics and fundamental concept in
chemical engineering, and to investigate the characteristic of the
cheese whey fermentation process. Steady state simulation results for
inlet substrate concentration of 50, 100 and 150 g/l, and various
values of hydraulic retention time, showed that the ethanol
productivity maximum values were 0.1091, 0.3163 and 0.5639 g/l.h
respectively. Those values were achieved at hydraulic retention time
of 20 hours, which was the minimum value used in this modeling.
This showed that operating reactor at low hydraulic retention time
was favorable. Model of bio-ethanol production from cheese whey
will enhance the understanding of what really happen in the
fermentation process.
Abstract: The present paper was concerned primarily with the
analysis, simulation of the air flow and thermal patterns in a lecture
room. The paper is devoted to numerically investigate the influence
of location and number of ventilation and air conditioning supply and
extracts openings on air flow properties in a lecture room. The work
focuses on air flow patterns, thermal behaviour in lecture room where
large number of students. The effectiveness of an air flow system is
commonly assessed by the successful removal of sensible and latent
loads from occupants with additional of attaining air pollutant at a
prescribed level to attain the human thermal comfort conditions and
to improve the indoor air quality; this is the main target during the
present paper. The study is carried out using computational fluid
dynamics (CFD) simulation techniques as embedded in the
commercially available CFD code (FLUENT 6.2). The CFD
modelling techniques solved the continuity, momentum and energy
conservation equations in addition to standard k – ε model equations
for turbulence closure.
Throughout the investigations, numerical validation is carried out by
way of comparisons of numerical and experimental results. Good
agreement is found among both predictions.
Abstract: Microcirculation is essential for the proper supply of
oxygen and nutritive substances to the biological tissue and the
removal of waste products of metabolism. The determination of
blood flow in the capillaries is therefore of great interest to clinicians.
A comparison has been carried out using the developed non-invasive,
non-contact and whole field laser speckle contrast imaging (LSCI)
based technique and as well as a commercially available laser
Doppler blood flowmeter (LDF) to evaluate blood flow at the finger
tip and elbow and is presented here. The LSCI technique gives more
quantitative information on the velocity of blood when compared to
the perfusion values obtained using the LDF. Measurement of blood
flow in capillaries can be of great interest to clinicians in the
diagnosis of vascular diseases of the upper extremities.
Abstract: A active inductor in CMOS techonology with a supply voltage of 1.8V is presented. The value of the inductance L can be in the range from 0.12nH to 0.25nH in high frequency(HF). The proposed active inductor is designed in TSMC 0.18-um CMOS technology. The power dissipation of this inductor can retain constant at all operating frequency bands and consume around 20mW from 1.8V power supply. Inductors designed by integrated circuit occupy much smaller area, for this reason,attracted researchers attention for more than decade. In this design we used Advanced Designed System (ADS) for simulating cicuit.
Abstract: Indoor air distribution has great impact on people-s thermal sensation. Therefore, how to remove the indoor excess heat becomes an important issue to create a thermally comfortable indoor environment. To expel the extra indoor heat effectively, this paper used a dynamic CFD approach to study the effect of an air-supply guide vane swinging periodically on the indoor air distribution within a model room. The numerical results revealed that the indoor heat transfer performance caused by the swing guide vane had close relation with the number of vortices developing under the inlet cold jet. At larger swing amplitude, two smaller vortices continued to shed outward under the cold jet and remove the indoor heat load more effectively. As a result, it can be found that the average Nusselt number on the floor increased with the increase of the swing amplitude of the guide vane.
Abstract: The paper proposes a new concept in developing
collaborative design system. The concept framework involves
applying simulation of supply chain management to collaborative
design called – 'SCM–Based Design Tool'. The system is developed
particularly to support design activities and to integrate all facilities
together. The system is aimed to increase design productivity and
creativity. Therefore, designers and customers can collaborate by the
system since conceptual design. JAG: Jewelry Art Generator based
on artificial intelligence techniques is integrated into the system.
Moreover, the proposed system can support users as decision tool
and data propagation. The system covers since raw material supply
until product delivery. Data management and sharing information are
visually supported to designers and customers via user interface. The
system is developed on Web–assisted product development
environment. The prototype system is presented for Thai jewelry
industry as a system prototype demonstration, but applicable for
other industry.
Abstract: An active RC filters with a 880 / 1760 MHz dual bandwidth tuning ability is present for 60 GHz unlicensed band applications. A third order Butterworth low-pass filter utilizes two Cherry-Hooper amplifiers to satisfy the very high bandwidth requirements of an amplifier. The low-pass filter is fabricated in 90nm standard CMOS process. Drawing 6.7 mW from 1.2 V power supply, the low frequency gains of the filter are -2.5 and -4.1 dB, and the output third order intercept points (OIP3) are +2.2 and +1.9 dBm for the single channel and channel bonding conditions, respectively.
Abstract: This paper presents a new true RMS-to-DC converter
circuit based on a square-root-domain squarer/divider. The circuit is
designed by employing up-down translinear loop and using of
MOSFET transistors that operate in strong inversion saturation
region. The converter offer advantages of two-quadrant input current,
low circuit complexity, low supply voltage (1.2V) and immunity
from the body effect. The circuit has been simulated by HSPICE.
The simulation results are seen to conform to the theoretical analysis
and shows benefits of the proposed circuit.
Abstract: Primary and secondary data from the Bauchi abattoir were utilized to determine the relative contributions of different livestock species to meat supply in Bauchi Metropolis. Daily livestock slaughter figures for five months (June – October 2011) indicated that more goats (64.0) were slaughtered than either sheep (47.3) or cattle (41.30) each day (P