Abstract: Battery storage system is emerging as an essential component of hybrid power system based on renewable energy resources such as solar and wind in order to make these sources dispatchable. Accurate modeling of battery storage system is ssential in order to ensure optimal planning of hybrid power systems incorporating battery storage. Majority of the system planning studies involving battery storage assume battery charging efficiency to be constant. However a strong correlation exists between battery charging efficiency and battery state of charge. In this work a Fuzzy logic based model has been presented for determining battery charging efficiency relative to a particular SOC. In order to demonstrate the efficacy of proposed approach, reliability evaluation studies are carried out for a hypothetical autonomous hybrid power system located in Jaisalmer, Rajasthan, India. The impact of considering battery charging efficiency as a function of state of charge is compared against the assumption of fixed battery charging efficiency for three different configurations comprising of wind-storage, solar-storage and wind-solar-storage.
Abstract: A new approach for protection of power transformer is
presented using a time-frequency transform known as Wavelet transform.
Different operating conditions such as inrush, Normal, load,
External fault and internal fault current are sampled and processed
to obtain wavelet coefficients. Different Operating conditions provide
variation in wavelet coefficients. Features like energy and Standard
deviation are calculated using Parsevals theorem. These features
are used as inputs to PNN (Probabilistic neural network) for fault
classification. The proposed algorithm provides more accurate results
even in the presence of noise inputs and accurately identifies inrush
and fault currents. Overall classification accuracy of the proposed
method is found to be 96.45%. Simulation of the fault (with and
without noise) was done using MATLAB AND SIMULINK software
taking 2 cycles of data window (40 m sec) containing 800 samples.
The algorithm was evaluated by using 10 % Gaussian white noise.
Abstract: In this study, a Loop Back Algorithm for component
connected labeling for detecting objects in a digital image is
presented. The approach is using loop back connected component
labeling algorithm that helps the system to distinguish the object
detected according to their label. Deferent than whole window
scanning technique, this technique reduces the searching time for
locating the object by focusing on the suspected object based on
certain features defined. In this study, the approach was also
implemented for a face detection system. Face detection system is
becoming interesting research since there are many devices or
systems that require detecting the face for certain purposes. The input
can be from still image or videos, therefore the sub process of this
system has to be simple, efficient and accurate to give a good result.
Abstract: The impact of OO design on software quality
characteristics such as defect density and rework by mean of
experimental validation. Encapsulation, inheritance, polymorphism,
reusability, Data hiding and message-passing are the major attribute
of an Object Oriented system. In order to evaluate the quality of an
Object oriented system the above said attributes can act as indicators.
The metrics are the well known quantifiable approach to express any
attribute. Hence, in this paper we tried to formulate a framework of
metrics representing the attributes of object oriented system.
Empirical Data is collected from three different projects based on
object oriented paradigms to calculate the metrics.
Abstract: Fractional Fourier Transform is a generalization of the
classical Fourier Transform. The Fractional Fourier span in general
depends on the amplitude and phase functions of the signal and varies
with the transform order. However, with the development of the
Fractional Fourier filter banks, it is advantageous in some cases to
have different transform orders for different filter banks to achieve
better decorrelation of the windowed and overlapped time signal. We
present an expression that is useful for finding the perturbation in the
Fractional Fourier span due to the erroneous transform order and the
possible variation in the window shape and length. The expression is
based on the dependency of the time-Fractional Fourier span
Uncertainty on the amplitude and phase function of the signal. We
also show with the help of the developed expression that the
perturbation of span has a varying degree of sensitivity for varying
degree of transform order and the window coefficients.
Abstract: The frequency contents of the non-stationary
signals vary with time. For proper characterization of such
signals, a smart time-frequency representation is necessary.
Classically, the STFT (short-time Fourier transform) is
employed for this purpose. Its limitation is the fixed timefrequency
resolution. To overcome this drawback an enhanced
STFT version is devised. It is based on the signal driven
sampling scheme, which is named as the cross-level sampling.
It can adapt the sampling frequency and the window function
(length plus shape) by following the input signal local
variations. This adaptation results into the proposed technique
appealing features, which are the adaptive time-frequency
resolution and the computational efficiency.
Abstract: In power systems, protective relays must filter their
inputs to remove undesirable quantities and retain signal quantities of
interest. This job must be performed accurate and fast. A new
method for filtering the undesirable components such as DC and
harmonic components associated with the fundamental system
signals. The method is s based on a dynamic filtering algorithm. The
filtering algorithm has many advantages over some other classical
methods. It can be used as dynamic on-line filter without the need of
parameters readjusting as in the case of classic filters. The proposed
filter is tested using different signals. Effects of number of samples
and sampling window size are discussed. Results obtained are
presented and discussed to show the algorithm capabilities.
Abstract: Because support interference corrections are not properly
understood, engineers mostly rely on expensive dummy measurements
or CFD calculations. This paper presents a method based on uncorrected wind tunnel measurements and fast calculation techniques
(it is a hybrid method) to calculate wall interference, support interference and residual interference (when e.g. a support member
closely approaches the wind tunnel walls) for any type of wind tunnel and support configuration. The method provides with a simple formula
for the calculation of the interference gradient. This gradient is
based on the uncorrected measurements and a successive calculation
of the slopes of the interference-free aerodynamic coefficients. For the latter purpose a new vortex-lattice routine is developed that corrects
the slopes for viscous effects. A test case of a measurement on a wing proves the value of this hybrid method as trends and orders of
magnitudes of the interference are correctly determined.
Abstract: The paper presents a modelling methodology for
small scale multi-source renewable energy systems. Using historical
site-specific weather data, the relationships of cost, availability and
energy form are visualised as a function of the sizing of photovoltaic
arrays, wind turbines, and battery capacity. The specific dependency
of each site on its own particular weather patterns show that unique
solutions exist for each site. It is shown that in certain cases the
capital component cost can be halved if the desired theoretical
demand availability is reduced from 100% to 99%.
Abstract: The design of high-rise building is more often dictated
by its serviceability rather than strength. Structural Engineers are
always striving to overcome challenge of controlling lateral
deflection and storey drifts as well as self weight of structure
imposed on foundation.
One of the most effective techniques is the use of outrigger and
belt truss system in Composite structures that can astutely solve the
above two issues in High-rise constructions.
This paper investigates deflection control by effective utilisation
of belt truss and outrigger system on a 60-storey composite building
subjected to wind loads. A three dimensional Finite Element Analysis
is performed with one, two and three outrigger levels. The reductions
in lateral deflection are 34%, 42% and 51% respectively as compared
to a model without any outrigger system. There is an appreciable
decline in the storey drifts with the introduction of these stiffer
arrangements.
Abstract: In hypersonic environments, the aerothermal effect
makes it difficult for the optical side windows of optical guided
missiles to withstand high heat. This produces cracking or breaking,
resulting in an inability to function. This study used computational
fluid mechanics to investigate the external cooling jet conditions of
optical side windows. The turbulent models k-ε and k-ω were
simulated. To be in better accord with actual aerothermal
environments, a thermal radiation model was added to examine
suitable amounts of external coolants and the optical window
problems of aero-thermodynamics. The simulation results indicate that
when there are no external cooling jets, because airflow on the optical
window and the tail groove produce vortices, the temperatures in these
two locations reach a peak of approximately 1600 K. When the
external cooling jets worked at 0.15 kg/s, the surface temperature of
the optical windows dropped to approximately 280 K. When adding
thermal radiation conditions, because heat flux dissipation was faster,
the surface temperature of the optical windows fell from 280 K to
approximately 260 K. The difference in influence of the different
turbulence models k-ε and k-ω on optical window surface temperature
was not significant.
Abstract: The effect of the blade tip geometry of a high pressure
gas turbine is studied experimentally and computationally for high
speed leakage flows. For this purpose two simplified models are
constructed, one models a flat tip of the blade and the second models
a cavity tip of the blade. Experimental results are obtained from a
transonic wind tunnel to show the static pressure distribution along
the tip wall and provide flow visualization. RANS computations
were carried to provide further insight into the mean flow behavior
and to calculate the discharge coefficient which is a measure of the
flow leaking over the tip. It is shown that in both geometries of tip
the flow separates over the tip to form a separation bubble. The
bubble is higher for the cavity tip while a complete shock wave
system of oblique waves ending with a normal wave can be seen for
the flat tip. The discharge coefficient for the flat tip shows less
dependence on the pressure ratio over the blade tip than the cavity
tip. However, the discharge coefficient for the cavity tip is lower than
that of the flat tip, showing a better ability to reduce the leakage flow
and thus increase the turbine efficiency.
Abstract: Atmospheric stability plays the most important role in
the transport and dispersion of air pollutants. Different methods are
used for stability determination with varying degrees of complexity.
Most of these methods are based on the relative magnitude of
convective and mechanical turbulence in atmospheric motions.
Richardson number, Monin-Obukhov length, Pasquill-Gifford
stability classification and Pasquill–Turner stability classification, are
the most common parameters and methods. The Pasquill–Turner
Method (PTM), which is employed in this study, makes use of
observations of wind speed, insolation and the time of day to classify
atmospheric stability with distinguishable indices. In this study, a
model is presented to determination of atmospheric stability
conditions using PTM. As a case study, meteorological data of
Mehrabad station in Tehran from 2000 to 2005 is applied to model.
Here, three different categories are considered to deduce the pattern
of stability conditions. First, the total pattern of stability classification
is obtained and results show that atmosphere is 38.77%, 27.26%,
33.97%, at stable, neutral and unstable condition, respectively. It is
also observed that days are mostly unstable (66.50%) while nights are
mostly stable (72.55%). Second, monthly and seasonal patterns are
derived and results indicate that relative frequency of stable
conditions decrease during January to June and increase during June
to December, while results for unstable conditions are exactly in
opposite manner. Autumn is the most stable season with relative
frequency of 50.69% for stable condition, whilst, it is 42.79%,
34.38% and 27.08% for winter, summer and spring, respectively.
Hourly stability pattern is the third category that points out that
unstable condition is dominant from approximately 03-15 GTM and
04-12 GTM for warm and cold seasons, respectively. Finally,
correlation between atmospheric stability and CO concentration is
achieved.
Abstract: This article presents a performance comparison of an
interior mounted permanent magnet synchronous generator (IPMSG)
with a synchronous reluctance generator (SynRG) with the same size
for a wind application. It is found that using the same geometrical
dimensions, a SynRG can convert 74 % of the power that an IPMSG
can convert, while it has 80% of the IPMSG weight. Moreover it is
found that the efficieny for the IMPSG is 99% at rated power
compared to 98.7% for the SynRG.
Abstract: The paper investigates the feasibility of constructing a software multi-agent based monitoring and classification system and utilizing it to provide an automated and accurate classification of end users developing applications in the spreadsheet domain. The agents function autonomously to provide continuous and periodic monitoring of excels spreadsheet workbooks. Resulting in, the development of the MultiAgent classification System (MACS) that is in compliance with the specifications of the Foundation for Intelligent Physical Agents (FIPA). However, different technologies have been brought together to build MACS. The strength of the system is the integration of the agent technology with the FIPA specifications together with other technologies that are Windows Communication Foundation (WCF) services, Service Oriented Architecture (SOA), and Oracle Data Mining (ODM). The Microsoft's .NET widows service based agents were utilized to develop the monitoring agents of MACS, the .NET WCF services together with SOA approach allowed the distribution and communication between agents over the WWW that is in order to satisfy the monitoring and classification of the multiple developer aspect. ODM was used to automate the classification phase of MACS.
Abstract: The present study aims to evaluating the effect of
rotor solidity - in terms of chord length for a given rotor diameter - on
the performances of a small vertical axis Darrieus wind turbine. The
proposed work focuses on both power production and rotor power
coefficient, considering also the structural constraints deriving from
the centrifugal forces due to rotor angular velocity. Also the
smoothness of the resulting power curves have been investigated, in
order to evaluate the controllability of the corresponding rotor
architectures.
Abstract: This paper presents a digital engineering library – the
Digital Mechanism and Gear Library, DMG-Lib – providing a multimedia collection of e-books, pictures, videos and animations in the domain of mechanisms and machines. The specific characteristic
about DMG-Lib is the enrichment and cross-linking of the different
sources. DMG-Lib e-books not only present pages as pixel images
but also selected figures augmented with interactive animations. The
presentation of animations in e-books increases the clearness of the
information.
To present the multimedia e-books and make them available in the
DMG-Lib internet portal a special e-book reader called StreamBook
was developed for optimal presentation of digitized books and to
enable reading the e-books as well as working efficiently and individually with the enriched information. The objective is to support different user tasks ranging from information retrieval to
development and design of mechanisms.
Abstract: A kind of singularly perturbed boundary value problems is under consideration. In order to obtain its approximation, simple upwind difference discretization is applied. We use a moving mesh iterative algorithm based on equi-distributing of the arc-length function of the current computed piecewise linear solution. First, a maximum norm a posteriori error estimate on an arbitrary mesh is derived using a different method from the one carried out by Chen [Advances in Computational Mathematics, 24(1-4) (2006), 197-212.]. Then, basing on the properties of discrete Green-s function and the presented posteriori error estimate, we theoretically prove that the discrete solutions computed by the algorithm are first-order uniformly convergent with respect to the perturbation parameter ε.
Abstract: Most buildings have been using anchor bolts
commonly for installing outdoor advertising structures. Anchor bolts
of common carbon steel are widely used and often installed
indiscriminately by inadequate installation standards. In the area
where strong winds frequently blow, falling accidents of outdoor
advertising structures can occur and cause a serious disaster, which is
very dangerous and to be prevented. In this regard, the development of
high-performance anchor bolts is urgently required. In the present
study, 25Cr-8Ni-1.5Si-1Mn-0.4C alloy was produced by traditional
vacuum induction melting (VIM) for the application of anchor bolt.
The alloy composition is revealed as a duplex microstructure from
thermodynamic phase analysis by FactSage® and confirmed by
metallographic experiment. Addition of Nitrogen to the alloy was
found to reduce the ferritic phase domain and significantly increase the
hardness and the tensile strength. Microstructure observation revealed
mixed structure of austenite and ferrite with fine carbide distributed
along the grain and phase boundaries.
Abstract: Stream Control Transmission Protocol (SCTP) has been
proposed to provide reliable transport of real-time communications.
Due to its attractive features, such as multi-streaming and multihoming,
the SCTP is often expected to be an alternative protocol
for TCP and UDP. In the original SCTP standard, the secondary path
is mainly regarded as a redundancy. Recently, most of researches
have focused on extending the SCTP to enable a host to send its
packets to a destination over multiple paths simultaneously. In order
to transfer packets concurrently over the multiple paths, the SCTP
should be well designed to avoid unnecessary fast retransmission
and the mis-estimation of congestion window size through the paths.
Therefore, we propose an Enhanced Cooperative ACK SCTP (ECASCTP)
to improve the path recovery efficiency of multi-homed host
which is under concurrent multiple transfer mode. We evaluated the
performance of our proposed scheme using ns-2 simulation in terms
of cwnd variation, path recovery time, and goodput. Our scheme
provides better performance in lossy and path asymmetric networks.