Abstract: Optical biosensors have become a powerful detection
and analysis tool for wide-ranging applications in biomedical research,
pharmaceuticals and environmental monitoring. This study carried out
the computational fluid dynamics (CFD)-based simulations to explore
the dispersion phenomenon in the micro channel of an optical
biosensor. The predicted time sequences of concentration contours
were utilized to better understand the dispersion development occurred
in different geometric shapes of micro channels. The simulation results
showed the surface concentrations at the sensing probe (with the best
performance of a grating coupler) in respect of time to appraise the
dispersion effect and therefore identify the design configurations
resulting in minimum dispersion.
Abstract: Any variation in environmental characteristics of
geomorphosites would lead to destabilisation of their geotouristic
values all around the planet. The Urmia lake, with an area of
approximately 5,500 km2 and a catchment area of 51,876 km2, and to
which various reasons over time, especially in the last fifty years
have seen a sharp decline and have decreased by about 93 % in two
recent decades. These variations are not only driving significant
changes in the morphology and ecology of the present lake
landscape, but at the same time are shaping newly formed
morphologies, which vanished some valuable geomorphosites or
develop into smaller geomorphosites with significant value from a
scientific and cultural point of view. This paper analyses and
discusses features and evolution in several representative coastal and
island geomorphosites. For this purpose, a total of 23 geomorphosites
were studied in two data series (1963 and 2015) and the respective
data were compared and analysed. The results showed, the total loss
in geomorphosites area in a half century amounted to a loss of more
than 90% of the valuable geomorphosites. Moreover, the comparison
between the mean yearly value of coastal area lost over the entire
period and the yearly average calculated for the shorter period (1998-
2014) clearly indicates a pattern of acceleration. This acceleration in
the rate of reduction in lake area was seen in most of the southern
half of the lake. In the region as well, the general water-level falling
is not only causing the loss of a significant water resource, which is
followed by major impact on regional ecosystems, but is also driving
the most marked recent (last century) changes in the geotouristic
landscapes. In fact, the disappearance of geomorphosites means the
loss of tourism phenomenon. In this context attention must be paid to
the question of conservation. The action needed to safeguard
geomorphosites includes: 1) Preventive action, 2) Corrective action,
and 3) Sharing knowledge.
Abstract: Electrodeposition is a simple and economic technique
for precision coating of different shaped substrates with pure metal,
alloy or composite films. Dc electrodeposition was used to produce
Cr, Co-Cr and Co-Cr/TiO2 nano-composite coatings from Cr(III)
based electrolytes onto 316L SS substrates. The effects of TiO2 nanoparticles
concentration on co-deposition of these particles along with
Cr content and microhardness of the coatings were investigated.
Morphology of the Cr, Co-Cr and Co-Cr/TiO2 coatings besides their
tribological behavior were studied. The results showed that increment
of TiO2 nanoparticles concentration from 0 to 30 g L-1 in the bath
increased their co-deposition and Cr content of the coatings from 0 to
3.5 wt.% and from 23.7 to 31.2 wt.%, respectively. Microhardness of
Cr coating was about 920 Hv which was higher than Co-Cr and even
Co-Cr/TiO2 films. Microhardness of Co-Cr and Co-Cr/TiO2 coatings
were improved by increasing their Cr and TiO2 content. All the
coatings had nodular morphology and contained microcracks.
Nodules sizes and the number of microcracks in the alloy and
composite coatings were lower than the Cr film. Wear results
revealed that the Co-Cr/TiO2 coating had the lowest wear loss
between all the samples, while the Cr film had the worst wear
resistance.
Abstract: This article is to introduce the meaning and form of
social quality moving process as indicated by members of two suburb
communities with different social and cultural contexts. The form of
social quality moving process is very significant for the community
and social development, because it will make the people living
together with sustainable happiness.
This is a qualitative study involving 30 key-informants from two
suburb communities. Data were collected though key-informant
interviews, and analyzed using logical content description and
descriptive statistics.
This research found that on the social quality component, the
people in both communities stressed the procedure for social qualitymaking.
This includes the generousness, sharing and assisting among
people in the communities. These practices helped making people to
live together with sustainable happiness. Living as a family or appear
to be a family is the major social characteristic of these two
communities.
This research also found that form of social quality’s moving
process of both communities stress relation of human and nature;
“nature overpower humans” paradigm and influence of religious
doctrine that emphasizes relations among humans. Both criteria make
the form of social’s moving process simple, adaptive to nature and
caring for opinion sharing and understanding among each other
before action. This form of social quality’s moving process is
composed of 4 steps; (1) awareness building, (2) motivation to
change, (3) participation from every party which is concerned (4)
self-reliance.
Abstract: Auditory hallucinations among the most invalidating
and distressing experiences reported by patients diagnosed with
schizophrenia, leading to feelings of powerlessness and helplessness
towards their illness. In more severe cases, these auditory
hallucinations can take the form of commanding voices, which are
often related to high suicidality rates in these patients. Several
authors propose that the meanings attributed to the hallucinatory
experience, rather than characteristics like form and content, can be
determinant in patients’ reactions to hallucinatory activity,
particularly in the case of voice-hearing experiences. In this study, 48
patients diagnosed with paranoid schizophrenia presenting auditory
hallucinations were studied. Multiple regression analyses were
computed to study the influence of several developmental aspects,
such as family and social dynamics, bullying, depression, and sociocognitive
variables on the auditory hallucinations, on patients’
attributions and relationships with their voices, and on the resulting
invalidation of hallucinatory experience. Overall, results showed how
relationships with voices can mirror several aspects of interpersonal
relationship with others, and how self-schemas, depression and actual
social relationships help shaping the voice-hearing experience. Early
experiences of victimization and submission help predict the
attributions of omnipotence of the voices, and increased hostility
from parents seems to increase the malevolence of the voices,
suggesting that socio-cognitive factors can significantly contribute to
the etiology and maintenance of auditory hallucinations. The
understanding of the characteristics of auditory hallucinations and the
relationships patients established with their voices can allow the
development of more promising therapeutic interventions that can be
more effective in decreasing invalidation caused by this devastating
mental illness.
Abstract: Plasmin plays an important role in the human
circulatory system owing to its catalytic ability of fibrinolysis. The
immediate injection of plasmin in patients of strokes has intrigued
many scientists to design vectors that can transport plasmin to the
desired location in human body. Here we predict the structure of
human plasmin and investigate the interaction of plasmin with the
gold-nanoparticle.
Because the crystal structure of plasminogen has been solved, we
deleted N-terminal domain (Pan-apple domain) of plasminogen and
generate a mimic of the active form of this enzyme (plasmin). We
conducted a simulated annealing process on plasmin and discovered a
very large conformation occurs. Kringle domains 1, 4 and 5 had been
observed to leave its original location relative to the main body of the
enzyme and the original doughnut shape of this enzyme has been
transformed to a V-shaped by opening its two arms. This observation
of conformational change is consistent with the experimental results of
neutron scattering and centrifugation.
We subsequently docked the plasmin on the simulated gold surface
to predict their interaction. The V-shaped plasmin could utilize its
Kringle domain and catalytic domain to contact the gold surface.
Our findings not only reveal the flexibility of plasmin structure but
also provide a guide for the design of a plasmin-gold nanoparticle.
Abstract: This paper reports a novel actuating design that uses
the shear deformation of a piezoelectric actuator to deflect a
bulge-diaphragm for driving an array microdroplet ejector. In essence,
we employed a circular-shaped actuator poled radial direction with
remnant polarization normal to the actuating electric field for inducing
the piezoelectric shear effect. The array microdroplet ejector consists
of a shear type piezoelectric actuator, a vibration plate, two chamber
plates, two channel plates and a nozzle plate. The vibration, chamber
and nozzle plate components are fabricated using nickel
electroforming technology, whereas the channel plate is fabricated by
etching of stainless steel. The diaphragm displacement was measured
by the laser two-dimensional scanning vibrometer. The ejected
droplets of the microejector were also observed via an optic
visualization system.
Abstract: This paper is aimed at proposing a rhombus shaped
wearable fractal antenna for wireless communication systems. The
geometrical descriptors of the antenna have been obtained using
bacterial foraging optimization (BFO) for wide band operation. The
method of moment based IE3D software has been used to simulate
the antenna and observed that miniaturization of 13.08% has been
achieved without degrading the resonating properties of the proposed
antenna. An analysis with different substrates has also been done in
order to evaluate the effectiveness of electrical permittivity on the
presented structure. The proposed antenna has low profile, light
weight and has successfully demonstrated wideband and multiband
characteristics for wearable electronic applications.
Abstract: In order to produce lead free piezoceramics with
optimum piezoelectric and dielectric properties, KNN modified with
Li+ (as an A site dopant) and Sb5+ (as a B site dopant)
(K0.49Na0.49Li0.02) (Nb0.96Sb0.04) O3 (referred as KNLNS in this paper)
have been synthesized using solid state reaction method and
conventional sintering technique. The ceramics were sintered in the
narrow range of 1050°C-1090°C for 2-3 h to get precise information
about sintering parameters. Detailed study of dependence of
microstructural, dielectric and piezoelectric properties on sintering
conditions was then carried out. The study suggests that the volatility
of the highly hygroscopic KNN ceramics is not only sensitive to
sintering temperatures but also to sintering durations. By merely
reducing the sintering duration for a given sintering temperature we
saw an increase in the density of the samples which was supported by
the increase in dielectric constants of the ceramics. And since density
directly or indirectly affects almost all the associated properties, other
dielectric and piezoelectric properties were also enhanced as we
approached towards the most suitable sintering temperature and
duration combination. The detailed results are reported in this paper.
Abstract: In this paper we propose a novel methodology for
extracting a road network and its nodes from satellite images of
Algeria country.
This developed technique is a progress of our previous research
works. It is founded on the information theory and the mathematical
morphology; the information theory and the mathematical
morphology are combined together to extract and link the road
segments to form a road network and its nodes.
We therefore have to define objects as sets of pixels and to study
the shape of these objects and the relations that exist between them.
In this approach, geometric and radiometric features of roads are
integrated by a cost function and a set of selected points of a crossing
road. Its performances were tested on satellite images of Algeria
country.
Abstract: Heat transfer of leaves is a crucial factor in optimal
operation of metabolic functions in plants. In order to quantify this
phenomenon in different leaves and investigate the influence of leaf
shape on heat transfer, natural convection for pine, orange and olive
leaves was simulated as representatives of different groups of leaf
shapes. CFD techniques were used in this simulation with the
purpose to calculate heat transfer of leaves in similar environmental
conditions. The problem was simulated for steady state and threedimensional
conditions. From obtained results, it was concluded that
heat fluxes of all three different leaves are almost identical, however,
total rate of heat transfer have highest and lowest values for orange
leaves, and pine leaves, respectively.
Abstract: One of the main challenges in using the Discrete
Element Method (DEM) is to specify the correct input parameter
values. In general, the models are sensitive to the input parameter
values and accurate results can only be achieved if the correct values
are specified. For the linear contact model, micro-parameters such as
the particle density, stiffness, coefficient of friction, as well as the
particle size and shape distributions are required. There is a need for
a procedure to accurately calibrate these parameters before any
attempt can be made to accurately model a complete bulk materials
handling system. Since DEM is often used to model applications in
the mining and quarrying industries, a calibration procedure was
developed for materials that consist of relatively large (up to 40 mm
in size) particles. A coarse crushed aggregate was used as the test
material. Using a specially designed large shear box with a diameter
of 590 mm, the confined Young’s modulus (bulk stiffness) and
internal friction angle of the material were measured by means of the
confined compression test and the direct shear test respectively. DEM
models of the experimental setup were developed and the input
parameter values were varied iteratively until a close correlation
between the experimental and numerical results was achieved. The
calibration process was validated by modelling the pull-out of an
anchor from a bed of material. The model results compared well with
experimental measurement.
Abstract: Due to rapid pressured of population growth, city has
started to lose its old tradition. City becomes congested with
uncomfortably living. Urban renewal refers orderly development of
settlements as well as land redevelopment. For this paper Chittagong
city has been selected as study area. It had a great tradition but it has
been losing its concord. Land use pattern of this place is also
haphazard due to lack of planning intervention. Renewal plan is
needed to ascertain suitable redevelopment and to recommend on
preservation of city heritage structure. The goal of this study is to
prepare a renewal plan using local planning approach. Social impact
methods have been used to achieve this goal. Both primary and
secondary data are used to achieve the goal. This study may find out
a complete solution for healthy living in old Part of city. This study
will help to preserve its tradition and makes urban lives more livable.
Abstract: Objects are usually horizontally sliced when printed by 3D printers. Therefore, if an object to be printed, such as a collection of fibers, originally has natural direction in shape, the printed direction contradicts with the natural direction. By using proper tools, such as field-oriented 3D paint software, field-oriented solid modelers, field-based tool-path generation software, and non-horizontal FDM 3D printers, the natural direction can be modeled and objects can be printed in a direction that is consistent with the natural direction. This consistence results in embodiment of momentum or force in expressions of the printed object. To achieve this goal, several design and manufacturing problems, but not all, have been solved. An application of this method is (Japanese) 3D calligraphy.
Abstract: Image compression based on fractal coding is a lossy
compression method and normally used for gray level images range
and domain blocks in rectangular shape. Fractal based digital image
compression technique provide a large compression ratio and in this
paper, it is proposed using YUV colour space and the fractal theory
which is based on iterated transformation. Fractal geometry is mainly
applied in the current study towards colour image compression
coding. These colour images possesses correlations among the colour
components and hence high compression ratio can be achieved by
exploiting all these redundancies. The proposed method utilises the
self-similarity in the colour image as well as the cross-correlations
between them. Experimental results show that the greater
compression ratio can be achieved with large domain blocks but more
trade off in image quality is good to acceptable at less than 1 bit per
pixel.
Abstract: We proposed a Hyperbolic Gompertz Growth Model
(HGGM), which was developed by introducing a shape parameter
(allometric). This was achieved by convoluting hyperbolic sine
function on the intrinsic rate of growth in the classical gompertz
growth equation. The resulting integral solution obtained
deterministically was reprogrammed into a statistical model and used
in modeling the height and diameter of Pines (Pinus caribaea). Its
ability in model prediction was compared with the classical gompertz
growth model, an approach which mimicked the natural variability of
height/diameter increment with respect to age and therefore provides
a more realistic height/diameter predictions using goodness of fit
tests and model selection criteria. The Kolmogorov Smirnov test and
Shapiro-Wilk test was also used to test the compliance of the error
term to normality assumptions while the independence of the error
term was confirmed using the runs test. The mean function of top
height/Dbh over age using the two models under study predicted
closely the observed values of top height/Dbh in the hyperbolic
gompertz growth models better than the source model (classical
gompertz growth model) while the results of R2, Adj. R2, MSE and
AIC confirmed the predictive power of the Hyperbolic Gompertz
growth models over its source model.
Abstract: An Australian manufacturer has fabricated an
innovative GFRP sandwich panel made from E-glass fiber skin and a
modified phenolic core for structural applications. Debonding, which
refers to separation of skin from the core material in composite
sandwiches, is one of the most common types of damage in
composites. The presence of debonding is of great concern because it
not only severely affects the stiffness but also modifies the dynamic
behaviour of the structure. Generally it is seen that the majority of
research carried out has been concerned about the delamination of
laminated structures whereas skin-core debonding has received
relatively minor attention. Furthermore it is observed that research
done on composite slabs having multiple skin-core debonding is very
limited. To address this gap, a comprehensive research investigating
dynamic behaviour of composite panels with single and multiple
debonding is presented. The study uses finite-element modelling and
analyses for investigating the influence of debonding on free
vibration behaviour of single and multilayer composite sandwich
panels. A broad parametric investigation has been carried out by
varying debonding locations, debonding sizes and support conditions
of the panels in view of both single and multiple debonding.
Numerical models were developed with Strand7 finite element
package by innovatively selecting the suitable elements to diligently
represent their actual behavior. Three-dimensional finite element
models were employed to simulate the physically real situation as
close as possible, with the use of an experimentally and numerically
validated finite element model. Comparative results and conclusions
based on the analyses are presented. For similar extents and locations
of debonding, the effect of debonding on natural frequencies appears
greatly dependent on the end conditions of the panel, giving greater
decrease in natural frequency when the panels are more restrained.
Some modes are more sensitive to debonding and this sensitivity
seems to be related to their vibration mode shapes. The fundamental
mode seems generally the least sensitive mode to debonding with
respect to the variation in free vibration characteristics. The results
indicate the effectiveness of the developed three dimensional finite
element models in assessing debonding damage in composite
sandwich panels.
Abstract: This paper is focused on the CFD simulation of the radiaxial pump (i.e. mixed flow pump) with the aim to detect the reasons of Y-Q characteristic instability. The main reasons of pressure pulsations were detected by means of the analysis of velocity and pressure fields within the pump combined with the theoretical approach. Consequently, the modifications of spiral case and pump suction area were made based on the knowledge of flow conditions and the shape of dissipation function. The primary design of pump geometry was created as the base model serving for the comparison of individual modification influences. The basic experimental data are available for this geometry. This approach replaced the more complicated and with respect to convergence of all computational tasks more difficult calculation for the compressible liquid flow. The modification of primary pump consisted in inserting the three fins types. Subsequently, the evaluation of pressure pulsations, specific energy curves and visualization of velocity fields were chosen as the criterion for successful design.
Abstract: The article deals with the tool in Matlab GUI form
that is designed to analyse a mechatronic system sensitivity and
tolerance. In the analysed mechatronic system, a torque is transferred
from the drive to the load through a coupling containing flexible
elements. Different methods of control system design are used. The
classic form of the feedback control is proposed using Naslin method,
modulus optimum criterion and inverse dynamics method. The
cascade form of the control is proposed based on combination of
modulus optimum criterion and symmetric optimum criterion. The
sensitivity is analysed on the basis of absolute and relative sensitivity
of system function to the change of chosen parameter value of the
mechatronic system, as well as the control subsystem. The tolerance
is analysed in the form of determining the range of allowed relative
changes of selected system parameters in the field of system stability.
The tool allows to analyse an influence of torsion stiffness, torsion
damping, inertia moments of the motor and the load and controller(s)
parameters. The sensitivity and tolerance are monitored in terms of
the impact of parameter change on the response in the form of system
step response and system frequency-response logarithmic
characteristics. The Symbolic Math Toolbox for expression of the
final shape of analysed system functions was used. The sensitivity
and tolerance are graphically represented as 2D graph of sensitivity
or tolerance of the system function and 3D/2D static/interactive graph
of step/frequency response.
Abstract: Cesium iodide (CsI) melt was injected into anodic aluminum oxide (AAO) template and was solidified to CsI column. The controllable AAO channel size (10~500 nm) can makes CsI column size from 10 to 500 nm in diameter. In order to have a shorter light irradiate from each singe CsI column top to bottom the AAO template was coated a TiO2 nano-film. The TiO2 film acts a refraction film and makes X-ray has a shorter irradiation path in the CsI crystal making a stronger the photo-electron signal. When the incidence light irradiate from air (R=1.0) to CsI’s first surface (R=1.84) the first refraction happen, the first refraction continue into TiO2 film (R=2.88) and produces the low angle of the second refraction. Then the second refraction continue into AAO wall (R=1.78) and produces the third refraction after refractions between CsI and AAO wall (R=1.78) produce the fourth refraction. The incidence light through TiO2 filmand the first surface of CsI then arrive to the second surface of CsI. Therefore, the TiO2 film can has shorter refraction path of incidence light and increase the photo-electron conversion efficiency.