Abstract: A new approach has been used for optimized design of multipliers based upon the concepts of Vedic mathematics. The design has been targeted to state-of-the art field-programmable gate arrays (FPGAs). The multiplier generates partial products using Vedic mathematics method by employing basic 4x4 multipliers designed by exploiting 6-input LUTs and multiplexers in the same slices resulting in drastic reduction in area. The multiplier is realized on Xilinx FPGAs using devices Virtex-5 and Virtex-6.Carry Chain Adder was employed to obtain final products. The performance of the proposed multiplier was examined and compared to well-known multipliers such as Booth, Carry Save, Carry ripple, and array multipliers. It is demonstrated that the proposed multiplier is superior in terms of speed as well as power consumption.
Abstract: An artificial neural network (ANN) approach was used to model the energy consumption of wheat production. This study was conducted over 35,300 hectares of irrigated and dry land wheat fields in Canterbury in the 2007-2008 harvest year.1 In this study several direct and indirect factors have been used to create an artificial neural networks model to predict energy use in wheat production. The final model can predict energy consumption by using farm condition (size of wheat area and number paddocks), farmers- social properties (education), and energy inputs (N and P use, fungicide consumption, seed consumption, and irrigation frequency), it can also predict energy use in Canterbury wheat farms with error margin of ±7% (± 1600 MJ/ha).
Abstract: This paper presents the 20-GHz fractional PLL (Phase
Locked Loop) circuit for the next generation Wi-Fi by using 90 nm
TSMC process. The newly suggested millimeter wave 16/17
pre-scalar is designed and verified by measurement to make the
fractional PLL having a low quantization noise. The operational
bandwidth of the 60 GHz system is 15 % of the carrier frequency
which requires large value of Kv (VCO control gain) resulting in
degradation of phase noise. To solve this problem, this paper adopts
AFC (Automatic Frequency Controller) controlled 4-bit millimeter
wave VCO with small value of Kv. Also constant Kv is implemented
using 4-bit varactor bank. The measured operational bandwidth is 18.2
~ 23.2 GHz which is 25 % of the carrier frequency. The phase noise of
-58 and -96.2 dBc/Hz at 100 KHz and 1 MHz offset is measured
respectively. The total power consumption of the PLL is only 30 mW.
Abstract: In this paper, we present a cost-effective wireless
distributed load shedding system for non-emergency scenarios. In
power transformer locations where SCADA system cannot be used,
the proposed solution provides a reasonable alternative that combines
the use of microcontrollers and existing GSM infrastructure to send
early warning SMS messages to users advising them to proactively
reduce their power consumption before system capacity is reached
and systematic power shutdown takes place.
A novel communication protocol and message set have been
devised to handle the messaging between the transformer sites, where
the microcontrollers are located and where the measurements take
place, and the central processing site where the database server is
hosted. Moreover, the system sends warning messages to the endusers
mobile devices that are used as communication terminals. The
system has been implemented and tested via different experimental
results.
Abstract: This paper presents a new method for read out of the piezoresistive accelerometer sensors. The circuit works based on Instrumentation amplifier and it is useful for reducing offset In Wheatstone Bridge. The obtained gain is 645 with 1μv/°c Equivalent drift and 1.58mw power consumption. A Schmitt trigger and multiplexer circuit control output node. a high speed counter is designed in this work .the proposed circuit is designed and simulated In 0.18μm CMOS technology with 1.8v power supply.
Abstract: The “conveyor belt" as a product represents a
complex high performance component with a wide range of different
applications. Further development of these highly complex
components demands an integration of new technologies and new
enhanced materials. In this context nanostructured fillers appear to
have a more promising effect on the performance of the conveyor
belt composite than conventional micro-scaled fillers.
Within the project “DotTrans" nanostructured fillers, for example
silicon dioxide, are used to optimize performance parameters of
conveyor belt systems. The objective of the project includes
operating parameters like energy consumption or friction
characteristics as well as adaptive parameters like cut or wear
resistance.
Abstract: Careful design and selection of daylighting systems can greatly help in reducing not only artificial lighting use, but also decrease cooling energy consumption and, therefore, potential for downsizing air-conditioning systems. This paper aims to evaluate the energy performance of two types of top-light daylighting systems due to the integration of daylight together with artificial lighting in an existing examinaton hall in University Kebangsaan Malaysia, based on a hot and humid climate. Computer simulation models have been created for building case study (base case) and the two types of toplight daylighting designs for building energy performance evaluation using the VisualDOE 4.0 building energy simulation program. The finding revealed that daylighting through top-light systems is a very beneficial design strategy in reducing annual lighting energy consumption and the overall total annual energy consumption.
Abstract: In this paper, the periodic surveillance scheme has
been proposed for any convex region using mobile wireless sensor
nodes. A sensor network typically consists of fixed number of
sensor nodes which report the measurements of sensed data such as
temperature, pressure, humidity, etc., of its immediate proximity
(the area within its sensing range). For the purpose of sensing an
area of interest, there are adequate number of fixed sensor
nodes required to cover the entire region of interest. It implies
that the number of fixed sensor nodes required to cover a given
area will depend on the sensing range of the sensor as well as
deployment strategies employed. It is assumed that the sensors to
be mobile within the region of surveillance, can be mounted on
moving bodies like robots or vehicle. Therefore, in our
scheme, the surveillance time period determines the number of
sensor nodes required to be deployed in the region of interest.
The proposed scheme comprises of three algorithms namely:
Hexagonalization, Clustering, and Scheduling, The first algorithm
partitions the coverage area into fixed sized hexagons that
approximate the sensing range (cell) of individual sensor node.
The clustering algorithm groups the cells into clusters, each of
which will be covered by a single sensor node. The later
determines a schedule for each sensor to serve its respective cluster.
Each sensor node traverses all the cells belonging to the cluster
assigned to it by oscillating between the first and the last cell for
the duration of its life time. Simulation results show that our
scheme provides full coverage within a given period of time using
few sensors with minimum movement, less power consumption,
and relatively less infrastructure cost.
Abstract: Mobile ad hoc network is a collection of mobile
nodes communicating through wireless channels without any existing
network infrastructure or centralized administration. Because of the
limited transmission range of wireless network interfaces, multiple
"hops" may be needed to exchange data across the network. In order
to facilitate communication within the network, a routing protocol is
used to discover routes between nodes. The primary goal of such an
ad hoc network routing protocol is correct and efficient route
establishment between a pair of nodes so that messages may be
delivered in a timely manner. Route construction should be done
with a minimum of overhead and bandwidth consumption. This paper
examines two routing protocols for mobile ad hoc networks– the
Destination Sequenced Distance Vector (DSDV), the table- driven
protocol and the Ad hoc On- Demand Distance Vector routing
(AODV), an On –Demand protocol and evaluates both protocols
based on packet delivery fraction, normalized routing load, average
delay and throughput while varying number of nodes, speed and
pause time.
Abstract: In this paper a comprehensive model of a fossil fueled
power plant (FFPP) is developed in order to evaluate the
performance of a newly designed turbine follower controller.
Considering the drawbacks of previous works, an overall model is
developed to minimize the error between each subsystem model
output and the experimental data obtained at the actual power plant.
The developed model is organized in two main subsystems namely;
Boiler and Turbine. Considering each FFPP subsystem
characteristics, different modeling approaches are developed. For
economizer, evaporator, superheater and reheater, first order models
are determined based on principles of mass and energy conservation.
Simulations verify the accuracy of the developed models. Due to the
nonlinear characteristics of attemperator, a new model, based on a
genetic-fuzzy systems utilizing Pittsburgh approach is developed
showing a promising performance vis-à-vis those derived with other
methods like ANFIS. The optimization constraints are handled
utilizing penalty functions. The effect of increasing the number of
rules and membership functions on the performance of the proposed
model is also studied and evaluated. The turbine model is developed
based on the equation of adiabatic expansion. Parameters of all
evaluated models are tuned by means of evolutionary algorithms.
Based on the developed model a fuzzy PI controller is developed. It
is then successfully implemented in the turbine follower control
strategy of the plant. In this control strategy instead of keeping
control parameters constant, they are adjusted on-line with regard to
the error and the error rate. It is shown that the response of the
system improves significantly. It is also shown that fuel consumption
decreases considerably.
Abstract: The separation efficiency of a hydrocyclone has
extensively been considered on the rigid particle assumption. A
collection of experimental studies have demonstrated their
discrepancies from the modeling and simulation results. These
discrepancies caused by the actual particle elasticity have generally
led to a larger amount of energy consumption in the separation
process. In this paper, the influence of particle elasticity on the
separation efficiency of a hydrocyclone system was investigated
through the Finite Element (FE) simulations using crude oil droplets
as the elastic particles. A Reitema-s design hydrocyclone with a
diameter of 8 mm was employed to investigate the separation
mechanism of the crude oil droplets from water. The cut-size
diameter eter of the crude oil was 10 - Ðçm in order to fit with the
operating range of the adopted hydrocylone model. Typical
parameters influencing the performance of hydrocyclone were varied
with the feed pressure in the range of 0.3 - 0.6 MPa and feed
concentration between 0.05 – 0.1 w%. In the simulation, the Finite
Element scheme was applied to investigate the particle-flow
interaction occurred in the crude oil system during the process. The
interaction of a single oil droplet at the size of 10 - Ðçm to the flow
field was observed. The feed concentration fell in the dilute flow
regime so the particle-particle interaction was ignored in the study.
The results exhibited the higher power requirement for the separation
of the elastic particulate system when compared with the rigid
particulate system.
Abstract: Flash memory has become an important storage device
in many embedded systems because of its high performance, low
power consumption and shock resistance. Multi-level cell (MLC) is
developed as an effective solution for reducing the cost and increasing
the storage density in recent years. However, most of flash file system
cannot handle the error correction sufficiently. To correct more errors
for MLC, we implement Reed-Solomon (RS) code to YAFFS, what is
widely used for flash-based file system. RS code has longer computing
time but the correcting ability is much higher than that of Hamming
code.
Abstract: Bay leaves have been shown to improve insulin
function in vitro but the effects on people have not been determined.
The objective of this study was to determine if bay leaves may be
important in the prevention and/or alleviation of type 1 diabetes.
Methods: Fifty five people with type 1 diabetes were divided into
two groups, 45 given capsules containing 3 g of bay leaves per day
for 30 days and 10 given a placebo capsules. Results All the patients
consumed bay leaves shows reduced serum glucose with significant
decreases 27% after 30 d. Total cholesterol decreased, 21 %, after 30
days with larger decreases in low density lipoprotein (LDL) 24%.
High density lipoprotein (HDL) increased 20% and Triglycerides
also decreased 26%. There were no significant changes in the
placebo group. Conclusion, this study demonstrates that consumption
of bay leaves, 3 g/d for 30 days, decreases risk factors for diabetes
and cardiovascular diseases and suggests that bay leaves may be
beneficial for people with type 1 diabetes.
Abstract: Directive 2009/28/CE establishes, as obligatory objective, a share of renewable energies on energetic consumption of 20%, in European Union, in 2020 However, such European normative gives freedom to member states in the selection of the renewable promotion mechanism that allows them to obtain that objective. In this paper, we analyze the main characteristics of the promotion mechanisms of renewable energy used in the countries that shape the Electricity Iberian Market (Spain and Portugal) and the results in employment. The importance of these countries is given by the great increasing of the renewable energies which suppose a share higher than 30% of the overall generation in 2010. Therefore, this research paper can serve as the basis for the learning of other countries with regard to the main advantages that entail the use of a feed-in tariff system.
Abstract: Efficient modulo 2n+1 adders are important for
several applications including residue number system, digital signal
processors and cryptography algorithms. In this paper we present a
novel modulo 2n+1 addition algorithm for a recently represented
number system. The proposed approach is introduced for the
reduction of the power dissipated. In a conventional modulo 2n+1
adder, all operands have (n+1)-bit length. To avoid using (n+1)-bit
circuits, the diminished-1 and carry save diminished-1 number
systems can be effectively used in applications. In the paper, we also
derive two new architectures for designing modulo 2n+1 adder, based
on n-bit ripple-carry adder. The first architecture is a faster design
whereas the second one uses less hardware. In the proposed method,
the special treatment required for zero operands in Diminished-1
number system is removed. In the fastest modulo 2n+1 adders in
normal binary system, there are 3-operand adders. This problem is
also resolved in this paper. The proposed architectures are compared
with some efficient adders based on ripple-carry adder and highspeed
adder. It is shown that the hardware overhead and power
consumption will be reduced. As well as power reduction, in some
cases, power-delay product will be also reduced.
Abstract: Wireless Sensor Network is Multi hop Self-configuring
Wireless Network consisting of sensor nodes. The deployment of
wireless sensor networks in many application areas, e.g., aggregation
services, requires self-organization of the network nodes into clusters.
Efficient way to enhance the lifetime of the system is to partition the
network into distinct clusters with a high energy node as cluster head.
The different methods of node clustering techniques have appeared in
the literature, and roughly fall into two families; those based on the
construction of a dominating set and those which are based solely on
energy considerations. Energy optimized cluster formation for a set
of randomly scattered wireless sensors is presented. Sensors within a
cluster are expected to be communicating with cluster head only. The
energy constraint and limited computing resources of the sensor nodes
present the major challenges in gathering the data. In this paper we
propose a framework to study how partially correlated data affect the
performance of clustering algorithms. The total energy consumption
and network lifetime can be analyzed by combining random geometry
techniques and rate distortion theory. We also present the relation
between compression distortion and data correlation.
Abstract: Recently ORC(Organic Rankine Cycle) has attracted
much attention due to its potential in reducing consumption of fossil
fuels and its favorable characteristics to exploit low-grade heat sources.
In this work thermodynamic performance of ORC with superheating of
vapor is comparatively assessed for various working fluids. Special
attention is paid to the effects of system parameters such as the evaporating
temperature and the turbine inlet temperature on the characteristics
of the system such as maximum possible work extraction from
the given source, volumetric flow rate per 1 kW of net work and
quality of the working fluid at turbine exit as well as thermal and
exergy efficiencies. Results show that for a given source the thermal
efficiency increases with decrease of the superheating but exergy
efficiency may have a maximum value with respect to the superheating
of the working fluid. Results also show that in selection of working
fluid it is required to consider various criteria of performance characteristics
as well as thermal efficiency.
Abstract: Nowadays, the importance of energy saving is clearance to everyone. By attention to increasing price of fuels and also the problems of environment pollutions, there are the most efforts for using fuels littler and more optimum in everywhere. This essay studies optimizing of gas consumption in gas-burner space heaters. In oven of each gas-burner space heaters there is two snags to prevent the hot air (the result of combustion of natural gas) to go out of oven of the gas-burner space heaters directly without delivering its heat to the space of favorite environment like a room. These snags cause a excess circulating that helps hot air deliver its heat to the space of favorite environment. It means the exhaust air temperature will be decreased then when there are no snags. This is the aim of this essay to use maximum potential energy of the natural gas to make heat. In this study, by the help of a finite volume software (FLUENT) consumption of the gas-burner space heaters is simulated and optimized. At the end of this writing, by comparing the results of software and experimental results, it will be proved the authenticity of this method.
Abstract: Server provisioning is one of the most attractive topics in virtualization systems. Virtualization is a method of running multiple independent virtual operating systems on a single physical computer. It is a way of maximizing physical resources to maximize the investment in hardware. Additionally, it can help to consolidate servers, improve hardware utilization and reduce the consumption of power and physical space in the data center. However, management of heterogeneous workloads, especially for resource utilization of the server, or so called provisioning becomes a challenge. In this paper, a new concept for managing workloads based on user behavior is presented. The experimental results show that user behaviors are different in each type of service workload and time. Understanding user behaviors may improve the efficiency of management in provisioning concept. This preliminary study may be an approach to improve management of data centers running heterogeneous workloads for provisioning in virtualization system.
Abstract: In the current decade, wireless sensor networks are
emerging as a peculiar multi-disciplinary research area. By this
way, energy efficiency is one of the fundamental research themes
in the design of Medium Access Control (MAC) protocols for
wireless sensor networks. Thus, in order to optimize the energy
consumption in these networks, a variety of MAC protocols are
available in the literature. These schemes were commonly evaluated
under simple network density and a few results are published on
their robustness in realistic network-s size. We, in this paper, provide
an analytical study aiming to highlight the energy waste sources in
wireless sensor networks. Then, we experiment three energy efficient
hybrid CSMA/CA based MAC protocols optimized for wireless
sensor networks: Sensor-MAC (SMAC), Time-out MAC (TMAC)
and Traffic aware Energy Efficient MAC (TEEM). We investigate
these protocols with different network densities in order to discuss
the end-to-end performances of these schemes (i.e. in terms of energy
efficiency, delay and throughput). Through Network Simulator (NS-
2) implementations, we explore the behaviors of these protocols with
respect to the network density. In fact, this study may help the multihops
sensor networks designers to design or select the MAC layer
which matches better their applications aims.