Abstract: In the Lost Foam Casting process, melting point
temperature of metal, as well as volume and rate of the foam
degradation have significant effect on the mold filling pattern.
Therefore, gas generation capacity and gas gap length are two
important parameters for modeling of mold filling time of the lost
foam casting processes. In this paper, the gas gap length at the liquidfoam
interface for a low melting point (aluminum) alloy and a high
melting point (Carbon-steel) alloy are investigated by the
photography technique. Results of the photography technique
indicated, that the gas gap length and the mold filling time are
increased with increased coating thickness and density of the foam.
The Gas gap lengths measured in aluminum and Carbon-steel,
depend on the foam density, and were approximately 4-5 and 25-60
mm, respectively. By using a new system, the gas generation
capacity for the aluminum and steel was measured. The gas
generation capacity measurements indicated that gas generation in
the Aluminum and Carbon-steel lost foam casting was about 50 CC/g
and 3200 CC/g polystyrene, respectively.
Abstract: This work discusses an innovative methodology for
deployment of service quality characteristics. Four groups of organizational features that may influence the quality of services are identified: human resource, technology, planning, and organizational
relationships. A House of Service Quality (HOSQ) matrix is built to
extract the desired improvement in the service quality characteristics
and to translate them into a hierarchy of important organizational
features. The Mean Square Error (MSE) criterion enables the
pinpointing of the few essential service quality characteristics to be
improved as well as selection of the vital organizational features. The
method was implemented in an engineering supply enterprise and
provides useful information on its vital service dimensions.
Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: A method is presented for the construction of arbitrary
even-input sorting networks exhibiting better properties than the
networks created using a conventional technique of the same type.
The method was discovered by means of a genetic algorithm combined
with an application-specific development. Similarly to human
inventions in the area of theoretical computer science, the evolved
invention was analyzed: its generality was proven and area and time
complexities were determined.
Abstract: Enterprise Wide Information Systems (EWIS)
implementation involves the entire business and will require changes
throughout the firm. Because of the scope, complexity and
continuous nature of ERP, the project-based approach to managing
the implementation process resulted in failure rates of between 60%
and 80%. In recent years ERP systems have received much attention.
The organizational relevance and risk of ERP projects make it
important for organizations to focus on ways to make ERP
implementation successful. Once these systems are in place,
however, their performance depends on the identified macro
variables viz. 'Business Process', 'Decision Making' and 'Individual
/ Group working'. The questionnaire was designed and administered.
The responses from 92 organizations were compiled. The
relationship of these variables with EWIS performance is analyzed
using inferential statistical measurements. The study helps to
understand the performance of model presented. The study suggested
in keeping away from the calamities and thereby giving the
necessary competitive edge. Whenever some discrepancy is
identified during the process of performance appraisal care has to be
taken to draft necessary preventive measures. If all these measures
are taken care off then the EWIS performance will definitely deliver
the results.
Abstract: Fick's second law equations for unsteady state
diffusion of salt into the potato tissues were solved numerically. The
set of equations resulted from implicit modeling were solved using
Thomas method to find the salt concentration profiles in solid phase.
The needed effective diffusivity and equilibrium distribution
coefficient were determined experimentally. Cylindrical samples of
potato were infused with aqueous NaCl solutions of 1-3%
concentrations, and variations in salt concentrations of brine were
determined over time. Solute concentrations profiles of samples were
determined by measuring salt uptake of potato slices. For the studied
conditions, equilibrium distribution coefficients were found to be
dependent on salt concentrations, whereas the effective diffusivity
was slightly affected by brine concentration.
Abstract: There is a growing body of evidence to support the
proposition of product take back for remanufacturing particularly
within the context of Extended Producer Responsibility (EPR).
Remanufacturing however presents challenges unlike that of
traditional manufacturing environments due to its high levels of
uncertainty which may further distract organizations from
considering its potential benefits. This paper presents a novel
modeling approach for evaluating the uncertainty of part failures
within the remanufacturing process and its impact on economic and
environmental performance measures. This paper presents both the
theoretical modeling approach and an example of its use in
application.
Abstract: Effect of high temperature exposure on properties of cement mortar containing municipal solid waste incineration (MSWI) bottom ash as partial natural aggregate replacement is analyzed in the paper. The measurements of mechanical properties, bulk density, matrix density, total open porosity, sorption and desorption isotherms are done on samples exposed to the temperatures of 20°C to 1000°C. TGA analysis is performed as well. Finally, the studied samples are analyzed by IR spectroscopy in order to evaluate TGA data.
Abstract: This paper describes a novel and effective approach to content-based image retrieval (CBIR) that represents each image in the database by a vector of feature values called “Standard deviation of mean vectors of color distribution of rows and columns of images for CBIR". In many areas of commerce, government, academia, and hospitals, large collections of digital images are being created. This paper describes the approach that uses contents as feature vector for retrieval of similar images. There are several classes of features that are used to specify queries: colour, texture, shape, spatial layout. Colour features are often easily obtained directly from the pixel intensities. In this paper feature extraction is done for the texture descriptor that is 'variance' and 'Variance of Variances'. First standard deviation of each row and column mean is calculated for R, G, and B planes. These six values are obtained for one image which acts as a feature vector. Secondly we calculate variance of the row and column of R, G and B planes of an image. Then six standard deviations of these variance sequences are calculated to form a feature vector of dimension six. We applied our approach to a database of 300 BMP images. We have determined the capability of automatic indexing by analyzing image content: color and texture as features and by applying a similarity measure Euclidean distance.
Abstract: Data mining is an extraordinarily demanding field referring to extraction of implicit knowledge and relationships, which are not explicitly stored in databases. A wide variety of methods of data mining have been introduced (classification, characterization, generalization...). Each one of these methods includes more than algorithm. A system of data mining implies different user categories,, which mean that the user-s behavior must be a component of the system. The problem at this level is to know which algorithm of which method to employ for an exploratory end, which one for a decisional end, and how can they collaborate and communicate. Agent paradigm presents a new way of conception and realizing of data mining system. The purpose is to combine different algorithms of data mining to prepare elements for decision-makers, benefiting from the possibilities offered by the multi-agent systems. In this paper the agent framework for data mining is introduced, and its overall architecture and functionality are presented. The validation is made on spatial data. Principal results will be presented.
Abstract: Noise contamination in a magnetic resonance (MR)
image could occur during acquisition, storage, and transmission in
which effective filtering is required to avoid repeating the MR
procedure. In this paper, an iterative asymmetrical triangle fuzzy
filter with moving average center (ATMAVi filter) is used to reduce
different levels of salt and pepper noise in a brain MR image. Besides
visual inspection on filtered images, the mean squared error (MSE) is
used as an objective measurement. When compared with the median
filter, simulation results indicate that the ATMAVi filter is effective
especially for filtering a higher level noise (such as noise density =
0.45) using a smaller window size (such as 3x3) when operated
iteratively or using a larger window size (such as 5x5) when operated
non-iteratively.
Abstract: In the present paper; an experimental and numerical
investigations of drag reduction on a grooved circular cylinder have
been performed. The experiments were carried out in closed circuit
subsonic wind tunnel (TE44); the pressure distribution on the
cylinder was conducted using a TE44DPS differential pressure
scanner and the drag forces were measured using the TE81 balance.
The display unit is linked to a computer, loaded with DATASLIM
software for data analysis and logging of result. The numerical study
was performed using the code ANSYS FLUENT solving the
Reynolds Averaged Navier-Stokes (RANS) equations. The k-ε and k-
ω SST models were tested. The results obtained from the
experimental and numerical investigations have showed a reduction
in the drag when using longitudinal grooves namely 2 and 6 on the
cylinder.
Abstract: Intelligence tests are series of tasks designed to measure the capacity to make abstractions, to learn, and to deal with novel situations. Testing of the visual abilities of the shape understanding system (SUS) is performed based on the visual intelligence tests. In this paper the progressive matrices tests are formulated as tasks given to SUS. These tests require good visual problem solving abilities of the human subject. SUS solves these tests by performing complex visual reasoning transforming the visual forms (tests) into the string forms. The experiment proved that the proposed method, which is part of the SUS visual understanding abilities, can solve a test that is very difficult for human subject.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: The purposes of this study are 1) to study the over 20-year attempt of Mahakan fort community to negotiate with Bangkok Metropolitan Administration (BMA) to remain in their residential area belonging to the state, and 2) to apply the new social and cultural dimension between the state and the community as an alternative for local participation in keeping their residential area. This is a qualitative research, and the findings reveal that the community claimed their ancestors’ right as owners of this piece of land for over 200 years. The community, therefore, requested to take part in the preservation of land, culture and local intellect and the area management in terms of being a learning resource on the cultural road in Rattanakosin Island. However, BMA imposed the law concerning the community area relocation in Rattanakosin Island. The result of law enforcement led to the failure of the area relocation, and the hard hit on physical structure of the area including the overall deterioration of the cultural road renovated in the year 1982, the 200 years’ celebration of Bangkok. The enforcement of law by the state required the move of the community, and the landscape improvement based on the capital city plan. However, this enforcement resulted in the unending conflicts between the community and the state, and the solution of this problem was unclear. At the same time the community has spent a long time opposing the state’s action, and preparing themselves by administrating the community behind Mahakan fortress with community administrative committee under the suggestion of external organization by registering all community members, providing funds for community administration. At the meantime the state lacked the continuation of the enforcement due to political problem and BMA’s administration problem. It is, therefore, suggested that an alternative solution to this problem lie at the negotiation between the state and the community with the purpose of the collaboration between the two to develop the area under the protective law of each side.
Abstract: In the paper, based on stochastic analysis theory and Lyapunov functional method, we discuss the mean square stability of impulsive stochastic delay differential equations with markovian switching and poisson jumps, and the sufficient conditions of mean square stability have been obtained. One example illustrates the main results. Furthermore, some well-known results are improved and generalized in the remarks.
Abstract: The main issue discussed is on the role of education system in the process of nation building as a means in uniting different community ethnics which later on, hoped to shape the future ethnic relation of this country. It is generally known that political socialization experienced by each ethnic community has given birth to a vernacular education system, separated along the ethnic line. Every community shapes their own education system based on their respective mother tongue language, however all are based on the same curriculum. As a result the role of education as a uniting force is not significantly effective. Historically, it has been shown that government efforts to unite the country education system under the wing of national education system (national school) is not that successful since every community (Chinese) will defend the existence of their community education system because they want to spur their mother tongue language. The clash between national education system and vernacular education system is the root cause of stalemate in the ethnic relation in Malaysia and it always becomes a flash point when the issue is raised. The question now is what is the best solution to enhance the national education system in multiethnic Malaysia?
Abstract: In production of medicinal plants, seed germination is
very important problem. The treated seeds (control, hydro priming
and ZnSO4) of Cumin (Cuminum cyminum L.) were evaluated at
germination and seedling growth for tolerance to salt (NaCl and
Na2SO4) conditions at the same water potentials of 0.0, -0.3, -0.6, -
0.9 and -1.2MPa. Electrical conductivity (EC) values of the NaCl
solutions were 0.0, 6.5, 12.7, 18.4 and 23.5 dSm-1, respectively. The
objective of the study was to determine factors responsible for
germination and early seedling growth due to salt toxicity or osmotic
effect and to optimize the best priming treatment for these stress
conditions. Results revealed that germination delayed in both
solutions, having variable germination with different priming
treatments. Germination, shoot and weight, root and shoot length
were higher but mean germination time and abnormal germination
percentage were lower in NaCl than Na2SO4 at the same water
potential. The root / shoot weight and R/S length increased with
increase in osmotic potential in both NaCl and Na2SO4 solutions.
NaCl had less inhibitor effect on seedling growth than the
germination. It was concluded that inhibition of germination at the
same water potential of NaCl and Na2SO4 resulted from salt toxicity
rather than osmotic effect. Hydro priming increased germination and
seedling growth under salt stress. This protocol has practical
importance and could be recommended to farmers to achieve higher
germination and uniform emergence under field conditions.
Abstract: The study of the generated defects on manufactured
parts shows the difficulty to maintain parts in their positions during
the machining process and to estimate them during the pre-process
plan. This work presents a contribution to the development of 3D
models for the optimization of the manufacturing tolerances. An
experimental study allows the measurement of the defects of part
positioning for the determination of ε and the choice of an optimal
setup of the part. An approach of 3D tolerance based on the small
displacements method permits the determination of the
manufacturing errors upstream. A developed tool, allows an
automatic generation of the tolerance intervals along the three axes.
Abstract: Titanium alloys like the modern alloy Ti 6Al 2Sn 4Zr 6Mo (Ti-6246) combine excellent specific mechanical properties and corrosion resistance. On the other hand,due to their material characteristics, machining of these alloys is difficult to perform. The aim of the current study is the analyses of wear mechanisms of coated cemented carbide tools applied in orthogonal cutting experiments of Ti-6246 alloy. Round bars were machined with standard coated tools in dry conditions on a CNC latheusing a wide range of cutting speeds and cutting depths. Tool wear mechanisms were afterwards investigated by means of stereo microscopy, optical microscopy, confocal microscopy and scanning electron microscopy. Wear mechanisms included fracture of the tool tip (total failure) and abrasion. Specific wear features like crater wear, micro cracks and built-up edgeformation appeared depending of the mechanical and thermal conditions generated in the workpiece surface by the cutting action.