Abstract: Facing the concern of the population to its environment and to climatic change, city planners are now considering the urban climate in their choices of planning. The urban climate, representing different urban morphologies across central Bangkok metropolitan area (BMA), are used to investigates the effects of both the composition and configuration of variables of urban morphology indicators on the summer diurnal range of urban climate, using correlation analyses and multiple linear regressions. Results show first indicate that approximately 92.6% of the variation in the average maximum daytime near-surface air temperature (Ta) was explained jointly by the two composition variables of urban morphology indicators including open space ratio (OSR) and floor area ratio (FAR). It has been possible to determine the membership of sample areas to the local climate zones (LCZs) using these urban morphology descriptors automatically computed with GIS and remote sensed data. Finally result found the temperature differences among zones of large separation, such as the city center could be respectively from 35.48±1.04ºC (Mean±S.D.) warmer than the outskirt of Bangkok on average for maximum daytime near surface temperature to 28.27±0.21ºC for extreme event and, can exceed as 8ºC. A spatially disaggregation of urban thermal responsiveness map would be helpful for several reasons. First, it would localize urban areas concerned by different climate behavior over summer daytime and be a good indicator of urban climate variability. Second, when overlaid with a land cover map, this map may contribute to identify possible urban management strategies to reduce heat wave effects in BMA.
Abstract: The paper presents the Romanian realities and perspectives from the point of view of reaching the sustainable development model in the context of the recent accession to the European Union, based on the analysis of the indicators listed in the EU Sustainable Development Strategy. The analysis of the economic-social potential for sustainable development and of the environment aspects show that the objectives stipulated in the renewed EU Sustainable Development Strategy of 2006 can be reached, but an extra effort must be put-in in order to overcome the existing substantial gaps in several areas in relation to the developed countries of the EU. The paper-s conclusions show that even if sustainable development is not an easy target to reach in Romania, there are resources and a growing potential, which can lead to sustainable development if used rationally.
Abstract: Modern Society is strongly dependent on a reliable
power supply. The availability of cheap and reliable supply of
electrical energy is an indicator of societal welfare. Uninterrupted
reliable operation of a modern power system depends to a great
extent on reliable and satisfactory performance of insulators under
different environmental conditions. This paper reports result of
natural pollution tests that have been done at sites around city of
Aligarh (India). Flashover voltage per insulation distance (FOVUID)
of porcelain disc insulator for different pH values, ESDD has been
recorded for proper correlation between electrical and chemical
parameters. The pH of the contaminants has been suggested to be an
effective pollution severity indicator and may be used as a diagnostic
parameter for proper maintenance of porcelain insulators.
Abstract: The use of technology is increasingly adopted to
support flexible learning in Higher Education institutions. The
adoption of more sophisticated technologies offers a broad range of
facilities for communication and resource sharing, thereby creating a
flexible learning environment that facilitates and even encourages
students not to physically attend classes. However this emerging
trend seems to contradict class attendance requirements within
universities, inevitably leading to a dilemma between amending
traditional regulations and creating new policies for the higher
education institutions. This study presents an investigation into
student engagement in a technology enhanced/driven flexible
environment along with its relationship to attainment. We propose an
approach to modelling engagement from different perspectives in
terms of indicators and then consider what impact these indicators
have on student academic performance. We have carried out a case
study on the relation between attendance and attainment in a flexible
environment. Although our preliminary results show attendance is
quantitatively correlated with successful student development and
learning outcomes, our results also indicate there is a cohort that did
not follow such a pattern. Nevertheless the preliminary results could
provide an insight into pilot studies in the wider deployment of new
technology to support flexible learning.
Abstract: Globalisation is a phenomenon that cannot be avoided.
As globalisation allowed free flow of inputs including labour, it may
affect job opportunities for the locals. Therefore, investigate the
determinants of labour supply is essential in understanding the
structure of labour market in the new era of globalization. The
objective of this article is to examine labour supply by taking into
account the globalisation effect. The study covers 3885 households in
Peninsular Malaysia who are chosen using stratified random
sampling. The labour supply model will be the basis for the analysis.
The basic labour supply determinants are own wage and non-labour
income. However, the extended labour supply model incorporates
other variables like spouse wage，number of children and
individuals characteristics like education level and age. Besides, the
globalization indicator will also be incorporated as another
independent variable.
Abstract: Hospitals in southern Hualien teamed with the
Hypertension Joint Care Network. Working with the network, the
team provided a special designed health education to the individual
who had been identified as a hypertension patient in the outpatient
department. Some metabolism improvements achieved. This is a
retrospective study by purposively taking 106 patients from a hospital
between 2008 and 2010. Records of before and after education
intervention of the objects was collected and analyzed to see the how
the intervention affected the patients- hypertension control via clinical
parameter monitoring. The results showed that the clinical indicators,
the LDL-C, the cholesterol and the systolic blood pressure were
significantly improved. The study provides evidence for the
effectiveness of the network in controlling hypertension.
Abstract: Uranium mining and processing in Brazil occur in a
northeastern area near to Caetité-BA. Several Non-Governmental
Organizations claim that uranium mining in this region is a pollutant
causing health risks to the local population,but those in charge of the
complex extraction and production of“yellow cake" for generating
fuel to the nuclear power plants reject these allegations. This study
aimed at identifying potential problems caused by mining to the
population of Caetité. In this, work,the concentrations of 238U, 232Th
and 40K radioisotopes in the teeth of the Caetité population were
determined by ICP-MS. Teeth are used as bioindicators of
incorporated radionuclides. Cumulative radiation doses in the
skeleton were also determined. The concentration values were below
0.008 ppm, and annual effective dose due to radioisotopes are below
to the reference values. Therefore, it is not possible to state that the
mining process in Caetité increases pollution or radiation exposure in
a meaningful way.
Abstract: Since 2008 a new economic crisis is present is the
entire planet. This crisis affects several domains of the economic but
also of the social life. Consumption decreases due to the lack of
necessary resources of households to increase their expenditures. The
car manufacturing is one of the main industrial activities in European
Union (EU) and the present crisis particularly affects it. The present
study examines the correlations between several socio-economic
indicators and car market in European Union. The target is to find out
the impact of the present economic crisis on the car market in EU.
Abstract: In this research, a part of Aghche basin in Isfahan
province with an area about 2000 hectars, was chosen to be obtain
curve number coefficient runoff and W indicator in second Cook
method By using aerial photos 1968 and 1995, the satellite data of
the IRS in 2008. Then the process of land use changes in the period
of study and its effect on the changes of curve number (CN), W
indicator and surface runoff coefficient (C) of the basin was
investigated. These results showed that on the track of these land use
changes the weight averages curve number (CN), surface runoff
coefficient (C) and W indicator of the basin were increased to 0.92,
0.02 and 0.78 unit in the first period of study and 1.18, 0.03, 0.99
Unit in the second period of study respectively.
Abstract: The use of bioindicators plants (lichens, bryophytes
and Sphagnum....) in monitoring pollution by heavy metals has been
the subject of several works. However, few studies have addressed
the impact of specific type-s pollutants (fertilizers, pesticides.) on
these organisms.
We propose in this work to make the highlighting effect of NPKs
(NPK: nitrogen-phosphate-potassium-sulfate (NP2O5K2O) (15,15,15),
at concentrations of 10, 20, 30 , 40 and 50mM/L) on the activity of
detoxification enzymes (GSH/GST, CAT, APX and MDA) of plant
bioindicators (mosses and lichens) after treatment for 3 and 7 days.
This study shows the important role of the defense system in the
accumulation and tolerance to chemical pollutants through the
activation of enzymatic (GST (glutathione-S-transferase, APX
(ascorbat peroxidase), CAT (catalase)) and nonenzymatic biomarkers
(GSH (glutathione), MDA (malondialdehyde)) against oxidative
stress generated by the NPKs.
Abstract: This paper presents comparative study on recent
integer DCTs and a new method to construct a low sensitive structure
of integer DCT for colored input signals. The method refers to
sensitivity of multiplier coefficients to finite word length as an
indicator of how word length truncation effects on quality of output
signal. The sensitivity is also theoretically evaluated as a function of
auto-correlation and covariance matrix of input signal. The structure of
integer DCT algorithm is optimized by combination of lower sensitive
lifting structure types of IRT. It is evaluated by the sensitivity of
multiplier coefficients to finite word length expression in a function of
covariance matrix of input signal. Effectiveness of the optimum
combination of IRT in integer DCT algorithm is confirmed by quality
improvement comparing with existing case. As a result, the optimum
combination of IRT in each integer DCT algorithm evidently improves
output signal quality and it is still compatible with the existing one.
Abstract: Economically transformers constitute one of the largest investments in a Power system. For this reason, transformer condition assessment and management is a high priority task. If a transformer fails, it would have a significant negative impact on revenue and service reliability. Monitoring the state of health of power transformers has traditionally been carried out using laboratory Dissolved Gas Analysis (DGA) tests performed at periodic intervals on the oil sample, collected from the transformers. DGA of transformer oil is the single best indicator of a transformer-s overall condition and is a universal practice today, which started somewhere in the 1960s. Failure can occur in a transformer due to different reasons. Some failures can be limited or prevented by maintenance. Oil filtration is one of the methods to remove the dissolve gases and prevent the deterioration of the oil. In this paper we analysis the DGA data by regression method and predict the gas concentration in the oil in the future. We bring about a comparative study of different traditional methods of regression and the errors generated out of their predictions. With the help of these data we can deduce the health of the transformer by finding the type of fault if it has occurred or will occur in future. Additional in this paper effect of filtration on the transformer health is highlight by calculating the probability of failure of a transformer with and without oil filtrating.
Abstract: As the gradual increase of the enterprise scale, the
firms may possess many manufacturing plants located in different
places geographically. This change will result in the multi-site
production planning problems under the environment of multiple
plants or production resources. Our research proposes the structural
framework to analyze the multi-site planning problems. The analytical
framework is composed of six elements: multi-site conceptual model,
product structure (bill of manufacturing), production strategy,
manufacturing capability and characteristics, production planning
constraints, and key performance indicators. As well as the discussion
of these six ingredients, we also review related literatures in this paper
to match our analytical framework. Finally we take a real-world
practical example of a TFT-LCD manufacturer in Taiwan to explain
our proposed analytical framework for the multi-site production
planning problems.
Abstract: The purpose of this article is to analyze the market structure as well as the degree of concentration in insurance markets in new EU member states. The analysis was conducted using several most commonly used concentration indicators such as concentration ratio, Herfindahl-Hirschman index and entropy index. These indicators were calculated for the 2000-2010 period on the basis of total gross written premium as the most relevant indicator of market power in insurance markets. The results of the analysis showed that in all observed countries the level of concentration decreased, though with significantly different intensity. Yet, in some countries, the level of concentration remains very high.
Abstract: In this paper by measuring the cutting forces the effect
of the tool shape and qualifications (sharp and worn cutting tools of
both vee and knife edge profile) and cutting conditions (depth of cut
and cutting speed) in the turning operation on the tool deflection and
cutting force is investigated. The workpiece material was mild steel
and the cutting tool was made of high speed steel. Cutting forces
were measured by a dynamometer (type P.E.I. serial No 154). The
dynamometer essentially consisted of a cantilever structure which
held the cutting tool. Deflection of the cantilever was measured by an
L.V.D.T (Mercer 122) deflection indicator. No cutting fluid was used
during the turning operations. A modern CNC lathe machine (Okuma
LH35-N) was used for the tests. It was noted that worn vee profile
tools tended to produce a greater increase in the vertical force
component than the axial component, whereas knife tools tended to
show a more pronounced increase in the axial component.
Abstract: Sputum smear conversion after one month of antituberculosis
therapy in new smear positive pulmonary tuberculosis
patients (PTB+) is a vital indicator towards treatment success. The
objective of this study is to determine the rate of sputum smear
conversion in new PTB+ patients after one month under treatment of
National Institute of Diseases of the Chest and Hospital (NIDCH).
Analysis of sputum smear conversion was done by re-clinical
examination with sputum smear microscopic test after one month.
Socio-demographic and hematological parameters were evaluated to
perceive the correlation with the disease status. Among all enrolled
patients only 33.33% were available for follow up diagnosis and of
them only 42.86% patients turned to smear negative. Probably this
consequence is due to non-coherence to the proper disease
management. 66.67% and 78.78% patients reported low haemoglobin
and packed cell volume level respectively whereas 80% and 93.33%
patients accounted accelerated platelet count and erythrocyte
sedimentation rate correspondingly.
Abstract: A concrete structure is designed and constructed for its
purpose of use, and is expected to maintain its function for the target
durable years from when it was planned. Nevertheless, as time elapses
the structure gradually deteriorates and then eventually degrades to the
point where the structure cannot exert the function for which it was
planned. The performance of concrete that is able to maintain the level
of the performance required over the designed period of use as it has
less deterioration caused by the elapse of time under the designed
condition is referred to as Durability. There are a number of causes of
durability degradation, but especially chloride damage, carbonation,
freeze-thaw, etc are the main causes. In this study, carbonation, one of
the main causes of deterioration of the durability of a concrete
structure, was investigated via a microstructure analysis technique.
The method for the measurement of carbonation was studied using the
existing indicator method, and the method of measuring the progress
of carbonation in a quantitative manner was simultaneously studied
using a FT-IR (Fourier-Transform Infrared) Spectrometer along with
the microstructure analysis technique.
Abstract: Fecal sterol has been proposed as a chemical indicator
of human fecal pollution even when fecal coliform populations have
diminished due to water chlorination or toxic effects of industrial
effluents. This paper describes an improved derivatization procedure
for simultaneous determination of four fecal sterols including
coprostanol, epicholestanol, cholesterol and cholestanol using gas
chromatography-mass spectrometry (GC-MS), via optimization study
on silylation procedures using N-O-bis
(trimethylsilyl)-trifluoroacetamide (BSTFA), and
N-(tert-butyldimethylsilyl)-N-methyltrifluoroacetamide
(MTBSTFA), which lead to the formation of trimethylsilyl (TMS) and
tert-butyldimethylsilyl (TBS) derivatives, respectively. Two
derivatization processes of injection-port derivatization and water bath
derivatization (60 oC, 1h) were inspected and compared. Furthermore,
the methylation procedure at 25 oC for 2h with
trimethylsilydiazomethane (TMSD) for fecal sterols analysis was also
studied. It was found that most of TMS derivatives demonstrated the
highest sensitivities, followed by methylated derivatives. For BSTFA
or MTBSTFA derivatization processes, the simple injection-port
derivatization process could achieve the same efficiency as that in the
tedious water bath derivatization procedure.
Abstract: This article illustrates a model selection management approach for virtual prototypes in interactive simulations. In those numerical simulations, the virtual prototype and its environment are modelled as a multiagent system, where every entity (prototype,human, etc.) is modelled as an agent. In particular, virtual prototyp ingagents that provide mathematical models of mechanical behaviour inform of computational methods are considered. This work argues that selection of an appropriate model in a changing environment,supported by models? characteristics, can be managed by the deter-mination a priori of specific exploitation and performance measures of virtual prototype models. As different models exist to represent a single phenomenon, it is not always possible to select the best one under all possible circumstances of the environment. Instead the most appropriate shall be selecting according to the use case. The proposed approach consists in identifying relevant metrics or indicators for each group of models (e.g. entity models, global model), formulate their qualification, analyse the performance, and apply the qualification criteria. Then, a model can be selected based on the performance prediction obtained from its qualification. The authors hope that this approach will not only help to inform engineers and researchers about another approach for selecting virtual prototype models, but also assist virtual prototype engineers in the systematic or automatic model selection.
Abstract: The ultimate goal of this article is to develop a robust and accurate numerical method for solving hyperbolic conservation laws in one and two dimensions. A hybrid numerical method, coupling a cheap fourth order total variation diminishing (TVD) scheme [1] for smooth region and a Robust seventh-order weighted non-oscillatory (WENO) scheme [2] near discontinuities, is considered. High order multi-resolution analysis is used to detect the high gradients regions of the numerical solution in order to capture the shocks with the WENO scheme, while the smooth regions are computed with fourth order total variation diminishing (TVD). For time integration, we use the third order TVD Runge-Kutta scheme. The accuracy of the resulting hybrid high order scheme is comparable with these of WENO, but with significant decrease of the CPU cost. Numerical demonstrates that the proposed scheme is comparable to the high order WENO scheme and superior to the fourth order TVD scheme. Our scheme has the added advantage of simplicity and computational efficiency. Numerical tests are presented which show the robustness and effectiveness of the proposed scheme.