Abstract: No negative control nor control to prevent microbes from escaping was set when the S-shaped flask experiments were performed by Pasteur. Microscope was not used to observe the media in the flasks. Louis Pasteur’s S-shaped flask experiment was re-examined by using U-shaped flasks, modified S-shaped flasks and microscope. A mixture of microbes was isolated from the room air, from which one rod-shaped Bacillus species with proposed name Bacillus gaso-mobilis sp nov and one grape-shaped Staphylococcus species with proposed name of Staphylococcus gaso-mobilis sp nov were identified. Their penicillin and ampicillin resistant strains containing plasmids were isolated. These bacteria could change color, produce odor and automatically move in the air. They did not form colonies on solid media. They had a high suspension capacity in liquid media. Their light absorbance peaked at the wave length of 320 nm. It was concluded that there were flaws with Louis Pasteur’s S-shaped flask experiments.
Abstract: Pore water pressure is normally because of
consolidation, compaction and water level fluctuation on reservoir.
Measuring, controlling and analyzing of pore water pressure have
significant importance in both of construction and operation period.
Since end of 2002, (dam start up) nature of KARKHEH dam has
been analyzed by using the gathered information from
instrumentation system of dam. In this lecture dam condition after
start up have been analyzed by using the gathered data from located
piezometers in core of dam. According to TERZAGHI equation and
records of piezometers, consolidation lasted around five years during
early years of construction stage, and current pore water pressure in
core of dam is caused by water level fluctuation in reservoir.
Although there is time lag between water level fluctuation and results
of piezometers. These time lags have been checked and the results
clearly show that one of the most important causes of it is distance
between piezometer and reservoir.
Abstract: An accurate prediction of the minimum fluidization
velocity is a crucial hydrodynamic aspect of the design of fluidized
bed reactors. Common approaches for the prediction of the minimum
fluidization velocities of binary-solid fluidized beds are first
discussed here. The data of our own careful experimental
investigation involving a binary-solid pair fluidized with water is
presented. The effect of the relative composition of the two solid
species comprising the fluidized bed on the bed void fraction at the
incipient fluidization condition is reported and its influence on the
minimum fluidization velocity is discussed. In this connection, the
capability of packing models to predict the bed void fraction is also
examined.
Abstract: The porous silicon (PS), formed from the anodization
of a p+ type substrate silicon, consists of a network organized in a
pseudo-column as structure of multiple side ramifications. Structural
micro-topology can be interpreted as the fraction of the interconnected
solid phase contributing to thermal transport. The
reduction of dimensions of silicon of each nanocristallite during the
oxidation induced a reduction in thermal conductivity. Integration of
thermal sensors in the Microsystems silicon requires an effective
insulation of the sensor element. Indeed, the low thermal conductivity
of PS consists in a very promising way in the fabrication of integrated
thermal Microsystems.In this work we are interesting in the
measurements of thermal conductivity (on the surface and in depth)
of PS by the micro-Raman spectroscopy. The thermal conductivity is
studied according to the parameters of anodization (initial doping and
current density. We also, determine porosity of samples by
spectroellipsometry.
Abstract: MM-Path, an acronym for Method/Message Path, describes the dynamic interactions between methods in object-oriented systems. This paper discusses the classifications of MM-Path, based on the characteristics of object-oriented software. We categorize it according to the generation reasons, the effect scope and the composition of MM-Path. A formalized representation of MM-Path is also proposed, which has considered the influence of state on response method sequences of messages. .Moreover, an automatic MM-Path generation approach based on UML Statechart diagram has been presented, and the difficulties in identifying and generating MM-Path can be solved. . As a result, it provides a solid foundation for further research on test cases generation based on MM-Path.
Abstract: Vortices can develop in intakes of turbojet and turbo
fan aero engines during high power operation in the vicinity of solid
surfaces. These vortices can cause catastrophic damage to the engine.
The factors determining the formation of the vortex include both
geometric dimensions as well as flow parameters. It was shown that
the threshold at which the vortex forms or disappears is also
dependent on the initial flow condition (i.e. whether a vortex forms
after stabilised non vortex flow or vice-versa). A computational fluid
dynamics study was conducted to determine the difference in
thresholds between the two conditions. This is the first reported
numerical investigation of the “memory effect". The numerical
results reproduce the phenomenon reported in previous experimental
studies and additional factors, which had not been previously studied,
were investigated. They are the rate at which ambient velocity
changes and the initial value of ambient velocity. The former was
found to cause a shift in the threshold but not the later. It was also
found that the varying condition thresholds are not symmetrical about
the neutral threshold. The vortex to no vortex threshold lie slightly
further away from the neutral threshold compared to the no vortex to
vortex threshold. The results suggests that experimental investigation
of vortex formation threshold performed either in vortex to no vortex
conditions, or vice versa, solely may introduce mis-predictions
greater than 10%.
Abstract: The Beshar River is one of the most important aquatic ecosystems in the upstream of the Karun watershed in south of Iran which is affected by point and non point pollutant sources . This study was done in order to evaluate the effects of pollutants activities on the water quality of the Beshar river and its aquatic ecosystems. This river is approximately 190 km in length and situated at the geographical positions of 51° 20´ to 51° 48´ E and 30° 18´ to 30° 52´ N it is one of the most important aquatic ecosystems of Kohkiloye and Boyerahmad province in south-west Iran. In this research project, five study stations were selected to examine water pollution in the Beshar River systems. Human activity is now one of the most important factors affecting on hydrology and water quality of the Beshar river. Humans use large amounts of resources to sustain various standards of living, although measures of sustainability are highly variable depending on how sustainability is defined. The Beshar river ecosystems are particularly sensitive and vulnerable to human activities. Therefore, to determine the impact of human activities on the Beshar River, the most important water quality parameters such as pH, dissolve oxygen (DO), Biological Oxygen Demand (BOD5), Total Dissolve Solids (TDS), Nitrates (NO3-N) and Phosphates (PO4) were estimated at the five stations. As the results show, the most important pollution index parameters such as BOD5, NO3 and PO4 increase and DO and pH decrease according to human activities (P
Abstract: The problem of N cracks interaction in an isotropic
elastic solid is decomposed into a subproblem of a homogeneous solid
without crack and N subproblems with each having a single crack
subjected to unknown tractions on the two crack faces. The unknown
tractions, namely pseudo tractions on each crack are expanded into
polynomials with unknown coefficients, which have to be determined
by the consistency condition, i.e. by the equivalence of the original
multiple cracks interaction problem and the superposition of the N+1
subproblems. In this paper, Kachanov-s approach of average tractions
is extended into the method of moments to approximately impose the
consistence condition. Hence Kachanov-s method can be viewed as
the zero-order method of moments. Numerical results of the stress
intensity factors are presented for interactions of two collinear cracks,
three collinear cracks, two parallel cracks, and three parallel cracks.
As the order of moment increases, the accuracy of the method of
moments improves.
Abstract: The ongoing effort to develop an in-house
compressible solver with multi-disciplinary physics is presented in
this paper. Basic compressible solver combined with IBM technique
provides us an effective numerical tool able to tackle the physics
phenomena and especially physic phenomena involved in Solid
Rocket Motors (SRMs). Main principles are introduced step by step
describing its implementation. This paper sheds light on the whole
potentiality of our proposed numerical model and we strongly believe
a way to introduce multi-physics mechanisms strongly coupled is
opened to ablation in nozzle, fluid/structure interaction and burning
propellant surface with time.
Abstract: Adsorption of proteins onto a solid surface is believed to be the initial and controlling step in biofouling. A better knowledge of the fouling process can be obtained by controlling the formation of the first protein layer at a solid surface. A number of methods have been investigated to inhibit adsorption of proteins. In this study, the adsorption kinetics of
Abstract: This paper describes a rapid prototyping (RP)
technology for forming a hydroxyapatite (HA) bone scaffold model.
The HA powder and a silica sol are mixed into bioceramic slurry form
under a suitable viscosity. The HA particles are embedded in the
solidified silica matrix to form green parts via a wide range of process
parameters after processing by selective laser sintering (SLS). The
results indicate that the proposed process was possible to fabricate
multilayers and hollow shell structure with brittle property but
sufficient integrity for handling prior to post-processing. The
fabricated bone scaffold models had a surface finish of 25
Abstract: Diesel Engines emit complex mixtures of inorganic
and organic compounds in the form of both solid and vapour phase
particles. Most of the particulates released are ultrafine nanoparticles
which are detrimental to human health and can easily enter the body
by respiration. The emissions standards on particulate matter release
from diesel engines are constantly upgraded within the European
Union and with future regulations based on the particles numbers
released instead of merely mass, the need for effective aftertreatment
devices will increase. Standard particulate filters in the form of wall
flow filters can have problems with high soot accumulation,
producing a large exhaust backpressure. A potential solution would
be to combine the standard filter with a flow through filter to reduce
the load on the wall flow filter. In this paper soot particle trapping has
been simulated in different continuous flow filters of monolithic
structure including the use of promoters, at laminar flow conditions.
An Euler Lagrange model, the discrete phase model in Ansys used
with user defined functions for forces acting on particles. A method
to quickly screen trapping of 5 nm and 10 nm particles in different
catalysts designs with tracers was also developed.
Simulations of square duct monoliths with promoters show that the
strength of the vortices produced are not enough to give a high
amount of particle deposition on the catalyst walls. The smallest
particles in the simulations, 5 and 10 nm particles were trapped to a
higher extent, than larger particles up to 1000 nm, in all studied
geometries with the predominant deposition mechanism being
Brownian diffusion. The comparison of the different filters designed
with a wall flow filter does show that the options for altering a design
of a flow through filter, without imposing a too large pressure drop
penalty are good.
Abstract: A statistical optimization was studied to design a media composition to produce optimum cellulolytic enzyme where palm oil mill effluent (POME) as a basal medium and filamentous fungus, Trichoderma reesei RUT-C30 were used in the liquid state bioconversion(LSB). 2% (w/v) total suspended solid, TSS, of the POME supplemented with 1% (w/v) cellulose, 0.5%(w/v) peptone and 0.02% (v/v) Tween 80 was estimated to produce the optimum CMCase activity of 18.53 U/ml through the statistical analysis followed by the faced centered central composite design(FCCCD). The probability values of cellulose (
Abstract: To coop with urbanization issues and the economic need for expansion, the city of Jakarta is planning to reclaim more land in the Jakarta Bay. However, the reclamation activities of some islands have barely started and already the developers are facing difficulties in finding sufficient quantities of sand as fill material. When addressing the problem of sand scarcity in the case of Jakarta where, an excess of waste production, an inadequate solid waste management system and a lack of dumping ground pose a major problem, it is hard not to think of the use of waste as alternative fill material. This paper analyses the possibilities of using waste in the land reclamation projects, considering the governmental, social, environmental and economic context of the city. The results identify types of waste that could be used, ways of using those types of waste and implementation conditions for the city of Jakarta.
Abstract: This paper considers the design of a motion planner
that will simultaneously accomplish control and motion planning of a
n-link nonholonomic mobile manipulator, wherein, a n-link
holonomic manipulator is coupled with a nonholonomic mobile
platform, within an obstacle-ridden environment. This planner,
derived from the Lyapunov-based control scheme, generates
collision-free trajectories from an initial configuration to a final
configuration in a constrained environment cluttered with stationary
solid objects of different shapes and sizes. We demonstrate the
efficiency of the control scheme and the resulting acceleration
controllers of the mobile manipulator with results through computer
simulations of an interesting scenario.
Abstract: In the context of introduction of deregulatory policy measures and subsequent wave of mergers and acquisitions (M&A) in Indian corporate sector since 1991, the present paper attempts to examine the welfare implications of this wave. It is found that M&A do not have any significant impact on consumers- welfare. Instead, consumers- welfare is significantly influenced by exports intensity, imports intensity, advertising intensity, technology related efforts, and past profitability of the firms. While the industries with higher exports orientation or greater product differentiation or better financial performance experience greater loss in consumers- welfare, it is less in the industries with greater competition from imports or better technology. Hence, the wave of M&A in Indian manufacturing sector in the post-liberalization era may not be a matter of serious concern from consumers- welfare point of view. Instead, in many cases, M&A can help the firms in consolidating their business and enhancing competitiveness, and this may benefit the consumers in the form of greater efficiency and lower prices.
Abstract: Addition of an oily waste to a co-composting process of dairy cow manure with food waste, and the influence in the final product was evaluated. Three static composting piles with different substrates concentrations were assessed. Sawdust was also added to all composting piles to attain 60%, humidity at the beginning of the process. In pile 1, the co-substrates were the solid-phase of dairy cow manure, food waste and sawdust as bulking agent. In piles 2 and 3 there was an extra input of oily waste of 7 and 11% of the total volume, respectively, corresponding to 18 and 28% in dry weight. The results showed that the co-composting process was feasible even at the highest fat content. Another positive effect due to the oily waste addition was the requirement of extra humidity, due to the hydrophobic properties of this specific waste, which may imply reduced need of a bulking agent. Moreover, this study shows that composting can be a feasible way of adding value to fatty wastes. The three final composts presented very similar and suitable properties for land application.
Abstract: The purpose of this work was to inspect the potential
of vincristine-dextran complex loaded solid lipid nanoparticles for
drug delivery to the brain.
The nanoparticles were stained with a fluorescence dye and their
plasma pharmacokinetic and brain concentrations were investigated
following injection to rats.
The result revealed a significant improvement in the plasma
concentration profile of the SLN injected animals as well as a sharp
increased concentration in the brains.
Abstract: In the present work the internal sulfate attack on
pastes made from pure clinker phases was studied. Two binders were
produced: (a) a binder with 2% C3A and 18% C4AF content; (b) a
binder with 10% C3A and C4AF content each. Gypsum was used as
the sulfate bearing compound, while calcium carbonate added to
differentiate the binders produced. The phases formed were identified
by XRD analysis. The results showed that ettringite was the
deterioration phase detected in the case of the low C3A content
binder. Carbonation occurred in the specimen without calcium
carbonate addition, while portlandite was observed in the one
containing calcium carbonate. In the case of the high C3A content
binder, traces of thaumasite were detected when calcium carbonate
was not incorporated in the binder. A solid solution of thaumasite and
ettringite was found when calcium carbonate was added. The amount
of C3A had not fully reacted with sulfates, since its corresponding
peaks were detected.
Abstract: This paper presents a cold flow simulation study of a small gas turbine combustor performed using laboratory scale test rig. The main objective of this investigation is to obtain physical insight of the main vortex, responsible for the efficient mixing of fuel and air. Such models are necessary for predictions and optimization of real gas turbine combustors. Air swirler can control the combustor performance by assisting in the fuel-air mixing process and by producing recirculation region which can act as flame holders and influences residence time. Thus, proper selection of a swirler is needed to enhance combustor performance and to reduce NOx emissions. Three different axial air swirlers were used based on their vane angles i.e., 30°, 45°, and 60°. Three-dimensional, viscous, turbulent, isothermal flow characteristics of the combustor model operating at room temperature were simulated via Reynolds- Averaged Navier-Stokes (RANS) code. The model geometry has been created using solid model, and the meshing has been done using GAMBIT preprocessing package. Finally, the solution and analysis were carried out in a FLUENT solver. This serves to demonstrate the capability of the code for design and analysis of real combustor. The effects of swirlers and mass flow rate were examined. Details of the complex flow structure such as vortices and recirculation zones were obtained by the simulation model. The computational model predicts a major recirculation zone in the central region immediately downstream of the fuel nozzle and a second recirculation zone in the upstream corner of the combustion chamber. It is also shown that swirler angles changes have significant effects on the combustor flowfield as well as pressure losses.