Abstract: This paper presents a resonant-based read-out circuit for capacitive pressure sensors. The proposed read-out circuit consists of an LC oscillator and a counter. The circuit detects the capacitance changes of a capacitive pressure sensor by means of frequency shifts from its nominal operation frequency. The proposed circuit is designed in 0.18 m CMOS with an estimated power consumption of 43.1mW. Simulation results show that the circuit has a capacitive resolution of 8.06kHz/fF, which enables it for high resolution pressure detection.
Abstract: The presence of a vertical edge-crack within a web
plate subjected to pure bending induces local compressive stresses
about the crack which may cause tension buckling. Approximate
theoretical expressions were derived for the critical far-field tensile
stress and bending moment capacity of an edge-cracked web plate
associated with tension buckling. These expressions were validated
with finite element analyses and used to investigate the possibility of
tension buckling in web-cracked trial girders. It was found that
tension buckling is an unlikely occurrence unless the web is relatively
thin or the crack is very long.
Abstract: A novel application of neural network approach to
fault classification and fault location of Medium voltage cables is
demonstrated in this paper. Different faults on a protected cable
should be classified and located correctly. This paper presents the use
of neural networks as a pattern classifier algorithm to perform these
tasks. The proposed scheme is insensitive to variation of different
parameters such as fault type, fault resistance, and fault inception
angle. Studies show that the proposed technique is able to offer high
accuracy in both of the fault classification and fault location tasks.
Abstract: The radius-of-curvature (ROC) defines the degree of
curvature along the centerline of a roadway whereby a travelling
vehicle must follow. Roadway designs must encompass ROC in
mitigating the cost of earthwork associated with construction while
also allowing vehicles to travel at maximum allowable design speeds.
Thus, a road will tend to follow natural topography where possible,
but curvature must also be optimized to permit fast, but safe vehicle
speeds. The more severe the curvature of the road, the slower the
permissible vehicle speed. For route planning, whether for urban
settings, emergency operations, or even parcel delivery, ROC is a
necessary attribute of road arcs for computing travel time.
It is extremely rare for a geo-spatial database to contain ROC. This
paper will present a procedure and mathematical algorithm to
calculate and assign ROC to a segment pair and/or polyline.
Abstract: In this paper, an magnetorheological (MR) mount with
fuzzy sliding mode controller (FSMC) is studied for vibration
suppression when the system is subject to base excitations. In recent
years, magnetorheological fluids are becoming a popular material in
the field of the semi-active control. However, the dynamic equation of
an MR mount is highly nonlinear and it is difficult to identify. FSMC
provides a simple method to achieve vibration attenuation of the
nonlinear system with uncertain disturbances. This method is capable
of handling the chattering problem of sliding mode control effectively
and the fuzzy control rules are obtained by using the Lyapunov
stability theory. The numerical simulations using one-dimension and
two-dimension FSMC show effectiveness of the proposed controller
for vibration suppression. Further, the well-known skyhook control
scheme and an adaptive sliding mode controller are also included in
the simulation for comparison with the proposed FSMC.
Abstract: Studies in economics domain tried to reveal the correlation between stock markets. Since the globalization era, interdependence between stock markets becomes more obvious. The Dynamic Interaction Network (DIN) algorithm, which was inspired by a Gene Regulatory Network (GRN) extraction method in the bioinformatics field, is applied to reveal important and complex dynamic relationship between stock markets. We use the data of the stock market indices from eight countries around the world in this study. Our results conclude that DIN is able to reveal and model patterns of dynamic interaction from the observed variables (i.e. stock market indices). Furthermore, it is also found that the extracted network models can be utilized to predict movement of the stock market indices with a considerably good accuracy.
Abstract: The research was designed to examine the relationship
between the development of muscle fatigue and the effect it has on
sport performance, specifically during maximal voluntary
contraction. This kind of this investigation using simultaneous
electrophysiological and mechanical recordings, based on advanced
mathematical processing, allows us to get parameters, and indexes in
a short time, and finally, the mapping to use for the thorough
investigation of the muscle contraction force, respectively the
phenomenon of local muscle fatigue, both for athletes and other
subjects.
Abstract: The ongoing effort to develop an in-house
compressible solver with multi-disciplinary physics is presented in
this paper. Basic compressible solver combined with IBM technique
provides us an effective numerical tool able to tackle the physics
phenomena and especially physic phenomena involved in Solid
Rocket Motors (SRMs). Main principles are introduced step by step
describing its implementation. This paper sheds light on the whole
potentiality of our proposed numerical model and we strongly believe
a way to introduce multi-physics mechanisms strongly coupled is
opened to ablation in nozzle, fluid/structure interaction and burning
propellant surface with time.
Abstract: Rotor Flux based Model Reference Adaptive System
(RF-MRAS) is the most popularly used conventional speed
estimation scheme for sensor-less IM drives. In this scheme, the
voltage model equations are used for the reference model. This
encounters major drawbacks at low frequencies/speed which leads to
the poor performance of RF-MRAS. Replacing the reference model
using Neural Network (NN) based flux estimator provides an
alternate solution and addresses such drawbacks. This paper
identifies an NN based flux estimator using Single Neuron Cascaded
(SNC) Architecture. The proposed SNC-NN model replaces the
conventional voltage model in RF-MRAS to form a novel MRAS
scheme named as SNC-NN-MRAS. Through simulation the proposed
SNC-NN-MRAS is shown to be promising in terms of all major
issues and robustness to parameter variation. The suitability of the
proposed SNC-NN-MRAS based speed estimator and its advantages
over RF-MRAS for sensor-less induction motor drives is
comprehensively presented through extensive simulations.
Abstract: This paper presents an optimal and unsupervised satellite image segmentation approach based on Pearson system and k-Means Clustering Algorithm Initialization. Such method could be considered as original by the fact that it utilised K-Means clustering algorithm for an optimal initialisation of image class number on one hand and it exploited Pearson system for an optimal statistical distributions- affectation of each considered class on the other hand. Satellite image exploitation requires the use of different approaches, especially those founded on the unsupervised statistical segmentation principle. Such approaches necessitate definition of several parameters like image class number, class variables- estimation and generalised mixture distributions. Use of statistical images- attributes assured convincing and promoting results under the condition of having an optimal initialisation step with appropriated statistical distributions- affectation. Pearson system associated with a k-means clustering algorithm and Stochastic Expectation-Maximization 'SEM' algorithm could be adapted to such problem. For each image-s class, Pearson system attributes one distribution type according to different parameters and especially the Skewness 'β1' and the kurtosis 'β2'. The different adapted algorithms, K-Means clustering algorithm, SEM algorithm and Pearson system algorithm, are then applied to satellite image segmentation problem. Efficiency of those combined algorithms was firstly validated with the Mean Quadratic Error 'MQE' evaluation, and secondly with visual inspection along several comparisons of these unsupervised images- segmentation.
Abstract: This paper describes identification of the two poles
unstable SOPDT process, especially with large time delay. A new
modified relay feedback identification method for two poles unstable
SOPDT process is proposed. Furthermore, for the two poles unstable
SOPDT process, an additional Derivative controller is incorporated
parallel with relay to relax the constraint on the ratio of delay to the
unstable time constant, so that the exact model parameters of
unstable processes can be identified. To cope with measurement
noise in practice, a low pass filter is suggested to get denoised output
signal toimprove the exactness of model parameter of unstable
process. PID Lead-lag tuning formulas are derived for two poles
unstable (SOPDT) processes based on IMC principle. Simulation
example illustrates the effectiveness and the simplicity of the
proposed identification and control method.
Abstract: Mycophenolic acid (MPA) is a secondary metabolite
produced by Penicillium brevicompactum, which has antibiotic and
immunosuppressive properties. In this study, the first, mycophenolic
acid was produced in a fermentation process by Penicillium
brevicompactum MUCL 19011 in shake flask using a base medium.
The maximum MPA production, product yield and productivity of
process were 1.379 g/L, 18.6 mg/g glucose and 4.9 mg/L. h,
respectively. Also the glucose consumption, biomass and MPA
production profiles were investigated during batch cultivation.
Obtained results showed that MPA production starts approximately
after 180 hours and reaches to a maximum at 280 h. In the next step,
the effects of some various concentrations of enzymatically
hydrolyzed casein on MPA production were evaluated. Maximum
MPA production, product yield and productivity as 3.63 g/L, 49
mg/g glucose and 12.96 mg/L.h, respectively were obtained with
using 30 g/L enzymatically hydrolyzed casein in culture medium.
These values show an enhanced MPA production, product yield and
process productivity pr as 116.8%, 132.8% and 163.2%, respectively.
Abstract: The purpose of this study is to reveal the principles, which have the highest impact on determining the Strategic Quality Management (SQM) implementation perceptions of managers. In order to accomplish this goal, first of all, a factor analysis is conducted on the attitudes of managers at 80 large-scale firms in Turkey for SQM principles. Secondly, utilizing t tests and discriminant analysis, the most effective items are determined. The results show that “process improvement" and “assessment of competitiveness" are the management principles, which have the highest impact on determining the SQM implementation perceptions of Turkish managers.
Abstract: In this paper, we have presented a new multivariate fuzzy time series forecasting method. This method assumes mfactors with one main factor of interest. History of past three years is used for making new forecasts. This new method is applied in forecasting total number of car accidents in Belgium using four secondary factors. We also make comparison of our proposed method with existing methods of fuzzy time series forecasting. Experimentally, it is shown that our proposed method perform better than existing fuzzy time series forecasting methods. Practically, actuaries are interested in analysis of the patterns of causalities in road accidents. Thus using fuzzy time series, actuaries can define fuzzy premium and fuzzy underwriting of car insurance and life insurance for car insurance. National Institute of Statistics, Belgium provides region of risk classification for each road. Thus using this risk classification, we can predict premium rate and underwriting of insurance policy holders.
Abstract: Unmanned Aerial Vehicles (UAVs) have gained tremendous importance, in both Military and Civil, during first decade of this century. In a UAV, onboard computer (autopilot) autonomously controls the flight and navigation of the aircraft. Based on the aircraft role and flight envelope, basic to complex and sophisticated controllers are used to stabilize the aircraft flight parameters. These controllers constitute the autopilot system for UAVs. The autopilot systems, most commonly, provide lateral and longitudinal control through Proportional-Integral-Derivative (PID) controllers or Phase-lead or Lag Compensators. Various techniques are commonly used to ‘tune’ gains of these controllers. Some techniques used are, in-flight step-by-step tuning, software-in-loop or hardware-in-loop tuning methods. Subsequently, numerous in-flight tests are required to actually ‘fine-tune’ these gains. However, an optimization-based tuning of these PID controllers or compensators, as presented in this paper, can greatly minimize the requirement of in-flight ‘tuning’ and substantially reduce the risks and cost involved in flight-testing.
Abstract: Schools today face ever-increasing demands in their attempts to ensure that students are well equipped to enter the workforce and navigate a complex world. Research indicates that computer technology can help support learning, implementation of various experiments or learning games, and that it is especially useful in developing the higher-order skills of critical thinking, observation, comprehension, implementation, comparison, analysis and active attention to activities such as research, field work, simulations and scientific inquiry. The ICT in education supports the learning procedure by enabling it to be more flexible and effective, create a rich and attractive training environment and equip the students with knowledge and potential useful for the competitive social environment in which they live. This paper presents the design, the development, and the results of the evaluation analysis of an interactive educational game which using real electric vehicles - toys (material) on a toy race track. When the game starts each student selects a specific vehicle toy. Then students are answering questionnaires in the computer. The vehicles' speed is related to the percentage of right answers in a multiple choice questionnaire (software). Every question has its own significant value depending of the different level of questionnaire. Via the developed software, each right or wrong answers in questionnaire increase or decrease the real time speed of their vehicle toys. Moreover the rate of vehicle's speed increase or decrease depends on the difficulty level of each question. The aim of the work is to attract the student’s interest in a learning process and also to improve their scores. The developed real time game was tested using independent populations of students of age groups: 8-10, 11-14, 15-18 years. Standard educational and statistical analysis tools were used for the evaluation analysis of the game. Results reveal that students using the developed real time control game scored much higher (60%) than students using a traditional simulation game on the same questionnaire. Results further indicate that student's interest in repeating the developed real time control gaming was far higher (70%) than the interest of students using a traditional simulation game.
Abstract: In order to better understand the performance of
screen channel liquid acquisition devices (LADs) in liquid oxygen (LOX), a computational fluid dynamics (CFD) simulation of LOX passing through a LAD screen channel was conducted. In the
simulation, the screen is taken as a 'porous jump' where the pressure
drop across the screen depends on the incoming velocity and is formulated by Δp = Av + Bv2
. The CFD simulation reveals the importance of the pressure losses due to the flow entering from
across the screen and impacting and merging with the channel flow
and the vortices in the channel to the cumulative flow resistance. In fact, both the flow resistance of flows impact and mergence and the
resistance created by vortices are much larger than the friction and dynamic pressure losses in the channel and are comparable to the
flow resistance across the screen. Therefore, these resistances in the
channel must be considered as part of the evaluation for the LAD
channel performance. For proper operation of a LAD in LOX these resistances must be less than the bubble point pressure for the screen
channel in LOX. The simulation also presents the pressure and velocity distributions within the LAD screen channel, expanding the understanding of the fluid flow characteristics within the channel.
Abstract: Adsorption of proteins onto a solid surface is believed to be the initial and controlling step in biofouling. A better knowledge of the fouling process can be obtained by controlling the formation of the first protein layer at a solid surface. A number of methods have been investigated to inhibit adsorption of proteins. In this study, the adsorption kinetics of
Abstract: Ants are fascinating creatures that demonstrate the
ability to find food and bring it back to their nest. Their ability as a
colony, to find paths to food sources has inspired the development of
algorithms known as Ant Colony Systems (ACS). The principle of
cooperation forms the backbone of such algorithms, commonly used
to find solutions to problems such as the Traveling Salesman
Problem (TSP). Ants communicate to each other through chemical
substances called pheromones. Modeling individual ants- ability to
manipulate this substance can help an ACS find the best solution.
This paper introduces a Dynamic Ant Colony System with threelevel
updates (DACS3) that enhance an existing ACS. Experiments
were conducted to observe single ant behavior in a colony of
Malaysian House Red Ants. Such behavior was incorporated into the
DACS3 algorithm. We benchmark the performance of DACS3 versus
DACS on TSP instances ranging from 14 to 100 cities. The result
shows that the DACS3 algorithm can achieve shorter distance in
most cases and also performs considerably faster than DACS.
Abstract: Paleoclimate was reconstructed by the clay mineral
assemblages of shale units of Pabdeh (Paleocene- Oligocene), Gurpi
(Upper Cretaceous), Kazhdumi (Albian-Cenomanian) and Gadvan
(Aptian-Neocomian) formations in the Bangestan anticline. To
compare with clay minerals assemblages in these formations,
selected samples also taken from available formations in drilled wells
in Ahvaz, Marun, Karanj, and Parsi oil fields. Collected samples
prepared using standard clay mineral methodology. They were
treated as normal, glycolated and heated oriented glass slides. Their
identification was made on X-Ray diffractographs. Illite % varies
from 8 to 36. Illite quantity increased from Pabdeh to Gurpi
Formation. This may be due to dominant dry climate. Kaolinite is in
range of 12-49%. Its variation style in different formations could be a
marker of climate changes from wet to dry which is supported by the
lithological changes. Chlorite (4-28%) can also be detected in those
samples without any kaolinite. Mixed layer minerals as the mixture
of illite-chlorite and illite-vermiculite-montmorillonite are varied
from 6 to 36%, decreased during Kazhdumi deposition from the base
to the top. This result may be according to decreasing of illite
leaching process. Vermiculite was also determined in very less
quantity and found in those units without kaolinite. Montmorillonite
varies from 8 to 43%, and its presence is due to terrestrial
depositional condition. Stratigraphical documents is also supported
this idea that clay mineral distribution is a function of the climate
changes. It seems, thus, the present results can be indicated a possible
procedure for ancient climate changes evaluation.