Abstract: In the present study the efficiency of Big Bang-Big
Crunch (BB-BC) algorithm is investigated in discrete structural
design optimization. It is shown that a standard version of the BB-BC
algorithm is sometimes unable to produce reasonable solutions to
problems from discrete structural design optimization. Two
reformulations of the algorithm, which are referred to as modified
BB-BC (MBB-BC) and exponential BB-BC (EBB-BC), are
introduced to enhance the capability of the standard algorithm in
locating good solutions for steel truss and frame type structures,
respectively. The performances of the proposed algorithms are
experimented and compared to its standard version as well as some
other algorithms over several practical design examples. In these
examples, steel structures are sized for minimum weight subject to
stress, stability and displacement limitations according to the
provisions of AISC-ASD.
Abstract: Particle damping is a technique to reduce the
structural vibrations by means of placing small metallic particles
inside a cavity that is attached to the structure at location of high
vibration amplitudes. In this paper, we have presented an analytical
model to simulate the particle damping of two dimensional transient
vibrations in structure operating under high centrifugal loads. The
simulation results show that this technique remains effective as long
as the ratio of the dynamic acceleration of the structure to the applied
centrifugal load is more than 0.1. Particle damping increases with the
increase of particle to structure mass ratio. However, unlike to the
case of particle damping in the absence of centrifugal loads where
the damping efficiency strongly depends upon the size of the cavity,
here this dependence becomes very weak. Despite the simplicity of
the model, the simulation results are considerably in good agreement
with the very scarce experimental data available in the literature for
particle damping under centrifugal loads.
Abstract: This study presents design of a carbon silicon electrode
for iontophorsis treatment towards alopecia. The alopecia is a medical
description means loss of hair from the body. For solving this problem,
the drug need to be delivered into the scalp, therefore, the
iontophoresis was chosen to use in this treatment. However, almost
common electrodes of iontophoresis device are made with metal
material, the electrodes could give patients hurt when they using it, and
it is hard to avoid the hair for attaching the hair. For this reason, an
electrode is made with silicon material to decrease the hurt from the
electrodes, and the carbon material is mixed in it for increasing
conductance. The several cones with stainless material on the
electrode make the electrode is able to void hair to attach the affected
part. According to the results of a vivo-experiment, the carbon silicon
electrode showed a good performance and in treatment comfortably.
Abstract: The purpose of suspension system in automobiles is to
improve the ride comfort and road handling. In this research the ride
and handling performance of a specific automobile with passive
suspension system is compared to a proposed fuzzy logic semi active
suspension system designed for that automobile. The bodysuspension-
wheel system is modeled as a two degree of freedom
quarter car model. MATLAB/SIMULINK [1] was used for
simulation and controller design. The fuzzy logic controller is based
on two inputs namely suspension velocity and body velocity. The
output of the fuzzy controller is the damping coefficient of the
variable damper. The result shows improvement over passive
suspension method.
Abstract: An electric utility-s main concern is to plan, design, operate and maintain its power supply to provide an acceptable level of reliability to its users. This clearly requires that standards of reliability be specified and used in all three sectors of the power system, i.e., generation, transmission and distribution. That is why reliability of a power system is always a major concern to power system planners. This paper presents the reliability analysis of Bangladesh Power System (BPS). Reliability index, loss of load probability (LOLP) of BPS is evaluated using recursive algorithm and considering no de-rated states of generators. BPS has sixty one generators and a total installed capacity of 5275 MW. The maximum demand of BPS is about 5000 MW. The relevant data of the generators and hourly load profiles are collected from the National Load Dispatch Center (NLDC) of Bangladesh and reliability index 'LOLP' is assessed for the period of last ten years.
Abstract: Synchronous cooperative systems (SCS) bring together users that are geographically distributed and connected through a network to carry out a task. Examples of SCS include Tele- Immersion and Tele-Conferences. In SCS, the coordination is the core of the system, and it has been defined as the act of managing interdependencies between activities performed to achieve a goal. Some of the main problems that SCS present deal with the management of constraints between simultaneous activities and the execution ordering of these activities. In order to resolve these problems, orderings based on Lamport-s happened-before relation have been used, namely, causal, Δ-causal, and causal-total orderings. They mainly differ in the degree of asynchronous execution allowed. One of the most important orderings is the causal order, which establishes that the events must be seen in the cause-effect order as they occur in the system. In this paper we show that for certain SCS (e.g. videoconferences, tele-immersion) where some degradation of the system is allowed, ensuring the causal order is still rigid, which can render negative affects to the system. In this paper, we illustrate how a more relaxed ordering, which we call Fuzzy Causal Order (FCO), is useful for such kind of systems by allowing a more asynchronous execution than the causal order. The benefit of the FCO is illustrated by applying it to a particular scenario of intermedia synchronization of an audio-conference system.
Abstract: The purpose of the study is to determine secondary prospective mathematics teachers- views related to using flash animations in mathematics lessons and to reveal how the sample presentations towards different mathematical concepts altered their views. This is a case study involving three secondary prospective mathematics teachers from a state university in Turkey. The data gathered from two semi-structural interviews. Findings revealed that these animations help understand mathematics meaningfully, relate mathematics and real world, visualization, and comprehend the importance of mathematics. The analysis of the data indicated that the sample presentations enhanced participants- views about using flash animations in mathematics lessons.
Abstract: Overhead electrical insulators form an important link in an electric power system. Along with the traditional insulators (i.e. glass and porcelain, etc) presently the polymeric insulators are also used world widely. These polymeric insulators are very sensitive to various environmental parameters such temperature, environmental pollution, UV-radiations, etc. which seriously effect their electrical, chemical and hydrophobic properties. The UV radiation level in the central region of Saudi Arabia is high as compared to the IEC standard for the accelerated aging of the composite insulators. Commonly used suspension type of composite EPDM (Ethylene Propylene Diene Monomer) insulator was subjected to accelerated stress aging as per modified IEC standard simulating the inland arid deserts atmospheric condition and also as per IEC-61109 standard. The hydrophobic characteristics were studied by measuring the contact angle along the insulator surface before and after the accelerated aging of the samples. It was found that EPDM insulator loses it hydrophobic properties proportional to the intensity of UV irradiations and its rate of recovery is also very low as compared to Silicone Rubber insulator.KeywordsEPDM, composite insulators, accelerated aging, hydrophobicity, contact angle.
Abstract: Reliable water level forecasts are particularly
important for warning against dangerous flood and inundation. The
current study aims at investigating the suitability of the adaptive
network based fuzzy inference system for continuous water level
modeling. A hybrid learning algorithm, which combines the least
square method and the back propagation algorithm, is used to
identify the parameters of the network. For this study, water levels
data are available for a hydrological year of 2002 with a sampling
interval of 1-hour. The number of antecedent water level that should
be included in the input variables is determined by two statistical
methods, i.e. autocorrelation function and partial autocorrelation
function between the variables. Forecasting was done for 1-hour until
12-hour ahead in order to compare the models generalization at
higher horizons. The results demonstrate that the adaptive networkbased
fuzzy inference system model can be applied successfully and
provide high accuracy and reliability for river water level estimation.
In general, the adaptive network-based fuzzy inference system
provides accurate and reliable water level prediction for 1-hour ahead
where the MAPE=1.15% and correlation=0.98 was achieved. Up to
12-hour ahead prediction, the model still shows relatively good
performance where the error of prediction resulted was less than
9.65%. The information gathered from the preliminary results
provide a useful guidance or reference for flood early warning
system design in which the magnitude and the timing of a potential
extreme flood are indicated.
Abstract: According to previous studies, some muscles present a non-homogeneous spatial distribution of its muscle fiber types and motor unit types. However, available muscle models only deal with muscles with homogeneous distributions. In this paper, a new architecture muscle model is proposed to permit the construction of non-uniform distributions of muscle fibers within the muscle cross section. The idea behind is the use of a motor unit placement algorithm that controls the spatial overlapping of the motor unit territories of each motor unit type. Results show the capabilities of the new algorithm to reproduce arbitrary muscle fiber type distributions.
Abstract: An explicit axisymmetrical FE methodology is
developed here to study the particle temperature arising in WC-Co
particle on an AISI 1045 steel substrate. Parameters of constitutive
Johnson-cook model were used for simulation. The results show that
particle velocity and kinetic energy have important role in
temperature arising of particles.
Abstract: The activities of alkaline phosphatase and Ca2+ATPase in mud crab (Scylla serrata) collected from a soft-shell crab farm in Chantaburi Province, Thailand, in several stages of molting cycle were observed. The results showed that the activity of alkaline phosphatase in gill after molting was highly significant (p
Abstract: Natural fibres have emerged as the potential reinforcement material for composites and thus gain attraction by many researchers. This is mainly due to their applicable benefits as they offer low density, low cost, renewable, biodegradability and environmentally harmless and also comparable mechanical properties with synthetic fibre composites. The properties of hybrid composites highly depends on several factors, including the interaction of fillers with the polymeric matrix, shape and size (aspect ratio), and orientation of fillers [1]. In this study, natural fibre kenaf composites and kenaf/fibreglass hybrid composites were fabricated by a combination of hand lay-up method and cold-press method. The effect of different fibre types (powder, short and long) on the tensile properties of composites is investigated. The kenaf composites with and without the addition of fibreglass were then characterized by tensile testing and scanning electron microscopy. A significant improvement in tensile strength and modulus were indicated by the introduction of long kenaf/woven fibreglass hybrid composite. However, the opposite trends are observed in kenaf powder composite. Fractographic observation shows that fibre/matrix debonding causes the fibres pull out. This phenomenon results in the fibre and matrix fracture.
Abstract: Enzymatic hydrolysis is one of the major steps involved in the conversion from sugarcane bagasse to yield ethanol. This process offers potential for yields and selectivity higher, lower energy costs and milder operating conditions than chemical processes. However, the presence of some factors such as lignin content, crystallinity degree of the cellulose, and particle sizes, limits the digestibility of the cellulose present in the lignocellulosic biomasses. Pretreatment aims to improve the access of the enzyme to the substrate. In this study sugarcane bagasse was submitted chemical pretreatment that consisted of two consecutive steps, the first with dilute sulfuric acid (1 % (v/v) H2SO4), and the second with alkaline solutions with different concentrations of NaOH (1, 2, 3 and 4 % (w/v)). Thermal Analysis (TG/ DTG and DTA) was used to evaluate hemicellulose, cellulose and lignin contents in the samples. Scanning Electron Microscopy (SEM) was used to evaluate the morphological structures of the in natura and chemically treated samples. Results showed that pretreatments were effective in chemical degradation of lignocellulosic materials of the samples, and also was possible to observe the morphological changes occurring in the biomasses after pretreatments.
Abstract: Image Edge Detection is one of the most important
parts of image processing. In this paper, by fuzzy technique, a new
method is used to improve digital image edge detection. In this
method, a 3x3 mask is employed to process each pixel by means of
vicinity. Each pixel is considered a fuzzy input and by examining
fuzzy rules in its vicinity, the edge pixel is specified and by utilizing
calculation algorithms in image processing, edges are displayed more
clearly. This method shows significant improvement compared to
different edge detection methods (e.g. Sobel, Canny).
Abstract: Maximal length sequences (m-sequences) are also
known as pseudo random sequences or pseudo noise sequences
for closely following Golomb-s popular randomness properties: (P1)
balance, (P2) run, and (P3) ideal autocorrelation. Apart from these,
there also exist certain other less known properties of such sequences
all of which are discussed in this tutorial paper. Comprehensive proofs
to each of these properties are provided towards better understanding
of such sequences. A simple test is also proposed at the end of
the paper in order to distinguish pseudo noise sequences from truly
random sequences such as Bernoulli sequences.
Abstract: Any use of energy in industrial productive activities is combined with various environment impacts. Withintransportation,
this fact was not only found among land transport, railways and maritime transport, but also in the air transport industry. An effective climate protection requires strategies and measures for reducing all
greenhouses gas emissions, in particular carbon dioxide, and must
take into account the economic, ecologic and social aspects. It seem simperative now to develop and manufacture environmentally
friendly products and systems, to reduce consumption and use less
resource, and to save energy and power. Today-sproducts could
better serve these requirements taking into account the integration of
a power management system into the electrical power system.This
paper gives an overview of an approach ofpower management with
load prioritization in modernaircraft. Load dimensioning and load
management strategies on current civil aircraft will be presented and
used as a basis for the proposed approach.
Abstract: We show that in a two-channel sampling series expansion
of band-pass signals, any finitely many missing samples can
always be recovered via oversampling in a larger band-pass region.
We also obtain an analogous result for multi-channel oversampling
of harmonic signals.
Abstract: Energy efficiency is the key requirement in wireless sensor network as sensors are small, cheap and are deployed in very large number in a large geographical area, so there is no question of replacing the batteries of the sensors once deployed. Different ways can be used for efficient energy transmission including Multi-Hop algorithms, collaborative communication, cooperativecommunication, Beam- forming, routing algorithm, phase, frequency and time synchronization. The paper reviews the need for time synchronization and proposed a BFS based synchronization algorithm to achieve energy efficiency. The efficiency of our protocol has been tested and verified by simulation
Abstract: In this paper the principle, basic torque theory and design optimisation of a six-phase reluctance dc machine are considered. A trapezoidal phase current waveform for the machine drive is proposed and evaluated to minimise ripple torque. Low cost normal laminated salient-pole rotors with and without slits and chamfered poles are investigated. The six-phase machine is optimised in multi-dimensions by linking the finite-element analysis method directly with an optimisation algorithm; the objective function is to maximise the torque per copper losses of the machine. The armature reaction effect is investigated in detail and found to be severe. The measured and calculated torque performances of a 35 kW optimum designed six-phase reluctance dc machine drive are presented.