Abstract: As wireless sensor networks are energy constraint networks
so energy efficiency of sensor nodes is the main design issue.
Clustering of nodes is an energy efficient approach. It prolongs the
lifetime of wireless sensor networks by avoiding long distance communication.
Clustering algorithms operate in rounds. Performance of
clustering algorithm depends upon the round time. A large round
time consumes more energy of cluster heads while a small round
time causes frequent re-clustering. So existing clustering algorithms
apply a trade off to round time and calculate it from the initial
parameters of networks. But it is not appropriate to use initial
parameters based round time value throughout the network lifetime
because wireless sensor networks are dynamic in nature (nodes can be
added to the network or some nodes go out of energy). In this paper
a variable round time approach is proposed that calculates round
time depending upon the number of active nodes remaining in the
field. The proposed approach makes the clustering algorithm adaptive
to network dynamics. For simulation the approach is implemented
with LEACH in NS-2 and the results show that there is 6% increase
in network lifetime, 7% increase in 50% node death time and 5%
improvement over the data units gathered at the base station.
Abstract: Deep cold rolling (DCR) and low plasticity burnishing (LPB) process are cold working processes, which easily produce a smooth and work-hardened surface by plastic deformation of surface irregularities. The present study focuses on the surface roughness and surface hardness aspects of AISI 4140 work material, using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in order to identify the predominant factors amongst the selected parameters. They were then categorized in order of significance followed by setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. In the present work, the influence of main process parameters (force, feed rate, number of tool passes/overruns, initial roughness of the work piece, ball material, ball diameter and lubricant used) on the surface roughness and the hardness of AISI 4140 steel were studied for both LPB and DCR process and the results are compared. It was observed that by using LPB process surface hardness has been improved by 167% and in DCR process surface hardness has been improved by 442%. It was also found that the force, ball diameter, number of tool passes and initial roughness of the workpiece are the most pronounced parameters, which has a significant effect on the work piece-s surface during deep cold rolling and low plasticity burnishing process.
Abstract: The continued interest in the use of distributed generation in recent years is leading to the growth in number of distributed generators connected to distribution networks. Steady state voltage rise resulting from the connection of these generators can be a major obstacle to their connection at lower voltage levels. The present electric distribution network is designed to keep the customer voltage within tolerance limit. This may require a reduction in connectable generation capacity, under utilization of appropriate generation sites. Thus distribution network operators need a proper voltage regulation method to allow the significant integration of distributed generation systems to existing network. In this work a voltage rise problem in a typical distribution system has been studied. A method for voltage regulation of distribution system with multiple DG system by coordinated operation distributed generator, capacitor and OLTC has been developed. A sensitivity based analysis has been carried out to determine the priority for individual generators in multiple DG environment. The effectiveness of the developed method has been evaluated under various cases through simulation results.
Abstract: In this paper we present two novel 1-bit full adder
cells in dynamic logic style. NP-CMOS (Zipper) and Multi-Output
structures are used to design the adder blocks. Characteristic of
dynamic logic leads to higher speeds than the other standard static
full adder cells. Using HSpice and 0.18┬Ám CMOS technology
exhibits a significant decrease in the cell delay which can result in a
considerable reduction in the power-delay product (PDP). The PDP
of Multi-Output design at 1.8v power supply is around 0.15 femto
joule that is 5% lower than conventional dynamic full adder cell and
at least 21% lower than other static full adders.
Abstract: In order to calculate the flexural strength of
normal-strength concrete (NSC) beams, the nonlinear actual concrete
stress distribution within the compression zone is normally replaced
by an equivalent rectangular stress block, with two coefficients of α
and β to regulate the intensity and depth of the equivalent stress
respectively. For NSC beams design, α and β are usually assumed
constant as 0.85 and 0.80 in reinforced concrete (RC) codes. From an
earlier investigation of the authors, α is not a constant but significantly
affected by flexural strain gradient, and increases with the increasing
of strain gradient till a maximum value. It indicates that larger
concrete stress can be developed in flexure than that stipulated by
design codes. As an extension and application of the authors- previous
study, the modified equivalent concrete stress block is used here to
produce a series of design charts showing the maximum design limits
of flexural strength and ductility of singly- and doubly- NSC beams,
through which both strength and ductility design limits are improved
by taking into account strain gradient effect.
Abstract: This paper identifies five key design characteristics of
production scheduling software systems in printed circuit board (PCB) manufacturing. The authors consider that, in addition to an effective scheduling engine, a scheduling system should be able to
process a preventative maintenance calendar, to give the user the
flexibility to handle data using a variety of electronic sources, to run
simulations to support decision-making, and to have simple and
customisable graphical user interfaces. These design considerations
were the result of a review of academic literature, the evaluation of
commercial applications and a compilation of requirements of a PCB manufacturer. It was found that, from those systems that were evaluated, those that effectively addressed all five characteristics
outlined in this paper were the most robust of all and could be used in
PCB manufacturing.
Abstract: This paper focuses on the 3D reconstruction of
the architectural design of Darul Ridzuan Museum. It has
concentrated on designing exterior part of the building according
to colored digital photo of the real museum. Besides viewing the
architecture, walkthroughs are generated for the user to control
it in an easier way. User can travel through the museum to get
the feel of the environment and to explore the design of the
museum as a whole; both exterior and interior. The result has
shown positive result in terms of realism, navigation, collision
detection, suitability, usability and user-s acceptance. In brief,
the 3D virtual museum has provided an alternative to present a
real museum.
Abstract: Application of wood in rural construction is diffused
all around the world since remote times. However, its inclusion in
structural design deserves strong support from broad knowledge of
material properties. The pertinent literature reveals the application of
optical methods in determining the complete field displacement on
bodies exhibiting regular as well as irregular surfaces. The use of
moiré techniques in experimental mechanics consists in analyzing the
patterns generated on the body surface before and after deformation.
The objective of this research work is to study the qualitative
deformation behavior of wooden testing specimens under specific
loading situations. The experiment setup follows the literature
description of shadow moiré methods. Results indicate strong
anisotropy influence of the generated displacement field. Important
qualitative as well as quantitative stress and strain distribution were
obtained wooden members which are applicable to rural
constructions.
Abstract: Construction of tunnels is connected with high
uncertainty in the field of costs, construction period, safety and
impact on surroundings. Risk management became therefore a
common part of tunnel projects, especially after a set of fatal
collapses occurred in 1990's. Such collapses are caused usually by
combination of factors that can be divided into three main groups, i.e.
unfavourable geological conditions, failures in the design and
planning or failures in the execution.
This paper suggests a procedure enabling quantification of the
excavation risk related to extraordinary accidents using FTA and
ETA tools. It will elaborate on a common process of risk analysis and
enable the transfer of information and experience between particular
tunnel construction projects. Further, it gives a guide for designers,
management and other participants, how to deal with risk of such
accidents and how to make qualified decisions based on a
probabilistic approach.
Abstract: Short circuit currents plays a vital role in influencing the design and operation of equipment and power system and could not be avoided despite careful planning and design, good maintenance and thorough operation of the system. This paper discusses the short circuit analysis conducted in KSO briefly comprising of its significances, methods and results. A result sample of the analysis based on a single transformer is detailed in this paper. Furthermore, the results of the analysis and its significances were also discussed and commented.
Abstract: Phase locked loops for data links operating at 10 Gb/s
or faster are low phase noise devices designed to operate with a low
jitter reference clock. Characterization of their jitter transfer function
is difficult because the intrinsic noise of the device is comparable to
the random noise level in the reference clock signal. A linear model
is proposed to account for the intrinsic noise of a PLL. The intrinsic
noise data of a PLL for 10 Gb/s links is presented. The jitter transfer
function of a PLL in a test chip for 12.8 Gb/s data links was
determined in experiments using the 400 MHz reference clock as the
source of simultaneous excitations over a wide range of frequency.
The result shows that the PLL jitter transfer function can be
approximated by a second order linear model.
Abstract: In the past years a lot of effort has been made in the
field of face detection. The human face contains important features
that can be used by vision-based automated systems in order to
identify and recognize individuals. Face location, the primary step of
the vision-based automated systems, finds the face area in the input
image. An accurate location of the face is still a challenging task.
Viola-Jones framework has been widely used by researchers in order
to detect the location of faces and objects in a given image. Face
detection classifiers are shared by public communities, such as
OpenCV. An evaluation of these classifiers will help researchers to
choose the best classifier for their particular need. This work focuses
of the evaluation of face detection classifiers minding facial
landmarks.
Abstract: Power-line networks are widely used today for broadband data transmission. However, due to multipaths within the broadband power line communication (BPLC) systems owing to stochastic changes in the network load impedances, branches, etc., network or channel capacity performances are affected. This paper attempts to investigate the performance of typical medium voltage channels that uses Orthogonal Frequency Division Multiplexing (OFDM) techniques with Quadrature Amplitude Modulation (QAM) sub carriers. It has been observed that when the load impedances are different from line characteristic impedance channel performance decreases. Also as the number of branches in the link between the transmitter and receiver increases a loss of 4dB/branch is found in the signal to noise ratio (SNR). The information presented in the paper could be useful for an appropriate design of the BPLC systems.
Abstract: Connected dominating set (CDS) problem in unit disk
graph has signi£cant impact on an ef£cient design of routing protocols
in wireless sensor networks, where the searching space for a
route is reduced to nodes in the set. A set is dominating if all the
nodes in the system are either in the set or neighbors of nodes in the
set. In this paper, a simple and ef£cient heuristic method is proposed
for £nding a minimum connected dominating set (MCDS) in ad hoc
wireless networks based on the new parameter support of vertices.
With this parameter the proposed heuristic approach effectively
£nds the MCDS of a graph. Extensive computational experiments
show that the proposed approach outperforms the recently proposed
heuristics found in the literature for the MCD
Abstract: The paper proposes an approach for design of modular
systems based on original technique for modeling and formulation of
combinatorial optimization problems. The proposed approach is
described on the example of personal computer configuration design.
It takes into account the existing compatibility restrictions between
the modules and can be extended and modified to reflect different
functional and users- requirements. The developed design modeling
technique is used to formulate single objective nonlinear mixedinteger
optimization tasks. The practical applicability of the
developed approach is numerically tested on the basis of real modules
data. Solutions of the formulated optimization tasks define the
optimal configuration of the system that satisfies all compatibility
restrictions and user requirements.
Abstract: The effect of cassava root ensiled with cassava top or
legumes on voluntary feed intake and milk production were
determined in 12 dairy cows using a 4×3 change-over design.
Experimental period were 30 days long and consisted of 14 days of
adaptation. Silage was prepared from cassava root mixed with
cassava top or legumes at ratio 60:40. Cows were allotted at random
to receive ad libitum one of four rations: T1) control, T2) cassava
root +cassava top-silages, T3) cassava root +hamata - silages and T4)
cassava root +Thapra stylo-silages.
The dry matter intake (BW0.75) was higher (P< 0.05) in cow fed
with silages diets compared with T1. However, the intake of T2 was
higher among treatments. Milk production was lowest in cow fed
with T1. Among silages based diets, milk production was not
significantly different but 4%FCM was higher in cow fed T2. Milk
compositions were not affected by feeding diets.
It is concluded that feeding cassava root ensiled with its leaves as
a supplement increased dry matter intake and significantly improved
4%FCM. The combination of cassava root and legume silages did not
improve the feed intake but did increase the milk production.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetically and thermal stresses remain major failures
for insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: We demonstrate through a sample application, Ebanking,
that the Web Service Modelling Language Ontology component
can be used as a very powerful object-oriented database design
language with logic capabilities. Its conceptual syntax allows the
definition of class hierarchies, and logic syntax allows the definition
of constraints in the database. Relations, which are available for
modelling relations of three or more concepts, can be connected to
logical expressions, allowing the implicit specification of database
content. Using a reasoning tool, logic queries can also be made
against the database in simulation mode.
Abstract: The research study is carried out to determine the efficiency of the Biofilm sewage treatment plant which is located at the Engineering Complex-s. Wastewater analyses have been carried out at the Environmental Engineering laboratory to study the six parameters: Biochemical Oxygen Demand BOD, Chemical Oxygen Demand COD l, and Total Suspended Solids TSS, Ammoniac Nitrogen NH3-N and Phosphorous P which have been selected to determine the wastewater quality. The plant was designed to treat 750 Pe (population equivalent) at hydraulic retention time of 5 hours in the aerobic zone. The results show that Biofilm wastewater treatment plant was able to treat sewage successfully at different flow condition. The discharge has fulfilled the Malaysia Environmental of Standard A water quality. The achieved BOD removal is more than 85%, COD is more than 80%, TSS is more than 80%, NH3-N is more than 70%, and P was more than 70%. The Biofilm system provides a very efficient process for sewage treatment and it is compact in structure thus minimizes the required land area.
Abstract: Interactive public displays give access as an
innovative media to promote enhanced communication between
people and information. However, digital public displays are subject
to a few constraints, such as content presentation. Content
presentation needs to be developed to be more interesting to attract
people’s attention and motivate people to interact with the display. In
this paper, we proposed idea to implement contents with interaction
elements for vision-based digital public display. Vision-based
techniques are applied as a sensor to detect passers-by and theme
contents are suggested to attract their attention for encouraging them
to interact with the announcement content. Virtual object, gesture
detection and projection installation are applied for attracting
attention from passers-by. Preliminary study showed positive
feedback of interactive content designing towards the public display.
This new trend would be a valuable innovation as delivery of
announcement content and information communication through this
media is proven to be more engaging.