Abstract: Extraction of Fe(III) from aqueous solution using Trin-
butyl Phosphate (TBP) as carrier needs a highly acidic medium
(>6N) as it favours formation of chelating complex FeCl3.TBP.
Similarly, stripping of Iron(III) from loaded organic solvents requires
neutral pH or alkaline medium to dissociate the same complex. It is
observed that TBP co-extracts acids along with metal, which causes
reversal of driving force of extraction and iron(III) is re-extracted
back from the strip phase into the feed phase during Liquid Emulsion
Membrane (LEM) pertraction. Therefore, rate of extraction of
different mineral acids (HCl, HNO3, H2SO4) using TBP with and
without presence of metal Fe(III) was examined. It is revealed that in
presence of metal acid extraction is enhanced. Determination of mass
transfer coefficient of both acid and metal extraction was performed
by using Bulk Liquid Membrane (BLM). The average mass transfer
coefficient was obtained by fitting the derived model equation with
experimentally obtained data. The mass transfer coefficient of the
mineral acid extraction is in the order of kHNO3 = 3.3x10-6m/s > kHCl =
6.05x10-7m/s > kH2SO4 = 1.85x10-7m/s. The distribution equilibria of
the above mentioned acids between aqueous feed solution and a
solution of tri-n-butyl-phosphate (TBP) in organic solvents have been
investigated. The stoichiometry of acid extraction reveals the
formation of TBP.2HCl, HNO3.2TBP, and TBP.H2SO4 complexes.
Moreover, extraction of Iron(III) by TBP in HCl aqueous solution
forms complex FeCl3.TBP.2HCl while in HNO3 medium forms
complex 3FeCl3.TBP.2HNO3
Abstract: The antioxidant capability of beverage blends made from cocoa, zobo and ginger with standard antioxidant assay procedures was investigated. The DPPH (2,2-diphenyl-1- picrylhydrazyl) scavenging capacity ranged from 21.2-25.8% in comparison with GSH of 37.1%. The ferric reducing ability was highest in the zobo drink and lowest in ginger. The superoxide scavenging capacity was also highest in the zobo drink followed by the drink with alkalized cocoa. The metal chelating power decreased as the level of zobo in the blends decreases. The chelating power of zobo and ginger were significantly lower than the natural and alkalized cocoa. The 100% zobo drink inhibited linoleic acid till the fifth day while natural and alkalized cocoa as well as the blend with 50% alkalized cocoa inhibited linoleic acid greatly till the sixth day. The finding describes the potential health benefit of the phytochemical antioxidants of cocoa:zobo:ginger beverage blends.
Abstract: α-Pinene is the main component of the most
turpentine oils. The hydration of α-pinene with acid catalysts leads to
a complex mixture of monoterpenes. In order to obtain more valuable
products, the α-pinene in the turpentine can be hydrated in dilute
mineral acid solutions to produce α-terpineol. The design of
separation processes requires information on phase equilibrium and
related thermodynamic properties. This paper reports the results of
study on liquid-liquid equilibrium (LLE) of system containing α-
pinene + water and α-terpineol + water.
Binary LLE for α-pinene + water system, and α-terpineol + water
systems were determined by experiment at 301K and atmospheric
pressure. The two component mixture was stirred for about 30min,
then the mixture was left for about 2h for complete phase separation.
The composition of both phases was analyzed by using a Gas
Chromatograph. The experimental data were correlated by
considering both NRTL and UNIQUAC activity coefficient models.
The LLE data for the system of α-pinene + water and α-terpineol +
water were correlated successfully by the NRTL model. The
experimental data were not satisfactorily fitted by the UNIQUAC
model. The NRTL model (α =0.3) correlates the LLE data for the
system of α-pinene + water at 301K with RMSD of 0.0404%. And
the NRTL model (α =0.61) at 301K with RMSD of 0.0058 %. The
NRTL model (α =0.3) correlates the LLE data for the system of α-
terpineol + water at 301K with RMSD of 0.1487% and the NRTL
model (α =0.6) at 301K with RMSD of 0.0032%, between the
experimental and calculated mole fractions.
Abstract: Zinc oxide thin films with various microstructures
were grown on substrates by using HCOOH-sols. The reaction
mechanism of the sol system was investigated by performing an XPS
analysis of as-synthesized films, due to the products of hydrolysis
and condensation in the sol system contributing to the chemical state
of the as-synthesized films. The chemical structures of the assynthesized
films related to the microstructures of the final annealed
films were also studied. The results of the Zn 2p3/2, C 1s and O1s
XPS patterns indicate that the hydrolysis reaction in the sol system is
strongly influenced by the HCOOH agent. The results of XRD and
FE-SEM demonstrated the microstructures of the annealed films are
related to the content of hydrolyzed zinc hydrate (Zn-OH) species
present, and that content of the Zn-OH species in the sol system
increases the HCOOH adding, and these Zn-OH species existing in
the sol phase are responsible for large ZnO crystallites in the final
annealed films.
Abstract: Pretreatment is an essential step in the conversion of
lignocellulosic biomass to fermentable sugar that used for biobutanol
production. Among pretreatment processes, microwave is considered
to improve pretreatment efficiency due to its high heating efficiency,
easy operation, and easily to combine with chemical reaction. The
main objectives of this work are to investigate the feasibility of
microwave pretreatment to enhance enzymatic hydrolysis of
corncobs and to determine the optimal conditions using response
surface methodology. Corncobs were pretreated via two-stage
pretreatment in dilute sodium hydroxide (2 %) followed by dilute
sulfuric acid 1 %. Pretreated corncobs were subjected to enzymatic
hydrolysis to produce reducing sugar. Statistical experimental design
was used to optimize pretreatment parameters including temperature,
residence time and solid-to-liquid ratio to achieve the highest amount
of glucose. The results revealed that solid-to-liquid ratio and
temperature had a significant effect on the amount of glucose.
Abstract: In this article, we synthesize a novel chitosan -based
superabsorbent hydrogel via graft copolymerization of mixtures
acrylic acid (AA) and N-vinyl pyrollidon onto chitosan backbones.
The polymerization reaction was carried out in an aqueous medium
and in the presence of ammonium persulfate (APS) as an initiator and
N,N'-methylene bisacrylamide (MBA) as a crosslinker.The hydrogel
structures were confirmed by FTIR spectroscopy. The swelling
behavior of these absorbent polymers was also investigated in
various salt solutions. Results indicated that the swelling capacity
decreased with an increase in the ionic strength of the swelling
medium. Furthermore, the swelling of superabsorbing hydrogels was
examined in solutions with pH values ranging between 1.0 and 13.0.
It showed a reversible pH-responsive behavior at pHs 2.0 and 8.0.
This on-off switching behavior makes the synthesized hydrogels as
an excellent candidate for controlled delivery of bioactive agents.
Abstract: In this study, structural, mechanical, thermal and
electrical properties of poly (lactic acid) (PLA) nanocomposites with
low-loaded (0-1.5 wt%) untreated, heat and nitric acid treated multiwalled
carbon nanotubes (MWCNTs) were studied. Among the
composites, untreated 0.5 wt % MWCNTs and acid-treated 1.0 wt%
MWCNTs reinforced PLA show the tensile strength and modulus
values higher than the others. These two samples along with pure
PLA exhibit the stable orthorhombic α-form, whilst other samples
reveal the less stable orthorhombic β-form, as demonstrated by X-ray
diffraction study. Differential scanning calorimetry reveals the
evolution of the mentioned different phases by controlled cooling and
discloses an enhancement of PLA crystallization by nanotubes
incorporation. Thermogravimetric analysis shows that the MWCNTs
loaded sample degraded faster than PLA. Surface resistivity of the
nanocomposites is found to be dropped drastically by a factor of 1013
with a low loading of MWCNTs (1.5 wt%).
Abstract: Theexperiment was carried out with 2x5 male Merino
lambs raised under intensive conditions to investigate the effect of
dietary calcium soap of linseed oil on the color and fatty acid
composition of longissimusdorsi muscle. Control lambs fed a basal
diet and the experimental lambs consumed a diet supplemented with
3% calcium soap of linseed oil. The color values (L*, a*, b* a*/b*
and chroma) were not influenced by dietary treatment. The MUFA
proportion reduced, SFA and PUFA content did not alter. As
expected, the linolenic (C18:3 n3) and thusthe n-3 content
significantly improved by linseed supplement (0.47 and 0.81; 0.78
and 1.16 in control and in experimental samples, respectively). Other
n-3 and n-6 fatty acids had similar valuestocontrol samples. The n-
6/n-3 ratio was significantly narrower in the experimental group (6.31
vs. 9.38) but the P/S ratio did not differ betweenthe two groups.In
conclusion calcium soap of linseed oil seems to be a suitable
supplement form of n-3 fatty acids to improve the nutritive value of
lamb meat.
Abstract: Trace element speciation of an integrated soil
amendment matrix was studied with a modified BCR sequential
extraction procedure. The analysis included pseudo-total
concentration determinations according to USEPA 3051A and
relevant physicochemical properties by standardized methods. Based
on the results, the soil amendment matrix possessed neutralization
capacity comparable to commercial fertilizers. Additionally, the
pseudo-total concentrations of all trace elements included in the
Finnish regulation for agricultural fertilizers were lower than the
respective statutory limit values. According to chemical speciation,
the lability of trace elements increased in the following order: Hg <
Cr < Co < Cu < As < Zn < Ni < Pb < Cd < V < Mo < Ba. The
validity of the BCR approach as a tool for chemical speciation was
confirmed by the additional acid digestion phase. Recovery of trace
elements during the procedure assured the validity of the approach
and indicated good quality of the analytical work.
Abstract: The Iranian bentonite was first characterized by
Scanning Electron Microscopy (SEM), Inductively Coupled Plasma
mass spectrometry (ICP-MS), X-ray fluorescence (XRF), X-ray
Diffraction (XRD) and BET. The bentonite was then treated
thermally between 150°C-250°C at 15min, 45min and 90min and
also was activated chemically with different concentration of
sulphuric acid (3N, 5N and 10N). Although the results of thermal
activated-bentonite didn-t show any considerable changes in specific
surface area and Cation Exchange Capacity (CEC), but the results of
chemical treated bentonite demonstrated that such properties have
been improved by acid activation process.
Abstract: The morphology, mineralogical and chemical
composition of a low-grade nickel ore from Mpumalanga, South
Africa, were studied by scanning electron microscope (SEM), X-ray
diffraction (XRD) and X-ray fluorescence (XRF), respectively. The
ore was subjected to atmospheric agitation leaching using sulphuric
acid to investigate the effects of acid concentration, leaching
temperature, leaching time and particle size on extraction of nickel
and cobalt. Analyses results indicated the ore to be a saprolitic nickel
laterite belonging to the serpentine group of minerals. Sulphuric acid
was found to be able to extract nickel from the ore. Increased acid
concentration and temperature only produced low amounts of nickel
but improved cobalt extraction. As high as 77.44% Ni was achieved
when leaching a -106+75μm fraction with 4.0M acid concentration at
25oC. The kinetics of nickel leaching from the saprolitic ore were
studied and the activation energy was determined to be 18.16kJ/mol.
This indicated that nickel leaching reaction was diffusion controlled.
Abstract: The Deoxyribonucleic Acid (DNA) which is a doublestranded helix of nucleotides consists of: Adenine (A), Cytosine (C), Guanine (G) and Thymine (T). In this work, we convert this genetic code into an equivalent digital signal representation. Applying a wavelet transform, such as Haar wavelet, we will be able to extract details that are not so clear in the original genetic code. We compare between different organisms using the results of the Haar wavelet Transform. This is achieved by using the trend part of the signal since the trend part bears the most energy of the digital signal representation. Consequently, we will be able to quantitatively reconstruct different biological families.
Abstract: Tumor cells have an invasive and metastatic phenotype
that is the main cause of death for cancer patients. Tumor
establishment and penetration consists of a series of complex
processes involving multiple changes in gene expression. In this study,
intraperitoneal administration of a high concentration of ascorbic acid
inhibited tumor establishment and decreased tumor mass in BALB/C
mice implanted with S-180 sarcoma cancer cells. To identify proteins
involved in the ascorbic acid-mediated inhibition of tumor
progression, changes in the tumor proteome associated with ascorbic
acid treatment of BALB/C mice implanted with S-180 were
investigated using two-dimensional gel electrophoresis and mass
spectrometry. Twenty protein spots were identified whose expression
was different between control and ascorbic acid treatment groups.
Abstract: Phytases are acid phosphatase enzymes, which
efficiently cleave phosphate moieties from phytic acid, thereby
generating myo-inositol and inorganic phosphate. Thirty four
isolates of endophytic fungi to produce of phytases were isolated
from leaf, stem and root fragments of soybean. Screening of 34
isolates of endophytic fungi identified the phytases produced by
Rhizoctonia sp. and Fusarium verticillioides . The phytase
production were the best induced by phytic acid and rice bran
compared the others inducer in submerged fermentation medium
used. The phytase produced by both Rhizoctonia sp. and F.
verticillioides have pH optimum at 4.0 and 5.0 respectively. The
characterization of phytase from Fusarium verticillioides showed that
temperature optimum was 500C and stability until 600C, the pH
optimum 5.0 and pH stability was 2.5 – 6.0, and substrate specificity
were rice bran>soybean meal>corn> coconut cake, respectively.
Abstract: Langmuir–Blodgett (LB) films of polyaniline (PANI) grown onto ITO coated glass substrates were utilized for the fabrication of Uric acid biosensor for efficient detection of uric acid by immobilizing Uricase via EDC–NHS coupling. The modified electrodes were characterized by atomic force microscopy (AFM). The response characteristics after immobilization of uricase were studied using cyclic voltammetry and electrochemical impedance spectroscopy techniques. The uricase/PANI/ITO/glass bioelectrode studied by CV and EIS techniques revealed detection of uric acid in a wide range of 0.05 mM to 1.0 mM, covering the physiological range in blood. A low Michaelis–Menten constant (Km) of 0.21 mM indicates the higher affinity of immobilized Uricase towards its analyte (uric acid). The fabricated uric acid biosensor based on PANI LB films exhibits excellent sensitivity of 0.21 mA/mM with a response time of 4 s, good reproducibility, long shelf life (8 weeks) and high selectivity.
Abstract: Meat and meat products for human consumption are one of main sources of protein, amino acids, fatty acids, vitamins, and minerals. Popular variety of meat product is meatballs, which can be enriched with valuable product – Jerusalem artichoke powder, made from dried and grinded Jerusalem artichoke tubers, it is raw material with low-calorie, low fat, rich in dietary fibres, minerals, and vitamins. The results of this study indicate that that people could accept the new product - meatballs with Jerusalem artichoke powder and Jerusalem artichoke powder is suitable for meatballs preparation, in result them is possible to improve meatballs sensory and physical properties.
Abstract: Bacterial molecular chaperone DnaK plays an essential role in protein folding, stress response and transmembrane targeting of proteins. DnaKs from many bacterial species, including Escherichia coli, Salmonella typhimurium and Haemophilus infleunzae are the molecular targets for the insect-derived antimicrobial peptide pyrrhocoricin. Pyrrhocoricin-like peptides bind in the substrate recognition tunnel. Despite the high degree of crossspecies sequence conservation in the substrate-binding tunnel, some bacteria are not sensitive to pyrrhocoricin. This work addresses the molecular mechanism of resistance of Helicobacter pylori DnaK to pyrrhocoricin. Homology modelling, structural and sequence analysis identify a single aminoacid substitution at the interface between the lid and the β-sandwich subdomains of the DnaK substrate-binding domain as the major determinant for its resistance.
Abstract: Thermoplastic starch, polylactic acid glycerol and
maleic anhydride (MA) were compounded with natural
montmorillonite (MMT) through a twin screw extruder to investigate
the effects of different loading of MMT on structure, thermal and
absorption behavior of the nanocomposites. X-ray diffraction analysis
(XRD) showed that sample with MMT loading 4phr exhibited
exfoliated structure while sample that contained MMT 8 phr
exhibited intercalated structure. FESEM images showed big lump
when MMT loading was at 8 phr. The thermal properties were
characterized by using differential scanning calorimeter (DSC). The
results showed that MMT increased melting temperature and
crystallization temperature of matrix but reduction in glass transition
temperature was observed Meanwhile the addition of MMT has
improved the water barrier property. The nanosize MMT particle is
also able to block a tortuous pathway for water to enter the starch
chain, thus reducing the water uptake and improved the physical
barrier of nanocomposite.
Abstract: This paper presents the modeling and simulation of a hybrid proton exchange membrane fuel cell (PEMFC) with an energy storage system for use in a stand-alone distributed generation (DG) system. The simulation model consists of fuel cell DG, lead-acid battery, maximum power point tracking and power conditioning unit which is modeled in the MATLAB/Simulink platform. Poor loadfollowing characteristics and slow response to rapid load changes are some of the weaknesses of PEMFC because of the gas processing reaction and the fuel cell dynamics. To address the load-tracking issues in PEMFC, a hybrid PEMFC and battery storage system is considered and modelled. The model utilizes PEMFC as the main energy source whereas the battery functions as energy storage to compensate for the limitations of PEMFC.Simulation results are given to show the overall system performance under light and heavyloading conditions.
Abstract: Prickly pear (Opuntia spp) fruit has received renewed
interest since it contains a betalain pigment that has an attractive
purple colour for the production of juice. Prickly pear juice was
prepared by homogenizing the fruit and treating the pulp with 48 g of
pectinase from Aspergillus niger. Titratable acidity was determined
by diluting 10 ml prickly pear juice with 90 ml deionized water and
titrating to pH 8.2 with 0.1 N NaOH. Brix was measured using a
refractometer and ascorbic acid content assayed
spectrophotometrically. Colour variation was determined
colorimetrically (Hunter L.a.b.). Hunter L.a.b. analysis showed that
the red purple colour of prickly pear juice had been affected by juice
treatments. This was indicated by low light values of colour
difference meter (CDML*), hue, CDMa* and CDMb* values. It was
observed that non-treated prickly pear juice had a high (colour
difference meter of light) CDML* of 3.9 compared to juice
treatments (range 3.29 to 2.14). The CDML* significantly (p