Abstract: This paper presents a 14-bit cyclic-pipelined Analog to digital converter (ADC) running at 1 MS/s. The architecture is based on a 1.5-bit per stage structure utilizing digital correction for each stage. The ADC consists of two 1.5-bit stages, one shift register delay line, and digital error correction logic. Inside each 1.5-bit stage, there is one gain-boosting op-amp and two comparators. The ADC was implemented in 0.18µm CMOS process and the design has an area of approximately 0.2 mm2. The ADC has a differential input range of 1.2 Vpp. The circuit has an average power consumption of 3.5mA with 10MHz sampling clocks. The post-layout simulations of the design satisfy 12-bit SNDR with a full-scale sinusoid input.
Abstract: The use of a conventional air plasma-sprayed thermal barrier coating (TBC) and a porous, functionally graded TBC as a thermal insulator for Al7075 alloy was explored. A quench test at 1200°C employing fast heating and cooling rates was setup to represent a dynamic thermal condition of an aerospace component. During the test, coated samples were subjected the ambient temperature of 1200°C for a very short time. This was followed by a rapid drop in temperature resulting in cracking of the coatings. For the conventional TBC, it was found that the temperature of the Al7075 substrate decreases with the increase in the ZrO2 topcoat thickness. However, at the topcoat thickness of 1100 µm, large horizontal cracks can be observed in the topcoat and at the topcoat thickness of 1600 µm, the topcoat delaminate during cooling after the quench test. The porous, functionally graded TBC with 600 µm thick topcoat, on the other hand, was found to be as effective at reducing the substrate temperature as the conventional TBC with 1100 µm thick topcoat. The maximum substrate temperature is about 213°C for the former and 208°C for the latter when a heating rate of 38°C/s was used. When the quench tests were conducted with a faster heating rate of 128°C/s, the Al7075 substrate heat up faster with a reduction in the maximum substrate temperatures. The substrate temperatures dropped from 297 to 212°C for the conventional TBC and from 213 to 155°C for the porous TBC, both with 600 µm thick topcoat. Segmentation cracks were observed in both coating after the quench test.
Abstract: In this paper, a robust decentralized congestion control strategy is developed for a large scale network with Differentiated Services (Diff-Serv) traffic. The network is modeled by a nonlinear fluid flow model corresponding to two classes of traffic, namely the premium traffic and the ordinary traffic. The proposed congestion controller does take into account the associated physical network resource limitations and is shown to be robust to the unknown and time-varying delays. Our proposed decentralized congestion control strategy is developed on the basis of Diff-Serv architecture by utilizing a robust adaptive technique. A Linear Matrix Inequality (LMI) condition is obtained to guarantee the ultimate boundedness of the closed-loop system. Numerical simulation implementations are presented by utilizing the QualNet and Matlab software tools to illustrate the effectiveness and capabilities of our proposed decentralized congestion control strategy.
Abstract: Plenty researches have reported techniques to harvest energy from piezoelectric transducer. In the earlier years, the researches mainly report linear energy harvesting techniques whereby interface circuitry is designed to have input impedance that match with the impedance of the piezoelectric transducer. In recent years non-linear techniques become more popular. The non-linear technique employs voltage waveform manipulation to boost the available-for-extraction energy at the time of energy transfer. The fact that non-linear energy extraction provides larger available-for-extraction energy doesn’t mean the linear energy extraction is completely obsolete. In some scenarios, such as where initial power is not available, linear energy extraction is still preferred. A modified Buck Boost circuit which is capable of harvesting piezoelectric energy using both linear and non-linear techniques is reported in this paper. Efficiency of at least 64% can be achieved using this circuit. For linear extraction, the modified Buck Boost circuit is controlled using a fix frequency and duty cycle clock. A voltage sensor and a pulse generator are added as the controller for the non-linear extraction technique.
Abstract: Encouraging physical activity amongst children and adolescents is becoming an increasingly relevant issue in modern society. Studies have shown that involving children and adolescents in physical activity is essential for their physical, mental and social development. However, with technology playing an increasingly important role in reducing physical work it is becoming more critical to incorporate adequate physical activities into our lives. One way to overcome this problem is to harness technology so that it promotes physical activities, for example, by motivating children and adolescents to exercise more. This paper describes a promising solution to the question of how to increase levels of physical activity in children and adolescents by combining gaming technologies with exercise tracking goals. This research describes a framework called FITTER (Framework for Integrating activity Tracking Technologies for Electronic Recreation) that combines video game play with more traditional, non-computer physical activities.
Abstract: A silicon photomultiplier (SiPM) was designed, fabricated and characterized. The SiPM was based on SACM (Separation of Absorption, Charge and Multiplication) structure, which was optimized for blue light detection in application of positron emission tomography (PET). The achieved SiPM array has a high geometric fill factor of 64% and a low breakdown voltage of about 22V, while the temperature dependence of breakdown voltage is only 17mV/°C. The gain and photon detection efficiency of the device achieved were also measured under illumination of light at 405nm and 460nm wavelengths. The gain of the device is in the order of 106. The photon detection efficiency up to 60% has been observed under 1.8V overvoltage.
Abstract: Vetiver oil is secondary metabolite that accumulates in Vetiveria zizanioides roots. The aim of this study was to obtain best type of root culture which produce high amount of vetiver oil, and was similar to metabolites produce from its mother plant. Protein analysis was also conducted to detect protein, related to putative enzymes, which have a role in terpenoids synthesis in the root culture. The results showed that root culture derived from crown explant produced the best root growth. The root culture produced primary and lateral roots, ca. 40 branches. The vetiver oil produced from root culture was analyzed by using GC-MS., and the highest content of terpenoids from roots of crown explant attained 19.024%. The result of SDS PAGE showed proteins which were ±61 kD and ± 68 kD, each might be related to putative monoterpene synthase and sesquiterpenes complex, respectively.
Abstract: This paper presents the design and implementation of a fully integrated Capacitance-to-Voltage Converter (CVC) as the analog front-end for magnetometer interface IC. The application demands very low power solution operating in the frequency of around 20 KHz. The design adapts low power architecture to create low noise electronic interface for Capacitive Micro-machined Lorentz force magnetometer sensor. Using a 0.18-μm CMOS process, simulation results of this interface IC show that the proposed CVC can provide 33 dB closed loop gain, 20 nV/√Hz input referred noise at 20 KHz, while consuming 65 μA current from 1.8-V supply.
Abstract: HfOx based Resistive Random Access Memory (RRAM) is one of the most widely studied material stack due to its promising performances as an emerging memory technology. In this work, we systematically investigated the effect of metal capping layer by preparing sample devices with varying thickness of Ti cap and comparing their operating parameters with the help of an Agilent-B1500A analyzer.
Abstract: The exponential increase in the volume of medical image database has imposed new challenges to clinical routine in maintaining patient history, diagnosis, treatment and monitoring. With the advent of data mining and machine learning techniques it is possible to automate and/or assist physicians in clinical diagnosis. In this research a medical image classification framework using data mining techniques is proposed. It involves feature extraction, feature selection, feature discretization and classification. In the classification phase, the performance of the traditional kNN k nearest neighbor classifier is improved using a feature weighting scheme and a distance weighted voting instead of simple majority voting. Feature weights are calculated using the interestingness measures used in association rule mining. Experiments on the retinal fundus images show that the proposed framework improves the classification accuracy of traditional kNN from 78.57 % to 92.85 %.
Abstract: Darcy’s Law is a well-known constitutive equation describing the flow of a fluid through a porous medium. The equation shows a relationship between the superficial or Darcy velocity and the pressure gradient which was first experimentally observed by Henry Darcy in 1855-1856. In this study, we apply homogenization method to Stokes equation in order to derive Darcy’s Law. The process of deriving the equation is complicated, especially in multidimensional domain. Thus, for the sake of simplicity, we use the indicial notation as well as the homogenization. This combination provides a smooth, simple and easy technique to derive Darcy’s Law.
Abstract: This paper discusses E-government, in particular the challenges that face its development and widespread adoption in Saudi Arabia. E-government can be defined based on an existing set of requirements. E-government has been implemented for a considerable time in developed countries. However, E-government services still face many challenges in their implementation and general adoption in Saudi Arabia. In addition, the literature review and the discussion identify the influential factors, such as quality of service, diffusion of innovation, computer and information literacy, culture, lack of awareness, technical infrastructure, website design, and security, that affect the citizens’ intention to adopt E-government services in Saudi Arabia. Consequently, these factors have been integrated in a new model that would influence citizen to adopt E- government services. Therefore, this research presents an integrated model for ascertaining the intention to adopt E-government services and thereby aiding governments in accessing what is required to increase adoption.
Abstract: The problem of optimal planning of multiple sources
of distributed generation (DG) in distribution networks is treated in
this paper using an improved Ant Colony Optimization algorithm
(ACO). This objective of this problem is to determine the DG
optimal size and location that in order to minimize the network real
power losses. Considering the multiple sources of DG, both size and
location are simultaneously optimized in a single run of the proposed
ACO algorithm. The various practical constraints of the problem are
taken into consideration by the problem formulation and the
algorithm implementation. A radial power flow algorithm for
distribution networks is adopted and applied to satisfy these
constraints. To validate the proposed technique and demonstrate its
effectiveness, the well-know 69-bus feeder standard test system is
employed.cm.
Abstract: In power system protection, the need to know the load
current together with the fault level detected by a relay is important.
This is due to the fact that the relay is required to isolate the
equipment being protected if a fault is present and keep the breaker
associated with it closed if the current level is lower than the
maximum load level. This is not an issue for a radial system. This is
not the same however in a looped power system. In a looped power
system, the isolation of an equipment system will contribute to a
topology change. The change in the power system topology will then
influence or change the maximum load current and the fault level
detected by each relay. In this paper, a method of data collection for
changing topology using matlab and sim-power will be presented.
The method will take into consideration the change in topology and
collect data for each possible topology.
Abstract: An optical chemical sensing film based on
immobilizing of 1,1′- diethyl 2,2′-cyanine (pseudocyanine iodide) in
nafion film was developed for the determination of Fe(III). The
sensing film was homogeneous, transparent, and mechanically stable.
Decrease of the absorbance measured at 518 nm was observed when
the sensing film was immersed in a solution of Fe(III). The optimum
response of the sensing film to Fe(III) was obtained in a solution with
pH 4.0. Linear calibration curve over an Fe(III) concentration range
of 1-30 ppm with a limit of detection of 0.71 ppm was obtained.
Cd(II) is the major interference. The sensing film exhibited good
stability for 2 months and high reproducibility. The proposed method
was applied for the determination of Fe(III) in water samples with
satisfactory results.
Abstract: This study presents a new method for detecting the
cutting tool wear based on the measured cutting force signals using
the regression model and I-kaz method. The detection of tool wear
was done automatically using the in-house developed regression
model and 3D graphic presentation of I-kaz 3D coefficient during
machining process. The machining tests were carried out on a CNC
turning machine Colchester Master Tornado T4 in dry cutting
condition, and Kistler 9255B dynamometer was used to measure the
cutting force signals, which then stored and displayed in the DasyLab
software. The progression of the cutting tool flank wear land (VB)
was indicated by the amount of the cutting force generated. Later, the
I-kaz was used to analyze all the cutting force signals from beginning
of the cut until the rejection stage of the cutting tool. Results of the IKaz
analysis were represented by various characteristic of I-kaz 3D
coefficient and 3D graphic presentation. The I-kaz 3D coefficient
number decreases when the tool wear increases. This method can be
used for real time tool wear monitoring.
Abstract: In this paper, we present a comparative study of the
genetic algorithms and Hessian-s methods for optimal research of the
active powers in an electric network of power. The objective function
which is the performance index of production of electrical energy is
minimized by satisfying the constraints of the equality type and
inequality type initially by the Hessian-s methods and in the second
time by the genetic Algorithms. The results found by the application
of AG for the minimization of the electric production costs of power
are very encouraging. The algorithms seem to be an effective
technique to solve a great number of problems and which are in
constant evolution. Nevertheless it should be specified that the
traditional binary representation used for the genetic algorithms
creates problems of optimization of management of the large-sized
networks with high numerical precision.
Abstract: The electrical power systems of aircrafts have made
serious progress in recent years because the aircrafts depend more
and more on the electricity. There is a trend in the aircraft industry to
replace hydraulic and pneumatic systems with electrical systems,
achieving more comfort and monitoring features and enlarging the
energetic efficiency. Thus, was born the concept More Electric
Aircraft. In this paper is analyzed the integration of a fuel cell into
the existing electrical generation and distribution systems of an
aircraft. The dynamic characteristics of fuel cell systems necessitate
an adaptation of the electrical power system. The architecture studied
in this paper consists of a 50kW fuel cell, a dc to dc converter and
several loads. The dc to dc converter is used to step down the fuel
cell voltage from about 625Vdc to 28Vdc.
Abstract: Purpose: To compare attitudes and perceptions of
Israeli native born mothers versus former Soviet Union (FSU)
immigrant mothers regarding the physical health of their infant.
Methodology: cross-sectional design. A convenience sample of 50
participants was recruited by face to face and snowball technique. A
questionnaire was constructed according to the instructions of the
Ministry of Health for the care and treatment of infants. The main
areas explored were: sources of knowledge that the young mother
acquired regarding the care of her infant, ways of caring for the
infant, hygiene and sanitary habits, and the pattern of referral to
health professionals. The last topic relates to emotions mothers might
experience towards their infant.
Results: Mothers from both cultural groups present some similar
caring behaviors, which may express a universal aspect of mothers'
behavior towards their infants. However, immigrant mothers differ
significantly from native born by relying less on their mothers' and
grandmothers' experience, they wean their infants from diapers
earlier, they are stricter about hygiene and sanitary habits and they
tend to consult a physician when their infant has low fever. Native
born and immigrant mothers differ in their expressions of pride and
wonder. Immigrant mothers report of a lesser degree of these
emotions towards their infants than native born mothers.
Conclusion: The theoretical model of socialization and
acculturation of immigrant mothers is employed as an explanatory
model for the current findings Young immigrant mothers undergo a
complex acculturation process and adapt behavioral patterns in
various areas to comply with Israeli norms and values, demonstrating
assimilation. In other areas they adhere to the norms of their original
culture.
Abstract: Now a days video data embedding approach is a very challenging and interesting task towards keeping real time video data secure. We can implement and use this technique with high-level applications. As the rate-distortion of any image is not confirmed, because the gain provided by accurate image frame segmentation are balanced by the inefficiency of coding objects of arbitrary shape, with a lot factors like losses that depend on both the coding scheme and the object structure. By using rate controller in association with the encoder one can dynamically adjust the target bitrate. This paper discusses about to keep secure videos by mixing signature data with negligible distortion in the original video, and to keep steganographic video as closely as possible to the quality of the original video. In this discussion we propose the method for embedding the signature data into separate video frames by the use of block Discrete Cosine Transform. These frames are then encoded by real time encoding H.264 scheme concepts. After processing, at receiver end recovery of original video and the signature data is proposed.