Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.
Abstract: In this work we study analytically and numerically the
performance of the mean heave motion of an OWC coupled with the
governing equation of the spreading ocean waves due to the wide
variation in an open parabolic channel with constant depth. This
paper considers that the ocean wave propagation is under the
assumption of a shallow flow condition. In order to verify the effect
of the waves in the OWC firstly we establish the analytical model in
a non-dimensional form based on the energy equation. The proposed
wave-power system has to aims: one is to perturb the ocean waves as
a consequence of the channel shape in order to concentrate the
maximum ocean wave amplitude in the neighborhood of the OWC
and the second is to determine the pressure and volume oscillation of
air inside the compression chamber.
Abstract: This paper considers the exclusion of consumer rights by the New Zealand Consumer Guarantees Act 1993 in eauctions. The paper asserts that the absence of an individual auctioneer conducting each e-auction means that e-auctions may not be auctions at all. The paper also questions the justification for excluding consumer rights in e-auctions because the rationale for excluding consumer rights in traditional auctions does not fit with e-auctions due to the significant differences in the sale processes. The paper recommends reform by way of statutory amendment.
Abstract: This paper presents a new algorithm for the channel estimation of the OFDM system based on a pilot signal for the new generation of high data rate communication systems. In orthogonal frequency division multiplexing (OFDM) systems over fast-varying fading channels, channel estimation and tracking is generally carried out by transmitting known pilot symbols in given positions of the frequency-time grid. In this paper, we propose to derive an improved algorithm based on the calculation of the mean and the variance of the adjacent pilot signals for a specific distribution of the pilot signals in the OFDM frequency-time grid then calculating of the entire unknown channel coefficients from the equation of the mean and the variance. Simulation results shows that the performance of the OFDM system increase as the length of the channel increase where the accuracy of the estimated channel will be increased using this low complexity algorithm, also the number of the pilot signal needed to be inserted in the OFDM signal will be reduced which lead to increase in the throughput of the signal over the OFDM system in compared with other type of the distribution such as Comb type and Block type channel estimation.
Abstract: The standard investigational method for obstructive
sleep apnea syndrome (OSAS) diagnosis is polysomnography (PSG),
which consists of a simultaneous, usually overnight recording of
multiple electro-physiological signals related to sleep and
wakefulness. This is an expensive, encumbering and not a readily
repeated protocol, and therefore there is need for simpler and easily
implemented screening and detection techniques. Identification of
apnea/hypopnea events in the screening recordings is the key factor
for the diagnosis of OSAS. The analysis of a solely single-lead
electrocardiographic (ECG) signal for OSAS diagnosis, which may
be done with portable devices, at patient-s home, is the challenge of
the last years. A novel artificial neural network (ANN) based
approach for feature extraction and automatic identification of
respiratory events in ECG signals is presented in this paper. A
nonlinear principal component analysis (NLPCA) method was
considered for feature extraction and support vector machine for
classification/recognition. An alternative representation of the
respiratory events by means of Kohonen type neural network is
discussed. Our prospective study was based on OSAS patients of the
Clinical Hospital of Pneumology from Iaşi, Romania, males and
females, as well as on non-OSAS investigated human subjects. Our
computed analysis includes a learning phase based on cross signal
PSG annotation.
Abstract: Malting is usually carried out on intact barley seed,
while hull is still attached to it. In this study, oat grain with and
without hull was subjected to controlled germination to optimize its
enzymes activity, in such a way that lipase has the lowest and α-
amylase and proteinase the highest activities. Since pH has a great
impact on the activity of the enzymes, the pH of germination media
was set up to 3 to 8. In dehulled oats, lipase and α-amylase had the
lowest and highest activities in pHs 3 and 6, respectively whereas the
highest proteinase activity was evidenced at pH 7 and 4 in the oats
with and without hull respectively. While measurements indicated
that the effect of hull on the enzyme activities particularly in lipase
and amylase at each level of the pH are significantly different, the
best results were obtained in those samples in which their hull had
been removed. However, since the similar lipase activity in
germinated dehulled oat were recorded at the pHs 4 and 5, therefore
it was concluded that pH 5 in dehulled oat seed may provide the
optimum enzyme activity for all the enzymes.
Abstract: Discovering new biological knowledge from the highthroughput biological data is a major challenge to bioinformatics today. To address this challenge, we developed a new approach for protein classification. Proteins that are evolutionarily- and thereby functionally- related are said to belong to the same classification. Identifying protein classification is of fundamental importance to document the diversity of the known protein universe. It also provides a means to determine the functional roles of newly discovered protein sequences. Our goal is to predict the functional classification of novel protein sequences based on a set of features extracted from each protein sequence. The proposed technique used datasets extracted from the Structural Classification of Proteins (SCOP) database. A set of spectral domain features based on Fast Fourier Transform (FFT) is used. The proposed classifier uses multilayer back propagation (MLBP) neural network for protein classification. The maximum classification accuracy is about 91% when applying the classifier to the full four levels of the SCOP database. However, it reaches a maximum of 96% when limiting the classification to the family level. The classification results reveal that spectral domain contains information that can be used for classification with high accuracy. In addition, the results emphasize that sequence similarity measures are of great importance especially at the family level.
Abstract: Maize and Indian mustard are significant crops in
semi-arid climate zones of India. Improved water management
requires precise scheduling of irrigation, which in turn requires an
accurate computation of daily crop evapotranspiration (ETc). Daily
crop evapotranspiration comes as a product of reference
evapotranspiration (ET0) and the growth stage specific crop
coefficients modified for daily variation. The first objective of
present study is to develop crop coefficients Kc for Maize and Indian
mustard. The estimated values of Kc for maize at the four crop
growth stages (initial, development, mid-season, and late season) are
0.55, 1.08, 1.25, and 0.75, respectively, and for Indian mustard the Kc
values at the four growth stages are 0.3, 0.6, 1.12, and 0.35,
respectively. The second objective of the study is to compute daily
crop evapotranspiration from ET0 and crop coefficients. Average
daily ETc of maize varied from about 2.5 mm/d in the early growing
period to > 6.5 mm/d at mid season. The peak ETc of maize is 8.3
mm/d and it occurred 64 days after sowing at the reproductive growth
stage when leaf area index was 4.54. In the case of Indian mustard,
average ETc is 1 mm/d at the initial stage, >1.8 mm/d at mid season
and achieves a peak value of 2.12 mm/d on 56 days after sowing.
Improved schedules of irrigation have been simulated based on daily
crop evapo-transpiration and field measured data. Simulation shows a
close match between modeled and field moisture status prevalent
during crop season.
Abstract: Renewed interest in propeller propulsion on aircraft
configurations combined with higher propeller loads lead to the question how the effects of the propulsion on model support disturbances
should be accounted for. In this paper, the determination of engine power effects on support interference of sting-mounted models is
demonstrated by a measurement on a four-engine turboprop aircraft.
CFD results on a more generic model are presented in order to clarify
the possible mechanism behind engine power effects on support
interference. The engine slipstream induces a local change in angle
of sideslip at the model sting thereby influencing the sting near-field and far-field effects. Whether or not the net result of these changes
in the disturbance pattern leads to a significant engine power effect depends on the configuration of the wind tunnel model and the test
setup.
Abstract: This paper presented two new efficient algorithms
for contour approximation. The proposed algorithm is compared
with Ramer (good quality), Triangle (faster) and Trapezoid (fastest)
in this work; which are briefly described. Cartesian co-ordinates of
an input contour are processed in such a manner that finally
contours is presented by a set of selected vertices of the edge of the
contour. In the paper the main idea of the analyzed procedures for
contour compression is performed. For comparison, the mean
square error and signal-to-noise ratio criterions are used.
Computational time of analyzed methods is estimated depending on
a number of numerical operations. Experimental results are
obtained both in terms of image quality, compression ratios, and
speed. The main advantages of the analyzed algorithm is small
numbers of the arithmetic operations compared to the existing
algorithms.
Abstract: This paper proposes the method combining artificial
neural network (ANN) with particle swarm optimization (PSO) to
implement the maximum power point tracking (MPPT) by controlling
the rotor speed of the wind generator. First, the measurements of wind
speed, rotor speed of wind power generator and output power of wind
power generator are applied to train artificial neural network and to
estimate the wind speed. Second, the method mentioned above is
applied to estimate and control the optimal rotor speed of the wind
turbine so as to output the maximum power. Finally, the result reveals
that the control system discussed in this paper extracts the maximum
output power of wind generator within the short duration even in the
conditions of wind speed and load impedance variation.
Abstract: The aim of this study was to remove the two principal
noises which disturb the surface electromyography signal
(Diaphragm). These signals are the electrocardiogram ECG artefact
and the power line interference artefact. The algorithm proposed
focuses on a new Lean Mean Square (LMS) Widrow adaptive
structure. These structures require a reference signal that is correlated
with the noise contaminating the signal. The noise references are
then extracted : first with a noise reference mathematically
constructed using two different cosine functions; 50Hz (the
fundamental) function and 150Hz (the first harmonic) function for
the power line interference and second with a matching pursuit
technique combined to an LMS structure for the ECG artefact
estimation. The two removal procedures are attained without the use
of supplementary electrodes. These techniques of filtering are
validated on real records of surface diaphragm electromyography
signal. The performance of the proposed methods was compared with
already conducted research results.
Abstract: Information Technology (IT) projects are always
accompanied by various risks and because of high rate of failure in
such projects, managing risks in order to neutralize or at least
decrease their effects on the success of the project is strongly
essential. In this paper, fuzzy analytical hierarchy process (FAHP) is
exploited as a means of risk evaluation methodology to prioritize and
organize risk factors faced in IT projects. A real case of IT projects, a
project of design and implementation of an integrated information
system in a vehicle producing company in Iran is studied. Related
risk factors are identified and then expert qualitative judgments about
these factors are acquired. Translating these judgments to fuzzy
numbers and using them as an input to FAHP, risk factors are then
ranked and prioritized by FAHP in order to make project managers
aware of more important risks and enable them to adopt suitable
measures to deal with these highly devastative risks.
Abstract: This paper describes a new measuring algorithm for
three-dimensional (3-D) braided composite material .Braided angle is
an important parameter of braided composites. The objective of this
paper is to present an automatic measuring system. In the paper, the
algorithm is performed by using vcµ6.0 language on PC. An
advanced filtered algorithm for image of 3-D braided composites
material performs has been developed. The procedure is completely
automatic and relies on the gray scale information content of the
images and their local wavelet transform modulus maxims.
Experimental results show that the proposed method is feasible.
The algorithm was tested on both carbon-fiber and glass-fiber
performs.
Abstract: The forest stand consisted of four layers. The species
composition between the third and the bottom layers was almost
similar, whereas it was almost exclusive between the top and the lower
three layers. The values of Shannon-s index H' and Pielou-s index
J ' tended to increase from the bottom layer upward, except for
H' -value of the top layer. The values of H' and J ' were 4.21 bit
and 0.73, respectively, for the total stand. High woody species
diversity of the forest depended on large trees in the upper layers,
which trend was different from a subtropical evergreen broadleaf
forest grown in silicate habitat in the northern part of Okinawa Island.
The spatial distribution of trees was overlapped between the third and
the bottom layers, whereas it was independent or slightly exclusive
between the top and the lower three layers. Mean tree weight of each
layer decreased from the top toward the bottom layer, whereas the
corresponding tree density increased from the top downward. This
relationship was analogous to the process of self-thinning plant
populations.
Abstract: The paper presented a transient population dynamics of phase singularities in 2D Beeler-Reuter model. Two stochastic modelings are examined: (i) the Master equation approach with the transition rate (i.e., λ(n, t) = λ(t)n and μ(n, t) = μ(t)n) and (ii) the nonlinear Langevin equation approach with a multiplicative noise. The exact general solution of the Master equation with arbitrary time-dependent transition rate is given. Then, the exact solution of the mean field equation for the nonlinear Langevin equation is also given. It is demonstrated that transient population dynamics is successfully identified by the generalized Logistic equation with fractional higher order nonlinear term. It is also demonstrated the necessity of introducing time-dependent transition rate in the master equation approach to incorporate the effect of nonlinearity.
Abstract: In this paper, vapour-liquid critical locus for the
binary system acetone + chloroform was determined experimentally
over the whole range of composition. The critical property
measurements were carried out using a dynamic-synthetic apparatus,
employed in the dynamic mode. The critical points are visually
determined by observing the critical opalescence and the
simultaneous disappearance and reappearance of the meniscus in the
middle of a high-pressure view cell which withstands operations up
to 673K and 20MPa. The experimental critical points measured in
this work were compared to those available in literature.
Abstract: The article deals with pneumatic and hot wire
anemometry measurement on subsonic axi-symmetric air ejector.
Performances of the ejector with and without pulsations of primary
flow are compared, measuring of characteristic pressures and mass
flow rates are performed and ejector efficiency is evaluated. The
pulsations of primary flow are produced by a synthetic jet generator,
which is placed in the supply line of the primary flow just in front of
the primary nozzle. The aim of the pulsation is to intensify the
mixing process. In the article we present: Pressure measuring of
pulsation on the mixing chamber wall, behind the mixing chamber
and behind the diffuser measured by fast pressure transducers and
results of hot wire anemometry measurement. It was found out that
using of primary flow pulsations yields higher back pressure behind
the ejector and higher efficiency. The processes in this ejector and
influences of primary flow pulsations on the mixing processes are
described.
Abstract: This paper investigates the optimization problem of
multi-product aggregate production planning (APP) with fuzzy data.
From a comprehensive viewpoint of conserving the fuzziness of input
information, this paper proposes a method that can completely
describe the membership function of the performance measure. The
idea is based on the well-known Zadeh-s extension principle which
plays an important role in fuzzy theory. In the proposed solution
procedure, a pair of mathematical programs parameterized by
possibility level a is formulated to calculate the bounds of the
optimal performance measure at a . Then the membership function of
the optimal performance measure is constructed by enumerating
different values of a . Solutions obtained from the proposed method
contain more information, and can offer more chance to achieve the
feasible disaggregate plan. This is helpful to the decision-maker in
practical applications.
Abstract: In the previous multi-solid models,¤ò approach is
used for the calculation of fugacity in the liquid phase. For the first
time, in the proposed multi-solid thermodynamic model,γ approach
has been used for calculation of fugacity in the liquid mixture.
Therefore, some activity coefficient models have been studied that
the results show that the predictive Wilson model is more appropriate
than others. The results demonstrate γ approach using the predictive
Wilson model is in more agreement with experimental data than the
previous multi-solid models. Also, by this method, generates a new
approach for presenting stability analysis in phase equilibrium
calculations. Meanwhile, the run time in γ approach is less than the
previous methods used ¤ò approach. The results of the new model
present 0.75 AAD % (Average Absolute Deviation) from the
experimental data which is less than the results error of the previous
multi-solid models obviously.